-- extracted from draft-ietf-msdp-mib-07.txt -- at Fri May 30 06:13:13 2003 DRAFT-MSDP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Counter32, Gauge32, TimeTicks, Integer32 FROM SNMPv2-SMI RowStatus, TruthValue, TimeStamp, DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF InterfaceIndexOrZero FROM IF-MIB InetAddressType, InetAddress, InetPortNumber, InetAddressPrefixLength FROM INET-ADDRESS-MIB; msdpMIB MODULE-IDENTITY LAST-UPDATED "200103010000Z" ORGANIZATION "IETF MSDP Working Group" CONTACT-INFO "Bill Fenner 75 Willow Road Menlo Park, CA 94025 Phone: +1 650 867 6073 E-mail: fenner@research.att.com Dave Thaler One Microsoft Way Redmond, WA 98052 Phone: +1 425 703 8835 Email: dthaler@microsoft.com" DESCRIPTION "An experimental MIB module for MSDP Management." ::= { experimental 92 } msdp OBJECT IDENTIFIER ::= { msdpMIB 1 } msdpScalars OBJECT IDENTIFIER ::= { msdp 1 } msdpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The state of MSDP on this MSDP speaker - globally enabled or disabled." ::= { msdpScalars 1 } msdpCacheLifetime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "The lifetime given to SA cache entries when created or refreshed. This is the [SA-State-Period] in the MSDP spec. A value of 0 means no SA caching is done by this MSDP speaker." ::= { msdpScalars 2 } msdpNumSACacheEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of entries in the SA Cache table." ::= { msdpScalars 3 } msdpSAHoldDownPeriod OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds in the MSDP SA Hold-down period." ::= { msdpScalars 4 } msdpSAStatePeriod OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds in the MSDP SA State period." ::= { msdpScalars 5 } msdpRPAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of the RP address used when sourcing MSDP SA messages. May be unknown(0) on non-RP's or when the PIM RP address is correct." ::= { msdpScalars 6 } msdpRPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The RP address used when sourcing MSDP SA messages. May be a zero length string on non-RP's or when the PIM RP address is correct." ::= { msdpScalars 7 } --- --- The MSDP Requests table --- msdpRequestsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpRequestsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing group ranges and MSDP peers used when deciding where to send an SA Request message when required. If SA Requests are not enabled, this table may be empty. In order to choose a peer to whom to send an SA Request for a given group G, the subset of entries in this table whose (msdpRequestsPeerType, msdpRequestsPeer) tuple represents a peer whose msdpPeerState is established are examined. The set is further reduced by examining only those entries for which msdpPeerRequestsGroupAddressType equals the address type of G, and the entries with the highest value of msdpRequestsGroupPrefix are considered, where the group G falls within the range described by the combination of msdpRequestsGroup and msdpRequestsGroupPrefix. (This sequence is commonly known as a 'longest-match' lookup.) Finally, if multiple entries remain, the entry with the lowest value of msdpRequestsPriority is chosen. The SA Request message is sent to the peer described by this row." ::= { msdp 2 } msdpRequestsEntry OBJECT-TYPE SYNTAX MsdpRequestsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a group range used when deciding where to send an SA Request message." INDEX { msdpRequestsGroupAddressType, msdpRequestsGroupAddress, msdpRequestsGroupPrefix, msdpRequestsPriority } ::= { msdpRequestsTable 1 } MsdpRequestsEntry ::= SEQUENCE { msdpRequestsGroupAddressType InetAddressType, msdpRequestsGroupAddress InetAddress, msdpRequestsGroupPrefix InetAddressPrefixLength, msdpRequestsPriority Integer32, msdpRequestsPeerType InetAddressType, msdpRequestsPeer InetAddress, msdpRequestsStatus RowStatus } msdpRequestsGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of msdpRequestsGroupAddress. Only ipv4 and ipv6 addresses are expected." ::= { msdpRequestsEntry 1 } msdpRequestsGroupAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address that, when combined with the prefix length in this entry, represents the group range to which this row applies." ::= { msdpRequestsEntry 2 } msdpRequestsGroupPrefix OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "The prefix length that, when combined with the group address in this entry, represents the group range to which this row applies." ::= { msdpRequestsEntry 3 } msdpRequestsPriority OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The priority of this peer. The peer with the lowest priority value with which we have an