-- extracted from draft-bierman-dsmon-mib-01.txt -- at Mon Nov 15 17:11:09 1999 DSMON-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Gauge32, Counter64, experimental FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF RowStatus, TimeStamp, TEXTUAL-CONVENTION FROM SNMPv2-TC OwnerString FROM IF-MIB protocolDirLocalIndex, LastCreateTime, DataSource, ZeroBasedCounter32, TimeFilter FROM RMON2-MIB ZeroBasedCounter64 FROM HC-RMON-MIB; dsMonMIB MODULE-IDENTITY LAST-UPDATED "9906100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Andy Bierman Cisco Systems, Inc. Postal: 170 West Tasman Drive San Jose, CA USA 95134 Tel: +1 408 527-3711 E-mail: abierman@cisco.com" DESCRIPTION "This module defines Remote Monitoring MIB extensions for Differentiated Services enabled networks." ::= { experimental 999999 } dsMonObjects OBJECT IDENTIFIER ::= { dsMonMIB 1 } dsMonNotifications OBJECT IDENTIFIER ::= { dsMonMIB 2 } dsMonConformance OBJECT IDENTIFIER ::= { dsMonMIB 3 } dsStatObjects OBJECT IDENTIFIER ::= { dsMonObjects 1 } dsPdistObjects OBJECT IDENTIFIER ::= { dsMonObjects 2 } dsHostObjects OBJECT IDENTIFIER ::= { dsMonObjects 3 } -- -- Extensions to the RMON-2 MIB for Differentiated Services -- Monitoring -- -- In order to maintain the RMON 'look-and-feel', some of -- the text from the RMON-2 and HC-RMON MIBs by -- Steve Waldbusser have been used in this MIB. -- -- -- Textual Convention to define a DSCP for -- monitoring purposes -- DSCodePoint ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This TC describes an object which identifies the Differentiated Services Codepoint (DSCP) value in an IPv4 or IPv6 packet header." REFERENCE "Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers [RFC2474]." SYNTAX Integer32 (0..63) -- *********************************************************** -- * * -- * P E R - D A T A S O U C E C O L L E C T I O N S * -- * * -- *********************************************************** -- -- DSCP Per-DataSource Statistics Control Table -- dsStatsControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DsStatsControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Controls the setup of per-data source per-DSCP distribution statistics." ::= { dsStatObjects 1 } dsStatsControlEntry OBJECT-TYPE SYNTAX DsStatsControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsStatsControlTable. Entries are created and deleted from this table by management action only, using the dsStatsControlStatus RowStatus object. Activation of a control row in this table will cause an associated dsStatsTable to be created and maintained by the agent." INDEX { dsStatsControlIndex } ::= { dsStatsControlTable 1 } DsStatsControlEntry ::= SEQUENCE { dsStatsControlIndex Integer32, dsStatsControlDataSource DataSource, dsStatsControlDroppedFrames Counter32, dsStatsControlCreateTime LastCreateTime, dsStatsControlOwner OwnerString, dsStatsControlStatus RowStatus } dsStatsControlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary and unique index for this dsStatsControlEntry." ::= { dsStatsControlEntry 1 } dsStatsControlDataSource OBJECT-TYPE SYNTAX DataSource MAX-ACCESS read-create STATUS current DESCRIPTION "The source of data for the this per-protocol DSCP distribution. The statistics in this group reflect all IPv4 and IPv6 packets on the local network segment attached to the identified interface. This object may not be modified if the associated dsStatsControlStatus object is equal to active(1)." ::= { dsStatsControlEntry 2 } dsStatsControlDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped." ::= { dsStatsControlEntry 3 } dsStatsControlCreateTime OBJECT-TYPE SYNTAX LastCreateTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls." ::= { dsStatsControlEntry 4 } dsStatsControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { dsStatsControlEntry 5 } dsStatsControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the dsStatsTable shall be deleted." ::= { dsStatsControlEntry 6 } -- -- DSCP Per-DataSource Statistics Table -- dsStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DsStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information on Per Protocol DSCP usage. The following table defines per-DSCP statistics for full and/or half-duplex links as well as high capacity links. For half-duplex links, or full-duplex-capable links operating in half-duplex mode, the dsStatsIn* objects shall be used and the dsStatsOut* objects will not increment. For full-duplex links, the dsOut* objects will be present. Whenever possible, the probe should count packets moving away from the closest terminating equipment as output packets. Failing that, the probe should count packets moving away from the DTE as output packets." ::= { dsStatObjects 2 } dsStatsEntry OBJECT-TYPE SYNTAX DsStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information on Differentiated Services DSCP usage, containing inbound and outbound packet and octet counters for each DSCP configured for collection. The dsStatsControlIndex value in the index identifies the dsStatsControlEntry on whose behalf this entry was created. Only entries with non-zero statistics will be returned by the agent, in order to reduce the amount of polling required to retrieve data from this table. That is, an entry will be created when a packet with the indicated DSCP value is detected by the agent. Note that only protocols which are encapsulated in IPv4 or IPv6 packets will be counted in this table. An example of the indexing of this entry is dsStatsOutPkts.1.16" INDEX { dsStatsControlIndex, dsStatsDsCodept } ::= { dsStatsTable 1 } DsStatsEntry ::= SEQUENCE { dsStatsDsCodept DSCodePoint, dsStatsInPkts ZeroBasedCounter32, dsStatsInOctets ZeroBasedCounter32, dsStatsInOvflPkts ZeroBasedCounter32, dsStatsInOvflOctets ZeroBasedCounter32, dsStatsInHCPkts ZeroBasedCounter64, dsStatsInHCOctets ZeroBasedCounter64, dsStatsOutPkts ZeroBasedCounter32, dsStatsOutOctets ZeroBasedCounter32, dsStatsOutOvflPkts ZeroBasedCounter32, dsStatsOutOvflOctets ZeroBasedCounter32, dsStatsOutHCPkts ZeroBasedCounter64, dsStatsOutHCOctets ZeroBasedCounter64 } dsStatsDsCodept OBJECT-TYPE SYNTAX DSCodePoint MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSCP value associated with the aggregated statistics for a particular data source." ::= { dsStatsEntry 1 } dsStatsInPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets using a particular DSCP value, received on a half-duplex link or on the inbound connection of a full-duplex link." ::= { dsStatsEntry 2 } dsStatsInOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets in packets, using a particular DSCP value, received on a half-duplex link or on the inbound connection of a full-duplex link." ::= { dsStatsEntry 3 } dsStatsInOvflPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsStatsInPkts counter