-- extracted from draft-ietf-ipcdn-qos-mib-05.txt -- at Sat Mar 3 06:04:38 2001 DOCS-QOS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, IpAddress, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, MacAddress, RowStatus, TruthValue, DisplayString, TimeStamp FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF ifIndex, InterfaceIndex FROM IF-MIB docsIfMib FROM DOCS-IF-MIB; docsQosMIB MODULE-IDENTITY LAST-UPDATED "200103010000Z" -- March 1, 2001 ORGANIZATION "IETF IPCDN Working Group" CONTACT-INFO " Co-Author: Michael Patrick Postal: Motorola ISG 20 Cabot Blvd, MS M4-30 Mansfield, MA 02048-1193 U.S.A. Phone: +1 508 261 5707 E-mail: michael.patrick@motorola.com" DESCRIPTION "This is the management information for Quality Of Service (QOS) for DOCSIS 1.1." REVISION "200103010000Z" -- March 1, 2001 DESCRIPTION "Published as draft-ietf-ipcdn-qos-mib-05.txt. Changes from qos-mib-04 include: - Changed default value of docsQosPktClassIpSourceMask and docsQosPktClassIpDestMask to 255.255.255.255. This is the only functional change of the revision. - Clarified description of dosQosServiceFlowPkts to avoid requiring CMs to classify downstream packets. - Clarified that docsQosServiceFlowPHSUnknowns only applies to received packets. - Clarified that docsQosPktClassBitMap and docsQosParamSetBitMap indicate all parameters for both adds and changes. " ::= { docsIfMib 7 } -- BPIPlus mib is docsIfMIb 6 docsQosMIBObjects OBJECT IDENTIFIER ::= { docsQosMIB 1 } -- Textual Conventions IfDirection ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates a direction on an RF MAC interface. The value downstream(1) is from Cable Modem Termination System to Cable Modem. The value upstream(2) is from Cable Modem to Cable Modem Termination System." SYNTAX INTEGER { downstream(1), upstream(2) } BitRate ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The rate of traffic in unit of bits per second. Used to specify traffic rate for QOS." SYNTAX Unsigned32 SchedulingType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The scheduling service provided by a CMTS for an upstream service flow. If the parameter is omitted from an upstream QOS Parameter Set, this object takes the value of bestEffort (2). This parameter must be reported as undefined (1) for downstream QOS Parameter Sets." SYNTAX INTEGER { undefined (1), bestEffort (2), nonRealTimePollingService(3), realTimePollingService(4), unsolictedGrantServiceWithAD(5), unsolictedGrantService(6) } ----------------------------------------------------------------------- -- -- Packet Classifier Table -- docsQosPktClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the packet classification configured on the CM or CMTS. The model is that a packet either received as input from an interface or transmitted for output on an interface may be compared against an ordered list of rules pertaining to the packet contents. Each rule is a row of this table. A matching rule provides a service flow id to to which the packet is classified. All rules need to match for a packet to match a classifier. The objects in this row correspond to a set of Classifier Encoding parameters in a DOCSIS MAC management message. The docsQosPktClassBitMap indicates which particular parameters were present in the classifier as signalled in the DOCSIS message. If the referenced parameter was not present in the signalled DOCSIS 1.1 Classifier, the corresponding object in this row reports a value as specified in the DESCRIPTION section. " ::= { docsQosMIBObjects 1 } docsQosPktClassEntry OBJECT-TYPE SYNTAX DocsQosPktClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table provides a single packet classifier rule. The index ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosServiceFlowId, docsQosPktClassId } ::= { docsQosPktClassTable 1 } DocsQosPktClassEntry ::= SEQUENCE { docsQosPktClassId Integer32, docsQosPktClassDirection IfDirection, docsQosPktClassPriority Integer32, docsQosPktClassIpTosLow OCTET STRING, docsQosPktClassIpTosHigh OCTET STRING, docsQosPktClassIpTosMask OCTET STRING, docsQosPktClassIpProtocol Integer32, docsQosPktClassIpSourceAddr IpAddress, docsQosPktClassIpSourceMask IpAddress, docsQosPktClassIpDestAddr IpAddress, docsQosPktClassIpDestMask IpAddress, docsQosPktClassSourcePortStart Integer32, docsQosPktClassSourcePortEnd Integer32, docsQosPktClassDestPortStart Integer32, docsQosPktClassDestPortEnd Integer32, docsQosPktClassDestMacAddr MacAddress, docsQosPktClassDestMacMask MacAddress, docsQosPktClassSourceMacAddr MacAddress, docsQosPktClassEnetProtocolType INTEGER, docsQosPktClassEnetProtocol Integer32, docsQosPktClassUserPriLow Integer32, docsQosPktClassUserPriHigh Integer32, docsQosPktClassVlanId Integer32, docsQosPktClassState INTEGER, docsQosPktClassPkts Counter32, docsQosPktClassBitMap BITS } docsQosPktClassId OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index assigned to packet classifier entry by the CMTS which is unique per service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.2" ::= { docsQosPktClassEntry 1 } docsQosPktClassDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the direction to which the classifier is applied." ::= { docsQosPktClassEntry 2 } docsQosPktClassPriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The value specifies the order of evaluation of the classifiers. The higher the value the higher the priority. The value of 0 is used as default in provisioned service flows classifiers. The default value of 64 is used for dynamic service flow classifiers. If the referenced parameter is not present in a classifier, this object reports the default value as defined above." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.5" ::= { docsQosPktClassEntry 3 } docsQosPktClassIpTosLow OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 4 } docsQosPktClassIpTosHigh OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 5 } docsQosPktClassIpTosMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mask value is bitwise ANDed with TOS byte in an IP packet and this value is used check range checking of TosLow and TosHigh. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.1" ::= { docsQosPktClassEntry 6 } docsQosPktClassIpProtocol OBJECT-TYPE SYNTAX Integer32 (0..258) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of the IP Protocol field required for IP packets to match this rule. The value 256 matches traffic with any IP Protocol value. The value 257 by convention matches both TCP and UDP. If the referenced parameter is not present in a classifier, this object reports the value of 258." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.2" ::= { docsQosPktClassEntry 7 } docsQosPktClassIpSourceAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet ip source address bitwise ANDed with the docsQosPktClassIpSourceMask value equals the docsQosPktClassIpSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.3" ::= { docsQosPktClassEntry 8 } docsQosPktClassIpSourceMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Source Address that are compared to match this rule. An IP packet matches the rule when the packet source address bitwise ANDed with the docsQosPktClassIpSourceMask value equals the docsQosIpPktClassSourceAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 255.255.255.255." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.4" ::= { docsQosPktClassEntry 9 } docsQosPktClassIpDestAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP destination address bitwise ANDed with the docsQosPktClassIpDestMask value equals the docsQosPktClassIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 255.255.255.255." