-- extracted from draft-ietf-frnetmib-mfrmib-01.txt -- at Fri Mar 17 12:29:47 2000 FRF16-MFR-MIB-EXP DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, NOTIFICATION-TYPE, experimental FROM SNMPv2-SMI TEXTUAL-CONVENTION, TestAndIncr, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB InterfaceIndex, ifIndex FROM IF-MIB; mfrMib MODULE-IDENTITY LAST-UPDATED "0003090000Z" ORGANIZATION "IETF Frame Relay Service MIB (frnetmib) Working Group" CONTACT-INFO "WG Charter: http://www.ietf.org/html.charters/frnetmib-charter.html WG-email: frnetmib@sunroof.eng.sun.com Subscribe: frnetmib-request@sunroof.eng.sun.com Email Archive: ftp://ftp.ietf.org/ietf-mail-archive/frnetmib Chair: Andy Malis Lucent Technologies Email: amalis@lucent.com WG editor: Prayson Pate Larscom Email: pate@larscom.com Co-author: Bob Lynch Larscom EMail: blynch@larscom.com Co-author: Kenneth Rehbehn Visual Networks EMail: krehbehn@visualnetworks.com" DESCRIPTION "This is the MIB used to control and monitor the multilink frame relay (MFR) function described in FRF.16. This was originally submitted to the Frame Relay Forum as contribution FRFTC 99-151 and then updated as FRFTC 99-193." -- --------------------------------------------------------- -- --------------------------------------------------------- -- Revision History -- --------------------------------------------------------- -- --------------------------------------------------------- REVISION "0003090000Z" DESCRIPTION "Initial version of the FRF.16 UNI/NNI Multilink Frame Relay MIB. Published as RFC [RFC-EDITOR: Enter RFC # here]." REVISION "0003090000Z" DESCRIPTION "[RFC-EDITOR: Remove this and all following REVISION statements prior to publication as an RFC] Changes from draft-ietf-frnetmib-mfrmib-00.txt o changed experimental number to IANA-approved 105. o changed interface type for frf16MfrBundle to IANA-approved 163. " REVISION "9912061700Z" DESCRIPTION "Updates: o changed name to draft-ietf-frnetmib-mfrmib-00 o updated text to match last MIB revisions o corrected description of bundleIfIndexMappingTable o added objects to show configured and current bundle links. " REVISION "9910212020Z" DESCRIPTION "Updated after comments from Michael Allen and Ken Rehben. o corrected options for sequence number length o changed frf16Mfr prefix to mfr o created a sub-group for scalars o created an entry in the bundleTable for maximum links per bundle o changed indices to not-accessible o changed DisplayString to SnmpAdminString o updated some of the object descriptions o added a -EXP to the name of the MIB o added some DEFVAL and REFERENCE clauses" REVISION "9910151300Z" DESCRIPTION "Updated after review at the October meeting in Huntsville: o removed log table o removed several columns from each table o combined configuration, status and error tables into one table each for bundles and bundle links o added new objects for - maximum number of bundles - maximum fragment size - size of sequence number o added notifications o added conformance information" REVISION "9910011440Z" DESCRIPTION "Initial version submitted to the Frame Relay Forum October meeting in Huntsville as FRFTC/99-151." ::= { experimental 105 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Textual Conventions -- --------------------------------------------------------- -- --------------------------------------------------------- BundleLinkState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The possible states for a bundle link, as defined in Annex A of FRF.16." REFERENCE "FRF.16 Annex A" SYNTAX INTEGER { bundleLinkStateAddSent (1), bundleLinkStateAddRx (2), bundleLinkStateAddAckRx (3), bundleLinkStateUp (4), bundleLinkStateIdlePending (5), bundleLinkStateIdle (6), bundleLinkStateDown (7), bundleLinkStateDownIdle (8) } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Object Identifers -- --------------------------------------------------------- -- --------------------------------------------------------- mfrMibObjects OBJECT IDENTIFIER ::= { mfrMib 1 } mfrMibTraps OBJECT IDENTIFIER ::= { mfrMib 2 } mfrMibConformance OBJECT IDENTIFIER ::= { mfrMib 3 } mfrMibScalarObjects OBJECT IDENTIFIER ::= { mfrMibObjects 1 } mfrMibBundleObjects OBJECT IDENTIFIER ::= { mfrMibObjects 2 } mfrMibBundleLinkObjects OBJECT IDENTIFIER ::= { mfrMibObjects 3 } mfrMibTrapsPrefix OBJECT IDENTIFIER ::= { mfrMibTraps 0 } mfrMibGroups OBJECT IDENTIFIER ::= { mfrMibConformance 1 } mfrMibCompliances OBJECT IDENTIFIER ::= { mfrMibConformance 2 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Scalars -- --------------------------------------------------------- -- --------------------------------------------------------- bundleMaxNumBundles OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to inform the manager of the maximum number of bundles supported by this device." ::= { mfrMibScalarObjects 1 } bundleNextIndex OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to assist the manager in selecting a value for bundleIndex during row creation in the bundleTable. It can also be used to avoid race conditions with multiple managers trying to create rows in the table (see RFC 2494 [RFC2494] for one such alogrithm)." REFERENCE "RFC 2494" ::= { mfrMibScalarObjects 2 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Bundle Table -- --------------------------------------------------------- -- --------------------------------------------------------- bundleTable OBJECT-TYPE SYNTAX SEQUENCE OF BundleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The bundle configuration and status table. There is a one-to-one correspondence between a bundle and an interface represented in the ifTable. The following objects of the ifTable have specific meaning for a MFR bundle: ifAdminStatus - the bundle admin status ifOperStatus - the bundle operational status ifSpeed - the current bandwidth of the bundle ifInUcastPkts - the number of frames received on the bundle ifOutUcastPkts - the number of frames transmitted on the bundle ifInErrors - frame (not fragment) errors ifOutErrors - frame (not fragment) errors " ::= { mfrMibBundleObjects 3 } bundleEntry OBJECT-TYPE SYNTAX BundleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the bundle table." INDEX { bundleIndex } ::= { bundleTable 1 } BundleEntry ::= SEQUENCE { bundleIndex Integer32, bundleIfIndex InterfaceIndex, bundleRowStatus RowStatus, bundleNearEndName SnmpAdminString, bundleFragmentation INTEGER, bundleMaxFragSize Integer32, bundleTimerHello INTEGER, bundleTimerAck INTEGER, bundleCountMaxRetry INTEGER, bundleActivationClass INTEGER, bundleThreshold Integer32, bundleMaxDiffDelay Integer32, bundleSeqNumSize INTEGER, bundleMaxBundleLinks Integer32, bundleLinksConfigured Integer32, bundleLinksActive Integer32, bundleBandwidth Integer32, bundleFarEndName SnmpAdminString, bundleResequencingErrors Counter32 } bundleIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index into the table. While this corresponds to an entry in the ifTable, the value of bundleIndex need not match that of the ifIndex in the ifTable. A manager can use bundleNextIndex to select a unique bundleIndex for creating a new row." ::= { bundleEntry 1 } bundleIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value should match an entry in the interface table. The ifType should be set to frf16MfrBundle(163). For example: if the value of bundleIfIndex is 10, then a corresponding entry should be present in the ifTable with an index of 10." ::= { bundleEntry 2 } bundleRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The bundleRowStatus object allows create, change, and delete operations on bundle entries." REFERENCE "RFC 1903" ::= { bundleEntry 3 } bundleNearEndName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The configured name of the bundle." REFERENCE "FRF.16 section 3.4.1" ::= { bundleEntry 4 } bundleFragmentation OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether the bundle performs/accepts fragmentation and re-assembly. The possible values are: enable(1) - Bundle links will fragment frames disable(2) - Bundle links will not fragment frames." DEFVAL { disable } ::= { bundleEntry 5 } bundleMaxFragSize OBJECT-TYPE SYNTAX Integer32 (-1..8184) UNITS "Octets" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum fragment size supported. Note that this is only valid if bundleFragmentation is set to enable(1). Zero is not a valid fragment size. A bundle that does not support fragmentation must be set to -1." DEFVAL { -1 } ::= { bundleEntry 6 } bundleTimerHello OBJECT-TYPE SYNTAX INTEGER (1..180) UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The configured MFR Hello Timer value." REFERENCE "FRF.16 section 4.3.8.1" DEFVAL { 10 } ::= { bundleEntry 7 } bundleTimerAck OBJECT-TYPE SYNTAX INTEGER (1..10) UNITS "Seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The configured MFR T_ACK value." REFERENCE "FRF.16 section 4.3.8.2" DEFVAL { 4 } ::= { bundleEntry 8 } bundleCountMaxRetry OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-create STATUS current DESCRIPTION "The MFR N_MAX_RETRY value." REFERENCE "FRF.16 section 4.3.8.3" DEFVAL { 2 } ::= { bundleEntry 9 } bundleActivationClass