has overflowed. Note that this object will only be instantiated if the associated dsStatsInHCPkts object is also instantiated for a particular dataSource." ::= { dsStatsEntry 4 } dsStatsInOvflOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsStatsInOctets counter has overflowed. Note that this object will only be instantiated if the associated dsStatsInHCOctets object is also instantiated for a particular dataSource." ::= { dsStatsEntry 5 } dsStatsInHCPkts OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsStatsInPkts object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsStatsEntry 6 } dsStatsInHCOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsStatsInOctets object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsStatsEntry 7 } dsStatsOutPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets using a particular DSCP value, received on a full-duplex link in the direction of the network." ::= { dsStatsEntry 8 } dsStatsOutOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets in packets, using a particular DSCP value, received on a full-duplex link in the direction of the network." ::= { dsStatsEntry 9 } dsStatsOutOvflPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsStatsOutPkts counter has overflowed. Note that this object will only be instantiated if the associated dsStatsOutHCPkts object is also instantiated for a particular dataSource." ::= { dsStatsEntry 10 } dsStatsOutOvflOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsStatsOutOctets counter has overflowed. Note that this object will only be instantiated if the associated dsStatsOutHCOctets object is also instantiated for a particular dataSource." ::= { dsStatsEntry 11 } dsStatsOutHCPkts OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsStatsOutPkts object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsStatsEntry 12 } dsStatsOutHCOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsStatsOutOctets object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsStatsEntry 13 } -- *********************************************************** -- * * -- * P E R - P R O T O C O L C O L L E C T I O N S * -- * * -- *********************************************************** -- -- DSCP Per-Protocol Statistics Control Table -- dsPdistControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DsPdistControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Controls the setup of per-protocol per-DSCP distribution statistics." ::= { dsPdistObjects 1 } dsPdistControlEntry OBJECT-TYPE SYNTAX DsPdistControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsPdistControlTable. Entries are created and deleted from this table by management action only, using the dsPdistControlStatus RowStatus object. Activation of a control row in this table will cause an associated dsPdistStatsTable to be created and maintained by the agent." INDEX { dsPdistControlIndex } ::= { dsPdistControlTable 1 } DsPdistControlEntry ::= SEQUENCE { dsPdistControlIndex Integer32, dsPdistControlDataSource DataSource, dsPdistControlMaxDesiredEntries Integer32, dsPdistControlCollectMode INTEGER, dsPdistControlDroppedFrames Counter32, dsPdistControlInserts Counter32, dsPdistControlDeletes Counter32, dsPdistControlCreateTime LastCreateTime, dsPdistControlOwner OwnerString, dsPdistControlStatus RowStatus } dsPdistControlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary and unique index for this dsPdistControlEntry." ::= { dsPdistControlEntry 1 } dsPdistControlDataSource OBJECT-TYPE SYNTAX DataSource MAX-ACCESS read-create STATUS current DESCRIPTION "The source of data for the this per-protocol DSCP distribution. The statistics in this group reflect all IPv4 and IPv6 packets on the local network segment attached to the identified interface. This object may not be modified if the associated dsPdistControlStatus object is equal to active(1)." ::= { dsPdistControlEntry 2 } dsPdistControlMaxDesiredEntries OBJECT-TYPE SYNTAX Integer32 (-1 | 1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of entries that are desired in the dsPdistStatsTable on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this value is set to -1, the probe may create any number of entries in this table. This object may not be modified if the associated dsPdistControlStatus object is equal to active(1)." ::= { dsPdistControlEntry 3 } dsPdistControlCollectMode OBJECT-TYPE SYNTAX INTEGER { netLayer(1), -- count L3 protocols appLayer(2), -- count application protocols netAndAppLayers(3) -- count L3 and app protocols } MAX-ACCESS read-create STATUS current DESCRIPTION "The packet layer(s) at which the agent should process DSCP information, for each monitored packet. If this object has a value of 'netLayer(1)', then the agent will include only network layer protocols in the associated dsPdistStatsTable. If this object has a value of 'appLayer(2)', then the agent will include only application layer protocols in the associated dsPdistStatsTable. Any 'terminal' protocol is considered to be an application protocol. If this object has a value of 'netAndAppLayers(3)', then the agent will include only network and application layer protocols in the associated dsPdistStatsTable. Note that entries for transport layer protocols (e.g., TCP) will not be created by the agent, even if detected by the agent. This object may not be modified if the associated dsPdistControlStatus object is equal to active(1)." ::= { dsPdistControlEntry 4 } dsPdistControlDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped." ::= { dsPdistControlEntry 5 } dsPdistControlInserts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a dsPdist entry has been inserted into the dsPdistTable. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting dsPdistControlDeletes from dsPdistControlInserts." ::= { dsPdistControlEntry 6 } dsPdistControlDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a dsPdist entry has been deleted from the dsPdist table (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting dsPdistControlDeletes from dsPdistControlInserts." ::= { dsPdistControlEntry 7 } dsPdistControlCreateTime OBJECT-TYPE SYNTAX LastCreateTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls." ::= { dsPdistControlEntry 8 } dsPdistControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { dsPdistControlEntry 9 } dsPdistControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the dsPdistStatsTable shall be deleted." ::= { dsPdistControlEntry 10 } -- -- Per-Protocol Statistics Table -- dsPdistStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF DsPdistStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information on Per Protocol DSCP usage." ::= { dsPdistObjects 2 } dsPdistStatsEntry OBJECT-TYPE SYNTAX DsPdistStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information on Differentiated