-- extracted from draft-ietf-mboned-ip-mcast-mib-03.txt -- at Thu Aug 3 06:06:44 2006 IPMCAST-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, mib-2, Unsigned32, Counter32, Counter64, Gauge32, TimeTicks FROM SNMPv2-SMI RowStatus, TEXTUAL-CONVENTION, TruthValue, StorageType, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB InterfaceIndexOrZero, InterfaceIndex FROM IF-MIB IANAipRouteProtocol, IANAipMRouteProtocol FROM IANA-RTPROTO-MIB InetAddress, InetAddressType, InetAddressPrefixLength, InetZoneIndex FROM INET-ADDRESS-MIB; ipMcastMIB MODULE-IDENTITY LAST-UPDATED "200608020000Z" -- 2 August 2006 ORGANIZATION "IETF MBONED Working Group" CONTACT-INFO "David McWalter Data Connection Limited 100 Church Street Enfield, EN2 6BQ UK Phone: +44 208 366 1177 EMail: dmcw@dataconnection.com Dave Thaler Microsoft Corporation One Microsoft Way Redmond, WA 98052-6399 US Phone: +1 425 703 8835 EMail: dthaler@dthaler.microsoft.com Andrew Kessler Cisco Systems 425 E. Tasman Drive San Jose, CA 95134 US Phone: +1 408 526 5139 EMail: kessler@cisco.com" DESCRIPTION "The MIB module for management of IP Multicast function. This MIB module contains information about IP Multicast routing, data forwarding, and data reception. This MIB module is independent of the multicast protocol(s) and address type(s) that are in use. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices." -- RFC Ed.: replace yyyy with actual RFC number & remove this note REVISION "200608020000Z" -- 2 August 2006 DESCRIPTION "Changes from RFC 2932: 1) This MIB module is independent of address type, whereas RFC 2932 only supported IPv4. 2) This MIB module allows several multicast protocols to perform routing on a single interface, whereas RFC 2932 assumed each interface supported at most one multicast routing protocol. This MIB module retains but deprecates the object ipMcastInterfaceProtocol. 3) This MIB module includes objects that are not specific to multicast routing. It allows management of multicast function on systems that do not perform routing, whereas RFC 2932 was restricted to multicast routing. 4) This MIB module includes a table of Source-Specific Multicast (SSM) address ranges to which RFC 3569 SSM semantics should be applied. 5) This MIB module includes a table of local applications that are receiving multicast data. 6) This MIB module includes a table of multicast scope zones. Published as RFC yyyy." -- RFC Ed.: replace yyyy with actual RFC number & remove this note ::= { mib-2 XXX } -- RFC Ed.: replace XXX with IANA-assigned number & remove this note -- -- Textual conventions -- LanguageTag ::= TEXTUAL-CONVENTION DISPLAY-HINT "99a" STATUS current DESCRIPTION "A language tag with all alphabetic characters converted to lowercase. This restriction is intended to make the lexical ordering imposed by SNMP useful when applied to language tags. Note that it is theoretically possible for a valid language tag to exceed the allowed length of this syntax, and thus be impossible to represent with this syntax. Sampling of language tags in current use on the Internet suggests that this limit does not pose a serious problem in practice." REFERENCE "RFC 3283" SYNTAX OCTET STRING (SIZE (1..99)) -- -- Top-level structure of the MIB -- ipMcastMIBObjects OBJECT IDENTIFIER ::= { ipMcastMIB 1 } ipMcast OBJECT IDENTIFIER ::= { ipMcastMIBObjects 1 } ipMcastEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The enabled status of IP Multicast function on this system." ::= { ipMcast 1 } ipMcastRouteEntryCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rows in the ipMcastRouteTable. This can be used to check for multicast routing activity, and to monitor the multicast routing table size." ::= { ipMcast 7 } -- -- The Multicast Interface Table -- ipMcastInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table used to manage the multicast protocol active on an interface." ::= { ipMcast 4 } ipMcastInterfaceEntry OBJECT-TYPE SYNTAX IpMcastInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing the multicast protocol information for a particular interface." INDEX { ipMcastInterfaceIfIndex } ::= { ipMcastInterfaceTable 1 } IpMcastInterfaceEntry ::= SEQUENCE { ipMcastInterfaceIfIndex InterfaceIndex, ipMcastInterfaceTtl Unsigned32, ipMcastInterfaceProtocol IANAipMRouteProtocol, ipMcastInterfaceRateLimit Unsigned32, ipMcastInterfaceInMcastOctets Counter32, ipMcastInterfaceOutMcastOctets Counter32, ipMcastInterfaceInMcastPkts