active peering session (i.e. msdpPeerState = established) is the peer to whom SA requests for groups matching the entry's group range will be sent." ::= { msdpRequestsEntry 4 } msdpRequestsPeerType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The address type of msdpRequestsPeer." ::= { msdpRequestsEntry 5 } msdpRequestsPeer OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The peer to which MSDP SA Requests for groups matching this entry's group range will be sent. This object combined with msdpRequestsPeerType must match the INDEX of a row in the msdpPeerTable, and to be considered, this peer's msdpPeerState must be established." ::= { msdpRequestsEntry 6 } msdpRequestsStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which new rows may be added to the table or old rows may be deleted." ::= { msdpRequestsEntry 7 } --- --- The MSDP Peer table --- msdpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the MSDP speaker's peers." ::= { msdp 3 } msdpPeerEntry OBJECT-TYPE SYNTAX MsdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an MSDP peer." INDEX { msdpPeerAddressType, msdpPeerRemoteAddress } ::= { msdpPeerTable 1 } MsdpPeerEntry ::= SEQUENCE { msdpPeerAddressType InetAddressType, msdpPeerRemoteAddress InetAddress, msdpPeerState INTEGER, msdpPeerRPFFailures Counter32, msdpPeerInSAs Counter32, msdpPeerOutSAs Counter32, msdpPeerInSARequests Counter32, msdpPeerOutSARequests Counter32, msdpPeerInSAResponses Counter32, msdpPeerOutSAResponses Counter32, msdpPeerInControlMessages Counter32, msdpPeerOutControlMessages Counter32, msdpPeerInDataPackets Counter32, msdpPeerOutDataPackets Counter32, msdpPeerFsmEstablishedTransitions Counter32, msdpPeerFsmEstablishedTime TimeStamp, msdpPeerInMessageTime TimeStamp, msdpPeerLocalAddress InetAddress, msdpPeerConnectRetryInterval Integer32, msdpPeerHoldTimeConfigured Integer32, msdpPeerKeepAliveConfigured Integer32, msdpPeerDataTtl Integer32, msdpPeerProcessRequestsFrom TruthValue, msdpPeerStatus RowStatus, msdpPeerRemotePort InetPortNumber, msdpPeerLocalPort InetPortNumber, msdpPeerEncapsulationType INTEGER, msdpPeerConnectionAttempts Counter32, msdpPeerInNotifications Counter32, msdpPeerOutNotifications Counter32, msdpPeerLastError OCTET STRING, msdpPeerIfIndex InterfaceIndexOrZero, msdpPeerDiscontinuityTime TimeStamp } msdpPeerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of msdpPeerRemoteAddress and msdpPeerLocalAddress." ::= { msdpPeerEntry 1 } msdpPeerRemoteAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of the remote MSDP peer." ::= { msdpPeerEntry 2 } msdpPeerState OBJECT-TYPE SYNTAX INTEGER { inactive(1), listen(2), connecting(3), established(4), disabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the MSDP TCP connection with this peer." ::= { msdpPeerEntry 3 } msdpPeerRPFFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SA messages received from this peer which failed the Peer-RPF check. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 4 } msdpPeerInSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 5 } msdpPeerOutSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages transmitted on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 6 } msdpPeerInSARequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA-Request messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 7 } msdpPeerOutSARequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA-Request messages transmitted on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 8 } msdpPeerInSAResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA-Response messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 9 } msdpPeerOutSAResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA Response messages transmitted on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 10 } msdpPeerInControlMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MSDP messages received on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 11 } msdpPeerOutControlMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MSDP messages transmitted on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 12 } msdpPeerInDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of encapsulated data packets received from this peer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 13 } msdpPeerOutDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of encapsulated data packets sent to this peer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 14 } msdpPeerFsmEstablishedTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the MSDP FSM transitioned into the established state." ::= { msdpPeerEntry 15 } msdpPeerFsmEstablishedTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This