Services DSCP usage, containing packet and octet counters for each DSCP configured for collection, and each protocol (as identified by the protocolDirLocalIndex for the protocol) identified in each monitored packet. The dsPdistControlIndex value in the index identifies the dsPdistControlEntry on whose behalf this entry was created. Only entries with non-zero statistics will be returned by the agent, in order to reduce the amount of polling required to retrieve data from this table. That is, an entry will be created when a packet of that type and DSCP value is detected by the agent. Note that only protocols which are encapsulated in IPv4 or IPv6 packets will be counted in this table, as indicated by the protocolDirTable configuration. An example of the indexing of this entry is dsPdistStatsPkts.9.29943.42.16." INDEX { dsPdistControlIndex, dsPdistTimeMark, protocolDirLocalIndex, dsPdistDsCodept } ::= { dsPdistStatsTable 1 } DsPdistStatsEntry ::= SEQUENCE { dsPdistTimeMark TimeFilter, dsPdistDsCodept DSCodePoint, dsPdistStatsPkts ZeroBasedCounter32, dsPdistStatsOctets ZeroBasedCounter32, dsPdistStatsOvflPkts ZeroBasedCounter32, dsPdistStatsOvflOctets ZeroBasedCounter32, dsPdistStatsHCPkts ZeroBasedCounter64, dsPdistStatsHCOctets ZeroBasedCounter64, dsPdistStatsCreateTime LastCreateTime } dsPdistTimeMark OBJECT-TYPE SYNTAX TimeFilter MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Time Filter index for this table. This object may be used by a management station to retrieve only rows which have been created or modified since a particular time. Note that the current value for a row are always returned and the TimeFilter is not a historical data archiving mechanism. Refer to RFC 2021 [RFC2021] for a detailed description of TimeFilter operation." ::= { dsPdistStatsEntry 1 } dsPdistDsCodept OBJECT-TYPE SYNTAX DSCodePoint MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSCP value associated with the aggregated statistics for a particular protocol." ::= { dsPdistStatsEntry 2 } dsPdistStatsPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, monitored by this agent, and identified to be using a particular DSCP value in the DS header, on behalf of the protocol identified by the associated protocolDirLocalIndex value." ::= { dsPdistStatsEntry 3 } dsPdistStatsOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets in packets, monitored by this agent and identified to be using a particular DSCP value in the DS header, on behalf of the protocol identified by the associated protocolDirLocalIndex value. Note that this object doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol." ::= { dsPdistStatsEntry 4 } dsPdistStatsOvflPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsPdistStatsPkts counter has overflowed. Note that this object will only be instantiated if the associated dsPdistStatsHCPkts object is also instantiated for a particular dataSource." ::= { dsPdistStatsEntry 5 } dsPdistStatsOvflOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsPdistStatsOctets counter has overflowed. Note that this object will only be instantiated if the associated dsPdistStatsHCOctets object is also instantiated for a particular dataSource." ::= { dsPdistStatsEntry 6 } dsPdistStatsHCPkts OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsPdistStatsPkts object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsPdistStatsEntry 7 } dsPdistStatsHCOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsPdistStatsOctets object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsPdistStatsEntry 8 } dsPdistStatsCreateTime OBJECT-TYPE SYNTAX LastCreateTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this dsPdistStats entry was last instantiated by the agent. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls." ::= { dsPdistStatsEntry 9 } -- -- Per-Protocol Statistics TopN Control Table -- dsPdistTopNControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DsPdistTopNControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of parameters that control the creation of a report of the top N dsPdist entries according to a selected metric." ::= { dsPdistObjects 3 } dsPdistTopNControlEntry OBJECT-TYPE SYNTAX DsPdistTopNControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsPdistTopNControlTable. Entries are created and deleted from this table by management action only, using the dsPdistTopNControlStatus RowStatus object. Activation of a control row in this table will cause an associated dsPdistTopNTable to be created and maintained by the agent." INDEX { dsPdistTopNControlIndex } ::= { dsPdistTopNControlTable 1 } DsPdistTopNControlEntry ::= SEQUENCE { dsPdistTopNControlIndex Integer32, dsPdistTopNControlPdistIndex Integer32, dsPdistTopNControlRateBase INTEGER, dsPdistTopNControlTimeRemaining Integer32, dsPdistTopNControlGeneratedReports Counter32, dsPdistTopNControlDuration Integer32, dsPdistTopNControlRequestedSize Integer32, dsPdistTopNControlGrantedSize Integer32, dsPdistTopNControlStartTime TimeStamp, dsPdistTopNControlOwner OwnerString, dsPdistTopNControlStatus RowStatus } dsPdistTopNControlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the dsPdistTopNControlTable. Each such entry defines one Top N report prepared for one RMON dataSource." ::= { dsPdistTopNControlEntry 1 } dsPdistTopNControlPdistIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The dsPdistTable for which a top N report will be prepared on behalf of this entry. The dsPdistTable is identified by the value of the dsPdistControlIndex for that table - that value is used here to identify the particular table. This object may not be modified if the associated dsPdistTopNControlStatus object is equal to active(1)." ::= { dsPdistTopNControlEntry 2 } dsPdistTopNControlRateBase OBJECT-TYPE SYNTAX INTEGER { dsPdistTopNPkts(1), dsPdistTopNOctets(2), dsPdistTopNHCPkts(3), dsPdistTopNHCOctets(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable for each dsPdist that the dsPdistTopNRate and dsPdistTopNHCRate variables are based upon. Each dsPdistTopN report generated on behalf of this control entry will be ranked in descending order, based on the associated dsPdistStatsTable counter, identified by this object. The following table identifies the dsPdistTable counter associated with each enumeration: Enumeration RateBase MIB Object ----------- ------------------- dsPdistTopNPkts dsPdistStatsPkts dsPdistTopNOctets dsPdistStatsOctets dsPdistTopNHCPkts dsPdistStatsHCPkts dsPdistTopNHCOctets dsPdistStatsHCOctets Note that the dsPdistTopNHCPkts and dsPdistTopNHCOctets enumerations are only available if the agent supports High Capacity RMON collection. This object may not be modified if the associated dsPdistTopNControlStatus object is equal to active(1)." ::= { dsPdistTopNControlEntry 3 } dsPdistTopNControlTimeRemaining OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left in the report currently being collected. When this object is modified by the management station, a new collection is started, possibly aborting a currently running report. The new value is used as the requested duration of this report, and is immediately loaded into the associated dsPdistTopNControlDuration object. When the report finishes, the probe will automatically start another collection with the same initial value of dsPdistTopNControlTimeRemaining. Thus the management station may simply read the resulting reports repeatedly, checking the startTime and duration each time to ensure that a report was not missed or that the report parameters were not changed. While the value of this object is non-zero, it decrements by one per second until it reaches zero. At the time that this object decrements to zero, the report is made accessible in the dsPdistTopNTable, overwriting any report that may be there. When this object is modified by the management station, any associated entries in the dsPdistTopNTable shall be deleted." DEFVAL { 1800 } ::= { dsPdistTopNControlEntry 4 } dsPdistTopNControlGeneratedReports OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of reports that have been generated by this entry." ::= { dsPdistTopNControlEntry 5 } dsPdistTopNControlDuration OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that this report has collected during the last sampling interval. When the associated dsPdistTopNControlTimeRemaining object is set, this object shall be set by the probe to the same value and shall not be modified until the next time the dsPdistTopNControlTimeRemaining is set. This value shall be zero if no reports have been requested for this dsPdistTopNControlEntry." ::= { dsPdistTopNControlEntry 6 } dsPdistTopNControlRequestedSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of dsPdist entries requested for this report. When this object is created or modified, the probe should set dsPdistTopNControlGrantedSize as closely to this object as is possible for the particular probe implementation and available resources." DEFVAL { 150 } ::= { dsPdistTopNControlEntry 7 } dsPdistTopNControlGrantedSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of dsPdist entries in this report. When the associated dsPdistTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated dsPdistTopNControlRequestedSize object. When the associated dsPdistTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated dsPdistTopNControlRequestedSize object. Protocol entries with the highest value of dsPdistTopNRate or dsPdistTopNHCRate (depending on the value of the associated dsPdistTopNControlRateBase object) shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more dsPdist entries." ::= { dsPdistTopNControlEntry 8 } dsPdistTopNControlStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this top N report was last started. In other words, this is the time that the associated dsPdistTopNControlTimeRemaining object was modified to start the requested report or the time the report was last automatically (re)started. This object may be used by the management station to determine if a report was missed or not." ::= { dsPdistTopNControlEntry 9 } dsPdistTopNControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { dsPdistTopNControlEntry 10 } dsPdistTopNControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this dsPdistTopNControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the dsPdistTopNTable shall be deleted by the agent." ::= { dsPdistTopNControlEntry 11 } -- -- dsPdist TopN Table -- dsPdistTopNTable OBJECT-TYPE SYNTAX SEQUENCE OF DsPdistTopNEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of statistics for those protocol distribution entries that have counted the highest number of octets or packets. Note that dsPdist entries which did not increment at all during the report interval are not included in dsPdistTopN reports." ::= { dsPdistObjects 4 } dsPdistTopNEntry OBJECT-TYPE SYNTAX DsPdistTopNEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsPdistTopNTable. The dsPdistTopNControlIndex value in the index identifies the dsPdistTopNControlEntry on whose behalf this entry was created." INDEX { dsPdistTopNControlIndex, dsPdistTopNIndex } ::= { dsPdistTopNTable 1 } DsPdistTopNEntry ::= SEQUENCE { dsPdistTopNIndex Integer32, dsPdistTopNProtocolDirLocalIndex Integer32, dsPdistTopNDsCodept DSCodePoint, dsPdistTopNRate Gauge32, dsPdistTopNRateOvfl Gauge32, dsPdistTopNHCRate Counter64 -- Gauge64 } dsPdistTopNIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the dsPdistTopNTable among those in the same report. This index is between 1 and N, where N is the number of entries in this report." ::= { dsPdistTopNEntry 1 } dsPdistTopNProtocolDirLocalIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The protocolDirLocalIndex value which identifies the protocol associated with this entry." ::= { dsPdistTopNEntry 2 } dsPdistTopNDsCodept OBJECT-TYPE SYNTAX DSCodePoint MAX-ACCESS read-only STATUS current DESCRIPTION "The DSCP value associated with protocol identified in this entry." ::= { dsPdistTopNEntry 3 } dsPdistTopNRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of change in the selected variable during this sampling interval. The selected variable is this protocol's instance of the object selected by dsPdistTopNControlRateBase. If the associated dsPdistTopNControlRateBase is equal to 'dsPdistTopNHCPkts' or 'dsPdistTopNHCOctets', then this object will contain the the least significant 32 bits of the associated dsPdistTopNHCRate object." ::= { dsPdistTopNEntry 4 } dsPdistTopNRateOvfl OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The most significant 32 bits of the associated dsPdistTopNHCRate object. If the associated dsPdistTopNControlRateBase is equal to 'dsPdistTopNHCPkts' or 'dsPdistTopNHCOctets', then this object will contain the upper 32 bits of the associated dsPdistTopNHCRate object. If the associated dsPdistTopNControlRateBase is equal to 'dsPdistTopNPkts' or 'dsPdistTopNOctets', then this object will contain the value zero. The agent may choose not to instantiate this object if High Capacity RMON collection is not supported." ::= { dsPdistTopNEntry 5 } dsPdistTopNHCRate OBJECT-TYPE SYNTAX Counter64 -- Gauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of change in the selected variable during this sampling interval. The selected variable is this protocol's instance of the object selected by dsPdistTopNControlRateBase. If the associated dsPdistTopNControlRateBase is equal to 'dsPdistTopNPkts' or 'dsPdistTopNOctets', then this object will contain the value zero, and the associated dsPdistTopNRate object will contain the change in the selected variable during the sampling interval. The agent may