Counter32, ipMcastInterfaceOutMcastPkts Counter32, ipMcastInterfaceHCInMcastOctets Counter64, ipMcastInterfaceHCOutMcastOctets Counter64, ipMcastInterfaceHCInMcastPkts Counter64, ipMcastInterfaceHCOutMcastPkts Counter64 } ipMcastInterfaceIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the interface for which this entry contains information." ::= { ipMcastInterfaceEntry 1 } ipMcastInterfaceTtl OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The datagram TTL threshold for the interface. Any IP multicast datagrams with a TTL (IPv4) or Hop Limit (IPv6) less than this threshold will not be forwarded out the interface. The default value of 0 means all multicast packets are forwarded out the interface." DEFVAL { 0 } ::= { ipMcastInterfaceEntry 2 } ipMcastInterfaceProtocol OBJECT-TYPE SYNTAX IANAipMRouteProtocol MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The multicast protocol running on this interface. More than one multicast protocol can be used on an interface, so this object is ambiguous. Use of this object is deprecated." ::= { ipMcastInterfaceEntry 3 } ipMcastInterfaceRateLimit OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The rate-limit, in kilobits per second, of forwarded multicast traffic on the interface. A rate-limit of 0 indicates that no rate limiting is done." DEFVAL { 0 } ::= { ipMcastInterfaceEntry 4 } ipMcastInterfaceInMcastOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have arrived on the interface, including framing characters. This object is similar to ifInOctets in the Interfaces MIB, except that only multicast packets are counted." ::= { ipMcastInterfaceEntry 5 } ipMcastInterfaceOutMcastOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have been sent on the interface." ::= { ipMcastInterfaceEntry 6 } ipMcastInterfaceInMcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have arrived on the interface. In many cases, this object is identical to ifInMulticastPkts in the Interfaces MIB. However, some implementations use ifXTable for Layer 2 traffic statistics and ipMcastInterfaceTable at Layer 3. In this case a difference between these objects probably indicates that some Layer 3 multicast packets are being transmitted as unicast at Layer 2." REFERENCE "RFC 2863 ifInMulticastPkts" ::= { ipMcastInterfaceEntry 7 } ipMcastInterfaceOutMcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have been sent on the interface. In many cases, this object is identical to ifOutMulticastPkts in the Interfaces MIB. However, some implementations use ifXTable for Layer 2 traffic statistics and ipMcastInterfaceTable at Layer 3. In this case a difference between these objects probably indicates that some Layer 3 multicast packets are being transmitted as unicast at Layer 2." REFERENCE "RFC 2863 ifOutMulticastPkts" ::= { ipMcastInterfaceEntry 8 } ipMcastInterfaceHCInMcastOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have arrived on the interface, including framing characters. This object is a 64-bit version of ipMcastRouteInterfaceInMcastOctets. It is similar to ifHCInOctets in the Interfaces MIB, except that only multicast packets are counted." ::= { ipMcastInterfaceEntry 9 } ipMcastInterfaceHCOutMcastOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have been sent on the interface. This object is a 64-bit version of ipMcastRouteInterfaceOutMcastOctets." ::= { ipMcastInterfaceEntry 10 } ipMcastInterfaceHCInMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have arrived on the interface. In many cases, this object is identical to ifHCInMulticastPkts in the Interfaces MIB. However, some implementations use ifXTable for Layer 2 traffic statistics and ipMcastInterfaceTable at Layer 3. In this case a difference between these objects probably indicates that some Layer 3 multicast packets are being transmitted as unicast at Layer 2." REFERENCE "RFC 2863 ifHCInMulticastPkts" ::= { ipMcastInterfaceEntry 11 } ipMcastInterfaceHCOutMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have been sent on the interface. In many cases, this object is identical to ifHCOutMulticastPkts in the Interfaces MIB. However, some implementations use ifXTable for Layer 2 traffic statistics and ipMcastInterfaceTable at Layer 3. In this case a difference between these objects probably indicates that some Layer 3 multicast packets are being transmitted as unicast at Layer 2." REFERENCE "RFC 2863 ifHCOutMulticastPkts" ::= { ipMcastInterfaceEntry 