-- extracted from draft-ietf-bfd-mib-00.txt -- at Thu Jul 8 06:21:49 2004 BFD-DRAFT-00-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Counter32, Counter64, NOTIFICATION-TYPE, mib-2 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC InetAddress, InetAddressType FROM INET-ADDRESS-MIB ; bfdMIB MODULE-IDENTITY LAST-UPDATED "200401221200Z" -- 22 January 2004 12:00:00 EST ORGANIZATION "IETF" CONTACT-INFO " Zafar Ali Cisco Systems, Inc. Email: zali@cisco.com Thomas D. Nadeau Cisco Systems, Inc. Email: tnadeau@cisco.com " DESCRIPTION "Bidirectional Forwarding Management Information Base." -- Revision history. REVISION "200401221200Z" -- 22 January 2004 12:00:00 EST DESCRIPTION "Initial version." ::= { mib-2 999 } -- To be assigned by IANA. -- Top level components of this MIB module. bfdNotifications OBJECT IDENTIFIER ::= { bfdMIB 0 } bfdObjects OBJECT IDENTIFIER ::= { bfdMIB 1 } bfdConformance OBJECT IDENTIFIER ::= { bfdMIB 3 } bfdScalarObjects OBJECT IDENTIFIER ::= { bfdObjects 1 } -- Textual Conventions BfdSessIndexTC ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An index used to uniquely identify BFD sessions." SYNTAX Unsigned32 (1..4294967295) BfdInterval ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The BFD interval delay in microseconds." SYNTAX Unsigned32 (1..4294967295) BfdDiag ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A common BFD diagnostic code." SYNTAX INTEGER { noDiagnostic(1), controlDetectionTimeExpired(2), echoFunctionFailed(3), neighborSignaledSessionDown(4), forwardingPlaneReset(5), pathDown(6), concatenatedPathDown(7), administrativelyDown(8) } -- BFD General Variables -- These parameters apply globally to the Router's -- BFD Process. bfdAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The global administrative status of BFD in this router. The value 'enabled' denotes that the BFD Process is active on at least one interface; 'disabled' disables it on all interfaces." DEFVAL { enabled } ::= { bfdScalarObjects 1 } bfdOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of BFD on this router." ::= { bfdScalarObjects 2 } bfdVersionNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current version number of the BFD protocol." REFERENCE " BFD Version 0 (draft-katz-ward-bfd-04.txt)" DEFVAL { 0 } ::= { bfdScalarObjects 3 } -- BFD Session Table -- The BFD Session Table specifies BFD session specific -- information. bfdSessTable OBJECT-TYPE SYNTAX SEQUENCE OF BfdSessEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BFD Session Table describes the BFD sessions." REFERENCE "BFD Version 0 (draft-katz-ward-bfd-04.txt)" ::= { bfdObjects 2 } bfdSessEntry OBJECT-TYPE SYNTAX BfdSessEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BFD Session Entry describes BFD session." INDEX { bfdSessIndex } ::= { bfdSessTable 1 } BfdSessEntry ::= SEQUENCE { bfdSessIndex BfdSessIndexTC, bfdSessApplicationId Unsigned32, bfdSessDiscriminator Unsigned32, bfdSessLocalDiscr Unsigned32, bfdSessRemoteDiscr Unsigned32, bfdSessState INTEGER, bfdSessRemoteHeardFlag TruthValue, bfdSessDiag Unsigned32, bfdSessOperMode INTEGER, bfdSessDemandModeDesiredFlag TruthValue, bfdSessEchoFuncModeDesiredFlag TruthValue, bfdSessEchoFuncFlag INTEGER, bfdSessAddrType InetAddressType, bfdSessAddr InetAddress, bfdSessDesiredMinTxInterval BfdInterval, bfdSessDesiredMinRxInterval BfdInterval, bfdSessDesiredMinEchoRxInterval BfdInterval, bfdSessDetectMult BfdInterval, bfdSessStorType StorageType, bfdSessRowStatus RowStatus } bfdSessIndex OBJECT-TYPE SYNTAX BfdSessIndexTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains an index used to represent a unique BFD session on this device." ::= { bfdSessEntry 1 } bfdSessApplicationId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an index used to indicate an local application which owns or maintains this BFD session. For instance, the VPN process may maintain a subset of the total number of BFD sessions. This application ID provides a convienent way to segretate sessions by the applications which maintain them." ::= { bfdSessEntry 2 } bfdSessDiscriminator OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the local discriminator for this BFD session, used to uniquely identify it." ::= { bfdSessEntry 3 } bfdSessLocalDiscr OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the local discriminator for this BFD session, used to uniquely identify it." ::= { bfdSessEntry 4 } bfdSessRemoteDiscr OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the discriminator chosen by the remote system local discriminator for this BFD session." ::= { bfdSessEntry 5 } bfdSessState