timestamp is set to the value of sysUpTime when a peer transitions into or out of the Established state. It is set to zero when the MSDP speaker is booted." ::= { msdpPeerEntry 16 } msdpPeerInMessageTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime value when the last MSDP message was received from the peer. It is set to zero when the MSDP speaker is booted." ::= { msdpPeerEntry 17 } msdpPeerLocalAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The local IP address of this entry's MSDP connection." ::= { msdpPeerEntry 18 } msdpPeerConnectRetryInterval OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval in seconds for the [ConnectRetry-period] for this peer." REFERENCE "draft-ietf-msdp-spec-20.txt section 8.7" DEFVAL { 120 } ::= { msdpPeerEntry 19 } msdpPeerHoldTimeConfigured OBJECT-TYPE SYNTAX Integer32 (0|3..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval in seconds for the [HoldTime-Period] configured for this MSDP speaker with this peer." REFERENCE "draft-ietf-msdp-spec-20.txt section 8.5" DEFVAL { 90 } ::= { msdpPeerEntry 20 } msdpPeerKeepAliveConfigured OBJECT-TYPE SYNTAX Integer32 (0|1..21845) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval in seconds for the [KeepAlive-Period] configured for this MSDP speaker with this peer. A reasonable maximum value for this timer would be configured to be one third of that of msdpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the MSDP connection has been established." REFERENCE "draft-ietf-msdp-spec-20.txt section 8.6" DEFVAL { 30 } ::= { msdpPeerEntry 21 } msdpPeerDataTtl OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum TTL a packet is required to have before it may be forwarded using SA encapsulation to this peer." ::= { msdpPeerEntry 22 } msdpPeerProcessRequestsFrom OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether or not to process MSDP SA Request messages from this peer. If True(1), MSDP SA Request messages from this peer are processed and replied to (if appropriate) with SA Response messages. If False(2), MSDP SA Request messages from this peer are silently ignored. It defaults to False when msdpCacheLifetime is 0 and True when msdpCacheLifetime is non-0." ::= { msdpPeerEntry 23 } msdpPeerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The RowStatus object by which peers can be added and deleted. A transition to 'active' will cause the MSDP Start Event to be generated. A transition out of the 'active' state will cause the MSDP Stop Event to be generated. Care should be used in providing write access to this object without adequate authentication." ::= { msdpPeerEntry 24 } msdpPeerRemotePort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The remote port for the TCP connection between the MSDP peers." ::= { msdpPeerEntry 25 } msdpPeerLocalPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The local port for the TCP connection between the MSDP peers." ::= { msdpPeerEntry 26 } msdpPeerEncapsulationType OBJECT-TYPE SYNTAX INTEGER { none(0), tcp(1), udp(2), gre(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation in use when encapsulating data in SA messages to this peer." DEFVAL { gre } ::= { msdpPeerEntry 27 } msdpPeerConnectionAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the state machine has transitioned from inactive to connecting." ::= { msdpPeerEntry 28 } msdpPeerInNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP Notification messages received from this peer." ::= { msdpPeerEntry 29 } msdpPeerOutNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP Notification messages transmitted to this peer." ::= { msdpPeerEntry 30 } msdpPeerLastError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code and subcode received via Notification from this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the O-bit and error code, and the second byte contains the subcode." REFERENCE "draft-ietf-msdp-spec-20.txt section 16.2.5 and 17" DEFVAL { '0000'h } ::= { msdpPeerEntry 31 } msdpPeerIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the MSDP encapsulation interface for this peer, or zero if the encapsulation is not represented by an interface in the ifTable." DEFVAL { 0 } ::= { msdpPeerEntry 32 } msdpPeerDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which one or more of this entry's counters suffered a discontinuity. See the DESCRIPTION of each object to see if it is expected to have discontinuities. These discontinuities may occur at peer connection establishment. If no such discontinuities have occurred since the last reinitialization of the local management subsystem, then this object