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.5" ::= { docsQosPktClassEntry 10 } docsQosPktClassIpDestMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies which bits of a packet's IP Destination Address that are compared to match this rule. An IP packet matches the rule when the packet destination address bitwise ANDed with the docsQosPktClassIpDestMask value equals the docsQosPktClassIpDestAddr value. If the referenced parameter is not present in a classifier, this object reports the value of 0.0.0.0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.6" ::= { docsQosPktClassEntry 11} docsQosPktClassSourcePortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.7" ::= { docsQosPktClassEntry 12 } docsQosPktClassSourcePortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP source port numbers to which a packet is compared. This object is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.9" ::= { docsQosPktClassEntry 13 } docsQosPktClassDestPortStart OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the low end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 0." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.9" ::= { docsQosPktClassEntry 14 } docsQosPktClassDestPortEnd OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the high end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this object reports the value of 65535." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.5.10" ::= { docsQosPktClassEntry 15 } docsQosPktClassDestMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.1" ::= { docsQosPktClassEntry 16 } docsQosPktClassDestMacMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with docsQosPktClassDestMacMask equals the value of docsQosPktClassDestMacAddr. If the referenced parameter is not present in a classifier, this object reports the value of '000000000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.1" ::= { docsQosPktClassEntry 17 } docsQosPktClassSourceMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An Ethernet packet matches this entry when its source MAC address equals the value of this object. If the referenced parameter is not present in a classifier, this object reports the value of 'FFFFFFFFFFFF'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.2" ::= { docsQosPktClassEntry 18 } docsQosPktClassEnetProtocolType OBJECT-TYPE SYNTAX INTEGER { none(0), ethertype(1), dsap(2), mac(3), all(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the format of the layer 3 protocol id in the Ethernet packet. A value of none(0) means that the rule does not use the layer 3 protocol type as a matching criteria. A value of ethertype(1) means that the rule applies only to frames which contains an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of dsap(2) means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of mac(3) means that the rule applies only to MAC management messages for MAC management messages. A value of all(4) means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this object reports the value of 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.3" ::= { docsQosPktClassEntry 19 } docsQosPktClassEnetProtocol OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "If docsQosEthPktClassProtocolType is none(0), this object is ignored when considering whether a packet matches the current rule. If dosQosPktClassEnetProtocolType is ethertype(1), this object gives the 16-bit value of the EtherType that the packet must match in order to match the rule. If docsQosPktClassEnetProtocolType is dsap(2), the lower 8 bits of this object's value must match the DSAP byte of the packet in order to match the rule. If docsQosPktClassEnetProtocolType is mac(3), the lower 8 bits of this object value represent a lower bound (inclusive) of MAC management message type codes matched, and the upper 8 bits of this object value represent the upper bound (inclusive) of matched MAC message type codes. Certain message type codes are excluded from matching, as specified in the reference. If the Ethernet frame contains an 802.1P/Q Tag header (i.e. EtherType 0x8100), this object applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in the classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.6.3" ::= { docsQosPktClassEntry 20 } -- docsQosPktClassUserPriApplies { docsQosPktClassEntry 21 } -- was removed in revision -03. docsQosPktClassUserPriLow OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of docsQosPktClassPriLow and docsQosPktClassPriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.1" ::= { docsQosPktClassEntry 22 } docsQosPktClassUserPriHigh OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Qtag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3 bit Priority field and a 12 bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of docsQosPktClassPriLow and docsQosPktClassPriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this object is reported as 7. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.1" ::= { docsQosPktClassEntry 23 } docsQosPktClassVlanId OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object applies only to Ethernet frames using the 802.1P/Q tag header. If this object's value is nonzero, tagged packets must have a VLAN Identifier that matches the value in order to match the rule. Only the least significant 12 bits of this object's value are valid. If the referenced parameter is not present in the classifier, the value of this object is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.7.2" ::= { docsQosPktClassEntry 24 } docsQosPktClassState OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classifier, the value of this object is reported as active(1). " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.6" ::= { docsQosPktClassEntry 25 } docsQosPktClassPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object counts the number of packets that have been classified using this entry." ::= { docsQosPktClassEntry 26 } docsQosPktClassBitMap OBJECT-TYPE SYNTAX BITS { -- Reference SP-RFIv1.1-I05-000714 rulePriority(0), -- Appendix C.2.1.3.4 activationState(1), -- Appendix C.2.1.3.6 ipTos(2), -- Appendix C.2.1.5.1 ipProtocol(3), -- Appendix C.2.1.5.2 ipSourceAddr(4), -- Appendix C.2.1.5.3 ipSourceMask(5), -- Appendix C.2.1.5.4 ipDestAddr(6), -- Appendix C.2.1.5.5 ipDestMask(7), -- Appendix C.2.1.5.6 sourcePortStart(8), -- Appendix C.2.1.5.7 sourcePortEnd(9), -- Appendix C.2.1.5.8 destPortStart(10), -- Appendix C.2.1.5.9 destPortEnd(11), -- Appendix C.2.1.5.10 destMac(12), -- Appendix C.2.1.6.1 sourceMac(13), -- Appendix C.2.1.6.2 ethertype(14), -- Appendix C.2.1.6.3 userPri(15), -- Appendix C.2.1.7.1 vlanId(16) -- Appendix C.2.1.7.2 } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates which parameter encodings were actually present in the DOCSIS packet classifier encoding signalled in the DOCSIS message that created or modified the classifier. Note that Dynamic Service Change messages have replace semantics, so that all non-default parameters must be present whether the classifier is being created or changed. A bit of of this object is set to 1 if the parameter indicated by the comment was present in the classifier encoding, and 0 otherwise. Note that BITS are encoded most significant bit first, so that if e.g. bits 6 and 7 are set, this object is encoded as the octet string '030000'H. " ::= { docsQosPktClassEntry 27 } -- -- QOS Parameter Set Table -- docsQosParamSetTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosParamSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of DOCSIS 1.1 QOS parameters defined in a managed device. The ifIndex index specifies a DOCSIS MAC Domain. The docsQosServiceFlowId index specifies a particular Service Flow. The docsQosParamSetType index indicates whether the active, admitted, or provisioned QOS Parameter Set is being described by the row. Only the QOS Parameter Sets of Docsis 1.1 service flows are represented in this table. Docsis 1.0 QOS service profiles are not represented in this table. Each row corresponds to a DOCSIS QOS Parameter Set as signaled via DOCSIS MAC management messages. Each object in the row corresponds to one or part of one DOCSIS 1.1 Service Flow Encoding. The docsQosParamSetBitMap object in the row indicates which particular parameters were signalled in the original registration or dynamic service request message that created the QOS Parameter Set. In many cases, even if a QOS Parameter Set parameter was not signalled, the DOCSIS specification calls for a default value to be used. That default value is reported as the value of the corresponding object in this row. Many objects are