OBJECT-TYPE SYNTAX INTEGER { init(1), up(2), failing(3), down(4), adminDown(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The perceived state of the BFD session." ::= { bfdSessEntry 6 } bfdSessRemoteHeardFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies status of BFD packet reception from the remote system. Specifically, it is set to true(1) if the local system is actively receiving BFD packets from the remote system, and is set to false(0) if the local system has not received BFD packets recently (within the detection time) or if the local system is attempting to tear down the BFD session." ::= { bfdSessEntry 7 } bfdSessDiag OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "A diagnostic code specifying the local system's reason for the last transition of the session from up(1) to some other state." ::= { bfdSessEntry 8 } bfdSessOperMode OBJECT-TYPE SYNTAX INTEGER { asyncModeWEchoFun(1), asynchModeWOEchoFun(2), demandModeWEchoFunction(3), demandModeWOEchoFunction(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies current operating mode that BFD session is operating in. A value of AsyncModeWEchoFun(1) ... A value of AsynchModeWOEchoFun(2) ... A value of DemandModeWEchoFunction(3) ... A value of DemandModeWOEchoFunction(4) ... " ::= { bfdSessEntry 9 } bfdSessDemandModeDesiredFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates that the local system's desire to use Demand mode. Specifically, it is set to true(1) if the local system wishes to use Demand mode or false(0) if not" DEFVAL { false } ::= { bfdSessEntry 10 } bfdSessEchoFuncModeDesiredFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates that the local system's desire to use Echo mode. Specifically, it is set to true(1) if the local system wishes to use Echo mode or false(0) if not" DEFVAL { false } ::= { bfdSessEntry 11 } bfdSessEchoFuncFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative status of Echo function for this BFD session. The value 'enabled' denotes that the Echo function is enabled for this session; 'disabled' disables Echo function for this session." ::= { bfdSessEntry 12 } bfdSessAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies IP address of the interface associated with this BFD session. Only values unknown(0), ipv4(1) or ipv6(2) have to be supported. A value of unknown(0) is allowed only when the outgoing interface is of type point-to-point, or when the BFD session is not associated with a specific interface. If any other unsupported values are attempted in a set operation, the agent MUST return an inconsistentValue error. " ::= { bfdSessEntry 13 } bfdSessAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies IP address of the interface associated with this BFD session. It can also be used to enabled BFD on a specific interface. The value is set to zero when BFD session is not associated with a specific interface. " ::= { bfdSessEntry 14 } bfdSessDesiredMinTxInterval OBJECT-TYPE SYNTAX BfdInterval MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets." ::= { bfdSessEntry 15 } bfdSessDesiredMinRxInterval OBJECT-TYPE SYNTAX BfdInterval MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the minimum interval, in microseconds, between received BFD Control packets the local system is capable of supporting." ::= { bfdSessEntry 16 } bfdSessDesiredMinEchoRxInterval OBJECT-TYPE SYNTAX BfdInterval MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting." ::= { bfdSessEntry 17 } bfdSessDetectMult OBJECT-TYPE SYNTAX BfdInterval MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the Detect time multiplier." ::= { bfdSessEntry 18 } bfdSessStorType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." ::= { bfdSessEntry 19 } bfdSessRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. When a row in this table has a row in the active(1) state, no objects in this row can be modified except the bfdSessRowStatus and bfdSessStorageType." ::= { bfdSessEntry 20 } -- BFD Session Performance Table bfdSessPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF BfdSessPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies BFD Session performance counters." ::= { bfdObjects 3 } bfdSessPerfEntry OBJECT-TYPE SYNTAX BfdSessPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by a BFD-enabled node for every BFD Session. bfdCounterDiscontinuityTime is used to indicate potential discontinuity for all counter objects in this table." AUGMENTS { bfdSessEntry } ::= { bfdSessPerfTable 1 } BfdSessPerfEntry ::= SEQUENCE { bfdSessPerfPktIn Counter32, bfdSessPerfPktOut Counter32, bfdSessPerfBadDiscrim Counter32, bfdSessPerfLastSessDownTime