-- extracted from draft-ietf-disman-remops-mib-v2-02.txt -- at Fri Jun 18 06:20:51 2004 DISMAN-NSLOOKUP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, mib-2, Integer32 FROM SNMPv2-SMI -- RFC2578 RowStatus FROM SNMPv2-TC -- RFC2579 MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- RFC2580 SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC3411 InetAddressType, InetAddress FROM INET-ADDRESS-MIB; -- RFC3291 lookupMIB MODULE-IDENTITY LAST-UPDATED "200402111111Z" -- 11 February 2004 ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO "Juergen Quittek NEC Europe Ltd. Network Laboratories Kurfuersten-Anlage 36 69115 Heidelberg Germany Phone: +49 6221 90511-15 Email: quittek@ccrle.nec.de" DESCRIPTION "The Lookup MIB (DISMAN-NSLOOKUP-MIB) enables determination of either the name(s) corresponding to a host address or of the address(es) associated with a host name at a remote host." -- Revision history REVISION "200009210000Z" -- 21 September 2000 DESCRIPTION "Initial version, published as RFC 2925." REVISION "200402111111Z" -- 11 February 2004 DESCRIPTION "Updated version, published as RFC XXXX. - replaced references to RFC 2575 by RFC 3415 - replaced references to RFC 2571 by RFC 3411 - replaced references to RFC 2851 by RFC 3291 - added value enabled(1) to SYNTAX clause of lookupCtlOperStatus" ::= { mib-2 82 } -- Top level structure of the MIB lookupObjects OBJECT IDENTIFIER ::= { lookupMIB 1 } lookupConformance OBJECT IDENTIFIER ::= { lookupMIB 2 } -- Simple Object Definitions lookupMaxConcurrentRequests OBJECT-TYPE SYNTAX Unsigned32 UNITS "requests" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of concurrent active lookup requests that are allowed within an agent implementation. A value of 0 for this object implies that there is no limit for the number of concurrent active requests in effect. The limit applies only to new requests being activated. When a new value is set, the agent will continue processing all the requests already active, even if their number exceed the limit just imposed." DEFVAL { 10 } ::= { lookupObjects 1 } lookupPurgeTime OBJECT-TYPE SYNTAX Unsigned32 (0..86400) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time to wait before automatically deleting an entry in the lookupCtlTable and any dependent lookupResultsTable entries after the lookup operation represented by an lookupCtlEntry has completed. An lookupCtEntry is considered complete when its lookupCtlOperStatus object has a value of completed(3). A value of 0 indicates that automatic deletion of entries is disabled." DEFVAL { 900 } -- 15 minutes as default ::= { lookupObjects 2 } -- Lookup Control Table lookupCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF LookupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Lookup Control Table for providing the capability of performing a lookup operation, gethostbyname or gethostbyaddr, from a remote host." ::= { lookupObjects 3 } lookupCtlEntry OBJECT-TYPE SYNTAX LookupCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the lookupCtlTable. A lookupCtlEntry is initially indexed by lookupCtlOwnerIndex, which is of type SnmpAdminString, a textual convention that allows for use of the SNMPv3 View-Based Access Control Model (RFC 3415, VACM) and also allows an management application to identify its entries. The second index element, lookupCtlOperationName, enables the same lookupCtlOwnerIndex entity to have multiple outstanding requests. The value of lookupCtlTargetAddressType determines which lookup function to perform. Specification of dns(16) as the value of this index implies that the gethostbyname function should be performed to determine the numeric addresses associated with a symbolic name via lookupResultsTable entries. Use of a value of either ipv4(1) or ipv6(2) implies that the gethostbyaddr function should be performed to determine the symbolic name(s) associated with a numeric address at a remote host." INDEX { lookupCtlOwnerIndex, lookupCtlOperationName } ::= { lookupCtlTable 1 } LookupCtlEntry ::= SEQUENCE { lookupCtlOwnerIndex SnmpAdminString, lookupCtlOperationName SnmpAdminString, lookupCtlTargetAddressType InetAddressType, lookupCtlTargetAddress InetAddress, lookupCtlOperStatus INTEGER, lookupCtlTime Unsigned32, lookupCtlRc Integer32, lookupCtlRowStatus RowStatus } lookupCtlOwnerIndex OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. When used in conjunction with such a security policy all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible." ::= { lookupCtlEntry 1 } lookupCtlOperationName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a lookup operation. This is locally unique, within the scope of an lookupCtlOwnerIndex." ::= { lookupCtlEntry 2 } lookupCtlTargetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the type of address for either performing a gethostbyname or a gethostbyaddr function at a remote host. Specification of dns(16) as the value for this object means that the gethostbyname function should be performed to return one or more numeric addresses. Use of a value of either ipv4(1) or ipv6(2) means that the gethostbyaddr function should be used to return the symbolic names associated with a remote host." ::= { lookupCtlEntry 3 } lookupCtlTargetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the address used for a resolver lookup at a remote host. The corresponding lookupCtlTargetAddressType objects determines its type as well as the function that can be requested. A value for this object MUST be set prior to transitioning its corresponding lookupCtlEntry to active(1) via lookupCtlRowStatus." ::= { lookupCtlEntry 4 } lookupCtlOperStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- operation is active notStarted(2), -- operation has not started completed(3) -- operation is done } MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the operational state of an lookupCtlEntry: enabled(1) - Operation is active. notStarted(2) - Operation has not been enabled. completed(3) - Operation has completed. An operation is automatically enabled(1) when its lookupCtlRowStatus object is transitioned to active(1) status. Until this occurs lookupCtlOperStatus MUST report a value of notStarted(2). After the lookup operation completes (success or failure) the value for lookupCtlOperStatus MUST be transitioned to completed(3)." ::= { lookupCtlEntry 5 } lookupCtlTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Reports the number of milliseconds that a lookup operation required to be completed at a remote host. Completed means operation failure as well as success." ::= { lookupCtlEntry 6 } lookupCtlRc OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The system specific return code from a lookup operation. All implementations MUST return a value of 0 for this object when the remote lookup operation succeeds. A non-zero value for this objects indicates failure. It is recommended that implementations that support errno use it as the value of this object to aid a management application in determining the cause of failure." ::= { lookupCtlEntry 7 } lookupCtlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows entries to be created and deleted in the lookupCtlTable. A remote lookup operation is started when an entry in this table is created via an SNMP SET request and the entry is activated. This occurs by setting the value of this object to CreateAndGo(4) during row creation or by setting this object to active(1) after the row is created. A value MUST be specified for lookupCtlTargetAddress prior to a transition to active(1) state being accepted. A remote lookup operation starts when its entry first becomes active(1). Transitions in and out of active(1) state have no effect on the operational behavior of a remote lookup operation, with the exception that deletion of an entry in this table by setting its RowStatus object to destroy(6) will stop an active remote lookup operation. The operational state of a remote lookup operation can be determined by examination of its lookupCtlOperStatus object." REFERENCE "See definition of RowStatus in RFC 2579, 'Textual Conventions for SMIv2.'" ::= { lookupCtlEntry 8 } -- Lookup Results Table lookupResultsTable OBJECT-TYPE SYNTAX SEQUENCE OF LookupResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Lookup Results Table for providing the capability of determining the results of a operation at a remote host. One or more entries are added to the lookupResultsTable when a lookup operation, as reflected by an lookupCtlEntry, completes successfully. All entries related to a successful lookup operation MUST be added to the lookupResultsTable at the same time that the associating lookupCtlOperStatus object is transitioned to completed(2). The number of entries added depends on the results determined for a particular lookup operation. All entries associated with an lookupCtlEntry are removed when the lookupCtlEntry is deleted. A remote host can be multi-homed and have more than one IP address associated with it (gethostbyname results) and/or it can have more than one symbolic name (gethostbyaddr results). The gethostbyaddr function is called with a host address as its parameter and is used primarily to determine a symbolic name to associate with the host address. Entries in the lookupResultsTable MUST be made for each host name returned. The official host name MUST be assigned a lookupResultsIndex of 1. The gethostbyname function is