12 } -- -- The SSM Range Table -- ipMcastSsmRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastSsmRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to create and manage the range(s) of group addresses to which SSM semantics should be applied." REFERENCE "RFC 3569" ::= { ipMcast 8 } ipMcastSsmRangeEntry OBJECT-TYPE SYNTAX IpMcastSsmRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing a range of group addresses to which SSM semantics should be applied." REFERENCE "RFC 3569" INDEX { ipMcastSsmRangeAddressType, ipMcastSsmRangeAddress, ipMcastSsmRangePrefixLength } ::= { ipMcastSsmRangeTable 1 } IpMcastSsmRangeEntry ::= SEQUENCE { ipMcastSsmRangeAddressType InetAddressType, ipMcastSsmRangeAddress InetAddress, ipMcastSsmRangePrefixLength InetAddressPrefixLength, ipMcastSsmRangeRowStatus RowStatus, ipMcastSsmRangeStorageType StorageType } ipMcastSsmRangeAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address type of the multicast group prefix." ::= { ipMcastSsmRangeEntry 1 } ipMcastSsmRangeAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address which, when combined with ipMcastSsmRangePrefixLength, gives the group prefix for this SSM range. The InetAddressType is given by ipMcastSsmRangeAddressType. This address object is only significant up to ipMcastSsmRangePrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry. For IPv6 SSM address ranges, only ranges prefixed by FF3x::/16 are permitted, where 'x' is a valid IPv6 RFC 4291 multicast address scope. The syntax of the address range is given by RFC 3306 sections 4 and 7. For addresses of type ipv4z or ipv6z, the appended zone index is significant even though it lies beyond the prefix length. The use of these address types indicate that this SSM range entry applies only within the given zone. Zone index zero is not valid in this table. If non-global scope SSM range entries are present, then consistent ipMcastBoundaryTable entries are required on routers at the zone boundary." REFERENCE "RFC 2365, RFC 4291 section 2.7, RFC 3306 sections 4, 6 and 7" ::= { ipMcastSsmRangeEntry 2 } ipMcastSsmRangePrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with ipMcastSsmRangeAddress, gives the group prefix for this SSM range. The InetAddressType is given by ipMcastSsmRangeAddressType. For values 'ipv4' and 'ipv4z', this object must be in the range 4..32. For values 'ipv6' and 'ipv6z', this object must be in the range 8..128." REFERENCE "RFC 2365, RFC 4291 section 2.7, RFC 3306 sections 4, 6 and 7" ::= { ipMcastSsmRangeEntry 3 } ipMcastSsmRangeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which rows in this table can be created and destroyed. This status object can be set to active(1) without setting any other columnar objects in this entry. All writeable objects in this entry can be modified when the status of this entry is active(1)." ::= { ipMcastSsmRangeEntry 4 } ipMcastSsmRangeStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this row. Rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { ipMcastSsmRangeEntry 5 } -- -- The IP Multicast Routing Table -- ipMcastRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing multicast routing information for IP datagrams sent by particular sources to to the IP multicast groups known to this router." ::= { ipMcast 2 } ipMcastRouteEntry OBJECT-TYPE SYNTAX IpMcastRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing the multicast routing information for IP datagrams from a particular source and addressed to a particular IP multicast group address." INDEX { ipMcastRouteGroupAddressType, ipMcastRouteGroup, ipMcastRouteGroupPrefixLength, ipMcastRouteSourceAddressType, ipMcastRouteSource, ipMcastRouteSourcePrefixLength } ::= { ipMcastRouteTable 1 } IpMcastRouteEntry ::= SEQUENCE { ipMcastRouteGroupAddressType InetAddressType, ipMcastRouteGroup InetAddress, ipMcastRouteGroupPrefixLength InetAddressPrefixLength, ipMcastRouteSourceAddressType InetAddressType, ipMcastRouteSource InetAddress, ipMcastRouteSourcePrefixLength InetAddressPrefixLength, ipMcastRouteUpstreamNeighborType InetAddressType, ipMcastRouteUpstreamNeighbor InetAddress, ipMcastRouteInIfIndex InterfaceIndexOrZero, ipMcastRouteTimeStamp TimeStamp, ipMcastRouteExpiryTime TimeTicks, ipMcastRoutePkts Counter32, ipMcastRouteDifferentInIfPackets Counter32, ipMcastRouteOctets Counter32, ipMcastRouteProtocol IANAipMRouteProtocol, ipMcastRouteRtProtocol IANAipRouteProtocol, ipMcastRouteRtAddressType