choose not to instantiate this object if High Capacity RMON collection is not supported." ::= { dsPdistTopNEntry 6 } -- *********************************************************** -- * * -- * P E R - H O S T C O L L E C T I O N S * -- * * -- *********************************************************** -- -- IP Host Statistics Control Table -- dsHostControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DsHostControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Controls setup of per DSCP, per IP host distribution statistics." ::= { dsHostObjects 1 } dsHostControlEntry OBJECT-TYPE SYNTAX DsHostControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsHostControlTable. Entries are created and deleted from this table by management action only, using the dsHostControlStatus RowStatus object. Activation of a control row in this table will cause an associated dsHostTable to be created and maintained by the agent." INDEX { dsHostControlIndex } ::= { dsHostControlTable 1 } DsHostControlEntry ::= SEQUENCE { dsHostControlIndex Integer32, dsHostControlDataSource DataSource, dsHostControlMaxDesiredEntries Integer32, dsHostControlNumAddrBits Integer32, dsHostControlDroppedFrames Counter32, dsHostControlInserts Counter32, dsHostControlDeletes Counter32, dsHostControlCreateTime LastCreateTime, dsHostControlOwner OwnerString, dsHostControlStatus RowStatus } dsHostControlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary and unique index for this dsHostControlEntry." ::= { dsHostControlEntry 1 } dsHostControlDataSource OBJECT-TYPE SYNTAX DataSource MAX-ACCESS read-create STATUS current DESCRIPTION "The source of data for the associated dsHostTable. The statistics in this group reflect all IPv4 and IPv6 packets on the local network segment attached to the identified interface. This object may not be modified if the associated dsHostControlStatus object is equal to active(1)." ::= { dsHostControlEntry 2 } dsHostControlMaxDesiredEntries OBJECT-TYPE SYNTAX Integer32 (-1 | 1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of entries that are desired in the dsHostTable on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this value is set to -1, the probe may create any number of entries in this table. This object may not be modified if the associated dsHostControlStatus object is equal to active(1)." ::= { dsHostControlEntry 3 } dsHostControlNumAddrBits OBJECT-TYPE SYNTAX Integer32 (8..32) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of 'leftmost' contiguous bits in the IPv4 host address (as identified by the dsHostAddress object) that should be maintained in this collection. If this object has a value less than '32', then 'm' rightmost bits, where 'm' is equal to '32 - dsHostControlNumAddrBits', will be cleared to zero for counting purposes only. The 'leftmost' bit is the most significant bit of the first network-byte-order octet of the address. Note that this object only affects IPv4 host entries in the associated dsHostTable. IPv6 entries are not affected by this object. This object may not be modified if the associated dsHostControlStatus object is equal to active(1)." DEFVAL { 32 } ::= { dsHostControlEntry 4 } dsHostControlDroppedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for the associated dsHost entries for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that if the dsHostTable is inactive because no appropriate protocols are enabled in the protocol directory, this value should be 0. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped." ::= { dsHostControlEntry 5 } dsHostControlInserts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a dsHost entry has been inserted into the dsHost table. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting dsHostControlDeletes from dsHostControlInserts." ::= { dsHostControlEntry 6 } dsHostControlDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a dsHost entry has been deleted from the dsHost table (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting dsHostControlDeletes from dsHostControlInserts." ::= { dsHostControlEntry 7 } dsHostControlCreateTime OBJECT-TYPE SYNTAX LastCreateTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls." ::= { dsHostControlEntry 8 } dsHostControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { dsHostControlEntry 9 } dsHostControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this dsHostControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the dsHostTable shall be deleted." ::= { dsHostControlEntry 10 } -- -- IP Host Statistics Table -- dsHostTable OBJECT-TYPE SYNTAX SEQUENCE OF DsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A collection of statistics for a particular IPv4 or IPv6 address that has been discovered on a particular dataSource. The probe will add to this table all IP addresses seen as the source or destination address in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors." ::= { dsHostObjects 2 } dsHostEntry OBJECT-TYPE SYNTAX DsHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information on Differentiated Services DSCP usage, containing packet and octet counters for each DSCP configured for collection per host address, as identified in each monitored packet. The dsHostControlIndex value in the index identifies the dsHostControlEntry on whose behalf this entry was created. The length of the dsHostAddress field identifies the network layer protocol as either IPv4 or IPv6. Only entries with non-zero statistics will be returned by the agent, in order to reduce the amount of polling required to retrieve data from this table. An entry will be created when a packet of that type, IP address, and DSCP value is detected by the agent. An example of the indexing of this entry is dsHostOutPkts.1.24873.32.4.171.69.120.0" INDEX { dsHostControlIndex, dsHostTimeMark, dsHostDsCodept, dsHostAddress } ::= { dsHostTable 1 } DsHostEntry ::= SEQUENCE { dsHostTimeMark TimeFilter, dsHostDsCodept DSCodePoint, dsHostAddress OCTET STRING, dsHostInPkts ZeroBasedCounter32, dsHostInOctets ZeroBasedCounter32, dsHostInOvflPkts ZeroBasedCounter32, dsHostInOvflOctets ZeroBasedCounter32, dsHostInHCPkts ZeroBasedCounter64, dsHostInHCOctets ZeroBasedCounter64, dsHostOutPkts ZeroBasedCounter32, dsHostOutOctets ZeroBasedCounter32, dsHostOutOvflPkts ZeroBasedCounter32, dsHostOutOvflOctets ZeroBasedCounter32, dsHostOutHCPkts ZeroBasedCounter64, dsHostOutHCOctets ZeroBasedCounter64, dsHostCreateTime LastCreateTime } dsHostTimeMark OBJECT-TYPE SYNTAX TimeFilter MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Time Filter index for this table. This object may be used by a management station to retrieve only rows which have been created or modified since a particular time. Note that the current value for a row are always returned and the TimeFilter is not a historical data