OBJECT-TYPE SYNTAX INTEGER { bundleActivationClassA (1), -- at least one must link up bundleActivationClassB (2), -- all links must be up bundleActivationClassC (3), -- a certain number must be up bundleActivationClassD (4) -- custom } MAX-ACCESS read-create STATUS current DESCRIPTION "Controls the conditions under which the bundle is activated. The following settings are available: bundleActivationClassA(1) - at least one must link up bundleActivationClassB(2) - all links must be up bundleActivationClassC(3) - a certain number must be up. Refer to bundleThreshold for the required number. bundleActivationClassD(4) - custom (implementation specific)." REFERENCE "FRF.16 section 4.2.2.1" DEFVAL { bundleActivationClassA } ::= { bundleEntry 10 } bundleThreshold OBJECT-TYPE SYNTAX Integer32 UNITS "Bundle Links" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the number of links that must be in operational 'up' state before the bundle will transition to an operational up/active state. If the number of operational 'up' links falls below this value, then the bundle will transition to an inactive state. Note - this is only valid when bundleActivationClass is set to bundleActivationClassC or, depending upon the implementation, to bundleActivationClassD." REFERENCE "FRF.16 section 4.2.2.1" DEFVAL { -1 } ::= { bundleEntry 11 } bundleMaxDiffDelay OBJECT-TYPE SYNTAX Integer32 UNITS "Milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum delay difference between the bundle links." DEFVAL { -1 } ::= { bundleEntry 12 } bundleSeqNumSize OBJECT-TYPE SYNTAX INTEGER { seqNumSize12bit (1), seqNumSize24bit (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether the standard FRF.12 12-bit sequence number is used or the optional 24-bit sequence number." REFERENCE "FRFTC/99-194" DEFVAL { seqNumSize12bit } ::= { bundleEntry 13 } bundleMaxBundleLinks OBJECT-TYPE SYNTAX Integer32 UNITS "Bundle Links" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bundle links supported for this bundle." ::= { bundleEntry 14 } bundleLinksConfigured OBJECT-TYPE SYNTAX Integer32 UNITS "Bundle Links" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of links configured for the bundle." ::= { bundleEntry 15 } bundleLinksActive OBJECT-TYPE SYNTAX Integer32 UNITS "Bundle Links" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of links that are active." ::= { bundleEntry 16 } bundleBandwidth OBJECT-TYPE SYNTAX Integer32 UNITS "Bits/Sec" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of available bandwidth on the bundle" ::= { bundleEntry 17 } bundleFarEndName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the bundle received from the far end." REFERENCE "FRF.16 section 3.4.1" ::= { bundleEntry 18 } bundleResequencingErrors OBJECT-TYPE SYNTAX Counter32 UNITS "Error Events" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of resequncing errors. Each event may correspond to multiple lost frames. Example: Say sequence number 56, 59 and 60 is received for DLCI 100. It is decided by some means that sequence 57 and 58 is lost. This counter should then be incremented by ONE, even though two frames were lost." ::= { bundleEntry 19 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- ifIndex Mapping to Bundle Index Table -- --------------------------------------------------------- -- --------------------------------------------------------- bundleIfIndexMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF BundleIfIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table mapping the values of ifIndex to the bundleIndex. This is required in order to find the bundleIndex given an ifIndex. The mapping of bundleIndex to ifIndex is provided by the bundleIfIndex entry in the bundleTable." ::= { mfrMibBundleObjects 4 } bundleIfIndexMappingEntry OBJECT-TYPE SYNTAX BundleIfIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row describes one ifIndex to bundleIndex mapping." INDEX { ifIndex } ::= { bundleIfIndexMappingTable 1 } BundleIfIndexMappingEntry ::= SEQUENCE { bundleIfIndexMappingIndex InterfaceIndex } bundleIfIndexMappingIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The bundleIndex of the given ifIndex." ::= { bundleIfIndexMappingEntry 2 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Bundle Link Table -- --------------------------------------------------------- -- --------------------------------------------------------- bundleLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF BundleLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The bundle link configuration and status table. There is