-- extracted from draft-ietf-hubmib-efm-cu-mib-04.txt -- at Fri Oct 28 06:38:09 2005 EFM-CU-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32, Counter32, mib-2 FROM SNMPv2-SMI -- RFC 2578 TEXTUAL-CONVENTION, TruthValue, RowStatus, PhysAddress FROM SNMPv2-TC -- RFC 2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC 3411 ifIndex, ifSpeed, InterfaceIndex FROM IF-MIB -- RFC 2863 ; efmCuMIB MODULE-IDENTITY LAST-UPDATED "200510240000Z" -- October 24, 2005 ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group" CONTACT-INFO "WG charter: http://www.ietf.org/html.charters/hubmib-charter.html Mailing Lists: General Discussion: hubmib@ietf.org To Subscribe: hubmib-request@ietf.org In Body: subscribe your_email_address Chair: Dan Romascanu Postal: Avaya Atidim Technology Park, Bldg. 3 Tel Aviv 61131 Israel Tel: +972 3 645 8414 E-mail: dromasca@avaya.com Editor: Edward Beili Postal: Actelis Networks Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 10173 Israel Tel: +972-3-924-3491 E-mail: edward.beili@actelis.com" DESCRIPTION "The objects in this MIB module are used to manage the Ethernet in the First Mile (EFM) Copper (EFMCu) Interfaces 2BASE-TL and 10PASS-TS, defined in IEEE Std. 802.3ah-2004. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Std 802.3ah-2004: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications - Amendment: Media Access Control Parameters, Physical Layers and Management Parameters for Subscriber Access Networks', 07 September 2004. Of particular interest are Clause 61, 'Physical Coding Sublayer (PCS) and common specifications, type 10PASS-TS and type 2BASE-TL', Clause 30, 'Management', Clause 45, 'Management Data Input/Output (MDIO) Interface', Annex 62A, 'PMD profiles for 10PASS-TS' and Annex 63A, 'PMD profiles for 2BASE-TL'. Naming Conventions: Atn - Attenuation CO - Central Office CPE - Customer Premises Equipment EFM - Ethernet in the First Mile EFMCu - EFM Copper MDIO - Management Data Input/Output Mgn - Margin PAF - PME Aggregation Function PCS - Physical Coding Sublayer PMD - Physical Medium Dependent PME - Physical Medium Entity PSD - Power Spectral Density SNR - Signal to Noise Ratio TCPAM - Trellis Coded Pulse Amplitude Modulation Copyright (C) The Internet Society (2004). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices." REVISION "200510240000Z" -- October 24, 2005 DESCRIPTION "Initial version, published as RFC XXXX." -- EdNote: Replace XXXX with the actual RFC number & -- remove this note ::= { mib-2 YYY } -- EdNote: Replace YYY with a real OID once it is -- allocated & remove this note. -- Sections of the module efmCuObjects OBJECT IDENTIFIER ::= { efmCuMIB 1 } efmCuConformance OBJECT IDENTIFIER ::= { efmCuMIB 2 } -- Groups in the module efmCuPort OBJECT IDENTIFIER ::= { efmCuObjects 1 } efmCuPme OBJECT IDENTIFIER ::= { efmCuObjects 2 } -- Textual Conventions ProfileIndex ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A unique value, greater than zero, for each PME configuration profile in the managed EFMCu port. It is recommended that values are assigned contiguously starting from 1. The value for each profile must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization." SYNTAX Unsigned32 (1..255) ProfileIndexOrZero ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "This textual convention is an extension of the ProfileIndex convention. The latter defines a greater than zero value used to identify a PME profile in the managed EFMCu port. This extension permits the additional value of zero. The value of zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero value migh include situations where current operational profile is unknown." SYNTAX Unsigned32 (0..255) ProfileIndexList ::= TEXTUAL-CONVENTION DISPLAY-HINT "1d:" STATUS current DESCRIPTION "Represents a list of up to 6 ProfileIndex's. The ProfileIndex textual convention defines a greater than zero value used to identify a PME profile in the managed EFMCu port. The value of this object is a concatenation of one or more (up to 6) octets, where each octet contains an 8-bit ProfileIndex value. The ProfileIndexList specifies a list of alternative profiles, any of which can be chosen for configuration of an PME." SYNTAX OCTET STRING (SIZE(1..6)) TruthValueOrUnknown ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention is an extension of the TruthValue convention. The latter defines a boolean value with possible values of true(1) and false(2). This extension permits the additional value of unknown(0), which can be returned as a result of GET operation, when an exact true or false value of the object cannot be determined." SYNTAX INTEGER { unknown(0), true(1), false(2) } -- Port Notifications Group efmCuPortNotifications OBJECT IDENTIFIER ::= { efmCuPort 0 } efmCuLowBandwidth NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific PCS ifSpeed, efmCuThreshLowBandwidth } STATUS current DESCRIPTION "This notification indicates that EFMCu port's data rate reached or dropped below a Low Bandwidth Threshold (i.e. bandwidth degradation happening in case of PAF when one or more PMEs drop)." -- EdNote: add throttling limitations here ::= { efmCuPortNotifications 1 } -- PCS Port group efmCuPortConfTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for Configuration of EFMCu 2BASE-TL/10PASS-TS (PCS) Ports. Entries in this table MUST be maintained in a persistent manner" ::= { efmCuPort 1 } efmCuPortConfEntry OBJECT-TYPE SYNTAX EfmCuPortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu Port Configuration table. Each entry represents an EFMCu port indexed by the ifIndex. Note that an EFMCu PCS port runs on top of a single or multiple PME port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { efmCuPortConfTable 1 } EfmCuPortConfEntry ::= SEQUENCE { efmCuPAFAdminState INTEGER, efmCuPAFDiscoveryCode PhysAddress, efmCuAdminProfile ProfileIndexList, efmCuTargetDataRate Unsigned32, efmCuTargetSnrMgn Unsigned32, efmCuThreshLowBandwidth Unsigned32, efmCuLowBandwidthEnable TruthValue } efmCuPAFAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative (desired) state of the PAF of the EFMCu port (PCS). When 'disabled', PME Aggregation will not be performed by the PCS. No more than a single PME can be assigned to this PCS in this case. When 'enabled', PAF will be performed by the PCS when the link is Up, even on a single attached PME, if PAF is supported. PCS ports incapable of supporting PAF SHALL return a value of 'disabled'. Attempts to 'enable' such ports SHALL be ignored. PAF 'enabled' port with multiple PMEs assigned cannot be 'disabled'. Attempts to 'disable' such port SHALL be rejected, until at most one PME is left assigned. Changing PAFAdminState is a traffic disruptive operation and as such SHALL be done when the link is Down. Attempts to change this object SHALL be ignored if the link is Up or Initializing. This object maps to the Clause 30 attribute aPAFAdminState. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the PAF enable bit in the 10P/2B PCS control register. This object MUST be maintained in a persistent manner." REFERENCE "[802.3ah] 61.2.2, 45.2.3.18.3" ::= { efmCuPortConfEntry 1 } efmCuPAFDiscoveryCode OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "PAF Discovery Code of the EFMCu port (PCS). A unique 6 Byte long code used by the Discovery function, when PAF is supported. PCS ports incapable of supporting PAF SHALL return a value of all zeroes. Attempts to change this object SHALL be ignored in this case. This object MUST be instantiated for the -O subtype PCS before writing operations on the efmCuPAFRemoteDiscoveryCode (Set_if_Clear and Clear_if_Same) are performed by PMEs associated with the PCS. The value of this object is read-only for -R port subtypes. The initial value of this object for -R ports after reset is 0. This value may be changed as a result of writing operation on efmCuPAFRemoteDiscoveryCode variable of remote PME of -O subtype, connected to one of the local PMEs associated with the PCS. Discovery MUST be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue if the link is Up or Initializing. The PAF Discovery code maps to the local Discovery code variable in PAF (note that it does not have a corresponding Clause 45 register)" REFERENCE "[802.3ah] 61.2.2.8.3, 61.2.2.8.4, 45.2.6.6.1" ::= { efmCuPortConfEntry 2 } efmCuAdminProfile OBJECT-TYPE SYNTAX ProfileIndexList MAX-ACCESS read-write STATUS current DESCRIPTION "Desired configuration Profile(s), common for all PMEs in the EFMCu port. This object is a list of pointers to entries in either efmCuPme2BProfileTable or efmCuPme10PProfileTable, depending on the current operating SubType of the EFMCu port as indicated by efmCuPortSide. The value of this object is a list of up to 6 indices of Profiles. If this list consists of a single Profile index, then all PMEs assigned to this EFMCu port SHALL be configured according to the Profile referenced by that index, unless it is overwritten by corresponding non-zero efmCuPmeAdminProfile, which takes precedence over efmCuAdminProfile. The list, consisting of