archiving mechanism. Refer to RFC 2021 [RFC2021] for a detailed description of TimeFilter operation." ::= { dsHostEntry 1 } dsHostDsCodept OBJECT-TYPE SYNTAX DSCodePoint MAX-ACCESS not-accessible STATUS current DESCRIPTION "The DSCP value associated with the aggregated statistics for a particular IP host." ::= { dsHostEntry 2 } dsHostAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4 | 16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address for this dsHostEntry. The length of the address string is used to determine if this entry represents an IPv4 or IPv6 address. For example, if the length of this object is '4', then this object is encoded as an IPv4 address in network byte order. Note that IPv4 addresses may have some 'rightmost' bits cleared to zero for counting purposes, as specified by the associated dsHostControlNumHostBits object." ::= { dsHostEntry 3 } dsHostInPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets without errors, using the identified DSCP and transmitted to this address, since it was added to the dsHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times." ::= { dsHostEntry 4 } dsHostInOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets, transmitted to this address and using the identified DSCP, since it was added to the dsHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol." ::= { dsHostEntry 5 } dsHostInOvflPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsHostInPkts counter has overflowed. Note that this object will only be instantiated if the associated dsHostInHCPkts object is also instantiated for a particular dataSource." ::= { dsHostEntry 6 } dsHostInOvflOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsHostInOctets counter has overflowed. Note that this object will only be instantiated if the associated dsHostInHCOctets object is also instantiated for a particular dataSource." ::= { dsHostEntry 7 } dsHostInHCPkts OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsHostInPkts object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsHostEntry 8 } dsHostInHCOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsHostInOctets object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsHostEntry 9 } dsHostOutPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets without errors, using the identified DSCP and transmitted by this address, since it was added to the dsHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times." ::= { dsHostEntry 10 } dsHostOutOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets, transmitted by this address and using the identified DSCP, since it was added to the dsHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol." ::= { dsHostEntry 11 } dsHostOutOvflPkts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsHostOutPkts counter has overflowed. Note that this object will only be instantiated if the associated dsHostOutHCPkts object is also instantiated for a particular dataSource." ::= { dsHostEntry 12 } dsHostOutOvflOctets OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dsHostOutOctets counter has overflowed. Note that this object will only be instantiated if the associated dsHostOutHCOctets object is also instantiated for a particular dataSource." ::= { dsHostEntry 13 } dsHostOutHCPkts OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsHostOutPkts object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsHostEntry 14 } dsHostOutHCOctets OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The 64-bit version of the dsHostOutOctets object. Note that this object will only be instantiated if the RMON agent supports High Capacity RMON for a particular dataSource." ::= { dsHostEntry 15 } dsHostCreateTime OBJECT-TYPE SYNTAX LastCreateTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this dsHost entry was last instantiated by the agent. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls." ::= { dsHostEntry 16 } -- -- DSCP Per-Protocol Per-Host Statistics TopN Control Table -- dsHostTopNControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DsHostTopNControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of parameters that control the creation of a report of the top N dsHost entries according to a selected metric." ::= { dsHostObjects 3 } dsHostTopNControlEntry OBJECT-TYPE SYNTAX DsHostTopNControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsHostTopNControlTable. Entries are created and deleted from this table by management action only, using the dsHostTopNControlStatus RowStatus object. Activation of a control row in this table will cause an associated dsHostTopNTable to be created and maintained by the agent." INDEX { dsHostTopNControlIndex } ::= { dsHostTopNControlTable 1 } DsHostTopNControlEntry ::= SEQUENCE { dsHostTopNControlIndex Integer32, dsHostTopNControlHostIndex Integer32, dsHostTopNControlRateBase INTEGER, dsHostTopNControlTimeRemaining Integer32, dsHostTopNControlGeneratedReports Counter32, dsHostTopNControlDuration Integer32, dsHostTopNControlRequestedSize Integer32, dsHostTopNControlGrantedSize Integer32, dsHostTopNControlStartTime TimeStamp, dsHostTopNControlOwner OwnerString, dsHostTopNControlStatus RowStatus } dsHostTopNControlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the dsHostTopNControlTable. Each such entry defines one Top N report prepared for one RMON dataSource." ::= { dsHostTopNControlEntry 1 } dsHostTopNControlHostIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The dsHostTable for which a top N report will be prepared on behalf of this entry. The dsHostTable is identified by the value of the dsHostControlIndex for that table - that value is used here to identify the particular table. This object may not be modified if the associated dsHostTopNControlStatus object is equal to active(1)." ::= { dsHostTopNControlEntry 2 } dsHostTopNControlRateBase OBJECT-TYPE SYNTAX INTEGER { dsHostTopNInPkts(1), dsHostTopNInOctets(2), dsHostTopNOutPkts(3), dsHostTopNOutOctets(4), dsHostTopNTotalPkts(5), dsHostTopNTotalOctets(6), dsHostTopNInHCPkts(7), dsHostTopNInHCOctets(8), dsHostTopNOutHCPkts(9), dsHostTopNOutHCOctets(10), dsHostTopNTotalHCPkts(11), dsHostTopNTotalHCOctets(12) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable(s) for each dsHost that the dsHostTopNRate and dsHostTopNHCRate variables are based upon. Each dsHostTopN report generated on behalf of this control entry will be ranked in descending order, based on the associated dsHostTable counter(s), identified by this object. The following table identifies the dsHostTable counters associated with each enumeration: Enumeration RateBase MIB Objects ----------- -------------------- dsHostTopNInPkts dsHostInPkts dsHostTopNInOctets dsHostInOctets dsHostTopNOutPkts dsHostOutPkts dsHostTopNOutOctets dsHostOutOctets dsHostTopNTotalPkts dsHostInPkts + dsHostOutPkts dsHostTopNTotalOctets dsHostInOctets + dsHostOutOctets dsHostTopNInHCPkts dsHostInHCPkts dsHostTopNInHCOctets dsHostInHCOctets dsHostTopNOutHCPkts dsHostOutHCPkts dsHostTopNOutHCOctets dsHostOutHCPkts dsHostTopNTotalHCPkts dsHostInHCPkts + dsHostOutHCPkts dsHostTopNTotalHCOctets dsHostInHCOctets + dsHostOutHCOctets The following enumerations are only available if the agent supports High Capacity RMON collection: dsHostTopNInHCPkts dsHostTopNInHCOctets dsHostTopNOutHCPkts dsHostTopNOutHCOctets dsHostTopNTotalHCPkts dsHostTopNTotalHCOctets It is an implementation-specific matter whether an agent can detect an overflow condition resulting from the addition of two counter delta values for the following enumerations: dsHostTopNTotalPkts dsHostTopNTotalOctets dsHostTopNTotalHCPkts dsHostTopNTotalHCOctets In the event such an overflow condition can be detected by the agent, the associated dsHostTopNRate, dsHostTopNRateOvfl, and/or dsHostTopNHCRate objects should be set to their maximum value. This object may not be modified if the associated dsHostTopNControlStatus object is equal to active(1)." ::= { dsHostTopNControlEntry 3 } dsHostTopNControlTimeRemaining OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds left in the report currently being collected. When this object is modified by the management station, a new collection is started, possibly aborting a currently running report. The new value is used as the requested duration of this report, and is immediately loaded into the associated dsHostTopNControlDuration object. When the report finishes, the probe will automatically start another collection with the same initial value of dsHostTopNControlTimeRemaining. Thus the management station may simply read the resulting reports repeatedly, checking the startTime and duration each time to ensure that a report was not missed or that the report parameters were not changed. While the value of this object is non-zero, it decrements by one per second until it reaches zero. At the time that this object decrements to zero, the report is made accessible in the dsHostTopNTable, overwriting any report that may be there. When this object is modified by the management station, any associated entries in the dsHostTopNTable shall be deleted." DEFVAL { 1800 } ::= { dsHostTopNControlEntry 4 } dsHostTopNControlGeneratedReports OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of reports that have been generated by this entry." ::= { dsHostTopNControlEntry 5 } dsHostTopNControlDuration OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that this report has collected during the last sampling interval. When the associated dsHostTopNControlTimeRemaining object is set, this object shall be set by the probe to the same value and shall not be modified until the next time the dsHostTopNControlTimeRemaining is set. This value shall be zero if no reports have been requested for this dsHostTopNControlEntry." ::= { dsHostTopNControlEntry 6 } dsHostTopNControlRequestedSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of dsHost entries requested for this report. When this object is created or modified, the probe should set dsHostTopNControlGrantedSize as closely to this object as is possible for the particular probe implementation and available resources." DEFVAL { 150 } ::= { dsHostTopNControlEntry 7 } dsHostTopNControlGrantedSize OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of dsHost entries in this report. When the associated dsHostTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated dsHostTopNControlRequestedSize object. When the associated dsHostTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated dsHostTopNControlRequestedSize object. Protocol entries with the highest value of dsHostTopNRate or dsHostTopNHCRate (depending on the value of the associated dsHostTopNControlRateBase object) shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more dsHost entries." ::= { dsHostTopNControlEntry 8 } dsHostTopNControlStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this top N report was last started. In other words, this is the time that the associated dsHostTopNControlTimeRemaining object was modified to start the requested report or the time the report was last automatically (re)started. This object may be used by the management station to determine if a report was missed or not." ::= { dsHostTopNControlEntry 9 } dsHostTopNControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The entity that configured this entry and is therefore using the resources assigned to it." ::= { dsHostTopNControlEntry 10 } dsHostTopNControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this dsHostTopNControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the dsHostTopNTable shall be deleted by the agent." ::= { dsHostTopNControlEntry 11 } -- -- dsHost TopN Table -- dsHostTopNTable OBJECT-TYPE SYNTAX SEQUENCE OF DsHostTopNEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of statistics for those dsHost entries that have counted the highest number of octets or packets. Note that dsHost entries which did not increment at all during the report interval are not included in dsHostTopN reports." ::= { dsHostObjects 4 } dsHostTopNEntry OBJECT-TYPE SYNTAX DsHostTopNEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the dsHostTopNTable. The dsHostTopNControlIndex value in the index identifies the dsHostTopNControlEntry on whose behalf this entry was created." INDEX { dsHostTopNControlIndex, dsHostTopNIndex } ::= { dsHostTopNTable 1 } DsHostTopNEntry ::= SEQUENCE { dsHostTopNIndex Integer32, dsHostTopNAddress OCTET STRING, dsHostTopNDsCodept DSCodePoint, dsHostTopNRate Gauge32, dsHostTopNRateOvfl Gauge32, dsHostTopNHCRate Counter64 -- Gauge64 } dsHostTopNIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that uniquely identifies an entry in the dsHostTopNTable among those in the same report. This index is between 1 and N, where N is the number of entries in this report." ::= { dsHostTopNEntry 1 } dsHostTopNAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4 | 16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network address of the IP host identified in this entry. The length of this field identifies the network layer protocol as either IPv4 or IPv6. Addresses are encoded in network byte order." ::= { dsHostTopNEntry 2 } dsHostTopNDsCodept OBJECT-TYPE SYNTAX DSCodePoint MAX-ACCESS read-only STATUS current DESCRIPTION "The DSCP value associated with host identified in this entry." ::= { dsHostTopNEntry 3 } dsHostTopNRate OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of change in the selected variable during this sampling interval. The selected variable is this host's instance of the object selected by dsHostTopNControlRateBase. If the associated dsHostTopNControlRateBase indicates a High Capacity RMON enumeration, (e.g. 