a one-to-one correspondence between a bundle link and a physical interface represented in the ifTable. The ifIndex of the physical interface is used to index the bundle link table, and to create rows. The following objects of the ifTable have specific meaning for a MFR bundle link: ifAdminStatus - the bundle link admin status ifOperStatus - the bundle link operational status ifSpeed - the bandwidth of the bundle link interface ifInUcastPkts - the number of frames received on the bundle link ifOutUcastPkts - the number of frames transmitted on the bundle link ifInErrors - frame and fragment errors ifOutErrors - frame and fragment errors" ::= { mfrMibBundleLinkObjects 1 } bundleLinkEntry OBJECT-TYPE SYNTAX BundleLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the bundle link table." INDEX { ifIndex } ::= { bundleLinkTable 1 } BundleLinkEntry ::= SEQUENCE { bundleLinkRowStatus RowStatus, bundleLinkConfigBundleIndex Integer32, bundleLinkNearEndName SnmpAdminString, bundleLinkState BundleLinkState, bundleLinkFarEndName SnmpAdminString, bundleLinkFarEndBundleName SnmpAdminString, bundleLinkDelay Integer32, bundleLinkFramesControlTx Counter32, bundleLinkFramesControlRx Counter32, bundleLinkFramesControlInvalid Counter32, bundleLinkTimerExpiredCount Counter32, bundleLinkLoopbackSuspected Counter32, bundleLinkUnexpectedSequence Counter32, bundleLinkMismatch Counter32 } bundleLinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The bundleLinkRowStatus object allows create, change, and delete operations on bundleLink entries. The create operation must fail if no physical interface is associated with the bundle link." ::= { bundleLinkEntry 1 } bundleLinkConfigBundleIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The bundleLinkConfigBundleIndex object allows the manager to control the bundle to which the bundle link is assigned. If no value were in this field, then the bundle would remain in NOT_READY rowStatus and be unable to go to active. With an appropriate bundleIndex in this field, then we could put the bundleLink row in NOT_IN_SERVICE or ACTIVE rowStatus." ::= { bundleLinkEntry 2 } bundleLinkNearEndName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The configured bundle link name that is sent to the far end." ::= { bundleLinkEntry 3 } bundleLinkState OBJECT-TYPE SYNTAX BundleLinkState MAX-ACCESS read-only STATUS current DESCRIPTION "Current bundle link state as defined by the MFR protocol described in Annex A of FRF.16." REFERENCE "FRF.16 Annex A" ::= { bundleLinkEntry 4 } bundleLinkFarEndName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of bundle link received from far end." REFERENCE "FRF.16 section 3.4.2" ::= { bundleLinkEntry 5 } bundleLinkFarEndBundleName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of far end bundle for this link received from far end." REFERENCE "FRF.16 section 3.4.1" ::= { bundleLinkEntry 6 } bundleLinkDelay OBJECT-TYPE SYNTAX Integer32 UNITS "Milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Current round-trip delay for this bundle link. The value -1 is returned when an implementation does not support measurement of the bundle link delay." REFERENCE "FRF.16 section 3.4.4" ::= { bundleLinkEntry 7 } bundleLinkFramesControlTx OBJECT-TYPE SYNTAX Counter32 UNITS "Frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of MFR control frames sent." REFERENCE "FRF.16 section 3.2" ::= { bundleLinkEntry 8 } bundleLinkFramesControlRx OBJECT-TYPE SYNTAX Counter32 UNITS "Frames" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of valid MFR control frames received." REFERENCE "FRF.16 section 3.2" ::= { bundleLinkEntry 9 } bundleLinkFramesControlInvalid OBJECT-TYPE SYNTAX Counter32 UNITS "Frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of invalid MFR control frames received." REFERENCE "FRF.16 section 3.2" ::= { bundleLinkEntry 10 } bundleLinkTimerExpiredCount OBJECT-TYPE SYNTAX Counter32 UNITS "Timer Expiration Events" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the T_HELLO or T_ACK timers expired." REFERENCE "FRF.16 section 4.3.8.1 and 4.3.8.2" ::= { bundleLinkEntry 11 } bundleLinkLoopbackSuspected OBJECT-TYPE SYNTAX Counter32 UNITS "Loopback Suspected Events" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a loopback has been suspected (based upon the use of magic numbers)." REFERENCE "FRF.16 section 4.3.7" ::= { bundleLinkEntry 12 } bundleLinkUnexpectedSequence OBJECT-TYPE SYNTAX Counter32 UNITS "Frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of data MFR frames discarded because the sequence number of the frame for