more than one index, allows each PME in the port to be configured according to any Profile specified in the list. By default this object has a value of 0x01, referencing 1st entry in efmCuPme2BProfileTable or efmCuPme10PProfileTable. This object is writable and readable for the -O subtype (2BaseTL-O or 10PassTS-O) EFMCu ports. It is unavailable for the -R subtype (2BaseTL-R or 10PassTS-R) ports. Note that current operational Profile value is available via efmCuPmeOperProfile object. Modification of this object must be performed when the link is Down. Attempts to change this object MUST be rejected, if the link is Up or Initializing. Attempts to set this object to a list with a member value, that is not the value of the index for an active entry in the corresponding profile table, MUST be rejected. This object MUST be maintained in a persistent manner." REFERENCE "[802.3ah] 30.11.2.1.6" DEFVAL { '01'H } ::= { efmCuPortConfEntry 3 } efmCuTargetDataRate OBJECT-TYPE SYNTAX Unsigned32(1..100000|999999) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Desired EFMCu port 'net' (as seen across MII) Data Rate in Kbps, to be achieved during initialization, under spectral restrictions placed on each PME via efmCuAdminProfile or efmCuPmeAdminProfile, with the desired SNR Margin specified by efmCuTargetSnrMgn. In case of PAF, this object represents a sum of individual PME data rates, modified to compensate for fragmentation and 64/65B framing overhead (e.g. target data rate of 10Mbps shall allow lossless transmission of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap). The value is limited above by 100Mbps as this is the max burst rate across MII for EFMCu ports. The value between 1 and 100000 indicates that the total data rate (ifSpeed) of the EFMCu port after initialization should be equal to the target data rate or less, if the target data rate cannot be achieved under spectral restrictions specified by efmCuAdminProfile/efmCuPmeAdminProfile and with desired SNR margin. In case the copper environment allows to achieve higher total data rate than specified by the target, the excess capability SHALL be converted to additional SNR margin and spread evenly across all active PMEs assigned to the (PCS) port. The value of 999999 means that the target data rate is not fixed and should be set to the maximum attainable rate during initialization (Best Effort), under specified spectral restrictions and with desired SNR Margin. This object is read-write for the -O subtype EFMCu ports (2BaseTL-O/10PassTS-O) and not available for the -R subtypes. Changing of the Target Data Rate MUST be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. Note that current Data Rate of the EFMCu port is represented by ifSpeed object of IF-MIB. This object MUST be maintained in a persistent manner." ::= { efmCuPortConfEntry 4 } efmCuTargetSnrMgn OBJECT-TYPE SYNTAX Unsigned32(0..21) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Desired EFMCu port SNR Margin to be achieved on all PMEs assigned to the port, during initializiation. (The SNR margin is the difference between the desired SNR and the actual SNR). Note that 802.3ah recommends using default Target SNR Margin of 5dB for 2BASE-TL ports and 6dB for 10PASS-TS ports in order to achieve mean Bit Error Rate (BER) of 10^-7 at the PMA service interface. This object is read-write for the -O subtype EFMCu ports (2BaseTL-O/10PassTS-O) and not available for the -R subtypes. Changing of the Target SNR Margin MUST be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. Note that current SNR Margin of the PMEs comprising the EFMCu port is represented by efmCuPmeSnrMgn. This object MUST be maintained in a persistent manner." REFERENCE "[802.3ah] 61.1.2" ::= { efmCuPortConfEntry 5 } efmCuThreshLowBandwidth OBJECT-TYPE SYNTAX Unsigned32(400..100000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the EFMCu port Low Bandwidth alarm threshold. When the current value of ifSpeed for this port reaches or drops below this threshold, an efmCuLowBandwidth notification MAY be generated if enabled by efmCuLowBandwidthEnable. This object is read-write for the -O subtype EFMCu ports (2BaseTL-O/10PassTS-O) and not available for the -R subtypes. This object MUST be maintained in a persistent manner." ::= { efmCuPortConfEntry 6 } efmCuLowBandwidthEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuLowBandwidth notifications should be generated for this interface. Value of true(1) indicates that efmCuLowBandwidth notification is enabled. Value of false(2) indicates that the notification is disabled. This object MUST be maintained in a persistent manner." ::= { efmCuPortConfEntry 7 } efmCuPortCapabilityTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPortCapabilityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for Capabilities of EFMCu 2BASE-TL/10PASS-TS (PCS) Ports. Entries in this table MUST be maintained in a persistent manner" ::= { efmCuPort 2 } efmCuPortCapabilityEntry OBJECT-TYPE SYNTAX EfmCuPortCapabilityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu Port Capability table. Each entry represents an EFMCu port indexed by the ifIndex. Note that an EFMCu PCS port runs on top of a single or multiple PME port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { efmCuPortCapabilityTable 1 } EfmCuPortCapabilityEntry ::= SEQUENCE { efmCuPAFSupported TruthValue, efmCuPeerPAFSupported TruthValueOrUnknown, efmCuPAFCapacity Unsigned32, efmCuPeerPAFCapacity Unsigned32 } efmCuPAFSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "PME Aggregation Function (PAF) Capability of the EFMCu port (PCS). This object has a value of true(1) when the PCS can perform PME aggregation on the available PMEs. Ports incapable of PAF SHALL return a value of false(2). This object maps to the Clause 30 attribute aPAFSupported. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the PAF available bit in the 10P/2B capability register." REFERENCE "[802.3ah] 61.2.2, 30.11.1.1.4, 45.2.3.17.1" ::= { efmCuPortCapabilityEntry 1 } efmCuPeerPAFSupported OBJECT-TYPE SYNTAX TruthValueOrUnknown MAX-ACCESS read-only STATUS current DESCRIPTION "PME Aggregation Function (PAF) Capability of the EFMCu port (PCS) link partner. This object has a value of true(1) when the remote PCS can perform PME aggregation on its available PMEs. Ports whose peers are incapable of PAF, SHALL return a value of false(2). Ports whose peers cannot be reached because of the link state, SHALL return a value if unknown(0). This object maps to the Clause 30 attribute aRemotePAFSupported. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the Remote PAF supported bit in the 10P/2B capability register." REFERENCE "[802.3ah] 61.2.2, 30.11.1.1.9, 45.2.3.17.2" ::= { efmCuPortCapabilityEntry 2 } efmCuPAFCapacity OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PMEs that can be aggregated by the local PAF. The number of PMEs currently assigned to a particular EFMCu port (efmCuNumPMEs) is never greater than efmCuPAFCapacity. This object maps to the Clause 30 attribute aLocalPAFCapacity." REFERENCE "[802.3ah] 61.2.2, 30.11.1.1.6" ::= { efmCuPortCapabilityEntry 3 } efmCuPeerPAFCapacity OBJECT-TYPE SYNTAX Unsigned32 (0|1..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PMEs that can be aggregated by the PAF of the peer Phy (PCS port). Value of 0 is returned when peer PAF Capacity is unknown (peer cannot be reached). This object maps to the Clause 30 attribute aRemotePAFCapacity." REFERENCE "[802.3ah] 61.2.2, 30.11.1.1.10" ::= { efmCuPortCapabilityEntry 4 } efmCuPortStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides overall status information of EFMCu 2BASE-TL/10PASS-TS ports. This table contains live data from the equipment. As such, it is NOT persistent." ::= { efmCuPort 3 } efmCuPortStatusEntry OBJECT-TYPE SYNTAX EfmCuPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu Port Status table. Each entry represents an EFMCu port indexed by the ifIndex. Note that an EFMCu PCS port runs on top of a single or multiple PME port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { efmCuPortStatusTable 1 } EfmCuPortStatusEntry ::= SEQUENCE { efmCuFltStatus BITS, efmCuPortSide INTEGER, efmCuNumPMEs Unsigned32, efmCuPAFInErrors Counter32, efmCuPAFInSmallFragments Counter32, efmCuPAFInLargeFragments Counter32, efmCuPAFInBadFragments Counter32, efmCuPAFInLostFragments Counter32, efmCuPAFInLostStarts Counter32, efmCuPAFInLostEnds Counter32, efmCuPAFInOverflows Counter32 } efmCuFltStatus OBJECT-TYPE SYNTAX BITS { noPeer(0), pmeSubTypeMismatch(1), lowBandwidth(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "EFMCu (PCS) port Fault Status. This is a bitmap of possible conditions. The various bit positions are: noPeer - peer PHY cannot be reached (e.g. no PMEs attached, all PMEs are Down etc.) More info is available in efmCuPmeFltStatus. pmeSubTypeMismatch - local PMEs in the aggregation group are not of the same sub-type, e.g. some PMEs in the local device are -O while others are -R subtype. lowBandwidth - ifSpeed of the port reached or droped below