called with a symbolic host name and is used primarily to retrieve a host address. If possible the primary host address SHOULD be assigned a lookupResultsIndex of 1." ::= { lookupObjects 4 } lookupResultsEntry OBJECT-TYPE SYNTAX LookupResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the lookupResultsTable. The first two index elements identify the lookupCtlEntry that a lookupResultsEntry belongs to. The third index element selects a single lookup operation result." INDEX { lookupCtlOwnerIndex, lookupCtlOperationName, lookupResultsIndex } ::= { lookupResultsTable 1 } LookupResultsEntry ::= SEQUENCE { lookupResultsIndex Unsigned32, lookupResultsAddressType InetAddressType, lookupResultsAddress InetAddress } lookupResultsIndex OBJECT-TYPE SYNTAX Unsigned32 (1..'ffffffff'h) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries in the lookupResultsTable are created when the result of a lookup operation is determined. Entries MUST be stored in the lookupResultsTable in the order that they are retrieved. Values assigned to lookupResultsIndex MUST start at 1 and increase consecutively." ::= { lookupResultsEntry 1 } lookupResultsAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of result of a remote lookup operation. A value of unknown(0) implies that either the operation hasn't been started or that it has failed." ::= { lookupResultsEntry 2 } lookupResultsAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects a result for a remote lookup operation as per the value of lookupResultsAddressType. The address type (InetAddressType) that relates to this object is specified by the corresponding value of lookupResultsAddress." ::= { lookupResultsEntry 3 } -- Conformance information -- Compliance statements lookupCompliances OBJECT IDENTIFIER ::= { lookupConformance 1 } lookupGroups OBJECT IDENTIFIER ::= { lookupConformance 2 } -- Compliance statements lookupCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the DISMAN-NSLOOKUP-MIB." MODULE -- this module MANDATORY-GROUPS { lookupGroup } OBJECT lookupMaxConcurrentRequests MIN-ACCESS read-only DESCRIPTION "The agent is not required to support SET operations to this object." OBJECT lookupPurgeTime MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object." ::= { lookupCompliances 1 } lookupMinimumCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The minimum compliance statement for SNMP entities which implement the minimal subset of the DISMAN-NSLOOKUP-MIB. Implementors might choose this subset for small devices with limited resources." MODULE -- this module MANDATORY-GROUPS { lookupGroup } OBJECT lookupMaxConcurrentRequests MIN-ACCESS read-only DESCRIPTION "The agent is not required to support SET operations to this object." OBJECT lookupPurgeTime MIN-ACCESS read-only DESCRIPTION "The agent is not required to support a SET operation to this object." OBJECT lookupCtlRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported then at least one entry in the lookupCtlTable MUST be established already when the SNMP agent starts offering access to the NSLOOKUP-MIB module. If in such a case only a single entry is offered, then it is RECOMMENDED that this entry uses strings with a length of 0 for both of its two index objects." ::= { lookupCompliances 2 } -- MIB groupings lookupGroup OBJECT-GROUP OBJECTS { lookupMaxConcurrentRequests, lookupPurgeTime, lookupCtlOperStatus, lookupCtlTargetAddressType, lookupCtlTargetAddress, lookupCtlTime, lookupCtlRc, lookupCtlRowStatus, lookupResultsAddressType, lookupResultsAddress } STATUS current DESCRIPTION "The group of objects that comprise the remote Lookup operation." ::= { lookupGroups 1 } END -- -- Copyright (C) The Internet Society (2004). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implmentation may be prepared, copied, published and -- distributed, in whole or in part, without restriction of any kind, -- provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this -- document itself may not be modified in any way, such as by removing -- the copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of -- developing Internet standards in which case the procedures for -- copyrights defined in the Internet Standards process must be -- followed, or as required to translate it into languages other than -- English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- -- This document and the information contained herein is provided on an -- "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING -- TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING -- BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION -- HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF -- MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.