-- extracted from draft-ietf-adslmib-adslext-07.txt -- at Fri Apr 13 06:05:05 2001 ADSL-LINE-EXT-MIB DEFINITIONS ::= BEGIN IMPORTS Counter32, Unsigned32, NOTIFICATION-TYPE, MODULE-IDENTITY, Gauge32, OBJECT-TYPE, mib-2 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION FROM SNMPv2-TC PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB AdslPerfCurrDayCount, AdslPerfPrevDayCount, AdslPerfTimeElapsed, AdslLineCodingType FROM ADSL-TC-MIB ifIndex FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB adslLineAlarmConfProfileEntry, adslLineConfProfileEntry, adslAturIntervalEntry, adslAturPerfDataEntry, adslAtucIntervalEntry, adslAtucPerfDataEntry, adslLineEntry, adslMIB FROM ADSL-LINE-MIB ; adslExtMIB MODULE-IDENTITY LAST-UPDATED "200104090000Z" ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO " Faye Ly Salira Optical Systems 2698 Orchard Parkway San Jose, CA 95134 Tel: +1 408-382-0088 Fax: +1 408-382-1688 E-Mail: faye@salira.com Gregory Bathrick NOKIA High Speed Access Nodes 1310 Redwood Way, Petaluma, CA 94954, USA Tel: +1 707-793-7030 Fax: +1 707-792-0850 E-Mail: greg.bathrick@nokia.com IETF ADSL MIB Working Group (XDSLMIB@LISTSERV.ECIRALEIGH.COM> " DESCRIPTION "This MIB Module is a supplement to the ADSL-LINE-MIB [RFC2662]." ::= { adslMIB 3 } adslExtMibObjects OBJECT IDENTIFIER ::= { adslExtMIB 1 } AdslTransmissionModeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A set of ADSL line transmission modes, with one bit per mode. The notes (F) and (L) denote Full-Rate and Lite respectively: Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 02 : G.992.1 POTS non-overlapped (F) Bit 03 : G.992.1 POTS overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 08 : G.992.2 POTS non-overlapped (L) Bit 09 : G.992.2 POTS overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 12 : G.992.1 TCM-ISDN symmetric (F) " SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12) } adslLineExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ADSL line configuration and monitoring information not defined in the adslLineTable from the ADSL-LINE-MIB [RFC2662]. This includes the capabilities and actual ADSL transmission system." ::= { adslExtMibObjects 17 } adslLineExtEntry OBJECT-TYPE SYNTAX AdslLineExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslLineEntry } ::= { adslLineExtTable 1 } AdslLineExtEntry ::= SEQUENCE { adslLineTransAtucCap AdslTransmissionModeType, adslLineTransAtucConfig AdslTransmissionModeType, adslLineTransAtucActual AdslTransmissionModeType, adslLineGlitePowerState INTEGER, adslLineConfProfileDualLite SnmpAdminString } adslLineTransAtucCap OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission modes that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment." REFERENCE "Section 7.3.2 ITU G.997.1" ::= { adslLineExtEntry 1 } adslLineTransAtucConfig OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission modes that the ATU-C must enable for the line. The ATU-C's enable modes must be a subset of its capable modes." REFERENCE "Section 7.3.2 ITU G.997.1" ::= { adslLineExtEntry 2 } adslLineTransAtucActual OBJECT-TYPE SYNTAX AdslTransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission mode of the ATU-C. This object returns 0 (i.e BITS with no mode bit set) if there is no mode currently known. The initialization with the ATU-R will determine the mode used and the result must be a one-mode subset of the 'Enable' modes. After an initialization has occurred, its mode is saved as the 'Current' mode and it should persist even if the link goes down subsequently. This leaves a hint on what may be used next time." REFERENCE "Section 7.3.2 ITU G.997.1 " ::= { adslLineExtEntry 3 } adslLineGlitePowerState OBJECT-TYPE SYNTAX INTEGER { none(1), l0(2), -- L0 Power on l1(3), -- L1 Power on but reduced l3(4) -- L3 Power off } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object specifies the power state this interface is in. If the object adslLineModeActual is set to glite, the value of this object can be either one of the power state from L0 to L3. If the object adslLineTransAtucActual is set to other than G.lite, the value of this object is always set to none(1)." ::= { adslLineExtEntry 4 } adslLineConfProfileDualLite OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable, when the mode after initialization is any G.992.2 (G.lite) mode AND adslLineTransAtucConfig has enabled dual-mode. Dual-mode in this case means one or more Full-Rate modes AND one or more Lite modes enabled. If dual-mode has not been enabled by this MIB or if the ATU-C does not support this extension MIB, then the previously existing adslLineConfProfile is used even if the ATU-C mode is one of the G.992.2 modes." ::= { adslLineExtEntry 5 } adslAtucPerfDataExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ADSL physical line counters information not defined in the adslAtucPerfDataTable from the ADSL-LINE-MIB [RFC2662]." ::= { adslExtMibObjects 18 } adslAtucPerfDataExtEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslAtucPerfDataEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslAtucPerfDataEntry } ::= { adslAtucPerfDataExtTable 1 } AdslAtucPerfDataExtEntry ::= SEQUENCE { adslAtucPerfStatFastR Counter32, adslAtucPerfStatFailedFastR Counter32, adslAtucPerfStatSesL Counter32, adslAtucPerfStatUasL Counter32, adslAtucPerfCurr15MinFastR PerfCurrentCount, adslAtucPerfCurr15MinFailedFastR PerfCurrentCount, adslAtucPerfCurr15MinSesL PerfCurrentCount, adslAtucPerfCurr15MinUasL PerfCurrentCount, adslAtucPerfCurr1DayFastR AdslPerfCurrDayCount, adslAtucPerfCurr1DayFailedFastR AdslPerfCurrDayCount, adslAtucPerfCurr1DaySesL AdslPerfCurrDayCount, adslAtucPerfCurr1DayUasL AdslPerfCurrDayCount, adslAtucPerfPrev1DayFastR AdslPerfPrevDayCount, adslAtucPerfPrev1DayFailedFastR AdslPerfPrevDayCount, adslAtucPerfPrev1DaySesL AdslPerfPrevDayCount, adslAtucPerfPrev1DayUasL AdslPerfPrevDayCount } adslAtucPerfStatFastR OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 1 } adslAtucPerfStatFailedFastR OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of failed fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 2 } adslAtucPerfStatSesL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of severely errored second-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 3 } adslAtucPerfStatUasL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of unavailable second." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 4 } adslAtucPerfCurr15MinFastR OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 5 } adslAtucPerfCurr15MinFailedFastR OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was failed fast retrains." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 6 } adslAtucPerfCurr15MinSesL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was fast retrains." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 7 } adslAtucPerfCurr15MinUasL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was count for unavailable errored seconds." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 8 } adslAtucPerfCurr1DayFastR OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was fast retrains during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 9 } adslAtucPerfCurr1DayFailedFastR OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was failed fast retrains during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 10 } adslAtucPerfCurr1DaySesL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Severe Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 11 } adslAtucPerfCurr1DayUasL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Unavailable Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 12 } adslAtucPerfPrev1DayFastR OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was fast retrains within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.4.15.1 " ::= { adslAtucPerfDataExtEntry 13 } adslAtucPerfPrev1DayFailedFastR OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was failed fast retrains within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.4.15.2 " ::= { adslAtucPerfDataExtEntry 14 } adslAtucPerfPrev1DaySesL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was severed errored seconds within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAtucPerfDataExtEntry 15 } adslAtucPerfPrev1DayUasL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was unavailable errored seconds within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.2.1.1.9 " ::= { adslAtucPerfDataExtEntry 16 } adslAtucIntervalExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslExtMibObjects 19 } adslAtucIntervalExtEntry OBJECT-TYPE SYNTAX AdslAtucIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalExtTable." AUGMENTS { adslAtucIntervalEntry } ::= { adslAtucIntervalExtTable 1 } AdslAtucIntervalExtEntry ::= SEQUENCE { adslAtucIntervalFastR PerfIntervalCount, adslAtucIntervalFailedFastR PerfIntervalCount, adslAtucIntervalSesL PerfIntervalCount, adslAtucIntervalUasL PerfIntervalCount } adslAtucIntervalFastR OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Fast Retrains." ::= { adslAtucIntervalExtEntry 1 } adslAtucIntervalFailedFastR OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Failed Fast Retrains." ::= { adslAtucIntervalExtEntry 2 } adslAtucIntervalSesL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was severed errors." ::= { adslAtucIntervalExtEntry 3 } adslAtucIntervalUasL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was unavailable errors." ::= { adslAtucIntervalExtEntry 4 } adslAturPerfDataExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ADSL physical line counters information not defined in the adslAturPerfDataTable from the ADSL-LINE-MIB [RFC2662]." ::= { adslExtMibObjects 20 } adslAturPerfDataExtEntry OBJECT-TYPE SYNTAX AdslAturPerfDataExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslAturPerfDataEntry defined in [RFC2662]. Each entry corresponds to an ADSL line." AUGMENTS { adslAturPerfDataEntry } ::= { adslAturPerfDataExtTable 1 } AdslAturPerfDataExtEntry ::= SEQUENCE { adslAturPerfStatSesL Counter32, adslAturPerfStatUasL Counter32, adslAturPerfCurr15MinSesL PerfCurrentCount, adslAturPerfCurr15MinUasL PerfCurrentCount, adslAturPerfCurr1DaySesL AdslPerfCurrDayCount, adslAturPerfCurr1DayUasL AdslPerfCurrDayCount, adslAturPerfPrev1DaySesL AdslPerfPrevDayCount, adslAturPerfPrev1DayUasL AdslPerfPrevDayCount } adslAturPerfStatSesL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of severely errored second-line." REFERENCE "ITU G.997.1 Section 7.2.1.1.7 " ::= { adslAturPerfDataExtEntry 1 } adslAturPerfStatUasL OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object indicates the count of unavailable second." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 2 } adslAturPerfCurr15MinSesL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Severe Errored Seconds-Line." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 3 } adslAturPerfCurr15MinUasL OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Unavailable Errored Seconds." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 4 } adslAturPerfCurr1DaySesL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Severe Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 5 } adslAturPerfCurr1DayUasL OBJECT-TYPE SYNTAX AdslPerfCurrDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Unavailable Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 6 } adslAturPerfPrev1DaySesL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was severed errored second within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.2.1.2.7 " ::= { adslAturPerfDataExtEntry 7 } adslAturPerfPrev1DayUasL OBJECT-TYPE SYNTAX AdslPerfPrevDayCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was unavailable errored second within the most recent previous 1-day period." REFERENCE "ITU G.997.1 Section 7.2.1.2.9 " ::= { adslAturPerfDataExtEntry 8 } adslAturIntervalExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslExtMibObjects 21 } adslAturIntervalExtEntry OBJECT-TYPE SYNTAX AdslAturIntervalExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalExtTable." AUGMENTS { adslAturIntervalEntry } ::= { adslAturIntervalExtTable 1 } AdslAturIntervalExtEntry ::= SEQUENCE { adslAturIntervalSesL PerfIntervalCount, adslAturIntervalUasL PerfIntervalCount } adslAturIntervalSesL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was severed errors." ::= { adslAturIntervalExtEntry 1 } adslAturIntervalUasL OBJECT-TYPE SYNTAX PerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was unavailable errors." ::= { adslAturIntervalExtEntry 2 } adslConfProfileExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ADSL line profile configuration information not defined in the adslLineConfProfileTable from the ADSL-LINE-MIB [RFC2662]. This includes the line mode." ::= { adslExtMibObjects 22 } adslConfProfileExtEntry OBJECT-TYPE SYNTAX AdslConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineConfProfileEntry defined in [RFC2662]. Each entry corresponds to an ADSL line profile." AUGMENTS { adslLineConfProfileEntry } ::= { adslConfProfileExtTable 1 } AdslConfProfileExtEntry ::= SEQUENCE { adslConfProfileLineType INTEGER } adslConfProfileLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- fast channel exists only interleavedOnly (3), -- interleaved channel exists -- only fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both fast or interleaved -- channels exist } MAX-ACCESS read-create STATUS current DESCRIPTION " This object is used to configure the ADSL physical line mode. " ::= { adslConfProfileExtEntry 1 } adslAlarmConfProfileExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAlarmConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table extends the adslLineAlarmConfProfileTable and provides threshold parameters for all the counters defined in this MIB module." ::= { adslExtMibObjects 23 } adslAlarmConfProfileExtEntry OBJECT-TYPE SYNTAX AdslAlarmConfProfileExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry extends the adslLineAlarmConfProfileTable defined in [RFC2662]. Each entry corresponds to an ADSL alarm profile." AUGMENTS { adslLineAlarmConfProfileEntry } ::= { adslAlarmConfProfileExtTable 1 } AdslAlarmConfProfileExtEntry ::= SEQUENCE { adslAtucThreshold15MinFailedFastR Unsigned32, adslAtucThreshold15MinSesL Unsigned32, adslAtucThreshold15MinUasL Unsigned32 } adslAtucThreshold15MinFailedFastR OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of failed retrains encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucFailedFastRTrap. One trap will be sent per interval per interface. A value '0' will disable the trap." ::= { adslAlarmConfProfileExtEntry 1 } adslAtucThreshold15MinSesL OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Severe errored seconds encountered by an ADSL interface withing any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucSesLTrap. One trap will be sent per interval per interface. A value '0' will disable the trap." ::= { adslAlarmConfProfileExtEntry 2 } adslAtucThreshold15MinUasL OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of unavailable errored seconds encountered by an ADSL interface withing