efmCuThreshLowBandwidth This object is intended to supplement ifOperStatus object in IF-MIB. Additional information is available via efmCuPmeFltStatus object for each PME in the aggregation group (single PME if PAF is disabled)." REFERENCE "ifOperStatus in IF-MIB; efmCuPmeFltStatus" ::= { efmCuPortStatusEntry 1 } efmCuPortSide OBJECT-TYPE SYNTAX INTEGER { subscriber(1), office(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "EFM port mode of operation (subtype). The value of 'subscriber' indicates the port is designated as '-R' subtype (all PMEs assigned to this port are of subtype '-R'). The value of the 'office' indicates that the port is designated as '-O' subtype (all PMEs assigned to this port are of subtype '-O'). The value of 'unknown' indicates that the port has no assigned PMEs yet or that the assigned PMEs are not of the same side (subTypePMEMismatch). This object partially maps to the Clause 30 attribute aPhyEnd" REFERENCE "[802.3ah] 61.1, 30.11.1.1.2" ::= { efmCuPortStatusEntry 2 } efmCuNumPMEs OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of PMEs that is currently aggregated by the local PAF (assigned to the EFMCu port using ifStackTable). This number is never greater than efmCuPAFCapacity. This object SHALL be automatically incremented or decremented when a PME is added or deleted to/from the EFMCu port using ifStackTable." REFERENCE "[802.3ah] 61.2.2, 30.11.1.1.6" ::= { efmCuPortStatusEntry 3 } efmCuPAFInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of fragments that have been received across the gamma interface with RxErr asserted and discarded. This read-only counter is inactive (not incremented) when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF RX error register." REFERENCE "[802.3ah] 45.2.3.21" ::= { efmCuPortStatusEntry 4 } efmCuPAFInSmallFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of fragments smaller than minFragmentSize (64 Bytes), that have been received across the gamma interface and discarded. This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF small fragments register." REFERENCE "[802.3ah] 45.2.3.22" ::= { efmCuPortStatusEntry 5 } efmCuPAFInLargeFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of fragments larger than maxFragmentSize (512 Bytes), that have been received across the gamma interface and discarded. This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF large fragments register." REFERENCE "[802.3ah] 45.2.3.23" ::= { efmCuPortStatusEntry 6 } efmCuPAFInBadFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of fragments which do not fit into the sequence expected by the frame assembly function, that have been received across the gamma interface and discarded (the frame buffer is flushed to the next valid frame start). This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF bad fragments register." REFERENCE "[802.3ah] 45.2.3.25" ::= { efmCuPortStatusEntry 7 } efmCuPAFInLostFragments OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of gaps in the sequence of fragments, that have been received across the gamma interface (the frame buffer is flushed to the next valid frame start, when fragment/fragments expected by the frame assembly function is/are not received). This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF lost fragment register." REFERENCE "[802.3ah] 45.2.3.26" ::= { efmCuPortStatusEntry 8 } efmCuPAFInLostStarts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of missing StartOfPacket indicators expected by the frame assembly function. This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF lost start of fragment register." REFERENCE "[802.3ah] 45.2.3.27" ::= { efmCuPortStatusEntry 9 } efmCuPAFInLostEnds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of missing EndOfPacket indicators expected by the frame assembly function. This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF lost start of fragment register." REFERENCE "[802.3ah] 45.2.3.28" ::= { efmCuPortStatusEntry 10 } efmCuPAFInOverflows OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of fragements, received accross the gamma interface and discarded, which would have caused the frame assembly buffer to overflow. This read-only counter is inactive when the PAF is unsupported or disabled. Upon disabling the PAF, the counter retains its previous value. If a Clause 45 MDIO Interface to the PCS is present, then this object maps to the 10P/2B PAF overflow register." REFERENCE "[802.3ah] 45.2.3.24" ::= { efmCuPortStatusEntry 11 } -- PME Notifications Group efmCuPmeNotifications OBJECT IDENTIFIER ::= { efmCuPme 0 } -- EdNote: Should I add more notifications here, for example -- efmCuPmePerfES, -- efmCuPmePerfSES, -- efmCuPmePerfCRCanomalies, -- efmCuPmePerfLOSWS, -- efmCuPmePerfUAS, -- efmCuPmeDeviceFault, -- efmCuPmeLocalPowerLoss -- Another option would be to reference HDSL2-SHDSL-LINE-MIB -- or VDSL-LINE-EXT-MCM-MIB, reusing notifications defined there. efmCuPmeLineAtnCrossing NOTIFICATION-TYPE OBJECTS { efmCuPmeLineAtn, efmCuPmeThreshLineAtn } STATUS current DESCRIPTION "This notification indicates that the loop attenuation threshold (as per the efmCuPmeThreshLineAtn value) has been reached/exceeded for the 2BASE-TL/10PASS-TS PME. This notification MAY be send on the crossing event in both directions: from normal to exceeded and from exceeded to normal. Generation of this notification is controlled by the efmCuPmeLineAtnCrossingEnable object." -- EdNote: add throttling limitations here, with 10 sec -- debouncing on clear to prevenmt intermittent alarms ::= { efmCuPmeNotifications 1 } efmCuPmeSnrMgnCrossing NOTIFICATION-TYPE OBJECTS { efmCuPmeSnrMgn, efmCuPmeThreshSnrMgn } STATUS current DESCRIPTION "This notification indicates that the SNR margin threshold (as per the efmCuPmeThreshSnrMgn value) has been reached/exceeded for the 2BASE-TL/10PASS-TS PME. This notification MAY be send on the crossing event in both directions: from normal to exceeded and from exceeded to normal. Generation of this notification is controlled by the efmCuPmeSnrMgnCrossingEnable object." -- EdNote: add throttling limitations here, with 10 sec -- debouncing on clear to prevenmt intermittent alarms ::= { efmCuPmeNotifications 2 } efmCuPmeDeviceFault NOTIFICATION-TYPE OBJECTS { efmCuPmeFltStatus } STATUS current DESCRIPTION "This notification indicates that a fault in the PME has been detected by a vendor specific diagnostic or a self-test. Generation of this notification is controlled by the efmCuPmeDeviceFaultEnable object." ::= { efmCuPmeNotifications 3 } efmCuPmeConfigInitFailure NOTIFICATION-TYPE OBJECTS { efmCuPmeFltStatus, efmCuAdminProfile, efmCuPmeAdminProfile } STATUS current DESCRIPTION "This notification indicates that PME initialization has failed, due to inability of the PME link to achieve requested configuration profile. Generation of this notification is controlled by the efmCuPmeConfigInitFailEnable object." ::= { efmCuPmeNotifications 4 } efmCuPmeProtocolInitFailure NOTIFICATION-TYPE OBJECTS { efmCuPmeFltStatus, efmCuPmeOperSubType } STATUS current DESCRIPTION "This notification indicates that peer PME was using incompatible protocol during initialization. Generation of this notification is controlled by the efmCuPmeProtocolInitFailEnable object." ::= { efmCuPmeNotifications 5 } -- The PME group efmCuPmeConfTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPmeConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for Configuration of common aspects for EFMCu 2BASE-TL/10PASS-TS PME ports (modems). Configuration of aspects specific to 2BASE-TL or 10PASS-TS PME types is represented in efmCuPme2BConfTable and efmCuPme10PConfTable respectively. Entries in this table MUST be maintained in a persistent manner." ::= { efmCuPme 1 } efmCuPmeConfEntry OBJECT-TYPE SYNTAX EfmCuPmeConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu PME Configuration table. Each entry represents common aspects of an EFMCu PME port indexed by the ifIndex. Note that an EFMCu PME port can be stacked below a single PCS port, also indexed by ifIndex, possibly together with other PME ports if PAF is enabled." INDEX { ifIndex } ::= { efmCuPmeConfTable 1 } EfmCuPmeConfEntry ::= SEQUENCE { efmCuPmeAdminSubType INTEGER, efmCuPmeAdminProfile ProfileIndexOrZero, efmCuPAFRemoteDiscoveryCode PhysAddress, efmCuPmeThreshLineAtn Integer32, efmCuPmeThreshSnrMgn Integer32, efmCuPmeLineAtnCrossingEnable TruthValue, efmCuPmeSnrMgnCrossingEnable TruthValue, efmCuPmeDeviceFaultEnable TruthValue, efmCuPmeConfigInitFailEnable TruthValue, efmCuPmeProtocolInitFailEnable TruthValue } efmCuPmeAdminSubType OBJECT-TYPE SYNTAX INTEGER { ieee2BaseTLO(1), ieee2BaseTLR(2), ieee10PassTSO(3), ieee10PassTSR(4), ieee2BaseTLor10PassTSR(5), ieee2BaseTLor10PassTSO(6), ieee10PassTSor2BaseTLO(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative (desired) sub-type of the PME. Possible values are: ieee2BaseTLO - PME shall operate as 2BaseTL-O ieee2BaseTLR - PME shall operate as 2BaseTL-R ieee10PassTSO - PME shall operate as 10PassTS-O ieee10PassTSR - PME shall operate as 10PassTS-R ieee2BaseTLor10PassTSR - PME shall operate as 2BaseTL-R or 10PassTS-R. Actual value will be set by -O link partner during initialization (handshake). ieee2BaseTLor10PassTSO - PME shall operate as 2BaseTL-O (preferred) or 10PassTS-O. Actual value will be set during initialization depending on -R link partner capability (i.e. if -R is incapable of the preferred 2BaseTL mode, 10PassTS will be used). ieee10PassTSor2BaseTLO - PME shall operate as 10PassTS-O (preferred) or 2BaseTL-O. Actual value will be set during initialization depending on -R link partner capability (i.e. if -R is incapable of the preferred 10PassTS mode, 2BaseTL will be used). Changing efmCuPmeAdminSubType is a traffic disruptive operation and as such SHALL be done when the link is Down. Attempts to change this object SHALL be ignored if the link is Up or Initializing. Attempts to change this object to an unsupported subtype (see efmCuPmeSubTypesSupported) SHALL be rejected. The current operational sub type is indicated by efmCuPmeOperSubType variable. If a Clause 45 MDIO Interface to the PMA/PMD is present, then this object combines values of the Port sub-type select bits and the PMA/PMD type selection bits in the 10P/2B PMA/PMD control register" REFERENCE "[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7" ::= { efmCuPmeConfEntry 1 } efmCuPmeAdminProfile OBJECT-TYPE SYNTAX ProfileIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "Desired PME configuration Profile. This object is a pointer to an entry in either efmCuPme2BProfileTable or efmCuPme10PProfileTable, depending on the current operating SubType of the PME. The value of this object is the index of the referenced profile. The value of zero (default) indicates that the PME is configured via efmCuAdminProfile object for the PCS port, to which this PME is assigned. That is, the profile referenced by efmCuPmeAdminProfile takes precedence over the profile(s) referenced by efmCuAdminProfile. This object is writable and readable for the CO subtype PMEs (2BaseTL-O or 10PassTS-O). It is unavailable for the CPE subtype (2BaseTL-R or 10PassTS-R). Note that current operational Profile value is available via efmCuPmeOperProfile object. Modification of this object must be performed when the link is Down. Attempts to change this object MUST be rejected, if the link is Up or Initializing. Attempts to set this object to a value that is not the value of the index for an active entry in the corresponding profile table, MUST be rejected." REFERENCE "[802.3ah] 30.11.2.1.6" DEFVAL { 0 } ::= { efmCuPmeConfEntry 2 } efmCuPAFRemoteDiscoveryCode OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "PAF Remote Discovery Code of the PME port at CO. A 6 Byte long Discovery Code of the peer PCS connected via the PME. Reading this object results in a Discovery Get operation. Writing a zero to this object results in a Discovery Clear_if_Same operation (the value of efmCuPAFDiscoveryCode at the peer PCS shall be the same as efmCuPAFDiscoveryCode of the local PCS associated with the PME for the operation to succeed). Writing a non-zero value to this object results in a Discovery Set_if_Clear operation. This object does not exist in CPE port subtypes. A zero length octet string SHALL be returned for CPE port subtypes and also when PAF aggregation is not enabled. Discovery MUST be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. If a Clause 45 MDIO Interface to the PMA/PMD is present, then this object is a function of 10P/2B aggregation discovery control register, Discovery operation result bits in 10P/2B aggregation and discovery status register and 10P/2B aggregation discovery code register" REFERENCE "[802.3ah] 61.2.2.8.4, 45.2.6.6-45.2.6.8" ::= { efmCuPmeConfEntry 3 } efmCuPmeThreshLineAtn OBJECT-TYPE SYNTAX Integer32(-127..128) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Desired Line Attenuation Threshold for the 2B/10P PME. This object configures the line attenuation alarm threshold. When the current value of Line Attenuation reaches or exceeds this threshold, a efmCuPmeLineAtnCrossing notification MAY be generated, if enabled by efmCuPmeLineAtnCrossingEnable. This object is writable for the CO subtype PMEs (-O). It is read-only for the CPE subtype (-R). Changing of the Line Attenuation Threshold must be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. If a Clause 45 MDIO Interface to the PME is present, then this object will map to the Loop attenuation threshold bits in the 2B PMD line quality thresholds register" REFERENCE "[802.3ah] 45.2.1.36" ::= { efmCuPmeConfEntry 4 } efmCuPmeThreshSnrMgn OBJECT-TYPE SYNTAX Integer32(-127..128) UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Desired SNR Margin Threshold for the 2B/10P PME. This object configures the SNR margin alarm threshold. When the current value of SNR Margin reaches or exceeds this threshold, a efmCuPmeSnrMgnCrossing notification MAY be generated, if enabled by efmCuPmeSnrMgnCrossingEnable. This object is writable for the CO subtype PMEs (2BaseTL-O/10PassTS-R). It is read-only for the CPE subtype (2BaseTL-R/10PassTS-R). Changing of the SNR Margin Threshold must be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. If a Clause 45 MDIO Interface to the PME is present, then this object will map to the SNR margin threshold bits in the 2B PMD line quality thresholds register" REFERENCE "[802.3ah] 45.2.1.36" ::= { efmCuPmeConfEntry 5 } efmCuPmeLineAtnCrossingEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuPmeLineAtnCrossing notifications should be generated for this interface. Value of true(1) indicates that efmCuPmeLineAtnCrossing notification is enabled. Value of false(2) indicates that the notification is disabled." ::= { efmCuPmeConfEntry 6 } efmCuPmeSnrMgnCrossingEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuPmeSnrMgnCrossing notifications should be generated for this interface. Value of true(1) indicates that efmCuPmeSnrMgnCrossing notification is enabled. Value of false(2) indicates that the notification is disabled." ::= { efmCuPmeConfEntry 7 } efmCuPmeDeviceFaultEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuPmeDeviceFault notifications should be generated for this interface. Value of true(1) indicates that efmCuPmeDeviceFault notification is enabled. Value of false(2) indicates that the notification is disabled." ::= { efmCuPmeConfEntry 8 } efmCuPmeConfigInitFailEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuPmeConfigInitFailure notifications should be generated for this interface. Value of true(1) indicates that efmCuPmeConfigInitFailure notification is enabled. Value of false(2) indicates that the notification is disabled." ::= { efmCuPmeConfEntry 9 } efmCuPmeProtocolInitFailEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether efmCuPmeProtocolInitFailure notifications should be generated for this interface. Value of true(1) indicates that efmCuPmeProtocolInitFailure notification is enabled. Value of false(2) indicates that the notification is disabled." ::= { efmCuPmeConfEntry 10 } efmCuPmeCapabilityTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPmeCapabilityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for Configuration of common aspects for EFMCu 2BASE-TL/10PASS-TS PME ports (modems). Configuration of aspects specific to 2BASE-TL or 10PASS-TS PME types is represented in efmCuPme2BConfTable and efmCuPme10PConfTable respectively. Entries in this table MUST be maintained in a persistent manner." ::= { efmCuPme 2 } efmCuPmeCapabilityEntry OBJECT-TYPE SYNTAX EfmCuPmeCapabilityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu PME Capability table. Each entry represents common aspects of an EFMCu PME port indexed by the ifIndex. Note that an EFMCu PME port can be stacked below a single PCS port, also indexed by ifIndex, possibly together with other PME ports if PAF is enabled." INDEX { ifIndex } ::= { efmCuPmeCapabilityTable 1 } EfmCuPmeCapabilityEntry ::= SEQUENCE { efmCuPmeSubTypesSupported BITS } efmCuPmeSubTypesSupported OBJECT-TYPE SYNTAX BITS { ieee2BaseTLO(0), ieee2BaseTLR(1), ieee10PassTSO(2), ieee10PassTSR(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "PME supported sub-types. This is a bitmap of possible sub-types. The various bit positions are: ieee2BaseTLO - PME is capable of operating as 2BaseTL-O ieee2BaseTLR - PME is capable of operating as 2BaseTL-R ieee10PassTSO - PME is capable of operating as 10PassTS-O ieee10PassTSR - PME is capable of operating as 10PassTS-R An desired mode of operation is determined by efmCuPmeAdminSubType, while efmCuPmeOperSubType relects the current operating mode. If a Clause 45 MDIO Interface to the PCS is present, then this object combines the 10PASS-TS capable and 2BASE-TL capable bits in the 10P/2B PMA/PMD speed ability register and the CO supported and CPE supported bits in the 10P/2B PMA/PMD status register" REFERENCE "[802.3ah] 61.1, 45.2.1.4.1, 45.2.1.4.2, 45.2.1.12.2, 45.2.1.12.3" ::= { efmCuPmeCapabilityEntry 1 } efmCuPmeStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPmeStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides common status information of EFMCu 2BASE-TL/10PASS-TS PME ports. Status information specific to 10PASS-TS PME is represented in efmCuPme10PStatusTable. This table contains live data from the equipment. As such, it is NOT persistent." ::= { efmCuPme 3 } efmCuPmeStatusEntry OBJECT-TYPE SYNTAX EfmCuPmeStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu PME Status table. Each entry represents common aspects of an EFMCu PME port indexed by the ifIndex. Note that an EFMCu PME port can be stacked below a single PCS port, also indexed by ifIndex, possibly together with other PME ports if PAF is enabled." INDEX { ifIndex } ::= { efmCuPmeStatusTable 1 } EfmCuPmeStatusEntry ::= SEQUENCE { efmCuPmeOperStatus INTEGER, efmCuPmeFltStatus BITS, efmCuPmeOperSubType INTEGER, efmCuPmeOperProfile ProfileIndexOrZero, efmCuPmeSnrMgn Integer32, efmCuPmePeerSnrMgn Integer32, efmCuPmeLineAtn Integer32, efmCuPmePeerLineAtn Integer32, efmCuPmeTCCodingErrors Counter32, efmCuPmeTCCrcErrors Counter32 } efmCuPmeOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), downNotReady(2), downReady(3), init(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current PME link Operational Status. Possible values are: up(1) - link is Up and ready to pass 64/65B encoded frames or fragments. downNotReady(2) - link is Down and the PME does not detect Handshake tones from its peer. This value may indicate a possible problem with the peer PME. downReady(3) - link is Down and the PME detects Handshake tones from its peer. init(4) - link is initializing, as a result of ifAdminStatus being set to 'up' for a particular PME or a PCS the PME is connected to. This object is intended to supplement Down state of ifOperStatus. This object partially maps to the Clause 30 attribute aPMEStatus. If a Clause 45 MDIO Interface to the PME is present, then this object partially maps to PMA/PMD link status bits in 10P/2B PMA/PMD status register." REFERENCE "[802.3ah] 30.11.2.1.3, 45.2.1.12.4" ::= { efmCuPmeStatusEntry 1 } efmCuPmeFltStatus OBJECT-TYPE SYNTAX BITS { lossOfFraming(0), snrMgnDefect(1), lineAtnDefect(2), deviceFault(3), configInitFailure(4), protocolInitFailure(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current/Last PME link Fault Status. This is a bitmap of possible conditions. The various bit positions are: lossOfFraming - Loss of Framing for 10P or Loss of Sync word for 2B PMD or Loss of 64/65B Framing snrMgnDefect - SNR Margin dropped below the Threshold lineAtnDefect - Line Attenuation exceeds the Threshold deviceFault - Indicates a vendor-dependent diagnostic or self-test fault has been detected. configInitFailure - Configuration initialization failure, due to inability of the PME link to support configuration profile, requested during initialization. protocolInitFailure - Protocol initialization failure, due to incompatible protocol used by the Peer PME during init (that could happen if a peer PMD is G.SDHSL/VDSL modem for 2BASE-TL/10PASS-TS PME respectively). This object is intended to supplement ifOperStatus in IF-MIB. The indications hold information about the last fault. efmCuPmeFltStatus is cleared by the device restart. In addition lossOfFraming, configInitFailure and protocolInitFailure are cleared by PME init. deviceFault is cleared by successful diagnostics/test. snrMgnDefect and lineAtnDefect are cleared by SNR Margin and line Attenuation respectively returning to norm and by PME init. This object partially maps to the Clause 30 attribute aPMEStatus. If a Clause 45 MDIO Interface to the PME is present, then this object consolidates information from various PMA/PMD registers, namely: Fault bit in PMA/PMD status 1 register, 10P/2B PMA/PMD link loss register, 10P outgoing indicator bits status register, 10P incoming indicator bits status register, 2B state defects register." REFERENCE "[802.3ah] 30.11.2.1.3, 45.2.1.2.1, 45.2.1.38, 45.2.1.39, 45.2.1.54" ::= { efmCuPmeStatusEntry 2 } efmCuPmeOperSubType OBJECT-TYPE SYNTAX INTEGER { ieee2BaseTLO(1), ieee2BaseTLR(2), ieee10PassTSO(3), ieee10PassTSR(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current operational sub-type of the PME. Possible values are: ieee2BaseTLO - PME operates as 2BaseTL-O ieee2BaseTLR - PME operates as 2BaseTL-R ieee10PassTSO - PME operates as 10PassTS-O ieee10PassTSR - PME operates as 10PassTS-R The operational sub type of the PME can be configured via efmCuPmeAdminSubType variable. If a Clause 45 MDIO Interface to the PMA/PMD is present, then this object combines values of the Port sub-type select bits, the PMA/PMD type selection bits in the 10P/2B PMA/PMD control register and the PMA/PMD link status bits in the 10P/2B PMA/PMD status register." REFERENCE "[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7, 45.2.1.12.4" ::= { efmCuPmeStatusEntry 3 } efmCuPmeOperProfile OBJECT-TYPE SYNTAX ProfileIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "PME current operating Profile. This object is a pointer to an entry in either efmCuPme2BProfileTable or efmCuPme10PProfileTable, depending on the current operating SubType of the PME as indicated by efmCuPmeOperSubType. Note that a profile entry, to which efmCuPmeOperProfile is pointing to, can be created automatically, to reflect achieved parameters in adaptive (not fixed) initialization, i.e. values of efmCuPmeOperProfile and efmCuAdminProfile or efmCuPmeAdminProfile MAY differ. The value of zero indicates that PME is down or initializing. This object partially maps to the aOperatingProfile attribute in Clause 30." REFERENCE "[802.3ah] 30.11.2.1.7" ::= { efmCuPmeStatusEntry 4 } efmCuPmeSnrMgn OBJECT-TYPE SYNTAX Integer32(-127..128|65535) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current Signal-to-Noise Ratio (SNR) margin with respect to the received signal as perceived by the local PME. The value of 65535 is returned when PME is down or initializing. This object maps to the aPMESNRMgn attribute in Clause 30. If a Clause 45 MDIO Interface is present, then this object maps to the 10P/2B RX SNR margin register." REFERENCE "[802.3ah] 30.11.2.1.4, 45.2.1.16" ::= { efmCuPmeStatusEntry 5 } efmCuPmePeerSnrMgn OBJECT-TYPE SYNTAX Integer32(-127..128|65535) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current SNR margin in dB with respect to the received signal, as perceived by the remote (link partner) PME. The value of 65535 is returned when PME is down or initializing. This object is not supported by -R PME subtypes. If a Clause 45 MDIO Interface is present, then this object maps to the 10P/2B link partner RX SNR margin register." REFERENCE "[802.3ah] 45.2.1.17" ::= { efmCuPmeStatusEntry 6} efmCuPmeLineAtn OBJECT-TYPE SYNTAX Integer32(-127..128|65535) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current Line Attenuation in dB as perceived by the local PME. The value of 65535 is returned when PME is down or initializing. If a Clause 45 MDIO Interface is present, then this object maps to the Line Attenuation register" REFERENCE "[802.3ah] 45.2.1.18" ::= { efmCuPmeStatusEntry 7 } efmCuPmePeerLineAtn OBJECT-TYPE SYNTAX Integer32(-127..128|65535) UNITS "dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The current Line Attenuation in dB as perceived by the remote (link partner) PME. The value of 65535 is returned when PME is down or initializing. This object is not supported by CPE port subtypes. If a Clause 45 MDIO Interface is present, then this object maps to the 20P/2B link partner Line Attenuation register." REFERENCE "[802.3ah] 45.2.1.19" ::= { efmCuPmeStatusEntry 8 } efmCuPmeTCCodingErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of 64/65-octet encapsulation errors. This counter is incremented for each 64/65-octet encapsulation error detected by the 64/65-octet receive function. The value of zero SHALL be returned when PME is down or initializing. If a Clause 45 MDIO Interface to the PME TC is present, then this object maps to the TC coding violations register (see 45.2.6.12)." REFERENCE "[802.3ah] 61.3.3.1, 45.2.6.12" ::= { efmCuPmeStatusEntry 9 } efmCuPmeTCCrcErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A number of TC-CRC errors. This counter is incremented for each TC-CRC error detected by the 64/65-octet receive function (see 61.3.3.3 and Figure 61-19). The value of zero SHALL be returned when PME is down or initializing. If a Clause 45 MDIO Interface to the PCME TC is present, then this object maps to the TC CRC error register (see 45.2.6.11)." REFERENCE "[802.3ah] 61.3.3.3, 45.2.6.11" ::= { efmCuPmeStatusEntry 10 } -- 2BASE-TL specific PME group efmCuPme2B OBJECT IDENTIFIER ::= { efmCuPme 5 } efmCuPme2BProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPme2BProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports definitions of administrative and operating Profiles for 2BASE-TL PMEs. First 14 entries in this table SHALL always be defined as follows (see 802.3ah Annex 63A): -------+------+-----+--------+------------------ Profile Rate Power Region Constellation index (Kbps) (dBm) (G.991.2) -------+------+-----+--------+------------------ 1 5696 