not applicable depending on the service flow direction or upstream scheduling type. The object value reported in this case is specified in the DESCRIPTION clause. " ::= { docsQosMIBObjects 2 } docsQosParamSetEntry OBJECT-TYPE SYNTAX DocsQosParamSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique set of QOS parameters." INDEX { ifIndex, docsQosServiceFlowId, docsQosParamSetType } ::= { docsQosParamSetTable 2 } -- Type of docsQosParamSet Entry { docsQosParamSetTable 1 } was -- changed with revision -03 DocsQosParamSetEntry ::= SEQUENCE { docsQosParamSetServiceClassName DisplayString, docsQosParamSetPriority Integer32, docsQosParamSetMaxTrafficRate BitRate, docsQosParamSetMaxTrafficBurst Unsigned32, docsQosParamSetMinReservedRate BitRate, docsQosParamSetMinReservedPkt Integer32, docsQosParamSetActiveTimeout Integer32, docsQosParamSetAdmittedTimeout Integer32, docsQosParamSetMaxConcatBurst Integer32, docsQosParamSetSchedulingType SchedulingType, docsQosParamSetNomPollInterval Unsigned32, docsQosParamSetTolPollJitter Unsigned32, docsQosParamSetUnsolicitGrantSize Integer32, docsQosParamSetNomGrantInterval Unsigned32, docsQosParamSetTolGrantJitter Unsigned32, docsQosParamSetGrantsPerInterval Integer32, docsQosParamSetTosAndMask OCTET STRING, docsQosParamSetTosOrMask OCTET STRING, docsQosParamSetMaxLatency Unsigned32, docsQosParamSetType INTEGER, docsQosParamSetRequestPolicyOct OCTET STRING, docsQosParamSetBitMap BITS } -- Removed docsQosParamSetRowType { docsQosParamSetEntry 1 } -- with revision -03 -- Removed docsQosParamSetIndex { docsQosParamSetEntry 2 } -- with revision -03 -- Removed docsQosParamSetRowStatus { docsQosParamSetEntry 3} -- with revision -03 docsQosParamSetServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Refers to the Service Class Name that the parameter set values were derived. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is a zero length string. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.4" ::= { docsQosParamSetEntry 4 } docsQosParamSetPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "The relative priority of a service flow. Higher numbers indicate higher priority. This priority should only be used to differentiate service flow with identical parameter sets. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, the reported value is 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.2" ::= { docsQosParamSetEntry 5 } docsQosParamSetMaxTrafficRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum sustained traffic rate allowed for this service flow in bits/sec. Must count all MAC frame data PDU from the bytes following the MAC header HCS to the end of the CRC. The number of bytes forwarded is limited during any time interval. The value 0 means no maximum traffic rate is enforced. This object applies to both upstream and downstream service flows. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.3" ::= { docsQosParamSetEntry 6 } docsQosParamSetMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the token bucket size in bytes for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This object is applied in conjunction with docsQosParamSetMaxTrafficRate to calculate maximum sustained traffic rate. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object for scheduling types bestEffort (2), nonRealTimePollingService(3), and realTimePollingService(4) is 1522. If this parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.4" ::= { docsQosParamSetEntry 7 } docsQosParamSetMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. The default value of 0 has the meaning that no bandwidth is reserved. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.5" ::= { docsQosParamSetEntry 8 } docsQosParamSetMinReservedPkt OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies an assumed minimum packet size in bytes for which the docsQosParamSetMinReservedRate will be provided. The value is calculated from the byte following the MAC header HCS to the end of the CRC. If the referenced parameter is omitted from a DOCSIS QOS parameter set, the default value is CMTS implementation dependent. In this case, the CMTS reports the default value it is using and the CM reports a value of 0. If the referenced parameter is not applicable to the direction or scheduling type of the service flow, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.6" ::= { docsQosParamSetEntry 9 } docsQosParamSetActiveTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum duration in seconds that resources remain unused on an active service flow before CMTS signals that both active and admitted parameters set are null. The default value of 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.7" ::= { docsQosParamSetEntry 10 } docsQosParamSetAdmittedTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum duration in seconds that resources remain in admitted state before resources must be released. The value of 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 200. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.8" DEFVAL { 200 } ::= { docsQosParamSetEntry 11 } docsQosParamSetMaxConcatBurst OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum concatenated burst in bytes which an upstream service flow is allowed. The value is calculated from the FC byte of the Concatenation MAC Header to the last CRC byte in of the last concatenated MAC frame, inclusive. The value of 0 specifies no maximum burst. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, this object's value is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.1" ::= { docsQosParamSetEntry 12 } docsQosParamSetSchedulingType OBJECT-TYPE SYNTAX SchedulingType MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set of an upstream service flow, the default value of this object is bestEffort(2). For QOS parameter sets of downstream service flows, this object's value is reported as undefined(1). " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.2" ::= { docsQosParamSetEntry 13 } -- Changed type of docsQosParamSetRequestPolicy { docsQosParamSetEntry 14 } -- to docsQosParamSetRequestPolicyOct { docsQosParamSetEntry 25 } docsQosParamSetNomPollInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the nominal interval in microseconds between successive unicast request opportunities on an upstream service flow. This object applies only to upstream service flows with schedulingType of value nonRealTimePollingService(3), realTimePollingService(4), and unsolictedGrantServiceWithAD(5). The parameter is mandatory for realTimePollingService(4). If the parameter is omitted with nonRealTimePollingService(3), the CMTS uses an implementation dependent value. If the parameter is omitted with unsolictedGrantServiceWithAD(5), the CMTS uses as a default value the value of the Nominal Grant Interval parameter. In all cases, the CMTS reports the value it is using when the parameter is applicable. The CM reports the signaled parameter value if it was signaled, and 0 otherwise. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.4" ::= { docsQosParamSetEntry 15 } docsQosParamSetTolPollJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum amount of time in microseconds that the unicast request interval may be delayed from the nominal periodic schedule on an upstream service flow. This parameter is applicable only to upstream service flows with a Schedulingtype of realTimePollingService(4) or unsolictedGrantServiceWithAD(5). If the referenced parameter is applicable but not present in the corresponding DOCSIS QOS Parameter Set, the CMTS uses an implementation dependent value and reports the value it is using. The CM reports a value of 0 in this case. If the parameter is not applicable to the direction or upstream scheduling type of the service flow, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.5" ::= { docsQosParamSetEntry 16 } docsQosParamSetUnsolicitGrantSize OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the unsolicited grant size in bytes. The grant size includes the entired MAC frame data PDU from the Frame Control byte to end of the MAC frame. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.6" ::= { docsQosParamSetEntry 17 } docsQosParamSetNomGrantInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the nominal interval in microseconds between successive data grant opportunities on an upstream service flow. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.7" ::= { docsQosParamSetEntry 18 } docsQosParamSetTolGrantJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum amount of time in microseconds that the transmission opportunities may be delayed from the nominal periodic schedule. The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.8" ::= { docsQosParamSetEntry 19 } docsQosParamSetGrantsPerInterval OBJECT-TYPE SYNTAX Integer32 (0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of data grants per Nominal Grant Interval (docsQosParamSetNomGrantInterval). The referenced parameter is applicable only for upstream flows with a SchedulingType of of unsolicitedGrantServicewithAD(5) or unsolicitedGrantService(6), and is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this object's value as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.9" ::= { docsQosParamSetEntry 20 } docsQosParamSetTosAndMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the AND mask for IP TOS byte for overwriting IP packets TOS value. The IP packets TOS byte is bitwise ANDed with docsQosParamSetTosAndMask and result is bitwise ORed with docsQosParamSetTosORMask and result is written to IP packet TOS byte. A value of 'FF'H for docsQosParamSetTosAndMask and a value of '00'H for docsQosParamSetTosOrMask means that IP Packet TOS byte is not overwritten. This combination is reported if the referenced parameter is not present in a QOS Parameter Set." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.10" ::= { docsQosParamSetEntry 21 } docsQosParamSetTosOrMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the OR mask for IP TOS byte. See the description of docsQosParamSetTosAndMask for further details." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.10" ::= { docsQosParamSetEntry 22 } docsQosParamSetMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum latency between the reception of a packet by the CMTS on its NSI and the forwarding of the packet to the RF interface. A value of 0 signifies no maximum latency enforced. This object only applies to downstream service flows. If the referenced parameter is not present in the corresponding downstream DOCSIS QOS Parameter Set, the default value is 0. This parameter is not applicable to upstream DOCSIS QOS Parameter Sets, and its value is reported as 0 in this case. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.7.1" ::= { docsQosParamSetEntry 23 } docsQosParamSetType OBJECT-TYPE SYNTAX INTEGER { active (1), admitted (2), provisioned (3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the type of the QOS parameter set defined by this row. active(1) indicates the Active QOS parameter set, describing the service currently being provided by the Docsis MAC domain to the service flow. admitted(2) indicates the Admitted QOS Parameter Set, describing services reserved by by the Docsis MAC domain for use by the service flow. provisioned (3) describes the QOS Parameter Set defined in the DOCSIS CM Configuration file for the service flow." REFERENCE "SP-RFIv1.1-I05-000714, 8.1.5" ::= { docsQosParamSetEntry 24 } docsQosParamSetRequestPolicyOct OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) -- A 32-bit mask represented most significant byte -- first. The 32 bit integer represented in this manner -- equals the binary value of the referenced integer -- parameter of the DOCSIS RFI specification. -- The BITS syntax is not used in order to avoid -- the confusion caused by different bit numbering -- conventions. MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies which transmit interval opportunities the CM omits for upstream transmission requests and packet transmissions. This object takes its default value for downstream service flows. Unless otherwise indicated, a bit value of 1 means that a CM must *not* use that opportunity for upstream transmission. Calling bit 0 the least significant bit of the least significant (4th) octet, and increasing bit number with significance, the bit definitions are as defined below: broadcastReqOpp(0): all CMs broadcast request opportunities priorityReqMulticastReq(1): priority request multicast request opportunities reqDataForReq(3): request/data opportunities for requests reqDataForData(4): request/data opportunities for data concatenateData(5): concatenate data fragmentData(6): fragment data suppresspayloadheaders(7): suppress payload headers dropPktsExceedUGSize(8): A value of 1 mean that service flow must drop packet that do not fit in the Unsolicited Grant size If the referenced parameter is not present in a QOS Parameter Set, the value of this object is reported as '00000000'H. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.6.3" ::= { docsQosParamSetEntry 25 } docsQosParamSetBitMap OBJECT-TYPE -- Each bit corresponds to a parameter -- from SP-RFI-v1.1-I05-000714, Appendix C SYNTAX BITS { -- in the indicated section number. trafficPriority(0), -- C.2.2.5.2 maxTrafficRate(1), -- C.2.2.5.3 maxTrafficBurst(2), -- C.2.2.5.4 minReservedRate(3), -- C.2.2.5.5 minReservedPkt(4), -- C.2.2.5.6 activeTimeout(5), -- C.2.2.5.7 admittedTimeout(6), -- C.2.2.5.8 maxConcatBurst(7), -- C.2.2.6.1 schedulingType(8), -- C.2.2.6.2 requestPolicy(9), -- C.2.2.6.3 nomPollInterval(10), -- C.2.2.6.4 tolPollJitter(11), -- C.2.2.6.5 unsolicitGrantSize(12), -- C.2.2.6.6 nomGrantInterval(13), -- C.2.2.6.7 tolGrantJitter(14), -- C.2.2.6.8 grantsPerInterval(15), -- C.2.2.6.9 tosOverwrite(16), -- C.2.2.6.10 maxLatency(17) -- C.2.2.7.1 } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the set of QOS Parameter Set parameters actually signaled in the DOCSIS registration or dynamic service request message that created or modified the QOS Parameter Set. A bit is set to 1 when the parameter described by the indicated reference section is present in the original request. Note that when Service Class names are expanded, the registration or dynamic response message may contain parameters as expanded by the CMTS based on a stored service class. These expanded parameters are *not* indicated by a 1 bit in this object. Note that even though some QOS Parameter Set parameters may not be signalled in a message (so that the paramater's bit in this object is 0) the DOCSIS specification calls for default values to be used. These default values are reported as the corresponding object's value in the row. Note that BITS objects are encoded most significant bit first. For example, if bits 1 and 16 are set, the value of this object is the octet string '400080'H. " ::= { docsQosParamSetEntry 26 } -- -- Service Flow Table -- docsQosServiceFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Flows in a managed device. " ::= { docsQosMIBObjects 3 } docsQosServiceFlowEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a service flow. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosServiceFlowId } ::= { docsQosServiceFlowTable 1 } DocsQosServiceFlowEntry ::= SEQUENCE { docsQosServiceFlowId Unsigned32, docsQosServiceFlowSID Unsigned32, docsQosServiceFlowDirection IfDirection, docsQosServiceFlowPrimary TruthValue } docsQosServiceFlowId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index assigned to a service flow by CMTS." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.2" ::= { docsQosServiceFlowEntry 1 } -- Remove docsQosServiceFlowProvisionedParamSetIndex -- {docsQosServiceFlowEntry 2} with revision -03 -- Remove docsQosServiceFlowAdmittedParamSetIndex -- {docsQosServiceFlowEntry 3} with revision -03 -- Remove docsQosServiceFlowActiveParamSetIndex -- {docsQosServiceFlowEntry 4} with revision -03 docsQosServiceFlowSID OBJECT-TYPE SYNTAX Unsigned32 (0..16383) MAX-ACCESS read-only STATUS current DESCRIPTION "Service Identifier (SID) assigned to an admitted or active service flow. This object reports a value of 0 if a Service Id is not associated with the service flow. Only active or admitted upstream service flows will have a Service Id (SID)." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.3" ::= { docsQosServiceFlowEntry 6 } docsQosServiceFlowDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-only STATUS current DESCRIPTION "The direction of the service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.1/2" ::= { docsQosServiceFlowEntry 7 } docsQosServiceFlowPrimary OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Object reflects whether service flow is the primary or a secondary service flow. A primary service flow is the default service flow for otherwise unclassified traffic and all MAC messages." REFERENCE "SP-RFIv1.1-I05-000714, Section 8.1 " ::= { docsQosServiceFlowEntry 8 } -- Moved docsQosServiceFlow'ActiveTimeout, 'AdmittedTimeout, -- 'SchedulingType, 'RequestPolicy, 'TosAndMask, and 'TosOrMask -- back to docsQosParamSetTable with QOS-MIB-04. -- -- Service Flow Stats Table -- docsQosServiceFlowStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with the Service Flows in a managed device. " ::= { docsQosMIBObjects 4 } docsQosServiceFlowStatsEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of service flow statistics. An entry in the table exists for each Service Flow ID. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosServiceFlowId } ::= { docsQosServiceFlowStatsTable 1 } DocsQosServiceFlowStatsEntry ::= SEQUENCE { docsQosServiceFlowPkts Counter32, docsQosServiceFlowOctets Counter32, docsQosServiceFlowTimeCreated TimeStamp, docsQosServiceFlowTimeActive Counter32, docsQosServiceFlowPHSUnknowns Counter32, docsQosServiceFlowPolicedDropPkts Counter32, docsQosServiceFlowPolicedDelayPkts Counter32 } docsQosServiceFlowPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Packet Data PDUs classified to this service flow. This object does not count MAC-specific management messages. CMs not classifying downstream packets may report this object's value as 0. " ::= { docsQosServiceFlowStatsEntry 1 } docsQosServiceFlowOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets transmitted on the Docsis RF network from the byte after the MAC header HCS to the end of the CRC for all packets counted in the docsQosServiceFlowPkts object for this row. Note that this counts the octets after payload header suppression has been applied. CMs not classifying to a downstream service flow may report this object's value as 0 for that flow. " ::= { docsQosServiceFlowStatsEntry 2 } docsQosServiceFlowTimeCreated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was created." ::= { docsQosServiceFlowStatsEntry 3 } docsQosServiceFlowTimeActive OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The total time that service flow has been active." ::= { docsQosServiceFlowStatsEntry 4 } docsQosServiceFlowPHSUnknowns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received on the service flow with an unknown payload header suppression index." ::= { docsQosServiceFlowStatsEntry 5 } docsQosServiceFlowPolicedDropPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets dropped due to policing of the service flow, especially to limit the maximum rate of the flow." ::= { docsQosServiceFlowStatsEntry 6 } docsQosServiceFlowPolicedDelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packet delayed due to policing of the service flow, especially to limit the maximum rate of the flow." ::= { docsQosServiceFlowStatsEntry 7 } -- -- Upstream Service Flow Stats Table (CMTS ONLY) -- docsQosUpstreamStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosUpstreamStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with upstream service flows. All counted frames must be received without an FCS error." ::= { docsQosMIBObjects 5 } docsQosUpstreamStatsEntry OBJECT-TYPE SYNTAX DocsQosUpstreamStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of upstream service flow statistics. An entry in the table exists for each upstream Service Flow in a managed device. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosSID } ::= { docsQosUpstreamStatsTable 1 } DocsQosUpstreamStatsEntry ::= SEQUENCE { docsQosSID Integer32, docsQosUpstreamFragments Counter32, docsQosUpstreamFragDiscards Counter32, docsQosUpstreamConcatBursts Counter32 } docsQosSID OBJECT-TYPE SYNTAX Integer32 (1..16383) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies a service id for an admitted or active upstream service flow." ::= { docsQosUpstreamStatsEntry 1 } -- Renamed in revision -03 from docsQosUpstreamFragPkts docsQosUpstreamFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of fragmentation headers received on an upstream service flow, regardless of whether the fragment was correctly reassembled into a valid packet. " ::= { docsQosUpstreamStatsEntry 2 } docsQosUpstreamFragDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of upstream fragments discarded and not assembled into a valid upstream packet." ::= { docsQosUpstreamStatsEntry 3 } docsQosUpstreamConcatBursts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of concatenation headers received on an upstream service flow." ::= { docsQosUpstreamStatsEntry 4 } -- -- Dynamic Service Stats Table -- docsQosDynamicServiceStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosDynamicServiceStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics associated with the Dynamic Service Flows in a managed device. " ::= { docsQosMIBObjects 6 } docsQosDynamicServiceStatsEntry OBJECT-TYPE SYNTAX DocsQosDynamicServiceStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes a set of dynamic service flow statistics. Two entries exist for each Docsis mac layer interface for the upstream and downstream direction. On the CMTS, the downstream direction row indicates messages transmitted or transactions originated by the CMTS. The upstream direction row indicates messages received or transaction originated by the CM. On the CM, the downstream direction row indicates messages received or transactions originated by the CMTS. The upstream direction row indicates messages transmitted by the CM or transactions originated by the CM. The ifIndex is an ifType of docsCableMaclayer(127)." INDEX { ifIndex, docsQosIfDirection } ::= { docsQosDynamicServiceStatsTable 1 } DocsQosDynamicServiceStatsEntry ::= SEQUENCE { docsQosIfDirection IfDirection, docsQosDSAReqs Counter32, docsQosDSARsps Counter32, docsQosDSAAcks Counter32, docsQosDSCReqs Counter32, docsQosDSCRsps Counter32, docsQosDSCAcks Counter32, docsQosDSDReqs Counter32, docsQosDSDRsps Counter32, docsQosDynamicAdds Counter32, docsQosDynamicAddFails Counter32, docsQosDynamicChanges Counter32, docsQosDynamicChangeFails Counter32, docsQosDynamicDeletes Counter32, docsQosDynamicDeleteFails Counter32, docsQosDCCReqs Counter32, docsQosDCCRsps Counter32, docsQosDCCAcks Counter32, docsQosDCCs Counter32, docsQosDCCFails Counter32 } docsQosIfDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS not-accessible STATUS current DESCRIPTION "The direction of interface." ::= { docsQosDynamicServiceStatsEntry 1 } docsQosDSAReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Requests" ::= { docsQosDynamicServiceStatsEntry 2 } docsQosDSARsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Responses" ::= { docsQosDynamicServiceStatsEntry 3 } docsQosDSAAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Addition Acknowledgements." ::= { docsQosDynamicServiceStatsEntry 4 } docsQosDSCReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Requests" ::= { docsQosDynamicServiceStatsEntry 5 } docsQosDSCRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Responses" ::= { docsQosDynamicServiceStatsEntry 6 } docsQosDSCAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Change Acknowlegements." ::= { docsQosDynamicServiceStatsEntry 7 } docsQosDSDReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Delete Requests" ::= { docsQosDynamicServiceStatsEntry 8 } docsQosDSDRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Service Delete Responses" ::= { docsQosDynamicServiceStatsEntry 9 } docsQosDynamicAdds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Addition transactions." ::= { docsQosDynamicServiceStatsEntry 10 } docsQosDynamicAddFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Addition transactions." ::= { docsQosDynamicServiceStatsEntry 11 } docsQosDynamicChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Change transactions." ::= { docsQosDynamicServiceStatsEntry 12 } docsQosDynamicChangeFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Change transactions." ::= { docsQosDynamicServiceStatsEntry 13 } docsQosDynamicDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Service Delete transactions." ::= { docsQosDynamicServiceStatsEntry 14 } docsQosDynamicDeleteFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Service Delete transactions." ::= { docsQosDynamicServiceStatsEntry 15 } docsQosDCCReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Request messages traversing an interface. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 16 } docsQosDCCRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Response messages traversing an interface. This count is nonzero only on upstream direction rows." ::= { docsQosDynamicServiceStatsEntry 17 } docsQosDCCAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dynamic Channel Change Acknowledgement messages traversing an interface. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 18 } docsQosDCCs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 19 } docsQosDCCFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows." ::= { docsQosDynamicServiceStatsEntry 20 } -- -- Service Flow Log Table (CMTS ONLY) -- docsQosServiceFlowLogTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceFlowLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a log of the disconnected Service Flows in a managed device." ::= { docsQosMIBObjects 7 } docsQosServiceFlowLogEntry OBJECT-TYPE SYNTAX DocsQosServiceFlowLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single disconnected service flow." INDEX { docsQosServiceFlowLogIndex } ::= { docsQosServiceFlowLogTable 1 } DocsQosServiceFlowLogEntry ::= SEQUENCE { docsQosServiceFlowLogIndex Unsigned32, docsQosServiceFlowLogIfIndex InterfaceIndex, docsQosServiceFlowLogSFID Unsigned32, docsQosServiceFlowLogCmMac MacAddress, docsQosServiceFlowLogPkts Counter32, docsQosServiceFlowLogOctets Counter32, docsQosServiceFlowLogTimeDeleted TimeStamp, docsQosServiceFlowLogTimeCreated TimeStamp, docsQosServiceFlowLogTimeActive Counter32, docsQosServiceFlowLogDirection IfDirection, docsQosServiceFlowLogPrimary TruthValue, docsQosServiceFlowLogServiceClassName DisplayString, docsQosServiceFlowLogPolicedDropPkts Counter32, docsQosServiceFlowLogPolicedDelayPkts Counter32, docsQosServiceFlowLogControl INTEGER } docsQosServiceFlowLogIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Unique index for a logged service flow." ::= { docsQosServiceFlowLogEntry 1 } docsQosServiceFlowLogIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of ifType docsCableMacLayter(127) on the CMTS where the service flow was present." ::= { docsQosServiceFlowLogEntry 2 } docsQosServiceFlowLogSFID OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The index assigned to the service flow by the CMTS." ::= { docsQosServiceFlowLogEntry 3 } docsQosServiceFlowLogCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the cable modem associated with the service flow." ::= { docsQosServiceFlowLogEntry 4 } docsQosServiceFlowLogPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets counted on this service flow after payload header suppression." ::= { docsQosServiceFlowLogEntry 5 } docsQosServiceFlowLogOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets counted on this service flow after payload header suppression." ::= { docsQosServiceFlowLogEntry 6 } docsQosServiceFlowLogTimeDeleted OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was deleted." ::= { docsQosServiceFlowLogEntry 7 } docsQosServiceFlowLogTimeCreated OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the service flow was created." ::= { docsQosServiceFlowLogEntry 8 } docsQosServiceFlowLogTimeActive OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The total time that service flow was active." ::= { docsQosServiceFlowLogEntry 9 } -- docsQosServiceFlowLogControl was formerly { docsQosServiceFlowLogEntry 10} -- and was renumbered in version -04. docsQosServiceFlowLogDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-only STATUS current DESCRIPTION "The value of docsQosServiceFlowDirection for the service flow." ::= { docsQosServiceFlowLogEntry 11} docsQosServiceFlowLogPrimary OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The value of docsQosServiceFlowPrimary for the service flow." ::= { docsQosServiceFlowLogEntry 12} docsQosServiceFlowLogServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of docsQosParamSetServiceClassName for the provisioned QOS Parameter Set of the service flow." ::= { docsQosServiceFlowLogEntry 13} docsQosServiceFlowLogPolicedDropPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The final value of docsQosServiceFlowPolicedDropPkts for the service flow." ::= { docsQosServiceFlowLogEntry 14} docsQosServiceFlowLogPolicedDelayPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The final value of docsQosServiceFlowPolicedDelayPkts for the service flow." ::= { docsQosServiceFlowLogEntry 15} docsQosServiceFlowLogControl OBJECT-TYPE SYNTAX INTEGER { active(1), destroy(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to the value destroy(6) removes this entry from the table. Reading this object return the value active(1)." ::= { docsQosServiceFlowLogEntry 16} -- -- Service Class Table (CMTS ONLY) -- docsQosServiceClassTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Classes in a CMTS. " ::= { docsQosMIBObjects 8 } docsQosServiceClassEntry OBJECT-TYPE SYNTAX DocsQosServiceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A provisioned service class on a CMTS. Each entry defines a template for certain DOCSIS QOS Parameter Set values. When a CM creates or modifies an Admitted QOS Parameter Set for a Service Flow, it may reference a Service Class Name instead of providing explicit QOS Parameter Set values. In this case, the CMTS populates the QOS Parameter Set with the applicable corresponding values from the named Service Class. Subsequent changes to a Service Class row do *not* affect the QOS Parameter Set values of any service flows already admitted. A service class template applies to only a single direction, as indicated in the docsQosServiceClassDirection object. " INDEX { docsQosServiceClassName } ::= { docsQosServiceClassTable 1 } DocsQosServiceClassEntry ::= SEQUENCE { docsQosServiceClassName DisplayString (SIZE(1..15)), docsQosServiceClassStatus RowStatus, docsQosServiceClassPriority Integer32, docsQosServiceClassMaxTrafficRate BitRate, docsQosServiceClassMaxTrafficBurst Unsigned32, docsQosServiceClassMinReservedRate BitRate, docsQosServiceClassMinReservedPkt Integer32, docsQosServiceClassMaxConcatBurst Integer32, docsQosServiceClassNomPollInterval Unsigned32, docsQosServiceClassTolPollJitter Unsigned32, docsQosServiceClassUnsolicitGrantSize Integer32, docsQosServiceClassNomGrantInterval Unsigned32, docsQosServiceClassTolGrantJitter Unsigned32, docsQosServiceClassGrantsPerInterval Integer32, docsQosServiceClassMaxLatency Unsigned32, docsQosServiceClassActiveTimeout Integer32, docsQosServiceClassAdmittedTimeout Integer32, docsQosServiceClassSchedulingType SchedulingType, docsQosServiceClassRequestPolicy OCTET STRING (SIZE(4)), docsQosServiceClassTosAndMask OCTET STRING (SIZE(1)), docsQosServiceClassTosOrMask OCTET STRING (SIZE(1)), docsQosServiceClassDirection IfDirection } docsQosServiceClassName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..15)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service Class Name. DOCSIS specifies that the maximum size is 15 printable ASCII characters with a terminating zero. The terminating zero is not represented in this DisplayString syntax object. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.3.4" ::= { docsQosServiceClassEntry 1 } -- docsQosServiceClassParamSetIndex { docsQosServiceClassEntry 2 } -- was removed in revision -03 docsQosServiceClassStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create or delete rows in this table." ::= { docsQosServiceClassEntry 3 } docsQosServiceClassPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetPriority." DEFVAL { 0 } ::= { docsQosServiceClassEntry 4 } docsQosServiceClassMaxTrafficRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxTrafficRate." DEFVAL { 0 } ::= { docsQosServiceClassEntry 5 } docsQosServiceClassMaxTrafficBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxTrafficBurst." DEFVAL { 1522 } ::= { docsQosServiceClassEntry 6 } docsQosServiceClassMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSEtMinReservedRate." DEFVAL { 0 } ::= { docsQosServiceClassEntry 7 } docsQosServiceClassMinReservedPkt OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMinReservedPkt." ::= { docsQosServiceClassEntry 8 } docsQosServiceClassMaxConcatBurst OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetMaxConcatBurst." DEFVAL { 0 } ::= { docsQosServiceClassEntry 9 } docsQosServiceClassNomPollInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetNomPollInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 10 } docsQosServiceClassTolPollJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetTolPollJitter." DEFVAL { 0 } ::= { docsQosServiceClassEntry 11 } docsQosServiceClassUnsolicitGrantSize OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetUnsolicitGrantSize." DEFVAL { 0 } ::= { docsQosServiceClassEntry 12 } docsQosServiceClassNomGrantInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetNomGrantInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 13 } docsQosServiceClassTolGrantJitter OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetTolGrantJitter." DEFVAL { 0 } ::= { docsQosServiceClassEntry 14 } docsQosServiceClassGrantsPerInterval OBJECT-TYPE SYNTAX Integer32 (0..127) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetGrantsPerInterval." DEFVAL { 0 } ::= { docsQosServiceClassEntry 15 } docsQosServiceClassMaxLatency OBJECT-TYPE SYNTAX Unsigned32 UNITS "microseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosParamSetClassMaxLatency." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.7.1" DEFVAL { 0 } ::= { docsQosServiceClassEntry 16 } docsQosServiceClassActiveTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowActiveTimeout." DEFVAL { 0 } ::= { docsQosServiceClassEntry 17 } docsQosServiceClassAdmittedTimeout OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowAdmittedTimeout." DEFVAL { 200 } ::= { docsQosServiceClassEntry 18 } docsQosServiceClassSchedulingType OBJECT-TYPE SYNTAX SchedulingType MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowSchedulingType." DEFVAL { bestEffort } ::= { docsQosServiceClassEntry 19 } docsQosServiceClassRequestPolicy OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowRequestPolicy." DEFVAL { '00000000'H } -- no bits are set ::= { docsQosServiceClassEntry 20 } docsQosServiceClassTosAndMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowTosAndMask." DEFVAL { 'FF'H } ::= { docsQosServiceClassEntry 21 } docsQosServiceClassTosOrMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-create STATUS current DESCRIPTION "Template for docsQosServiceFlowTosOrMask." DEFVAL { '00'H } ::= { docsQosServiceClassEntry 22 } docsQosServiceClassDirection OBJECT-TYPE SYNTAX IfDirection MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the service class template applies to upstream or downstream service flows." DEFVAL { upstream } ::= { docsQosServiceClassEntry 23 } -- -- Service Class PolicyTable -- docsQosServiceClassPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosServiceClassPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the set of Docsis-QOS Service Class Policies. This table is an adjunct to the docsDevFilterPolicy table. Entries in docsDevFilterPolicy table can point to specific rows in this table. This table permits mapping a packet to a service class name of an active service flow so long as a classifier does not exist at a higher priority. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix E.2.1" ::= { docsQosMIBObjects 9 } docsQosServiceClassPolicyEntry OBJECT-TYPE SYNTAX DocsQosServiceClassPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A service class name policy entry." INDEX { docsQosServiceClassPolicyIndex } ::= { docsQosServiceClassPolicyTable 1 } DocsQosServiceClassPolicyEntry ::= SEQUENCE { docsQosServiceClassPolicyIndex Integer32, docsQosServiceClassPolicyName DisplayString, docsQosServiceClassPolicyRulePriority Integer32, docsQosServiceClassPolicyStatus RowStatus } docsQosServiceClassPolicyIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index value to uniquely identify an entry in this table." ::= { docsQosServiceClassPolicyEntry 1 } docsQosServiceClassPolicyName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service Class Name to identify the name of the service class flow to which the packet should be directed." REFERENCE "SP-RFIv1.1-I05-000714, Appendix E.2.1" ::= { docsQosServiceClassPolicyEntry 2 } docsQosServiceClassPolicyRulePriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Service Class Policy rule priority for the entry." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.1.3.5" ::= { docsQosServiceClassPolicyEntry 3 } docsQosServiceClassPolicyStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Used to create or delete rows in this table. This object should not be deleted if it is reference by an entry in docsDevFilterPolicy. The reference should be deleted first." ::= { docsQosServiceClassPolicyEntry 4 } -- -- Payload Header Suppression(PHS) Table -- docsQosPHSTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosPHSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes set of payload header suppression entries." ::= { docsQosMIBObjects 10 } docsQosPHSEntry OBJECT-TYPE SYNTAX DocsQosPHSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A payload header suppression entry. The ifIndex is an ifType of docsCableMaclayer(127). The index docsQosServiceFlowId selects one service flow from the cable MAC layer interface. The docsQosPktClassId index matches an index of the docsQosPktClassTable. " INDEX { ifIndex, docsQosServiceFlowId, docsQosPktClassId } ::= { docsQosPHSTable 1 } DocsQosPHSEntry ::= SEQUENCE { docsQosPHSField OCTET STRING, docsQosPHSMask OCTET STRING, docsQosPHSSize Integer32, docsQosPHSVerify TruthValue, docsQosPHSIndex Integer32 } -- The object docsQosPHSIndex used as an index {docsQosPHSEntry 1} -- was changed to be a non-index column in revision -03. docsQosPHSField OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression field defines the bytes of the header which must be suppressed/restored by the sending/receiving device. The number of octets in this object should be the same as the value of docsQosPHSSize." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.1" ::= { docsQosPHSEntry 2 } docsQosPHSMask OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression mask defines the bit mask which used in combination with the docsQosPHSField defines which bytes in header must be suppressed/restored by the sending or receiving device. Each bit of this bit mask corresponds to a byte in the docsQosPHSField, with the least significant bit corresponding to first byte of the docsQosPHSField. Each bit of the bit mask specifies whether of not the corresponding byte should be suppressed in the packet. A bit value of '1' indicates that the byte should be suppressed by the sending device and restored by the receiving device. A bit value of '0' indicates that the byte should not be suppressed by the sending device or restored by the receiving device. If the bit mask does not contain a bit for each byte in the docsQosPHSField then the bit mask is extended with bit values of '1' to be the necessary length." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.3" ::= { docsQosPHSEntry 3 } docsQosPHSSize OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression size specifies the number of bytes in the header to be suppressed and restored. The value of this object must match the number of bytes in the docsQosPHSField." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.4" ::= { docsQosPHSEntry 4 } docsQosPHSVerify OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression verification value of 'true' the sender must verify docsQosPHSField is the same as what is contained in the packet to be suppressed." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.5" ::= { docsQosPHSEntry 5 } -- Removed dosQosPHSClassifierIndex {docsQosPHSEntry 6} -- in revision -03. docsQosPHSIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Payload header suppression index uniquely references the PHS rule for a given service flow." REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.10.2" ::= { docsQosPHSEntry 7 } -- -- docsQosCmtsMacToSrvFlowTable (CMTS Only) -- docsQosCmtsMacToSrvFlowTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsQosCmtsMacToSrvFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provide for referencing the service flows associated with a particular cable modem. This allows for indexing into other docsQos tables that are indexed by docsQosServiceFlowId and ifIndex." ::= { docsQosMIBObjects 11 } docsQosCmtsMacToSrvFlowEntry OBJECT-TYPE SYNTAX DocsQosCmtsMacToSrvFlowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created by CMTS for each service flow connected to this CMTS." INDEX { docsQosCmtsCmMac, docsQosCmtsServiceFlowId } ::= { docsQosCmtsMacToSrvFlowTable 1 } DocsQosCmtsMacToSrvFlowEntry ::= SEQUENCE { docsQosCmtsCmMac MacAddress, docsQosCmtsServiceFlowId Unsigned32, docsQosCmtsIfIndex InterfaceIndex } docsQosCmtsCmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address for the referenced CM." ::= { docsQosCmtsMacToSrvFlowEntry 1 } docsQosCmtsServiceFlowId OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index assigned to a service flow by CMTS." ::= { docsQosCmtsMacToSrvFlowEntry 2 } docsQosCmtsIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of ifType docsCableMacLayter(127) on the CMTS that is connected to the Cable Modem." ::= { docsQosCmtsMacToSrvFlowEntry 3 } -- -- Placeholder for notifications/traps. -- docsQosNotification OBJECT IDENTIFIER ::= { docsQosMIB 2 } -- -- Conformance definitions -- docsQosConformance OBJECT IDENTIFIER ::= { docsQosMIB 3 } docsQosGroups OBJECT IDENTIFIER ::= { docsQosConformance 1 } docsQosCompliances OBJECT IDENTIFIER ::= { docsQosConformance 2 } docsQosCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for MCNS Cable Modems and Cable Modem Termination Systems that implement DOCSIS Service Flows." MODULE -- docsQosMIB MANDATORY-GROUPS { docsQosBaseGroup } GROUP docsQosCmtsGroup DESCRIPTION "This group is mandatory for only Cable Modem Termination Systems (CMTS) and not implemented for Cable Modems." GROUP docsQosParamSetGroup DESCRIPTION "This group is mandatory for Cable Modem Termination Systems (CMTS) and Cable Modems. Cable modems only implement objects in this group as read-only." GROUP docsQosSrvClassPolicyGroup DESCRIPTION "This group is optional for Cable Modem Termination Systems (CMTS) and Cable Modems. This group only needs to be implement if policy based service flow classification is implemented. See docsDevPolicyTable in DOCS-CABLE-DEVICE-MIB for more details. " GROUP docsQosServiceClassGroup DESCRIPTION "The docsQosServiceClassTable group of objects. " OBJECT docsQosPktClassPkts DESCRIPTION "This object only needs to be implemented in entries that are classifying packets and not policing packets." ::= { docsQosCompliances 1 } docsQosBaseGroup OBJECT-GROUP OBJECTS { docsQosPktClassDirection, docsQosPktClassPriority, docsQosPktClassIpTosLow, docsQosPktClassIpTosHigh, docsQosPktClassIpTosMask, docsQosPktClassIpProtocol, docsQosPktClassIpSourceAddr, docsQosPktClassIpSourceMask, docsQosPktClassIpDestAddr, docsQosPktClassIpDestMask, docsQosPktClassSourcePortStart, docsQosPktClassSourcePortEnd, docsQosPktClassDestPortStart, docsQosPktClassDestPortEnd, docsQosPktClassDestMacAddr, docsQosPktClassDestMacMask, docsQosPktClassSourceMacAddr, docsQosPktClassEnetProtocolType, docsQosPktClassEnetProtocol, docsQosPktClassUserPriLow, docsQosPktClassUserPriHigh, docsQosPktClassVlanId, docsQosPktClassState, docsQosPktClassPkts, docsQosPktClassBitMap, docsQosServiceFlowSID, docsQosServiceFlowDirection, docsQosServiceFlowPrimary, docsQosServiceFlowPkts, -- not sure if CM should implement docsQosServiceFlowOctets, docsQosServiceFlowTimeCreated, docsQosServiceFlowTimeActive, docsQosServiceFlowPHSUnknowns, docsQosServiceFlowPolicedDropPkts, docsQosServiceFlowPolicedDelayPkts, docsQosDSAReqs, docsQosDSARsps, docsQosDSAAcks, docsQosDSCReqs, docsQosDSCRsps, docsQosDSCAcks, docsQosDSDReqs, docsQosDSDRsps, docsQosDynamicAdds, docsQosDynamicAddFails, docsQosDynamicChanges, docsQosDynamicChangeFails, docsQosDynamicDeletes, docsQosDynamicDeleteFails, docsQosDCCReqs, docsQosDCCRsps, docsQosDCCAcks, docsQosDCCs, docsQosDCCFails, docsQosPHSField, docsQosPHSMask, docsQosPHSSize, docsQosPHSVerify, docsQosPHSIndex } STATUS current DESCRIPTION "Group of objects implemented in both Cable Modems and Cable Modem Termination Systems." ::= { docsQosGroups 1 } docsQosParamSetGroup OBJECT-GROUP OBJECTS { docsQosParamSetServiceClassName, docsQosParamSetPriority, docsQosParamSetMaxTrafficRate, docsQosParamSetMaxTrafficBurst, docsQosParamSetMinReservedRate, docsQosParamSetMinReservedPkt, docsQosParamSetActiveTimeout, docsQosParamSetAdmittedTimeout, docsQosParamSetMaxConcatBurst, docsQosParamSetSchedulingType, docsQosParamSetNomPollInterval, docsQosParamSetTolPollJitter, docsQosParamSetUnsolicitGrantSize, docsQosParamSetNomGrantInterval, docsQosParamSetTolGrantJitter, docsQosParamSetGrantsPerInterval, docsQosParamSetTosAndMask, docsQosParamSetTosOrMask, docsQosParamSetMaxLatency, docsQosParamSetRequestPolicyOct, docsQosParamSetBitMap } STATUS current DESCRIPTION "Group of objects implemenent in both Cable Modems and Cable Modem Termination Systems for QOS parameter sets." ::= { docsQosGroups 2 } docsQosCmtsGroup OBJECT-GROUP OBJECTS { docsQosUpstreamFragments, docsQosUpstreamFragDiscards, docsQosUpstreamConcatBursts, docsQosServiceFlowLogIfIndex, docsQosServiceFlowLogSFID, docsQosServiceFlowLogCmMac, docsQosServiceFlowLogPkts, docsQosServiceFlowLogOctets, docsQosServiceFlowLogTimeDeleted, docsQosServiceFlowLogTimeCreated, docsQosServiceFlowLogTimeActive, docsQosServiceFlowLogDirection, docsQosServiceFlowLogPrimary, docsQosServiceFlowLogServiceClassName, docsQosServiceFlowLogPolicedDropPkts, docsQosServiceFlowLogPolicedDelayPkts, docsQosServiceFlowLogControl, docsQosCmtsIfIndex -- docsQosCmtsMacToSrvFlowTable required } STATUS current DESCRIPTION "Mandatory group of objects implemented only in the CMTS." ::= { docsQosGroups 3 } docsQosSrvClassPolicyGroup OBJECT-GROUP OBJECTS { docsQosServiceClassPolicyName, docsQosServiceClassPolicyRulePriority, docsQosServiceClassPolicyStatus } STATUS current DESCRIPTION "Group of objects implemented in both Cable Modems and Cable Modem Termination Systems when supporting policy based service flows." ::= { docsQosGroups 4 } docsQosServiceClassGroup OBJECT-GROUP OBJECTS { docsQosServiceClassStatus, docsQosServiceClassPriority, docsQosServiceClassMaxTrafficRate, docsQosServiceClassMaxTrafficBurst, docsQosServiceClassMinReservedRate, docsQosServiceClassMinReservedPkt, docsQosServiceClassMaxConcatBurst, docsQosServiceClassNomPollInterval, docsQosServiceClassTolPollJitter, docsQosServiceClassUnsolicitGrantSize, docsQosServiceClassNomGrantInterval, docsQosServiceClassTolGrantJitter, docsQosServiceClassGrantsPerInterval, docsQosServiceClassMaxLatency, docsQosServiceClassActiveTimeout, docsQosServiceClassAdmittedTimeout, docsQosServiceClassSchedulingType, docsQosServiceClassRequestPolicy, docsQosServiceClassTosAndMask, docsQosServiceClassTosOrMask, docsQosServiceClassDirection } STATUS current DESCRIPTION "The docsQosServiceClassTable objects. If a CMTS implements expansion of Service Class Names in a QOS Parameter Set, this group is mandatory on the CMTS. If the CMTS does not support Service Class Names, this group may be unimplemented in the CMTS. This group is not implemented on the CM. " ::= { docsQosGroups 5 } END