contains a zero value." ::= { msdpPeerEntry 33 } --- --- The MSDP Source-Active Cache table --- msdpSACacheTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpSACacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the MSDP SA advertisements currently in the MSDP speaker's cache." ::= { msdp 4 } msdpSACacheEntry OBJECT-TYPE SYNTAX MsdpSACacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an MSDP SA advertisement. The INDEX to this table includes msdpSACacheOriginRP for diagnosing incorrect MSDP advertisements; normally a Group and Source pair would be unique." INDEX { msdpSACacheAddrType, msdpSACacheGroupAddr, msdpSACacheSourceAddr, msdpSACacheSourcePrefix, msdpSACacheOriginRP } ::= { msdpSACacheTable 1 } MsdpSACacheEntry ::= SEQUENCE { msdpSACacheAddrType InetAddressType, msdpSACacheGroupAddr InetAddress, msdpSACacheSourceAddr InetAddress, msdpSACacheSourcePrefix InetAddressPrefixLength, msdpSACacheOriginRP InetAddress, msdpSACachePeerLearnedFrom InetAddress, msdpSACacheRPFPeer InetAddress, msdpSACacheInSAs Counter32, msdpSACacheInDataPackets Counter32, msdpSACacheUpTime TimeTicks, msdpSACacheExpiryTime TimeTicks, msdpSACacheStatus RowStatus } msdpSACacheAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of all of the InetAddress object in this entry." ::= { msdpSACacheEntry 1 } msdpSACacheGroupAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of the SA Cache entry." ::= { msdpSACacheEntry 2 } msdpSACacheSourceAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source address of the SA Cache entry." ::= { msdpSACacheEntry 3 } msdpSACacheSourcePrefix OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Sprefix len of this SA Cache entry." ::= { msdpSACacheEntry 4 } msdpSACacheOriginRP OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RP of the SA Cache entry. This field is in the INDEX in order to catch multiple RP's advertising the same source and group." ::= { msdpSACacheEntry 5 } msdpSACachePeerLearnedFrom OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The peer from which this SA Cache entry was last accepted. This address must correspond to the msdpPeerRemoteAddress value for a row in the MSDP Peer Table." ::= { msdpSACacheEntry 6 } msdpSACacheRPFPeer OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The peer from which an SA message corresponding to this cache entry would be accepted (i.e. the RPF peer for msdpSACacheOriginRP). This may be different than msdpSACachePeerLearnedFrom if this entry was created by an MSDP SA-Response. This address must correspond to the msdpPeerRemoteAddress value for a row in the MSDP Peer Table, or may be 0.0.0.0 if no RPF peer exists." ::= { msdpSACacheEntry 7 } msdpSACacheInSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages received relevant to this cache entry. This object must be initialized to zero when creating a cache entry." ::= { msdpSACacheEntry 8 } msdpSACacheInDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP encapsulated data packets received relevant to this cache entry. This object must be initialized to zero when creating a cache entry." ::= { msdpSACacheEntry 9 } msdpSACacheUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since this entry was placed in the SA cache." ::= { msdpSACacheEntry 10 } msdpSACacheExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before this entry will expire from the SA cache." ::= { msdpSACacheEntry 11 } msdpSACacheStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The status of this row in the table. The only allowable actions are to retrieve the status, which will be `active', or to set the status to `destroy' in order to remove this entry from the cache." ::= { msdpSACacheEntry 12 } -- -- MSDP Mesh Group Membership table -- msdpMeshGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpMeshGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing MSDP Mesh Group configuration." ::= { msdp 5 } msdpMeshGroupEntry OBJECT-TYPE SYNTAX MsdpMeshGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) repesenting a peer in an MSDP Mesh Group." INDEX { msdpMeshGroupName, msdpMeshGroupPeerAddressType, msdpMeshGroupPeerAddress } ::= { msdpMeshGroupTable 1 } MsdpMeshGroupEntry ::= SEQUENCE { msdpMeshGroupName DisplayString, msdpMeshGroupPeerAddressType InetAddressType, msdpMeshGroupPeerAddress InetAddress, msdpMeshGroupStatus RowStatus } msdpMeshGroupName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the mesh group." ::= { msdpMeshGroupEntry 1 } msdpMeshGroupPeerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of msdpMeshGroupPeerAddress." ::= { msdpMeshGroupEntry 2 } msdpMeshGroupPeerAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(1..36)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A peer address that is a member of the mesh group with name msdpMeshGroupName. The tuple (msdpMeshGroupPeerAddressType, msdpMeshGroupPeerAddress) must match a row in the msdpPeerTable." ::= { msdpMeshGroupEntry 3 } msdpMeshGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This entry's status, by which new entries may be added to the table and old entries deleted." ::= { msdpMeshGroupEntry 4 } -- Traps msdpTraps OBJECT IDENTIFIER ::= { msdp 0 } msdpEstablished NOTIFICATION-TYPE OBJECTS { msdpPeerFsmEstablishedTransitions } STATUS current DESCRIPTION "The MSDP Established event is generated when the MSDP FSM enters the ESTABLISHED state." ::= { msdpTraps 1 } msdpBackwardTransition NOTIFICATION-TYPE OBJECTS { msdpPeerState } STATUS current DESCRIPTION "The MSDPBackwardTransition Event is generated when the MSDP FSM moves from a higher numbered state to a lower numbered state." ::= { msdpTraps 2 } -- conformance information msdpMIBConformance OBJECT IDENTIFIER ::= { msdp 6 } msdpMIBCompliances OBJECT IDENTIFIER ::= { msdpMIBConformance 1 } msdpMIBGroups OBJECT IDENTIFIER ::= { msdpMIBConformance 2 } -- compliance statements msdpMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the MSDP MIB." MODULE -- this module MANDATORY-GROUPS { msdpMIBGlobalsGroup, msdpMIBPeerGroup, msdpMIBNotificationGroup } GROUP msdpMIBEncapsulationGroup DESCRIPTION "This group is mandatory if MSDP encapsulation interfaces are not given their own interface index numbers." GROUP msdpMIBSACacheGroup DESCRIPTION "This group is mandatory if the MSDP speaker has the ability to cache SA messages." GROUP msdpMIBRequestsGroup DESCRIPTION "This group is mandatory if the MSDP speaker has the ability to send SA-Request messages and parse SA-Response messages." GROUP msdpMIBRPGroup DESCRIPTION "This group is mandatory if the MSDP speaker sources (as opposed to forwards) MSDP messages." GROUP msdpMIBMeshGroupGroup DESCRIPTION "This group is mandatory if the MSDP speaker can participate in MSDP Mesh Groups." ::= { msdpMIBCompliances 1 } -- units of conformance msdpMIBGlobalsGroup OBJECT-GROUP OBJECTS { msdpEnabled } STATUS current DESCRIPTION "A collection of objects providing information on global MSDP state." ::= { msdpMIBGroups 1 } msdpMIBPeerGroup OBJECT-GROUP OBJECTS { msdpPeerRPFFailures, msdpPeerState, msdpPeerInSAs, msdpPeerOutSAs, msdpPeerInSARequests, msdpPeerOutSARequests, msdpPeerInSAResponses, msdpPeerOutSAResponses, msdpPeerInNotifications, msdpPeerOutNotifications, msdpPeerInControlMessages, msdpPeerOutControlMessages, msdpPeerFsmEstablishedTransitions, msdpPeerFsmEstablishedTime, msdpPeerLocalAddress, msdpPeerRemotePort, msdpPeerLocalPort, msdpPeerConnectRetryInterval, msdpPeerHoldTimeConfigured, msdpPeerKeepAliveConfigured, msdpPeerInMessageTime, msdpPeerProcessRequestsFrom, msdpPeerConnectionAttempts, msdpPeerLastError, msdpPeerIfIndex, msdpPeerStatus, msdpPeerDiscontinuityTime } STATUS current DESCRIPTION "A collection of objects for managing MSDP peers." ::= { msdpMIBGroups 2 } msdpMIBEncapsulationGroup OBJECT-GROUP OBJECTS { msdpPeerInDataPackets, msdpPeerOutDataPackets, msdpPeerDataTtl, msdpPeerEncapsulationType } STATUS current DESCRIPTION "A collection of objects for managing encapsulations if the MSDP encapsulation interfaces are not given interface indices." ::= { msdpMIBGroups 3 } msdpMIBSACacheGroup OBJECT-GROUP OBJECTS { msdpCacheLifetime, msdpNumSACacheEntries, msdpSAHoldDownPeriod, msdpSAStatePeriod, msdpSACachePeerLearnedFrom, msdpSACacheRPFPeer, msdpSACacheInSAs, msdpSACacheInDataPackets, msdpSACacheUpTime, msdpSACacheExpiryTime, msdpSACacheStatus } STATUS current DESCRIPTION "A collection of objects for managing MSDP SA cache entries." ::= { msdpMIBGroups 4 } msdpMIBNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { msdpEstablished, msdpBackwardTransition } STATUS current DESCRIPTION "A collection of notifications for signaling changes in MSDP peer relationships." ::= { msdpMIBGroups 5 } msdpMIBRequestsGroup OBJECT-GROUP OBJECTS { msdpRequestsPeerType, msdpRequestsPeer, msdpRequestsStatus } STATUS current DESCRIPTION "A collection of objects for managing MSDP Request transmission." ::= { msdpMIBGroups 6 } msdpMIBRPGroup OBJECT-GROUP OBJECTS { msdpRPAddressType, msdpRPAddress } STATUS current DESCRIPTION "A collection of objects for MSDP speakers that source MSDP messages." ::= { msdpMIBGroups 7 } msdpMIBMeshGroupGroup OBJECT-GROUP OBJECTS { msdpMeshGroupStatus } STATUS current DESCRIPTION "A collection of objects for MSDP speakers that can participate in MSDP mesh groups." ::= { msdpMIBGroups 8 } END --