13.5 1 32-TCPAM (default) 2 3072 13.5 1 32-TCPAM 3 2048 13.5 1 16-TCPAM 4 1024 13.5 1 16-TCPAM 5 704 13.5 1 16-TCPAM 6 512 13.5 1 16-TCPAM 7 5696 14.5 2 32-TCPAM 8 3072 14.5 2 32-TCPAM 9 2048 14.5 2 16-TCPAM 10 1024 13.5 2 16-TCPAM 11 704 13.5 2 16-TCPAM 12 512 13.5 2 16-TCPAM 13 0 0 1 0 (best effort) 14 0 0 2 0 (best effort) These default entries SHALL be created during agent initialization and MUST not be deleted. Entries following the first 14, can be dynamically created and deleted, to provide custom administrative (configuration) profiles and automatic operating profiles. This table MUST be maintained in a persistent manner." REFERENCE "[802.3ah] Annex 63A, 30.11.2.1.6" ::= { efmCuPme2B 2 } efmCuPme2BProfileEntry OBJECT-TYPE SYNTAX EfmCuPme2BProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry corresponds to a single 2BASE-TL PME profile. Each profile contains a set of parameters, used either for configuration or representation of a 2BASE-TL PME. In case a particular profile is referenced via efmCuPmeAdminProfile object (or efmCuAdminProfile if efmCuPmeAdminProfile is zero), it represent the desired parameters the 2BaseTL-O PME initialization. If a profile is referenced via efmCuPmeOperProfile object, it represents current operating parameters of the operational PME. Profiles may be created/deleted using the row creation/ deletion mechanism via efmCuPme2BProfileRowStatus. If an active entry is referenced, the entry MUST remain 'active' until all references are removed. Default entries MUST not be removed." INDEX { efmCuPme2BProfileIndex } ::= { efmCuPme2BProfileTable 1 } EfmCuPme2BProfileEntry ::= SEQUENCE { efmCuPme2BProfileIndex ProfileIndex, efmCuPme2BProfileDescr SnmpAdminString, efmCuPme2BRegion INTEGER, efmCuPme2BDataRate Unsigned32, efmCuPme2BPower Unsigned32, efmCuPme2BConstellation INTEGER, efmCuPme2BProfileRowStatus RowStatus } efmCuPme2BProfileIndex OBJECT-TYPE SYNTAX ProfileIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "2BASE-TL PME Profile index. This object is the unique index associated with this profile. Entries in this table are referenced via efmCuAdminProfile or efmCuPmeAdminProfile objects." ::= { efmCuPme2BProfileEntry 1 } efmCuPme2BProfileDescr OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about 2BASE-TL PME Profile. The string MAY include information about data rate and spectral limitations of this particular profile." ::= { efmCuPme2BProfileEntry 2 } efmCuPme2BRegion OBJECT-TYPE SYNTAX INTEGER { region1(1), region2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Power Spectral Density (PSD) Regional settings as specified in the relevant Regional Annex of [G.991.2]. Regional settings place limitations on the max allowed data rate, power and constellation. Possible values for this object are: region1 -- Annexes A and F (e.g. North America) region2 -- Annexes B and G (e.g. Europe) Changing of the Region must be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. If a Clause 45 MDIO Interface to the PME is present, then this object maps to the Region bits in the 2B general parameter register." REFERENCE "[802.3ah] 45.2.1.42" ::= { efmCuPme2BProfileEntry 3 } efmCuPme2BDataRate OBJECT-TYPE SYNTAX Unsigned32(0..5696) UNITS "Kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "2BASE-TL PME Data Rate. The rate is fixed when the value of this object is n x 64Kbps, where n=3..60 for 16-TCPAM and n=12..89 for 32-TCPAM. The value of 0 in the administrative profile means that data rate is not fixed but is adaptive and should be set to the maximum attainable rate during line probing, under the spectral limitations placed by the efmCuPme2BRegion. If a Clause 45 MDIO Interface to the PME is present, then this object maps to the Min/Max Data Rate1 bits in the 2B PMD parameters register. This object MUST be maintained in a persistent manner." REFERENCE "[802.3ah] 45.2.1.43" ::= { efmCuPme2BProfileEntry 4 } efmCuPme2BPower OBJECT-TYPE SYNTAX Unsigned32(0|10..42) UNITS "0.5 dBm" MAX-ACCESS read-create STATUS current DESCRIPTION "Signal Transmit Power. Multiple of 0.5dBm. The value of 0 in the administrative profile means that the signal transmit power is not fixed and should be set to maximize the attainable rate, under the spectral limitations placed by the efmCuPme2BRegion. Changing of the Signal Transmit Power must be performed when the link is Down. Attempts to change this object MUST be rejected with the error inconsistentValue, if the link is Up or Initializing. If a Clause 45 MDIO Interface to the PME is present, then this object will map to the Power1 bits in the 2B PMD parameters register" REFERENCE "[802.3ah] 45.2.1.43" ::= { efmCuPme2BProfileEntry 5 } efmCuPme2BConstellation OBJECT-TYPE SYNTAX INTEGER { adaptive(0), tcpam16(1), tcpam32(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "TCPAM Constellation of the 2BASE-TL PME. The possible values are: adaptive(0) - either 16- or 32-TCPAM tcpam16(1) - 16-TCPAM tcpam32(2) - 32-TCPAM The value of adaptive(0) in the administrative profile means that the constellation is not fixed and should be set to maximize the attainable rate, under the spectral limitations placed by the efmCuPme2BRegion. If a Clause 45 MDIO Interface to the PME is present, then this object map to the Constellation1 bits in the 2B general parameter register." REFERENCE "[802.3ah] 45.2.1.43" ::= { efmCuPme2BProfileEntry 6 } efmCuPme2BProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls creation/deletion of the associated entry in efmCuPme2BProfileTable per the semantics of RowStatus. If an 'active' entry is referenced via efmCuAdminProfile or efmCuPmeAdminProfile, the entry MUST remain 'active' until all references are removed." ::= { efmCuPme2BProfileEntry 7 } -- 10PASS-TS specific PME group efmCuPme10P OBJECT IDENTIFIER ::= { efmCuPme 6 } efmCuPme10PProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPme10PProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports definitions of configuration profiles for 10PassTL PMEs. First 22 entries in this table SHALL always be defined as follows (see 802.3ah Annex 62B.3): -------+--------+----+---------+-----+------------ Profile Bandplan UPBO BandNotch DRate URate Index PSDMask# p# p# p# p# -------+--------+----+---------+-----+------------ 1 1 3 2,6,10,11 20 20(default) 2 13 5 0 20 20 3 1 1 0 20 20 4 16 0 0 100 100 5 16 0 0 70 50 6 6 0 0 50 10 7 17 0 0 30 30 8 8 0 0 30 5 9 4 0 0 25 25 10 4 0 0 15 15 11 23 0 0 10 10 12 23 0 0 5 5 13 16 0 2,5,9,11 100 100 14 16 0 2,5,9,11 70 50 15 6 0 2,6,10,11 50 10 16 17 0 2,5,9,11 30 30 17 8 0 2,6,10,11 30 5 18 4 0 2,6,10,11 25 25 19 4 0 2,6,10,11 15 15 20 23 0 2,5,9,11 10 10 21 23 0 2,5,9,11 5 5 22 30 0 0 200 50 These default entries SHALL be created by during agent initialization and MUST not be deleted. Entries following the first 22, can be dynamically created and deleted, to provide custom administrative (configuration) profiles and automatic operating profiles. This table MUST be maintained in a persistent manner." REFERENCE "[802.3ah] Annex 62B.3, 30.11.2.1.6" ::= { efmCuPme10P 1 } efmCuPme10PProfileEntry OBJECT-TYPE SYNTAX EfmCuPme10PProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry corresponds to a single 10PASS-TS PME profile. Each profile contains a set of parameters, used either for configuration or representation of a 10PASS-TS PME. In case a particular profile is referenced via efmCuPmeAdminProfile object (or efmCuAdminProfile if efmCuPmeAdminProfile is zero), it represent the desired parameters the 10PassTS-O PME initialization. If a profile is referenced via efmCuPmeOperProfile object, it represents current operating parameters of the PME. Profiles may be created/deleted using the row creation/ deletion mechanism via efmCuPme10PProfileRowStatus. If an 'active' entry is referenced, the entry MUST remain 'active' until all references are removed. Default entries MUST not be removed." INDEX { efmCuPme10PProfileIndex } ::= { efmCuPme10PProfileTable 1 } EfmCuPme10PProfileEntry ::= SEQUENCE { efmCuPme10PProfileIndex ProfileIndex, efmCuPme10PProfileDescr SnmpAdminString, efmCuPme10PBandplanPSDMskProfile INTEGER, efmCuPme10PUPBOReferenceProfile INTEGER, efmCuPme10PBandNotchProfiles BITS, efmCuPme10PPayloadURateProfile INTEGER, efmCuPme10PPayloadDRateProfile INTEGER, efmCuPme10PProfileRowStatus RowStatus } efmCuPme10PProfileIndex OBJECT-TYPE SYNTAX ProfileIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "10PASS-TS PME Profile Index. This object is the unique index associated with this profile. Entries in this table are referenced via efmCuAdminProfile or efmCuPmeAdminProfile." ::= { efmCuPme10PProfileEntry 1 } efmCuPme10PProfileDescr OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about 10PASS-TS PME Profile. The string MAY include information about data rate and spectral limitations of this particular profile." ::= { efmCuPme10PProfileEntry 2 } efmCuPme10PBandplanPSDMskProfile OBJECT-TYPE SYNTAX INTEGER { profile1(1), profile2(2), profile3(3), profile4(4), profile5(5), profile6(6), profile7(7), profile8(8), profile9(9), profile10(10), profile11(11), profile12(12), profile13(13), profile14(14), profile15(15), profile16(16), profile17(17), profile18(18), profile19(19), profile20(20), profile21(21), profile22(22), profile23(23), profile24(24), profile25(25), profile26(26), profile27(27), profile28(28), profile29(29) } MAX-ACCESS read-create STATUS current DESCRIPTION "10PASS-TS PME Bandplan and PSD Mask profile, as specified in 802.3ah Annex 62A. Possible values are: --------------+------------------------+-----------+--------- Profile Name PSD Mask Bands Bandplan --------------+------------------------+-----------+--------- profile1(1) - T1.424/T-U P1 FTTCab.M1 x/D/U/D/U A profile2(2) - T1.424/T-U P1 FTTEx.M1 profile3(3) - T1.424/T-U P1 FTTCab.M2 profile4(4) - T1.424/T-U P1 FTTEx.M2 profile5(5) - T1.424/T-U P1 FTTCab.M1 D/D/U/D/U profile6(6) - T1.424/T-U P1 FTTEx.M1 profile7(7) - T1.424/T-U P1 FTTCab.M2 profile8(8) - T1.424/T-U P1 FTTEx.M2 profile9(9) - T1.424/T-U P1 FTTCab.M1 U/D/U/D/x profile10(10) - T1.424/T-U P1 FTTEx.M1 profile11(11) - T1.424/T-U P1 FTTCab.M2 profile12(12) - T1.424/T-U P1 FTTEx.M2 profile13(13) - TS1 101 270-1 Pcab.M1.A x/D/U/D/U B profile14(14) - TS1 101 270-1 Pcab.M1.B profile15(15) - TS1 101 270-1 Pex.P1.M1 profile16(16) - TS1 101 270-1 Pex.P2.M1 profile17(17) - TS1 101 270-1 Pcab.M2 profile18(18) - TS1 101 270-1 Pex.P1.M2 profile19(19) - TS1 101 270-1 Pex.P2.M2 profile20(20) - TS1 101 270-1 Pcab.M1.A U/D/U/D/x profile21(21) - TS1 101 270-1 Pcab.M1.B profile22(22) - TS1 101 270-1 Pex.P1.M1 profile23(23) - TS1 101 270-1 Pex.P2.M1 profile24(24) - TS1 101 270-1 Pcab.M2 profile25(25) - TS1 101 270-1 Pex.P1.M2 profile26(26) - TS1 101 270-1 Pex.P2.M2 profile27(27) - G.993.1 F.1.2.1 (VDSLoPOTS) x/D/U/D/U F profile28(28) - G.993.1 F.1.2.2 (VDSLoTCM-ISDN) profile29(29) - G.993.1 F.1.2.3 (PSD reduction) This object maps to the aBandplanPSDMaskProfile attribute in Clause 30." REFERENCE "[802.3ah] Annex 62A, 30.5.1.1.22" ::= { efmCuPme10PProfileEntry 3 } efmCuPme10PUPBOReferenceProfile OBJECT-TYPE SYNTAX INTEGER { profile1(1), profile2(2), profile3(3), profile4(4), profile5(5), profile6(6), profile7(7), profile8(8), profile9(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "10PASS-TS PME Upstream Power Back-Off (UPBO) Reference PSD Profile, as specified in 802.3ah Annex 62A. Possible values are: profile1(1) - T1.424/T-U Noise A M1 profile2(2) - T1.424/T-U Noise A M2 profile3(3) - T1.424/T-U Noise F M1 profile4(4) - T1.424/T-U Noise F M2 profile5(5) - ETSI TS 101 270-1 Noise A&B profile6(6) - ETSI TS 101 270-1 Noise C profile7(7) - ETSI TS 101 270-1 Noise D profile8(8) - ETSI TS 101 270-1 Noise E profile9(9) - ETSI TS 101 270-1 Noise F This object maps to the aUPBOReferenceProfile attribute in Clause 30." REFERENCE "[802.3ah] Annex 62A.3.4, 30.5.1.1.23" ::= { efmCuPme10PProfileEntry 4 } efmCuPme10PBandNotchProfiles OBJECT-TYPE SYNTAX BITS { profile0(0), profile1(1), profile2(2), profile3(3), profile4(4), profile5(5), profile6(6), profile7(7), profile8(8), profile9(9), profile10(10), profile11(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "10PASS-TS PME Egress Control Band Notch Profile bitmap, as specified in 802.3ah Annex 62A. Possible values are: --------------+---------+----------+-----------+------+----- Profile Name G.991.3 T1.424/T-U TS101 270-1 StartF EndF Table Table Table (MHz) (MHz) --------------+---------+----------+-----------+------+----- profile0(0) - no profile profile1(1) - F-5 #01 - - 1.810 1.825 profile2(2) - 6-2 15-1 17 1.810 2.000 profile3(3) - F-5 #02 - - 1.907 1.912 profile4(4) - F-5 #03 - - 3.500 3.575 profile5(5) - 6-2 - 17 3.500 3.800 profile6(6) - - 15-1 - 3.500 4.000 profile7(7) - F-5 #04 - - 3.747 3.754 profile8(8) - F-5 #05 - - 3.791 3.805 profile9(9) - 6-2 - 17 7.000 7.100 profile10(10) - F-5 #06 15-1 - 7.000 7.300 profile11(11) - 6-2 15-1 1 10.100 10.150 Any combination of profiles can be specified by ORing individual profiles, for example value of 0x0622 selects profiles 2,6,10 and 11. This object maps to the aBandNotchProfile attribute in Clause 30." REFERENCE "[802.3ah] Annex 62A.3.5, 30.5.1.1.19" ::= { efmCuPme10PProfileEntry 5 } efmCuPme10PPayloadURateProfile OBJECT-TYPE SYNTAX INTEGER { profile5(5), profile10(10), profile15(15), profile20(20), profile25(25), profile30(30), profile50(50), profile70(70), profile100(100) } MAX-ACCESS read-create STATUS current DESCRIPTION "10PASS-TS PME Upstream Payload Rate Profile, as specified in 802.3ah Annex 62A. Possible values are: profile5(5) - 2.5 Mbps profile10(10) - 5 Mbps profile15(15) - 7.5 Mbps profile20(20) - 10 Mbps profile25(25) - 12.5 Mbps profile30(30) - 15 Mbps profile50(50) - 25 Mbps profile70(70) - 35 Mbps profile100(100) - 50 Mbps Each value represents a target for the PME's Upstream Payload Bitrate as seen at the MII. If the payload rate of the selected profile cannot be achieved based on the loop environment, bandplan and PSD mask, the PME initialization SHALL fail. This object maps to the aPayloadRateProfileUpstream attribute in Clause 30." REFERENCE "[802.3ah] Annex 62A.3.6, 30.5.1.1.20" ::= { efmCuPme10PProfileEntry 6 } efmCuPme10PPayloadDRateProfile OBJECT-TYPE SYNTAX INTEGER { profile5(5), profile10(10), profile15(15), profile20(20), profile25(25), profile30(30), profile50(50), profile70(70), profile100(100), profile140(140), profile200(200) } MAX-ACCESS read-create STATUS current DESCRIPTION "10PASS-TS PME Downstream Payload Rate Profile, as specified in 802.3ah Annex 62A. Possible values are: profile5(5) - 2.5 Mbps profile10(10) - 5 Mbps profile15(15) - 7.5 Mbps profile20(20) - 10 Mbps profile25(25) - 12.5 Mbps profile30(30) - 15 Mbps profile50(50) - 25 Mbps profile70(70) - 35 Mbps profile100(100) - 50 Mbps profile140(140) - 70 Mbps profile200(200) - 100 Mbps Each value represents a target for the PME's Downstream Payload Bitrate as seen at the MII. If the payload rate of the selected profile cannot be achieved based on the loop environment, bandplan and PSD mask, the PME initialization SHALL fail. This object maps to the aPayloadRateProfileDownstream attribute in Clause 30." REFERENCE "[802.3ah] Annex 62A.3.6, 30.5.1.1.21" ::= { efmCuPme10PProfileEntry 7 } efmCuPme10PProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls creation/deletion of the associated entry in efmCuPme10PProfileTable per the semantics of RowStatus. If an active entry is referenced via efmCuAdminProfile or efmCuPmeAdminProfile, the entry MUST remain 'active' until all references are removed." ::= { efmCuPme10PProfileEntry 8 } efmCuPme10PStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF EfmCuPme10PStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table reflecting status of EFMCu 10PASS-TS PMEs (modems)." ::= { efmCuPme10P 2 } efmCuPme10PStatusEntry OBJECT-TYPE SYNTAX EfmCuPme10PStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EFMCu 10PASS-TS PME Status table." AUGMENTS { efmCuPmeStatusEntry } ::= { efmCuPme10PStatusTable 1 } EfmCuPme10PStatusEntry ::= SEQUENCE { efmCuPme10PElectricalLength Integer32, efmCuPme10PFECCorrectedBlocks Counter32, efmCuPme10PFECUncorrectedBlocks Counter32 -- EdNote: To be continued } efmCuPme10PElectricalLength OBJECT-TYPE SYNTAX Integer32(0..8192|65535) UNITS "m" MAX-ACCESS read-only STATUS current DESCRIPTION "Electrical Length in meters as perceived by the 10PASS-TS PME after the link is established. The value of 65535 is returned if the link is Down or Initializing or the PME is unable to estimate the Electrical Length. If a Clause 45 MDIO Interface to the PME is present, then this object maps to the 10P Electrical Length register" REFERENCE "[802.3ah] 45.2.1.21" ::= { efmCuPme10PStatusEntry 1 } efmCuPme10PFECCorrectedBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of received and corrected FEC codewords in 10PASS-TS PME. This object maps to aPMEFECCorrectedBlocks attribute in clause 30. If a Clause 45 MDIO Interface to the PMA/PMD is present, then this object maps to the 10P FEC correctable errors register" REFERENCE "[802.3ah] 45.2.1.22" ::= { efmCuPme10PStatusEntry 2 } efmCuPme10PFECUncorrectedBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of received FEC codewords in 10PASS-TS PME, which are uncorrectable. This object maps to aPMEFECUncorrectableBlocks attribute in clause 30. If a Clause 45 MDIO Interface to the PMA/PMD is present, then this object maps to the 10P FEC uncorrectable errors register" REFERENCE "[802.3ah] 45.2.1.23" ::= { efmCuPme10PStatusEntry 3 } -- ifAvailableStackTable for use in Discovery ifAvailableStackTable OBJECT-TYPE SYNTAX SEQUENCE OF IfAvailableStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table, modeled after ifStackTable from [IF-MIB], contains information on the possible 'on-top-of' relationships between the multiple sub-layers of network interfaces (as opposed to actual relationships in ifStackTable). In particular, it contains information on which PCS ports (sublayers) can possibly run 'on top of' which PMEs (sublayers), as determined by cross-connect capability of the EFMCu device, where each sub-layer corresponds to a conceptual row in the