-- extracted from rfc4706.txt -- at Wed Nov 29 06:07:30 2006 ADSL2-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, transmission, Unsigned32, NOTIFICATION-TYPE, Integer32, Counter32 FROM SNMPv2-SMI ifIndex FROM IF-MIB TruthValue, RowStatus FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB HCPerfIntervalThreshold, HCPerfTimeElapsed FROM HC-PerfHist-TC-MIB -- [RFC3705] Adsl2Unit, Adsl2Direction, Adsl2TransmissionModeType, Adsl2RaMode, Adsl2InitResult, Adsl2OperationModes, Adsl2PowerMngState, Adsl2ConfPmsForce, Adsl2LConfProfPmMode, Adsl2LineLdsf, Adsl2LdsfResult, Adsl2SymbolProtection, Adsl2MaxBer, Adsl2ScMaskDs, Adsl2ScMaskUs, Adsl2RfiDs, Adsl2PsdMaskDs, Adsl2PsdMaskUs, Adsl2Tssi, Adsl2LastTransmittedState, Adsl2LineStatus, Adsl2ChAtmStatus, Adsl2ChPtmStatus FROM ADSL2-LINE-TC-MIB -- [This document] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; adsl2MIB MODULE-IDENTITY LAST-UPDATED "200610040000Z" -- October 4th, 2006 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-Chair & Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: mbdodge@ieee.org Phone: +972 3 926 8421 Co-editor: Moti Morgenstern ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: moti.morgenstern@ecitele.com Phone: +972 3 926 6258 Co-editor: Scott Baillie NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: scott.baillie@nec.com.au Phone: +61 3 9264 3986 Co-editor: Umberto Bonollo NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: umberto.bonollo@nec.com.au Phone: +61 3 9264 3385 " DESCRIPTION " This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1am1] and [G.997.1am2]. Note that the revised ITU-T G.997.1 standard also refers to the next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the IANA Considerations section of this document. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices." REVISION "200610040000Z" -- October 4th, 2006 DESCRIPTION "Initial version, published as RFC 4706." ::= { transmission 238 } adsl2 OBJECT IDENTIFIER ::= { adsl2MIB 1 } ------------------------------------------------ adsl2Line OBJECT IDENTIFIER ::= { adsl2 1 } adsl2Status OBJECT IDENTIFIER ::= { adsl2 2 } adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 3 } adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 } adsl2Profile OBJECT IDENTIFIER ::= { adsl2 5 } adsl2Scalar OBJECT IDENTIFIER ::= { adsl2 6 } adsl2Notifications OBJECT IDENTIFIER ::= { adsl2 0 } adsl2Conformance OBJECT IDENTIFIER ::= { adsl2 7 } ------------------------------------------------ adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 } adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 } ------------------------------------------------ adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 } adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 } adsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { adsl2Profile 3 } ------------------------------------------------ adsl2ScalarSC OBJECT IDENTIFIER ::= { adsl2Scalar 1 } ------------------------------------------------ ------------------------------------------------ -- adsl2LineTable -- ------------------------------------------------ adsl2LineTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2LineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner." ::= { adsl2Line 1 } adsl2LineEntry OBJECT-TYPE SYNTAX Adsl2LineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineTable contains configuration, commands, and status parameters of the ADSL2 line" INDEX { ifIndex } ::= { adsl2LineTable 1 } Adsl2LineEntry ::= SEQUENCE { adsl2LineCnfgTemplate SnmpAdminString, adsl2LineAlarmCnfgTemplate SnmpAdminString, adsl2LineCmndConfPmsf Adsl2ConfPmsForce, adsl2LineCmndConfLdsf Adsl2LineLdsf, adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult, adsl2LineCmndAutomodeColdStart TruthValue, adsl2LineStatusAtuTransSys Adsl2TransmissionModeType, adsl2LineStatusPwrMngState Adsl2PowerMngState, adsl2LineStatusInitResult Adsl2InitResult, adsl2LineStatusLastStateDs Adsl2LastTransmittedState, adsl2LineStatusLastStateUs Adsl2LastTransmittedState, adsl2LineStatusAtur Adsl2LineStatus, adsl2LineStatusAtuc Adsl2LineStatus, adsl2LineStatusLnAttenDs