'dsHostTopNInHCPkts'), then this object will contain the the least significant 32 bits of the associated dsHostTopNHCRate object." ::= { dsHostTopNEntry 4 } dsHostTopNRateOvfl OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The most significant 32 bits of the associated dsHostTopNHCRate object. If the associated dsHostTopNControlRateBase is equal to any of the High Capacity RMON enumerations (e.g. 'dsHostTopNInHCPkts'), then this object will contain the upper 32 bits of the associated dsHostTopNHCRate object. If the associated dsHostTopNControlRateBase is not equal to any of High Capacity RMON enumerations, then this object will contain the value zero. The agent may choose not to instantiate this object if High Capacity RMON collection is not supported." ::= { dsHostTopNEntry 5 } dsHostTopNHCRate OBJECT-TYPE SYNTAX Counter64 -- Gauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of change in the selected variable during this sampling interval. The selected variable is this host's instance of the object selected by dsHostTopNControlRateBase. If the associated dsHostTopNControlRateBase is not equal to any of the High Capacity RMON enumerations (e.g., 'dsHostTopNInPkts'), then this object will contain the value zero, and the associated dsHostTopNRate object will contain the change in the selected variable during the sampling interval. The agent may choose not to instantiate this object if High Capacity RMON collection is not supported." ::= { dsHostTopNEntry 6 } -- -- Notifications Section -- (none defined) -- -- -- Conformance Section -- dsMonCompliances OBJECT IDENTIFIER ::= { dsMonConformance 1 } dsMonGroups OBJECT IDENTIFIER ::= { dsMonConformance 2 } dsMonCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the Differentiated Services Monitoring MIB." MODULE -- this module MANDATORY-GROUPS { dsStatsGroup, dsHostGroup } GROUP dsStatsHCGroup DESCRIPTION "The dsStatsHCGroup is mandatory for systems which implement the dsStatsGroup and also implement High Capacity RMON monitoring." GROUP dsPdistGroup DESCRIPTION "The dsPdistGroup is mandatory for systems which implement DSCP monitoring and the protocolDirTable from the RMON-2 MIB [RFC2021]." GROUP dsPdistHCGroup DESCRIPTION "The dsPdistHCGroup is mandatory for systems which implement the dsPdistGroup and also implement High Capacity RMON monitoring." GROUP dsHostHCGroup DESCRIPTION "The dsHostHCGroup is mandatory for systems which implement the dsHostGroup and also implement High Capacity RMON monitoring." ::= { dsMonCompliances 1 } dsStatsGroup OBJECT-GROUP OBJECTS { dsStatsControlDataSource, dsStatsControlDroppedFrames, dsStatsControlCreateTime, dsStatsControlOwner, dsStatsControlStatus, dsStatsInPkts, dsStatsInOctets, dsStatsOutPkts, dsStatsOutOctets } STATUS current DESCRIPTION "A collection of objects providing per DSCP statistics." ::= { dsMonGroups 1 } dsStatsHCGroup OBJECT-GROUP OBJECTS { dsStatsInOvflPkts, dsStatsInOvflOctets, dsStatsInHCPkts, dsStatsInHCOctets, dsStatsOutOvflPkts, dsStatsOutOvflOctets, dsStatsOutHCPkts, dsStatsOutHCOctets } STATUS current DESCRIPTION "A collection of objects providing per DSCP statistics for high capacity data sources." ::= { dsMonGroups 2 } dsPdistGroup OBJECT-GROUP OBJECTS { dsPdistControlDataSource, dsPdistControlMaxDesiredEntries, dsPdistControlCollectMode, dsPdistControlDroppedFrames, dsPdistControlInserts, dsPdistControlDeletes, dsPdistControlCreateTime, dsPdistControlOwner, dsPdistControlStatus, dsPdistStatsPkts, dsPdistStatsOctets, dsPdistStatsCreateTime, dsPdistTopNControlPdistIndex, dsPdistTopNControlRateBase, dsPdistTopNControlTimeRemaining, dsPdistTopNControlGeneratedReports, dsPdistTopNControlDuration, dsPdistTopNControlRequestedSize, dsPdistTopNControlGrantedSize, dsPdistTopNControlStartTime, dsPdistTopNControlOwner, dsPdistTopNControlStatus, dsPdistTopNProtocolDirLocalIndex, dsPdistTopNDsCodept, dsPdistTopNRate } STATUS current DESCRIPTION "A collection of objects providing per protocol DSCP monitoring extensions to the RMON-2 MIB." ::= { dsMonGroups 3 } dsPdistHCGroup OBJECT-GROUP OBJECTS { dsPdistStatsOvflPkts, dsPdistStatsOvflOctets, dsPdistStatsHCPkts, dsPdistStatsHCOctets, dsPdistTopNRateOvfl, dsPdistTopNHCRate } STATUS current DESCRIPTION "A collection of objects providing per protocol DSCP monitoring extensions to the RMON-2 MIB for High Capacicy networks." ::= { dsMonGroups 4 } dsHostGroup OBJECT-GROUP OBJECTS { dsHostControlDataSource, dsHostControlMaxDesiredEntries, dsHostControlNumAddrBits, dsHostControlDroppedFrames, dsHostControlInserts, dsHostControlDeletes, dsHostControlCreateTime, dsHostControlOwner, dsHostControlStatus, dsHostInPkts, dsHostInOctets, dsHostOutPkts, dsHostOutOctets, dsHostCreateTime, dsHostTopNControlHostIndex, dsHostTopNControlRateBase, dsHostTopNControlTimeRemaining, dsHostTopNControlGeneratedReports, dsHostTopNControlDuration, dsHostTopNControlRequestedSize, dsHostTopNControlGrantedSize, dsHostTopNControlStartTime, dsHostTopNControlOwner, dsHostTopNControlStatus, dsHostTopNAddress, dsHostTopNDsCodept, dsHostTopNRate } STATUS current DESCRIPTION "A collection of objects providing per IP Host DSCP monitoring functions." ::= { dsMonGroups 5 } dsHostHCGroup OBJECT-GROUP OBJECTS { dsHostInOvflPkts, dsHostInOvflOctets, dsHostInHCPkts, dsHostInHCOctets, dsHostOutOvflPkts, dsHostOutOvflOctets, dsHostOutHCPkts, dsHostOutHCOctets, dsHostTopNRateOvfl, dsHostTopNHCRate } STATUS current DESCRIPTION "A collection of objects providing per IP Host DSCP monitoring functions for High Capacity networks." ::= { dsMonGroups 6 } END -- -- Copyright (C) The Internet Society (1999). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it or -- assist in its implementation may be prepared, copied, published and -- distributed, in whole or in part, without restriction of any kind, -- provided that the above copyright notice and this paragraph are included -- on all such copies and derivative works. However, this document itself -- may not be modified in any way, such as by removing the copyright notice -- or references to the Internet Society or other Internet organizations, -- except as needed for the purpose of developing Internet standards in -- which case the procedures for copyrights defined in the Internet -- Standards process must be followed, or as required to translate it into -- languages other than English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- -- This document and the information contained herein is provided on an "AS -- IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK -- FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT -- LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT -- INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR -- FITNESS FOR A PARTICULAR PURPOSE."