any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucUasLThreshTrap. One trap will be sent per interval per interface. A value '0' will disable the trap." ::= { adslAlarmConfProfileExtEntry 3 } -- trap definitions adslExtTraps OBJECT IDENTIFIER ::= { adslExtMibObjects 24 } adslExtAtucTraps OBJECT IDENTIFIER ::= { adslExtTraps 1 } adslAtucFailedFastRThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinFailedFastR } STATUS current DESCRIPTION "Failed Fast Retrains 15 minutes threshold reached." ::= { adslExtAtucTraps 0 1 } adslAtucSesLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinSesL } STATUS current DESCRIPTION "Severe errored seconds 15 minutes threshold reached." ::= { adslExtAtucTraps 0 2 } adslAtucUasLThreshTrap NOTIFICATION-TYPE OBJECTS { adslAtucPerfCurr15MinUasL } STATUS current DESCRIPTION "Unavailable seconds 15 minutes threshold reached." ::= { adslExtAtucTraps 0 3 } -- conformance information adslExtConformance OBJECT IDENTIFIER ::= { adslExtMIB 2 } adslExtGroups OBJECT IDENTIFIER ::= { adslExtConformance 1 } adslExtCompliances OBJECT IDENTIFIER ::= { adslExtConformance 2 } -- ATU-C agent compliance statements adslExtLineMibAtucCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage ADSL ATU-C interfaces." MODULE -- this module MANDATORY-GROUPS { adslExtLineGroup, adslExtLineConfProfileControlGroup, adslExtLineAlarmConfProfileGroup } GROUP adslExtAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-C physical event counters should implement this group." GROUP adslExtAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional. Implementations which require continuous ATU-R physical event counters should implement this group." OBJECT adslAtucThreshold15MinFailedFastR MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshold15MinSesL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslAtucThreshold15MinUasL MIN-ACCESS read-write DESCRIPTION "Read-write access is applicable when static profiles are implemented." OBJECT adslLineConfProfileDualLite MIN-ACCESS read-only DESCRIPTION "Read-only access is applicable when static profiles are implemented." ::= { adslExtCompliances 1 } -- units of conformance adslExtLineGroup OBJECT-GROUP OBJECTS { adslLineConfProfileDualLite, adslLineTransAtucCap, adslLineTransAtucConfig, adslLineTransAtucActual, adslLineGlitePowerState } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line." ::= { adslExtGroups 1 } adslExtAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfStatFastR, adslAtucPerfStatFailedFastR, adslAtucPerfCurr15MinFastR, adslAtucPerfCurr15MinFailedFastR, adslAtucPerfCurr1DayFastR, adslAtucPerfCurr1DayFailedFastR, adslAtucPerfPrev1DayFastR, adslAtucPerfPrev1DayFailedFastR, adslAtucPerfStatSesL, adslAtucPerfStatUasL, adslAtucPerfCurr15MinSesL, adslAtucPerfCurr15MinUasL, adslAtucPerfCurr1DaySesL, adslAtucPerfCurr1DayUasL, adslAtucPerfPrev1DaySesL, adslAtucPerfPrev1DayUasL, adslAtucIntervalFastR, adslAtucIntervalFailedFastR, adslAtucIntervalSesL, adslAtucIntervalUasL } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslExtGroups 2 } adslExtAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfStatSesL, adslAturPerfStatUasL, adslAturPerfCurr15MinSesL, adslAturPerfCurr15MinUasL, adslAturPerfCurr1DaySesL, adslAturPerfCurr1DayUasL, adslAturPerfPrev1DaySesL, adslAturPerfPrev1DayUasL, adslAturIntervalSesL, adslAturIntervalUasL } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." ::= { adslExtGroups 3 } adslExtLineConfProfileControlGroup OBJECT-GROUP OBJECTS { adslConfProfileLineType } STATUS current DESCRIPTION "A collection of objects providing profile control for the ADSL system." ::= { adslExtGroups 4 } adslExtLineAlarmConfProfileGroup OBJECT-GROUP OBJECTS { adslAtucThreshold15MinFailedFastR, adslAtucThreshold15MinSesL, adslAtucThreshold15MinUasL } STATUS current DESCRIPTION "A collection of objects providing alarm profile control for the ADSL system." ::= { adslExtGroups 5 } adslExtNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { adslAtucFailedFastRThreshTrap, adslAtucSesLThreshTrap, adslAtucUasLThreshTrap } STATUS current DESCRIPTION "The collection of ADSL 2 notifications." ::= { adslExtGroups 6 } END -- -- Copyright (C) The Internet Society (2001). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this -- document itself may not be modified in any way, such as by removing -- the copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of -- developing Internet standards in which case the procedures for -- copyrights defined in the Internet Standards process must be -- followed, or as required to translate it into languages other than -- English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- This document and the information contained herein is provided on an -- "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING -- TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING -- BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION -- HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF -- MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. --