Unsigned32, adsl2LineStatusLnAttenUs Unsigned32, adsl2LineStatusSigAttenDs Unsigned32, adsl2LineStatusSigAttenUs Unsigned32, adsl2LineStatusSnrMarginDs Integer32, adsl2LineStatusSnrMarginUs Integer32, adsl2LineStatusAttainableRateDs Unsigned32, adsl2LineStatusAttainableRateUs Unsigned32, adsl2LineStatusActPsdDs Integer32, adsl2LineStatusActPsdUs Integer32, adsl2LineStatusActAtpDs Integer32, adsl2LineStatusActAtpUs Integer32 } adsl2LineCnfgTemplate OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (adsl2LineConfTemplateTable), which applies for this ADSL2 line. This object MUST be maintained in a persistent manner." REFERENCE "DSL Forum TR-90, paragraph 5.1.1" DEFVAL { "DEFVAL" } ::= { adsl2LineEntry 1 } adsl2LineAlarmCnfgTemplate OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line. This object MUST be maintained in a persistent manner." REFERENCE "DSL Forum TR-90, paragraph 5.1.1" DEFVAL { "DEFVAL" } ::= { adsl2LineEntry 2 } adsl2LineCmndConfPmsf OBJECT-TYPE SYNTAX Adsl2ConfPmsForce MAX-ACCESS read-write STATUS current DESCRIPTION "Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0(0), l0toL2(2), or l0orL2toL3(3). This object MUST be maintained in a persistent manner." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3" DEFVAL { l3toL0 } ::= { adsl2LineEntry 3 } adsl2LineCmndConfLdsf OBJECT-TYPE SYNTAX Adsl2LineLdsf MAX-ACCESS read-write STATUS current DESCRIPTION "Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU. This object MUST be maintained in a persistent manner. However, in case the operator forces loop diagnostics mode then the access node should reset the object (inhibit) when loop diagnostics mode procedures are completed." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.8" DEFVAL { inhibit } ::= { adsl2LineEntry 4 } adsl2LineCmndConfLdsfFailReason OBJECT-TYPE SYNTAX Adsl2LdsfResult MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. unsupported(4) - The NE or the line card doesn't support LDSF. cannotRun(5) - The NE cannot initiate the command, due to a nonspecific reason. aborted(6) - The Loop Diagnostics process aborted. failed(7) - The Loop Diagnostics process failed. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp(9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources." DEFVAL { none } ::= { adsl2LineEntry 5 } adsl2LineCmndAutomodeColdStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the adsl2LConfProfAtuTransSysEna object in the line configuration profile being used for the ADSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions. This object MUST be maintained in a persistent manner." REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10" DEFVAL { false } ::= { adsl2LineEntry 6 } adsl2LineStatusAtuTransSys OBJECT-TYPE SYNTAX Adsl2TransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU Transmission System (ATS) in use. It is coded in a bit-map representation with only a single bit set to '1' (the selected coding for the ADSL line). This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. A set of ADSL2 line transmission modes, with one bit per mode." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1" ::= { adsl2LineEntry 7 } adsl2LineStatusPwrMngState OBJECT-TYPE SYNTAX Adsl2PowerMngState MAX-ACCESS read-only STATUS current DESCRIPTION "The current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime). L1 - Low Power with reduced net data rate (G.992.2 only). L2 - Low Power with reduced net data rate (G.992.3 and G.992.4 only). L3 - No power. The various possible values are: l0(1), l1(2), l2(3), or l3(4)." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2" ::= { adsl2LineEntry 8 } adsl2LineStatusInitResult OBJECT-TYPE SYNTAX Adsl2InitResult MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), or otherCause(5)." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3" ::= { adsl2LineEntry 9 } adsl2LineStatusLastStateDs OBJECT-TYPE SYNTAX Adsl2LastTransmittedState MAX-ACCESS read-only STATUS current DESCRIPTION "The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.4" ::= { adsl2LineEntry 10 } adsl2LineStatusLastStateUs OBJECT-TYPE SYNTAX Adsl2LastTransmittedState MAX-ACCESS read-only STATUS current DESCRIPTION "The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.5" ::= { adsl2LineEntry 11 } adsl2LineStatusAtur OBJECT-TYPE SYNTAX Adsl2LineStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions." REFERENCE "ITU-T G.997.1, paragraph 7.1.1.2" ::= { adsl2LineEntry 12 } adsl2LineStatusAtuc OBJECT-TYPE SYNTAX Adsl2LineStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions." REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1" ::= { adsl2LineEntry 13 } adsl2LineStatusLnAttenDs OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6" ::= { adsl2LineEntry 14 } adsl2LineStatusLnAttenUs OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7" ::= { adsl2LineEntry 15 } adsl2LineStatusSigAttenDs OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8" ::= { adsl2LineEntry 16 } adsl2LineStatusSigAttenUs OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9" ::= { adsl2LineEntry 17 } adsl2LineStatusSnrMarginDs OBJECT-TYPE SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Downstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10" ::= { adsl2LineEntry 18 } adsl2LineStatusSnrMarginUs OBJECT-TYPE SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Upstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11" ::= { adsl2LineEntry 19 } adsl2LineStatusAttainableRateDs OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits/second" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bits/second." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12" ::= { adsl2LineEntry 20 } adsl2LineStatusAttainableRateUs OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits/second" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bits/second." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13" ::= { adsl2LineEntry 21 } adsl2LineStatusActPsdDs OBJECT-TYPE SYNTAX Integer32 (-900..0 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14" ::= { adsl2LineEntry 22 } adsl2LineStatusActPsdUs OBJECT-TYPE SYNTAX Integer32 (-900..0 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15" ::= { adsl2LineEntry 23 } adsl2LineStatusActAtpDs OBJECT-TYPE SYNTAX Integer32 (-310..310 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16" ::= { adsl2LineEntry 24 } adsl2LineStatusActAtpUs OBJECT-TYPE SYNTAX Integer32 (-310..310 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17" ::= { adsl2LineEntry 25 } ------------------------------------------------ -- adsl2ChannelStatusTable -- ------------------------------------------------ adsl2ChannelStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2ChannelStatusTable contains status parameters of the ADSL2 channel. This table contains live data from equipment." ::= { adsl2Status 1 } adsl2ChannelStatusEntry OBJECT-TYPE SYNTAX Adsl2ChannelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2ChannelStatusTable contains status parameters of the ADSL2 channel. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit." INDEX { ifIndex, adsl2ChStatusUnit } ::= { adsl2ChannelStatusTable 1 } Adsl2ChannelStatusEntry ::= SEQUENCE { adsl2ChStatusUnit Adsl2Unit, adsl2ChStatusChannelNum Unsigned32, adsl2ChStatusActDataRate Unsigned32, adsl2ChStatusPrevDataRate Unsigned32, adsl2ChStatusActDelay Unsigned32, adsl2ChStatusAtmStatus Adsl2ChAtmStatus, adsl2ChStatusPtmStatus Adsl2ChPtmStatus } adsl2ChStatusUnit OBJECT-TYPE SYNTAX Adsl2Unit MAX-ACCESS not-accessible STATUS current DESCRIPTION "The termination unit atuc(1) or atur(2)." ::= { adsl2ChannelStatusEntry 1 } adsl2ChStatusChannelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel." ::= { adsl2ChannelStatusEntry 2 } adsl2ChStatusActDataRate OBJECT-TYPE SYNTAX Unsigned32(0..200000000) UNITS "bits/second" MAX-ACCESS read-only STATUS current DESCRIPTION "The actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bits/second." REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1" ::= { adsl2ChannelStatusEntry 3 } adsl2ChStatusPrevDataRate OBJECT-TYPE SYNTAX Unsigned32(0..200000000) UNITS "bits/second" MAX-ACCESS read-only STATUS current DESCRIPTION "The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding transitions between L0 state and L1 or L2 states. The data rate is coded in bits/second." REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2" ::= { adsl2ChannelStatusEntry 4 } adsl2ChStatusActDelay OBJECT-TYPE SYNTAX Unsigned32(0..8176) UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (rounded to the nearest ms)." REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3" ::= { adsl2ChannelStatusEntry 5 } adsl2ChStatusAtmStatus OBJECT-TYPE SYNTAX Adsl2ChAtmStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), noCellDelineation(1), or lossOfCellDelineation(2). In the case where the channel is not an ATM Data Path, the object is set to '0'." REFERENCE "ITU-T G.997.1, paragraph 7.1.4" ::= { adsl2ChannelStatusEntry 6 } adsl2ChStatusPtmStatus OBJECT-TYPE SYNTAX Adsl2ChPtmStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), or outOfSync(1). In the case where the channel is not a PTM Data Path, the object is set to '0'." REFERENCE "ITU-T G.997.1, paragraph 7.1.5" ::= { adsl2ChannelStatusEntry 7 } ------------------------------------------------ -- Scalars that relate to the adsl2SCStatusTable. ------------------------------------------------ adsl2ScalarSCMaxInterfaces OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value determines the upper size of adsl2SCStatusTable. The maximum number of entries in adsl2SCStatusTable is equal to two times the value of this attribute." ::= { adsl2ScalarSC 1 } adsl2ScalarSCAvailInterfaces OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value determines the amount of space that is currently available in adsl2SCStatusTable. The number of entries available in adsl2SCStatusTable is equal to two times the value of this attribute." ::= { adsl2ScalarSC 2 } ------------------------------------------------ -- adsl2SCStatusTable -- ------------------------------------------------ adsl2SCStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2SCStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2)." ::= { adsl2Status 2 } adsl2SCStatusEntry OBJECT-TYPE SYNTAX Adsl2SCStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table Adsl2SCStatusEntry contains status parameters of the ADSL2 sub-carriers. The index of this table is an interface index where the interface has an ifType of adsl2plus(238)." INDEX { ifIndex, adsl2SCStatusDirection } ::= { adsl2SCStatusTable 1 } Adsl2SCStatusEntry ::= SEQUENCE { adsl2SCStatusDirection Adsl2Direction, adsl2SCStatusMtime Unsigned32, adsl2SCStatusSnr OCTET STRING, adsl2SCStatusBitsAlloc OCTET STRING, adsl2SCStatusGainAlloc OCTET STRING, adsl2SCStatusTssi Adsl2Tssi, adsl2SCStatusLinScale Unsigned32, adsl2SCStatusLinReal OCTET STRING, adsl2SCStatusLinImg OCTET STRING, adsl2SCStatusLogMt Unsigned32, adsl2SCStatusLog OCTET STRING, adsl2SCStatusQlnMt Unsigned32, adsl2SCStatusQln OCTET STRING, adsl2SCStatusLnAtten Unsigned32, adsl2SCStatusSigAtten Unsigned32, adsl2SCStatusSnrMargin Integer32, adsl2SCStatusAttainableRate Unsigned32, adsl2SCStatusActAtp Integer32, adsl2SCStatusRowStatus RowStatus } adsl2SCStatusDirection OBJECT-TYPE SYNTAX Adsl2Direction MAX-ACCESS not-accessible STATUS current DESCRIPTION "The direction of the sub-carrier is either upstream or downstream." ::= { adsl2SCStatusEntry 1 } adsl2SCStatusMtime OBJECT-TYPE SYNTAX Unsigned32 UNITS "symbols" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds) and paragraph 7.5.1.20.3 (SNRMTus)" ::= { adsl2SCStatusEntry 2 } adsl2SCStatusSnr OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds) and paragraph 7.5.1.20.4 (SNRpsus)" ::= { adsl2SCStatusEntry 3 } adsl2SCStatusBitsAlloc OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) UNITS "bits" MAX-ACCESS read-only STATUS current DESCRIPTION "The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds) and paragraph 7.5.1.21.2 (BITSpsus)" ::= { adsl2SCStatusEntry 4 } adsl2SCStatusGainAlloc OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds) and paragraph 7.5.1.21.4 (GAINSpsus)" ::= { adsl2SCStatusEntry 5 } adsl2SCStatusTssi OBJECT-TYPE SYNTAX Adsl2Tssi MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of the breakpoint. Third octet - The shaping