TimeStamp, bfdSessPerfLastCommLostDiag BfdDiag, bfdSessPerfSessDownCount Counter32, bfdSessPerfDiscTime TimeStamp, -- High Capacity Counters bfdSessPerfPktInHC Counter64, bfdSessPerfPktOutHC Counter64, bfdSessPerfBadDiscrimHC Counter64 } -- Ed Note: should we add per-diag code counts here, bfdSessPerfPktIn OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of BFD messages received for this BFD session." ::= { bfdSessPerfEntry 1 } bfdSessPerfPktOut OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of BFD messages sent for this BFD session." ::= { bfdSessPerfEntry 2 } bfdSessPerfBadDiscrim OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of BFD messages received with a bad local Discriminator value for this BFD session." ::= { bfdSessPerfEntry 3 } bfdSessPerfLastSessDownTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which the last time communication was lost with the neighbor. If no such down event exist this object contains a zero value." ::= { bfdSessPerfEntry 4 } bfdSessPerfLastCommLostDiag OBJECT-TYPE SYNTAX BfdDiag MAX-ACCESS read-only STATUS current DESCRIPTION "The BFD diag code for the last time communication was lost with the neighbor. If no such down event exist this object contains a zero value." ::= { bfdSessPerfEntry 5 } bfdSessPerfSessDownCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this session has gone into the down state since the router last rebooted." ::= { bfdSessPerfEntry 6 } bfdSessPerfDiscTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of the session counters suffered a discontinuity. The relevant counters are the specific instances associated with this BFD sesion of any Counter32 object contained in the BfdSessPerfTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value." ::= { bfdSessPerfEntry 7 } bfdSessPerfPktInHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of total number of BFD messages received for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktInHC is supported according to the rules spelled out in RFC2863." ::= { bfdSessPerfEntry 8 } bfdSessPerfPktOutHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of total number of BFD messages transmitted for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktOutHC is supported according to the rules spelled out in RFC2863." ::= { bfdSessPerfEntry 9 } bfdSessPerfBadDiscrimHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of total number of BFD messages received with a bad local Discriminator value for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfBadDiscrimHC if bfdSessPerfBadDiscrimHC is supported according to the rules spelled out in RFC2863." ::= { bfdSessPerfEntry 10 } -- BFD Sess Mapping Table bfdSessMapTable OBJECT-TYPE SYNTAX SEQUENCE OF BfdSessMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BFD Session Map Table maps the complex indexing of the BFD sessions to the flat BFDIndex used in the BfdSessionTable. Implementors need to be aware that if the value of the bfdSessAddr (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3. " REFERENCE "BFD Version 0 (draft-katz-ward-bfd-04.txt)" ::= { bfdObjects 4 } bfdSessMapEntry OBJECT-TYPE SYNTAX BfdSessMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BFD Session Entry describes BFD session that is mapped to this index. Implementors need to be aware that if the value of the bfdSessAddr has more that 111 octets, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3" INDEX { bfdSessApplicationId, bfdSessDiscriminator, bfdSessAddrType, bfdSessAddr } ::= { bfdSessMapTable 1 } BfdSessMapEntry ::= SEQUENCE { bfdSessMapBfdIndex BfdSessIndexTC } bfdSessMapBfdIndex OBJECT-TYPE SYNTAX BfdSessIndexTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the BfdIndex refered to by the indexes of this row. In essence, a mapping is provided between these indexes and the BfdSessTable." ::= { bfdSessMapEntry 1 } -- Notification Configuration bfdSessNotificationsEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of bfdSessUp and bfdSessDown notifications; otherwise these notifications are not emitted." REFERENCE "See also RFC3413 for explanation that notifications are under the ultimate control of the MIB modules in this document." DEFVAL { false } ::= { bfdScalarObjects 4 } bfdSessUp NOTIFICATION-TYPE OBJECTS { bfdSessDiag, -- low range value bfdSessDiag -- high range value } STATUS current DESCRIPTION "This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the up(2) state from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: up(1)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of sessions