ifTable. For example, when the PCS port with ifIndex value x can be connected to run on top of the PME with ifIndex value y, then this table contains: ifAvailableStackStatus.x.y=capable Note that there's always at least on PCS for each PME and at least one PME for each PCS in the EFMCu devices, with efmCuPAFCapacity and efmCuPeerPAFCapacity indicating maximum number of PMEs which can be aggregated by local and remote PCS port respectively. This table is read only as it describes device capability" REFERENCE "ifStackTable of RFC 2863" ::= { efmCuObjects 3 } ifAvailableStackEntry OBJECT-TYPE SYNTAX IfAvailableStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information on a particular relationship between two sub-layers, specifying that one sub-layer (PCS) runs on 'top' of the other sub-layer (PME). Each sub-layer corresponds to a conceptual row in the ifTable (interface index for PCS and PME respectively)." INDEX { ifAvailableStackHigherLayer, ifAvailableStackLowerLayer } ::= { ifAvailableStackTable 1 } IfAvailableStackEntry ::= SEQUENCE { ifAvailableStackHigherLayer InterfaceIndex, ifAvailableStackLowerLayer InterfaceIndex, ifAvailableStackStatus INTEGER } ifAvailableStackHigherLayer OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of ifIndex corresponding to the higher sub-layer of the 'cross-connect capability' relationship, i.e., the PCS sub-layer which MAY run on 'top' of the PME sub-layer identified by the corresponding instance of ifAvailableStackLowerLayer." ::= { ifAvailableStackEntry 1 } ifAvailableStackLowerLayer OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of ifIndex corresponding to the lower sub-layer of the 'cross-connect capability' relationship, i.e., the PME sub-layer which MAY run 'below' the PCS sub-layer identified by the corresponding instance of ifAvailableStackHigherLayer." ::= { ifAvailableStackEntry 2 } ifAvailableStackStatus OBJECT-TYPE SYNTAX INTEGER { capable(1), outOfService(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the 'cross-connect capability' relationship between two sub-layers. The following values are defined: capable(1) - the PME sub-layer interface, identified by the ifAvailableStackLowerLayer MAY be connected to run 'below' the PCS sub-layer interface, identified by the ifAvailableStackLowerLayer. outOfService(2) - the PME sub-layer interface cannot be connected due to unavailability of the interface. Note that PME availability per PCS, indicated by 'capable' value, can be constrained by other parameters, for example by aggregation capacity of a PCS or by the PME in question being already connected to another PCS. So, in order to ensure that a particular PME can be connected to the PCS, all respective parameters (e.g. ifAvailableStackTable, ifStackTable and efmCuPAFCapacity) SHALL be inspected. This object is read only, unlike ifStackStatus, as it describes the device capability." ::= { ifAvailableStackEntry 3 } -- -- Conformance Statements -- efmCuGroups OBJECT IDENTIFIER ::= { efmCuConformance 1 } efmCuCompliances OBJECT IDENTIFIER ::= { efmCuConformance 2 } -- Object Groups efmCuBasicGroup OBJECT-GROUP OBJECTS { efmCuPAFSupported, efmCuAdminProfile, efmCuTargetDataRate, efmCuTargetSnrMgn, efmCuPortSide, efmCuFltStatus } STATUS current DESCRIPTION "A collection of objects required for all of EFMCu ports." ::= { efmCuGroups 1 } efmCuPAFGroup OBJECT-GROUP OBJECTS { efmCuPeerPAFSupported, efmCuPAFCapacity, efmCuPeerPAFCapacity, efmCuPAFAdminState, efmCuPAFDiscoveryCode, efmCuPAFRemoteDiscoveryCode, efmCuNumPMEs, ifAvailableStackStatus } STATUS current DESCRIPTION "A collection of objects required for optional PME Aggregation Function (PAF) and PAF discovery in EFMCu ports." ::= { efmCuGroups 2 } ifStackCapabilityGroup OBJECT-GROUP OBJECTS { ifAvailableStackStatus } STATUS current DESCRIPTION "A collection of objects providing information on the stacking capability of MIB-II interfaces." ::= { efmCuGroups 3 } efmCuPAFErrorsGroup OBJECT-GROUP OBJECTS { efmCuPAFInErrors, efmCuPAFInSmallFragments, efmCuPAFInLargeFragments, efmCuPAFInBadFragments, efmCuPAFInLostFragments, efmCuPAFInLostStarts, efmCuPAFInLostEnds, efmCuPAFInOverflows } STATUS current DESCRIPTION "A collection of objects supporting optional error counters of PAF on EFMCu ports." ::= { efmCuGroups 4 } efmCuPmeGroup OBJECT-GROUP OBJECTS { efmCuPmeAdminProfile, efmCuPmeOperStatus, efmCuPmeFltStatus, efmCuPmeSubTypesSupported, efmCuPmeAdminSubType, efmCuPmeOperSubType, efmCuPAFRemoteDiscoveryCode, efmCuPmeOperProfile, efmCuPmeSnrMgn, efmCuPmePeerSnrMgn, efmCuPmeLineAtn, efmCuPmePeerLineAtn, efmCuPmeTCCodingErrors, efmCuPmeTCCrcErrors, efmCuPmeThreshLineAtn, efmCuPmeThreshSnrMgn } STATUS current DESCRIPTION "A collection of objects providing information about a 2BASE-TL/10PASS-TS PME." ::= { efmCuGroups 5 } efmCuAlarmConfGroup OBJECT-GROUP OBJECTS { efmCuThreshLowBandwidth, efmCuLowBandwidthEnable, efmCuPmeThreshLineAtn, efmCuPmeLineAtnCrossingEnable, efmCuPmeThreshSnrMgn, efmCuPmeSnrMgnCrossingEnable, efmCuPmeLineAtnCrossingEnable, efmCuPmeDeviceFaultEnable, efmCuPmeConfigInitFailEnable, efmCuPmeProtocolInitFailEnable -- efmCuPmeThreshES, -- efmCuPmethreshSES, -- efmCuPmeThreshCRCanomalies, -- efmCuPmeThreshLOSWS, -- efmCuPmeThreshUAS } STATUS current DESCRIPTION "A collection of objects required for configuration of alarm thresholds and notifications in EFMCu ports." ::= { efmCuGroups 6 } efmCuNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { efmCuLowBandwidth, efmCuPmeLineAtnCrossing, efmCuPmeSnrMgnCrossing, efmCuPmeDeviceFault, efmCuPmeConfigInitFailure, efmCuPmeProtocolInitFailure -- efmCuPmePerfES, -- efmCuPmePerfSES, -- efmCuPmePerfCRCanomalies, -- efmCuPmePerfLOSWS, -- efmCuPmePerfUAS, -- efmCuPmeDeviceFault, -- efmCuPmeLocalPowerLoss } STATUS current DESCRIPTION "This group supports notifications of significant conditions associated with EFMCu ports." ::= { efmCuGroups 7 } efmCuPme2BProfileGroup OBJECT-GROUP OBJECTS { efmCuPme2BProfileDescr, efmCuPme2BRegion, efmCuPme2BDataRate, efmCuPme2BPower, efmCuPme2BConstellation, efmCuPme2BProfileRowStatus } STATUS current DESCRIPTION "A collection of objects that constitute a configuration profile for configuration of 2BASE-TL ports." ::= { efmCuGroups 8 } efmCuPme10PProfileGroup OBJECT-GROUP OBJECTS { efmCuPme10PProfileDescr, efmCuPme10PBandplanPSDMskProfile, efmCuPme10PUPBOReferenceProfile, efmCuPme10PBandNotchProfiles, efmCuPme10PPayloadURateProfile, efmCuPme10PPayloadDRateProfile, efmCuPme10PProfileRowStatus } STATUS current DESCRIPTION "A collection of objects that constitute a configuration profile for configuration of 10PASS-TS ports." ::= { efmCuGroups 9 } efmCuPme10PStatusGroup OBJECT-GROUP OBJECTS { efmCuPme10PElectricalLength, efmCuPme10PFECCorrectedBlocks, efmCuPme10PFECUncorrectedBlocks } STATUS current DESCRIPTION "A collection of objects providing status information specific to 10PASS-TS PMEs." ::= { efmCuGroups 10 } -- Compliance Statements efmCuCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for 2BASE-TL/10PASS-TS interfaces. Compliance with the following external compliance statements is prerequisite: MIB Module Compliance Statement ---------- -------------------- IF-MIB ifCompliance3 IF-INVERTED-STACK-MIB ifInvCompliance EtherLike-MIB dot3Compliance2 MAU-MIB mauModIfCompl3" MODULE -- this module MANDATORY-GROUPS { efmCuBasicGroup, efmCuPmeGroup, efmCuAlarmConfGroup, efmCuNotificationGroup } GROUP efmCuPme2BProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting 2BASE-TL Phy." GROUP efmCuPme10PProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting 10PASS-TS Phy." GROUP efmCuPAFGroup DESCRIPTION "Support for this group is only required for implementations supporting PME Aggregation Function (PAF)." GROUP ifStackCapabilityGroup DESCRIPTION "Support for this group is optional for implementations supporting layered interfaces architecture with flexible cross-connect between the layers." GROUP efmCuPAFErrorsGroup DESCRIPTION "Support for this group is optional for implementations supporting PME Aggregation Function (PAF)." GROUP efmCuPme10PStatusGroup DESCRIPTION "Support for this group is optional for implementations supporting 10PASS-TS Phy." OBJECT efmCuPmeSubTypesSupported SYNTAX BITS { ieee2BaseTLO(0), ieee2BaseTLR(1), ieee10PassTSO(2), ieee10PassTSR(3) } DESCRIPTION "Support for all subtypes is not required. However at least one value SHALL be supported" OBJECT efmCuPmeAdminSubType MIN-ACCESS read-only DESCRIPTION "Write access is not required (needed only for PMEs supporting more than a single subtype, e.g. ieee2BaseTLO and ieee2BaseTSR or ieee2BaseTLR and ieee10PassTSR)" OBJECT efmCuTargetSnrMgn MIN-ACCESS read-only DESCRIPTION "Write access is optional. For PHYs without write access the target SNR margin SHALL be fixed at 5dB for 2BASE-TL and 6dB for 10PASS-TS." -- EdNote: To be Continued ::= { efmCuCompliances 1 } END -- -- Copyright (C) The Internet Society (2005). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- -- Acknowledgment -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society.