parameter at the breakpoint. Subcarrier index is an unsigned number in the range 1 to either NSCds (downstream direction) or NSCus (upstream direction). The shaping parameter value is in the range 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.5 (TSSpsds) and paragraph 7.5.1.21.6 (TSSpsus)" ::= { adsl2SCStatusEntry 6 } adsl2SCStatusLinScale OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.1 (HLINSCds) and paragraph 7.5.1.18.5 (HLINSCus)" ::= { adsl2SCStatusEntry 7 } adsl2SCStatusLinReal OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real component [referred to here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) and b(i) [provided by the Adsl2SubcarrierLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds) and paragraph 7.5.1.18.6 (HLINpsds)" ::= { adsl2SCStatusEntry 8 } adsl2SCStatusLinImg OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the imaginary component [referred to here as b(i)] of Hlin(f = i*Df) value for a particular sub- carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) [provided by the Adsl2SubcarrierLinReal object] and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds) and paragraph 7.5.1.18.6 (HLINpsds)" ::= { adsl2SCStatusEntry 9 } adsl2SCStatusLogMt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.3 (HLOGMTds) and paragraph 7.5.1.18.7 (HLOGMTus)" ::= { adsl2SCStatusEntry 10 } adsl2SCStatusLog OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..1024)) MAX-ACCESS read-only STATUS current DESCRIPTION "An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.4 (HLOGpsds) and paragraph 7.5.1.18.8 (HLOGpsus)" ::= { adsl2SCStatusEntry 11 } adsl2SCStatusQlnMt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization " REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.1 (QLNMTds) and paragraph 7.5.1.19.3 (QLNMTus)" ::= { adsl2SCStatusEntry 12 } adsl2SCStatusQln OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) UNITS "dBm/Hz" MAX-ACCESS read-only STATUS current DESCRIPTION "An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds) and paragraph 7.5.1.19.4 (QLNpsus)" ::= { adsl2SCStatusEntry 13 } adsl2SCStatusLnAtten OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6 (LATNds) and paragraph 7.5.1.7 (LATNus)" ::= { adsl2SCStatusEntry 14 } adsl2SCStatusSigAtten OBJECT-TYPE SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8 (SATNds) and paragraph 7.5.1.9 (SATNus)" ::= { adsl2SCStatusEntry 15 } adsl2SCStatusSnrMargin OBJECT-TYPE SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds) and paragraph 7.5.1.11 (SNRMus)" ::= { adsl2SCStatusEntry 16 } adsl2SCStatusAttainableRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits/second" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream direction) or by the ATU-R transmitter and ATU-C receiver (when referring to upstream direction). Value is coded in bits/second. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds) and paragraph 7.5.1.13 (ATTNDRus)" ::= { adsl2SCStatusEntry 17 } adsl2SCStatusActAtp OBJECT-TYPE SYNTAX Integer32 UNITS "0.1 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds) and paragraph 7.5.1.17 (ACTATPus)" ::= { adsl2SCStatusEntry 18 } adsl2SCStatusRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row Status. The manager may create and delete rows of this table. Please see the description of adsl2SCStatusTable above for more details." ::= { adsl2SCStatusEntry 19 } ------------------------------------------------ -- adsl2LineInventoryTable -- ------------------------------------------------ adsl2LineInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2LineInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineInventoryTable contains inventory of the ADSL2 units." ::= { adsl2Inventory 1 } adsl2LineInventoryEntry OBJECT-TYPE SYNTAX Adsl2LineInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineInventoryTable contains inventory of the ADSL2 units. The index of this table is an interface index where the interface has an ifType of adsl2plus(238)." INDEX { ifIndex, adsl2LInvUnit } ::= { adsl2LineInventoryTable 1 } Adsl2LineInventoryEntry ::= SEQUENCE { adsl2LInvUnit Adsl2Unit, adsl2LInvG994VendorId OCTET STRING, adsl2LInvSystemVendorId OCTET STRING, adsl2LInvVersionNumber OCTET STRING, adsl2LInvSerialNumber OCTET STRING, adsl2LInvSelfTestResult Unsigned32, adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType } adsl2LInvUnit OBJECT-TYPE SYNTAX Adsl2Unit MAX-ACCESS not-accessible STATUS current DESCRIPTION "The termination unit atuc(1) or atur(2)." ::= { adsl2LineInventoryEntry 1 } adsl2LInvG994VendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 2 } adsl2LInvSystemVendorId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with the same format as used for Adsl2InvG994VendorId." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 3 } adsl2LInvVersionNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU version number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 4 } adsl2LInvSerialNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU serial number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It is vendor-specific information. It consists of up to 32 ASCII characters." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 5 } adsl2LInvSelfTestResult OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 6 } adsl2LInvTransmissionCapabilities OBJECT-TYPE SYNTAX Adsl2TransmissionModeType MAX-ACCESS read-only STATUS current DESCRIPTION "The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of ADSL2 line transmission modes, with one bit per mode." REFERENCE "ITU-T G.997.1, paragraph 7.4" ::= { adsl2LineInventoryEntry 7 } ------------------------------------------------ -- adsl2LineConfTemplateTable -- ------------------------------------------------ adsl2LineConfTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineConfTemplateTable contains ADSL2 line configuration templates. Entries in this table MUST be maintained in a persistent manner." ::= { adsl2ProfileLine 1 } adsl2LineConfTemplateEntry OBJECT-TYPE SYNTAX Adsl2LineConfTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineConfTemplateTable contains the ADSL2 line configuration template. A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document." INDEX { adsl2LConfTempTemplateName } ::= { adsl2LineConfTemplateTable 1 } Adsl2LineConfTemplateEntry ::= SEQUENCE { adsl2LConfTempTemplateName SnmpAdminString, adsl2LConfTempLineProfile SnmpAdminString, adsl2LConfTempChan1ConfProfile SnmpAdminString, adsl2LConfTempChan1RaRatioDs Unsigned32, adsl2LConfTempChan1RaRatioUs Unsigned32, adsl2LConfTempChan2ConfProfile SnmpAdminString, adsl2LConfTempChan2RaRatioDs Unsigned32, adsl2LConfTempChan2RaRatioUs Unsigned32, adsl2LConfTempChan3ConfProfile SnmpAdminString, adsl2LConfTempChan3RaRatioDs Unsigned32, adsl2LConfTempChan3RaRatioUs Unsigned32, adsl2LConfTempChan4ConfProfile SnmpAdminString, adsl2LConfTempChan4RaRatioDs Unsigned32, adsl2LConfTempChan4RaRatioUs Unsigned32, adsl2LConfTempRowStatus RowStatus } adsl2LConfTempTemplateName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a row in this table." REFERENCE "DSL Forum TR-90, paragraph 5.1.4" ::= { adsl2LineConfTemplateEntry 1 } adsl2LConfTempLineProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (adsl2LineConfProfTable), which applies for this ADSL2 line." REFERENCE "DSL Forum TR-90, paragraph 5.1.4" DEFVAL { "DEFVAL" } ::= { adsl2LineConfTemplateEntry 2 } adsl2LConfTempChan1ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChConfProfileTable table." DEFVAL { "DEFVAL" } ::= { adsl2LineConfTemplateEntry 3 } adsl2LConfTempChan1RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 100 } ::= { adsl2LineConfTemplateEntry 4 } adsl2LConfTempChan1RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 100 } ::= { adsl2LineConfTemplateEntry 5 } adsl2LConfTempChan2ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if adsl2LConfTempChan3ConfProfile contains a zero-length string." DEFVAL { "" } ::= { adsl2LineConfTemplateEntry 6 } adsl2LConfTempChan2RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 7 } adsl2LConfTempChan2RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 8 } adsl2LConfTempChan3ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #3. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if adsl2LConfTempChan4ConfProfile contains a zero-length string. This object may be set to a non-zero-length string only if adsl2LConfTempChan2ConfProfile contains a non-zero-length string." DEFVAL { "" } ::= { adsl2LineConfTemplateEntry 9 } adsl2LConfTempChan3RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 10 } adsl2LConfTempChan3RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 11 } adsl2LConfTempChan4ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #4. If the channel is unused, then the object is set to a zero-length string. This object may be set to a non-zero-length string only if adsl2LConfTempChan3ConfProfile contains a non-zero-length string." DEFVAL { "" } ::= { adsl2LineConfTemplateEntry 12 } adsl2LConfTempChan4RaRatioDs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 13 } adsl2LConfTempChan4RaRatioUs OBJECT-TYPE SYNTAX Unsigned32(0..100) UNITS "percent" MAX-ACCESS read-create STATUS current DESCRIPTION "Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%." REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" DEFVAL { 0 } ::= { adsl2LineConfTemplateEntry 14 } adsl2LConfTempRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated lines." ::= { adsl2LineConfTemplateEntry 15 } ------------------------------------------ -- adsl2LineConfProfTable -- ------------------------------------------ adsl2LineConfProfTable OBJECT-TYPE SYNTAX SEQUENCE OF Adsl2LineConfProfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineConfProfTable contains ADSL2 line profile configuration. Entries in this table MUST be maintained in a persistent manner." ::= { adsl2ProfileLine 2 } adsl2LineConfProfEntry OBJECT-TYPE SYNTAX Adsl2LineConfProfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table adsl2LineConfProfTable contains ADSL2 line profile configuration. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document." INDEX { adsl2LConfProfProfileName } ::= { adsl2LineConfProfTable 1 } Adsl2LineConfProfEntry ::= SEQUENCE { adsl2LConfProfProfileName SnmpAdminString, adsl2LConfProfScMaskDs Adsl2ScMaskDs, adsl2LConfProfScMaskUs Adsl2ScMaskUs, adsl2LConfProfRfiBandsDs Adsl2RfiDs, adsl2LConfProfRaModeDs Adsl2RaMode, adsl2LConfProfRaModeUs Adsl2RaMode, adsl2LConfProfRaUsNrmDs Unsigned32, adsl2LConfProfRaUsNrmUs Unsigned32, adsl2LConfProfRaUsTimeDs Unsigned32, adsl2LConfProfRaUsTimeUs Unsigned32, adsl2LConfProfRaDsNrmsDs Unsigned32, adsl2LConfProfRaDsNrmsUs Unsigned32, adsl2LConfProfRaDsTimeDs Unsigned32, adsl2LConfProfRaDsTimeUs Unsigned32, adsl2LConfProfTargetSnrmDs Unsigned32, adsl2LConfProfTargetSnrmUs Unsigned32, adsl2LConfProfMaxSnrmDs Unsigned32, adsl2LConfProfMaxSnrmUs Unsigned32, adsl2LConfProfMinSnrmDs Unsigned32, adsl2LConfProfMinSnrmUs Unsigned32, adsl2LConfProfMsgMinUs Unsigned32, adsl2LConfProfMsgMinDs Unsigned32, adsl2LConfProfAtuTransSysEna Adsl2TransmissionModeType, adsl2LConfProfPmMode Adsl2LConfProfPmMode, adsl2LConfProfL0Time Unsigned32, adsl2LConfProfL2Time Unsigned32, adsl2LConfProfL2Atpr Unsigned32, adsl2LConfProfL2Atprt Unsigned32, adsl2LConfProfRowStatus RowStatus } adsl2LConfProfProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a row in this table." ::= { adsl2LineConfProfEntry 1 } adsl2LConfProfScMaskDs OBJECT-TYPE SYNTAX Adsl2ScMaskDs MAX-ACCESS read-create STATUS current DESCRIPTION "Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds < i <= 512) should be set to '1'." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.6" ::= { adsl2LineConfProfEntry 2 } adsl2LConfProfScMaskUs OBJECT-TYPE SYNTAX Adsl2ScMaskUs MAX-ACCESS read-create STATUS current DESCRIPTION "Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'." REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.7" ::= { adsl2LineConfProfEntry 3 } adsl2LConfProfRfiBandsDs OBJECT-TYPE SYNTAX Adsl2RfiDs MAX-ACCESS read-create STATUS current DESCRIPTION "The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is part of a notch filter, and if set to '0', the respective sub-carrier is not part of a notch filter. This information complements the specification provided by adsl2LConfProfPsdMaskDs. Note that if NSCds < 512, all bits i (NSCds