have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical." ::= { bfdNotifications 1 } bfdSessDown NOTIFICATION-TYPE OBJECTS { bfdSessDiag, -- low range value bfdSessDiag -- high range value } STATUS current DESCRIPTION "This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the down(4) or adminDown(5) states from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: down(4) or adminDown(5)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of sessions have transitioned into the down(4) or adminDown(5) states at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical." ::= { bfdNotifications 2 } -- Module compliance. bfdGroups OBJECT IDENTIFIER ::= { bfdConformance 1 } bfdCompliances OBJECT IDENTIFIER ::= { bfdConformance 2 } -- Compliance requirement for fully compliant implementations. bfdModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that provide full support for BFD-MIB. Such devices can then be monitored and also be configured using this MIB module." MODULE -- This module. MANDATORY-GROUPS { bfdSessionGroup, bfdSessionPerfGroup, bfdSessionPerfHCGroup, bfdNotificationGroup } GROUP bfdSessionPerfHCGroup DESCRIPTION "This group is mandatory for those bfdPerfTable entries for which any of the objects bfdSessPerfPktInHC, bfdSessPerfPktOutHC, or bfdSessPerfBadDiscrimHC wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP bfdNotificationGroup DESCRIPTION "This group is only mandatory for those implementations which can efficiently implement the notifications contained in this group." OBJECT bfdSessAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support is required." OBJECT bfdSessAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation is only required to support unknown(0), ipv4(1) and ipv6(2) sizes." ::= { bfdCompliances 1 } -- Read-Only compliance TBD... -- Units of conformance. bfdSessionGroup OBJECT-GROUP OBJECTS { bfdSessNotificationsEnable, bfdAdminStatus, bfdOperStatus, bfdVersionNumber, bfdSessApplicationId, bfdSessDiscriminator, bfdSessAddrType, bfdSessAddr, bfdSessLocalDiscr, bfdSessRemoteDiscr, bfdSessState, bfdSessRemoteHeardFlag, bfdSessDiag, bfdSessOperMode, bfdSessDemandModeDesiredFlag, bfdSessEchoFuncFlag, bfdSessEchoFuncModeDesiredFlag, bfdSessDesiredMinTxInterval, bfdSessDesiredMinRxInterval, bfdSessDesiredMinEchoRxInterval, bfdSessDetectMult, bfdSessStorType, bfdSessRowStatus, bfdSessMapBfdIndex } STATUS current DESCRIPTION "Collection of objects needed for BFD sessions." ::= { bfdGroups 1 } bfdSessionPerfGroup OBJECT-GROUP OBJECTS { bfdSessPerfPktIn, bfdSessPerfPktOut, bfdSessPerfBadDiscrim, bfdSessPerfLastSessDownTime, bfdSessPerfLastCommLostDiag, bfdSessPerfSessDownCount, bfdSessPerfDiscTime } STATUS current DESCRIPTION "Collection of objects needed to monitor the performance of BFD sessions." ::= { bfdGroups 2 } bfdSessionPerfHCGroup OBJECT-GROUP OBJECTS { bfdSessPerfPktInHC, bfdSessPerfPktOutHC, bfdSessPerfBadDiscrimHC } STATUS current DESCRIPTION "Collection of objects needed to monitor the performance of BFD sessions for which the values of bfdSessPerfPktIn, bfdSessPerfPktOut, or bfdSessPerfBadDiscrim wrap around too quickly." ::= { bfdGroups 3 } bfdNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { bfdSessUp, bfdSessDown } STATUS current DESCRIPTION "Set of notifications implemented in this module." ::= { bfdGroups 4 } END -- -- Copyright (C) The Internet Society (2003). All Rights Reserved. -- -- This document and translations of it may be copied and furnished -- to others, and derivative works that comment on or otherwise -- explain it or assist in its implementation may be prepared, -- copied, published and distributed, in whole or in part, without -- restriction of any kind, provided that the above copyright notice -- and this paragraph are included on all such copies and derivative -- works. However, this document itself may not be modified in any -- way, such as by removing the copyright notice or references to the -- Internet Society or other Internet organizations, except as needed -- for the purpose of developing Internet standards in which case -- the procedures for copyrights defined in the Internet Standards -- process must be followed, or as required to translate it into -- languages other than English. -- -- The limited permissions granted above are perpetual and will not -- be revoked by the Internet Society or its successors or assigns. -- This document and the information contained herein is provided on -- an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR -- IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF -- THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. --