a DLCI was less than (delayed frame) or equal to (duplicate frame) the one expected for that DLCI. Example: Say frames with sequence numbers 56, 58, 59 is received for DLCI 100. While waiting for sequence number 57 another frame with sequence number 58 arrives. Frame 58 is discarded and the counter is incremented." REFERENCE "FRF.16 section 4.2.3.2" ::= { bundleLinkEntry 13 } bundleLinkMismatch OBJECT-TYPE SYNTAX Counter32 UNITS "Bundle Name Mismatch Events" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the unit has been notified by the remote peer that the bundle name is inconsistent with other bundle links attached to the far-end bundle." REFERENCE "FRF.16 section 4.3.2.4" ::= { bundleLinkEntry 14 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Notifications/Traps -- --------------------------------------------------------- -- --------------------------------------------------------- mfrMibTrapBundleLinkMismatch NOTIFICATION-TYPE OBJECTS { bundleNearEndName, bundleFarEndName, bundleLinkNearEndName, bundleLinkFarEndName, bundleLinkFarEndBundleName } STATUS current DESCRIPTION "This trap indicates that a bundle link mismatch has been detected. The following objects are reported: bundleNearEndName: configured name of near end bundle bundleFarEndName: previously reported name of far end bundle bundleLinkNearEndName: configured name of near end bundle bundleLinkFarEndName: reported name of far end bundle bundleLinkFarEndBundleName: currently reported name of far end bundle Note: that the configured items may have been configured automatically. Note: The bundleLinkMismatch counter is incremented when the trap is sent." REFERENCE "FRF.16 section 4.3.2.4" ::= { mfrMibTrapsPrefix 1 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Conformance/Compliance -- --------------------------------------------------------- -- --------------------------------------------------------- mfrMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for equipment that implements the FRF16 MIB. All of the current groups are mandatory, but a number of objects may be read-only if the implementation does not allow configuration." MODULE -- this module MANDATORY-GROUPS { mfrMibBundleGroup, mfrMibBundleLinkGroup, mfrMibTrapGroup } OBJECT bundleFragmentation MIN-ACCESS read-only DESCRIPTION "Write access is not required, but the value used must be reported." OBJECT bundleMaxFragSize MIN-ACCESS read-only DESCRIPTION "Write access is not required, but the value used must be reported. A value of -1 indicates that the value is not applicable." OBJECT bundleThreshold MIN-ACCESS read-only DESCRIPTION "Write access is not required, but the value used must be reported. A value of -1 indicates that the value is not applicable." OBJECT bundleMaxDiffDelay MIN-ACCESS read-only DESCRIPTION "Write access is not required, but the value used must be reported." OBJECT bundleSeqNumSize MIN-ACCESS read-only DESCRIPTION "Write access is not required, but the value used must be reported. A value of -1 indicates that the value is not applicable." ::= { mfrMibCompliances 1 } -- --------------------------------------------------------- -- --------------------------------------------------------- -- Units of Conformance -- --------------------------------------------------------- -- --------------------------------------------------------- mfrMibBundleGroup OBJECT-GROUP OBJECTS { bundleMaxNumBundles, bundleNextIndex, bundleIfIndex, bundleRowStatus, bundleNearEndName, bundleFragmentation, bundleMaxFragSize, bundleTimerHello, bundleTimerAck, bundleCountMaxRetry, bundleActivationClass, bundleThreshold, bundleMaxDiffDelay, bundleMaxBundleLinks, bundleLinksConfigured, bundleLinksActive, bundleBandwidth, bundleSeqNumSize, bundleFarEndName, bundleResequencingErrors, bundleIfIndexMappingIndex } STATUS current DESCRIPTION "Group of objects describing bundles." ::= { mfrMibGroups 1 } mfrMibBundleLinkGroup OBJECT-GROUP OBJECTS { bundleLinkRowStatus, bundleLinkConfigBundleIndex, bundleLinkNearEndName, bundleLinkState, bundleLinkFarEndName, bundleLinkFarEndBundleName, bundleLinkDelay, bundleLinkFramesControlTx, bundleLinkFramesControlRx, bundleLinkFramesControlInvalid, bundleLinkTimerExpiredCount, bundleLinkLoopbackSuspected, bundleLinkUnexpectedSequence, bundleLinkMismatch } STATUS current DESCRIPTION "Group of objects describing bundle links." ::= { mfrMibGroups 2 } mfrMibTrapGroup NOTIFICATION-GROUP NOTIFICATIONS { mfrMibTrapBundleLinkMismatch } STATUS current DESCRIPTION "Group of objects describing notifications (traps)." ::= { mfrMibGroups 3 } END