InetAddressType, ipMcastRouteRtAddress InetAddress, ipMcastRouteRtPrefixLength InetAddressPrefixLength, ipMcastRouteRtType INTEGER, ipMcastRouteHCOctets Counter64, ipMcastRouteDifferentInIfOctets Counter32, ipMcastRouteTtlDropPackets Counter32, ipMcastRouteTtlDropOctets Counter32 } ipMcastRouteGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteGroup. Legal values correspond to the subset of address families for which multicast forwarding is supported." ::= { ipMcastRouteEntry 1 } ipMcastRouteGroup OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with the corresponding value specified in ipMcastRouteGroupPrefixLength, identifies the groups for which this entry contains multicast routing information. This address object is only significant up to ipMcastRouteGroupPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." ::= { ipMcastRouteEntry 2 } ipMcastRouteGroupPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with the corresponding value of ipMcastRouteGroup, identifies the groups for which this entry contains multicast routing information." ::= { ipMcastRouteEntry 3 } ipMcastRouteSourceAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteSource. The value MUST be the same as the value of ipMcastRouteGroupType." ::= { ipMcastRouteEntry 4 } ipMcastRouteSource OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address which, when combined with the corresponding value of ipMcastRouteSourcePrefixLength, identifies the sources for which this entry contains multicast routing information. This address object is only significant up to ipMcastRouteGroupPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." ::= { ipMcastRouteEntry 5 } ipMcastRouteSourcePrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with the corresponding value of ipMcastRouteSource, identifies the sources for which this entry contains multicast routing information." ::= { ipMcastRouteEntry 6 } ipMcastRouteUpstreamNeighborType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteUpstreamNeighbor. The value MUST be the same as the value of ipMcastRouteGroupType." ::= { ipMcastRouteEntry 7 } ipMcastRouteUpstreamNeighbor OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the upstream neighbor (for example, RPF neighbor) from which IP datagrams from these sources to this multicast address are received. If the upstream neighbor is unknown, then ipMcastRouteUpstreamNeighbor will be 0.0.0.0 in the case of an IPv4 entry, and 0:0:0:0:0:0:0:0 in the case of an IPv6 entry (for example, in BIDIR-PIM)." ::= { ipMcastRouteEntry 8 } ipMcastRouteInIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The value of ifIndex for the interface on which IP datagrams sent by these sources to this multicast address are received. A value of 0 indicates that datagrams are not subject to an incoming interface check, but may be accepted on multiple interfaces (for example, in BIDIR-PIM)." ::= { ipMcastRouteEntry 9 } ipMcastRouteTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at which the multicast routing information represented by this entry was learned by the router." ::= { ipMcastRouteEntry 10 } ipMcastRouteExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum amount of time remaining before this entry will be aged out. The value 0 indicates that the entry is not subject to aging. If ipMcastRouteNextHopState is pruned(1), this object represents the remaining time until the prune expires. If this timer expires, state reverts to forwarding(2). Otherwise, this object represents the time until this entry is removed from the table." ::= { ipMcastRouteEntry 11 } ipMcastRoutePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets routed using this multicast route entry. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 12 } ipMcastRouteDifferentInIfPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets which this router has received from these sources and addressed to this multicast group address, which were dropped because they were received on an unexpected interface. For RPF checking protocols (such as PIM-SM), these packets arrived on interfaces other than ipMcastRouteInIfIndex, and were dropped because of this failed RPF check. (RPF paths are 'Reverse Path Forwarding' path; the unicast routes to the expected origin of multicast data flows). Other protocols may drop packets on an incoming interface check for different reasons (for example, BIDIR-PIM performs a DF check on receipt of packets). All packets dropped as a result of an incoming interface check are counted here. If this counter increases rapidly, this indicates a problem. A significant quantity of multicast data is arriving at this router on unexpected interfaces, and is not being forwarded. For guidance, if the rate of increase of this counter exceeds 1% of the rate of increase of ipMcastRoutePkts, then there are multicast routing problems that require investigation. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 13 } ipMcastRouteOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in IP datagrams which were received from these sources and addressed to this multicast group address, and which were forwarded by this router. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 14 } ipMcastRouteProtocol OBJECT-TYPE SYNTAX IANAipMRouteProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast routing protocol via which this multicast forwarding entry was learned." ::= { ipMcastRouteEntry 15 } ipMcastRouteRtProtocol OBJECT-TYPE SYNTAX IANAipRouteProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "The routing mechanism via which the route used to find the upstream or parent interface for this multicast forwarding entry was learned. Inclusion of values for routing protocols is not intended to imply that those protocols need be supported." ::= { ipMcastRouteEntry 16 } ipMcastRouteRtAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteRtAddress. The value MUST be the same as the value of ipMcastRouteGroupType." ::= { ipMcastRouteEntry 17 } ipMcastRouteRtAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address portion of the route used to find the upstream or parent interface for this multicast forwarding entry. This address object is only significant up to ipMcastRouteGroupPrefixLength bits. The remainder of the address bits are zero." ::= { ipMcastRouteEntry 18 } ipMcastRouteRtPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The length in bits of the mask associated with the route used to find the upstream or parent interface for this multicast forwarding entry." ::= { ipMcastRouteEntry 19 } ipMcastRouteRtType OBJECT-TYPE SYNTAX INTEGER { unicast (1), -- Unicast route used in multicast RIB multicast (2) -- Multicast route } MAX-ACCESS read-only STATUS current DESCRIPTION "The reason the given route was placed in the (logical) multicast Routing Information Base (RIB). A value of unicast means that the route would normally be placed only in the unicast RIB, but was placed in the multicast RIB (instead or in addition) due to local configuration, such as when running PIM over RIP. A value of multicast means that the route was explicitly added to the multicast RIB by the routing protocol, such as DVMRP or Multiprotocol BGP." ::= { ipMcastRouteEntry 20 } ipMcastRouteHCOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in IP datagrams which were received from these sources and addressed to this multicast group address, and which were forwarded by this router. This object is a 64-bit version of ipMcastRouteOctets. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 21 } ipMcastRouteDifferentInIfOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in IP datagrams which this router has received from these sources and addressed to this multicast group address, which were dropped because they were received on an unexpected interface. For RPF checking protocols (such as PIM-SM), these packets arrived on interfaces other than ipMcastRouteInIfIndex, and were dropped because of this failed RPF check. (RPF paths are 'Reverse Path Forwarding' path; the unicast routes to the expected origin of multicast data flows). Other protocols may drop packets on an incoming interface check for different reasons (for example, BIDIR-PIM performs a DF check on receipt of packets). All packets dropped as a result of an incoming interface check are counted here. If this counter increases rapidly, this indicates a problem. A significant quantity of multicast data is arriving at this router on unexpected interfaces, and is not being forwarded. For guidance, if the rate of increase of this counter exceeds 1% of the rate of increase of ipMcastRouteOctets, then there are multicast routing problems that require investigation. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 22 } ipMcastRouteTtlDropPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets which this router has received from these sources and addressed to this multicast group address, which were dropped because the TTL (IPv4) or Hop Limit (IPv6) was decremented to zero, or to a value less than ipMcastInterfaceTtl for all next hops. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 23 } ipMcastRouteTtlDropOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in IP datagrams which this router has received from these sources and addressed to this multicast group address, which were dropped because the TTL (IPv4) or Hop Limit (IPv6) was decremented to zero, or to a value less than ipMcastInterfaceTtl for all next hops. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteTimeStamp." ::= { ipMcastRouteEntry 24 } -- -- The IP Multicast Routing Next Hop Table -- ipMcastRouteNextHopTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing information on the next-hops on outgoing interfaces for routing IP multicast datagrams. Each entry is one of a list of next-hops on outgoing interfaces for particular sources sending to a particular multicast group address." ::= { ipMcast 3 } ipMcastRouteNextHopEntry OBJECT-TYPE SYNTAX IpMcastRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the list of next-hops on outgoing interfaces to which IP multicast datagrams from particular sources to an IP multicast group address are routed." INDEX { ipMcastRouteNextHopGroupAddressType, ipMcastRouteNextHopGroup, ipMcastRouteNextHopSourceAddressType, ipMcastRouteNextHopSource, ipMcastRouteNextHopSourcePrefixLength, ipMcastRouteNextHopIfIndex, ipMcastRouteNextHopAddressType, ipMcastRouteNextHopAddress } ::= { ipMcastRouteNextHopTable 1 } IpMcastRouteNextHopEntry ::= SEQUENCE { ipMcastRouteNextHopGroupAddressType InetAddressType, ipMcastRouteNextHopGroup InetAddress, ipMcastRouteNextHopSourceAddressType InetAddressType, ipMcastRouteNextHopSource InetAddress, ipMcastRouteNextHopSourcePrefixLength InetAddressPrefixLength, ipMcastRouteNextHopIfIndex InterfaceIndex, ipMcastRouteNextHopAddressType InetAddressType, ipMcastRouteNextHopAddress InetAddress, ipMcastRouteNextHopState INTEGER, ipMcastRouteNextHopTimeStamp TimeStamp, ipMcastRouteNextHopExpiryTime TimeTicks, ipMcastRouteNextHopClosestMemberHops Unsigned32, ipMcastRouteNextHopProtocol IANAipMRouteProtocol, ipMcastRouteNextHopPkts Counter32, ipMcastRouteNextHopOctets Counter32 } ipMcastRouteNextHopGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteNextHopGroup. Legal values correspond to the subset of address families for which multicast forwarding is supported." ::= { ipMcastRouteNextHopEntry 1 } ipMcastRouteNextHopGroup OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group for which this entry specifies a next-hop on an outgoing interface." ::= { ipMcastRouteNextHopEntry 2 } ipMcastRouteNextHopSourceAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteNextHopSource. The value MUST be the same as the value of ipMcastRouteNextHopGroupType." ::= { ipMcastRouteNextHopEntry 3 } ipMcastRouteNextHopSource OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address which, when combined with the corresponding value of the mask specified in ipMcastRouteNextHopSourcePrefixLength, identifies the sources for which this entry specifies a next-hop on an outgoing interface. This address object is only significant up to ipMcastRouteNextHopSourcePrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." ::= { ipMcastRouteNextHopEntry 4 } ipMcastRouteNextHopSourcePrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with the corresponding value specified in ipMcastRouteNextHopSource, identifies the sources for which this entry specifies a next-hop on an outgoing interface." ::= { ipMcastRouteNextHopEntry 5 } ipMcastRouteNextHopIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of the interface for the outgoing interface for this next-hop." ::= { ipMcastRouteNextHopEntry 6 } ipMcastRouteNextHopAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastRouteNextHopAddress. The value MUST be the same as the value of ipMcastRouteNextHopGroupType." ::= { ipMcastRouteNextHopEntry 7 } ipMcastRouteNextHopAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of the next-hop specific to this entry. For most interfaces, this is identical to ipMcastRouteNextHopGroup. NBMA interfaces, however, may have multiple next-hop addresses out a single outgoing interface." ::= { ipMcastRouteNextHopEntry 8 } ipMcastRouteNextHopState OBJECT-TYPE SYNTAX INTEGER { pruned(1), forwarding(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of whether the outgoing interface and next- hop represented by this entry is currently being used to forward IP datagrams. The value 'forwarding' indicates it is currently being used; the value 'pruned' indicates it is not." ::= { ipMcastRouteNextHopEntry 9 } ipMcastRouteNextHopTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at which the multicast routing information represented by this entry was learned by the router." ::= { ipMcastRouteNextHopEntry 10 } ipMcastRouteNextHopExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum amount of time remaining before this entry will be aged out. If ipMcastRouteNextHopState is pruned(1), the remaining time until the prune expires and the state reverts to forwarding(2). Otherwise, the remaining time until this entry is removed from the table. The time remaining may be copied from ipMcastRouteExpiryTime if the protocol in use for this entry does not specify next-hop timers. The value 0 indicates that the entry is not subject to aging." ::= { ipMcastRouteNextHopEntry 11 } ipMcastRouteNextHopClosestMemberHops OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum number of hops between this router and any member of this IP multicast group reached via this next-hop on this outgoing interface. Any IP multicast datagrams for the group which have a TTL (IPv4) or Hop Count (IPv6) less than this number of hops will not be forwarded to this next-hop. This is an optimization applied by multicast routing protocols that explicitly track hop counts to downstream listeners. Multicast protocols that are not aware of hop counts to downstream listeners set this object to zero." ::= { ipMcastRouteNextHopEntry 12 } ipMcastRouteNextHopProtocol OBJECT-TYPE SYNTAX IANAipMRouteProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "The routing mechanism via which this next-hop was learned." ::= { ipMcastRouteNextHopEntry 13 } ipMcastRouteNextHopPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets which have been forwarded using this route. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteNextHopTimeStamp." ::= { ipMcastRouteNextHopEntry 14 } ipMcastRouteNextHopOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have been forwarded using this route. Discontinuities in this monotonically increasing value occur at re-initialization of the management system. Discontinuities can also occur as a result of routes being removed and replaced, which can be detected by observing the value of ipMcastRouteNextHopTimeStamp." ::= { ipMcastRouteNextHopEntry 15 } -- -- The IP Multicast Scope Boundary Table -- ipMcastBoundaryTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastBoundaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the system's multicast scope zone boundaries." REFERENCE "RFC 4007 section 5" ::= { ipMcast 5 } ipMcastBoundaryEntry OBJECT-TYPE SYNTAX IpMcastBoundaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) describing one of this device's multicast scope zone boundaries." REFERENCE "RFC 2365 section 5, RFC 4007 section 5" INDEX { ipMcastBoundaryIfIndex, ipMcastBoundaryAddressType, ipMcastBoundaryAddress, ipMcastBoundaryAddressPrefixLength } ::= { ipMcastBoundaryTable 1 } IpMcastBoundaryEntry ::= SEQUENCE { ipMcastBoundaryIfIndex InterfaceIndex, ipMcastBoundaryAddressType InetAddressType, ipMcastBoundaryAddress InetAddress, ipMcastBoundaryAddressPrefixLength InetAddressPrefixLength, ipMcastBoundaryStatus RowStatus, ipMcastBoundaryStorageType StorageType, ipMcastBoundaryDroppedMcastOctets Counter32, ipMcastBoundaryDroppedMcastPkts Counter32, ipMcastBoundaryHCDroppedMcastOctets Counter64, ipMcastBoundaryHCDroppedMcastPkts Counter64 } ipMcastBoundaryIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IfIndex value for the interface to which this boundary applies. Packets with a destination address in the associated address/mask range will not be forwarded over this interface. For IPv4, zone boundaries cut through links. Therefore this is an external interface. This may be either a physical or virtual interface (tunnel, encapsulation, and so forth.) For IPv6, zone boundaries cut through nodes. Therefore this is a virtual interface within the node. This is not an external interface, either real or virtual. Packets crossing this interface neither arrive at nor leave the node, but only move between zones within the node." REFERENCE "RFC 2365 section 5, RFC 4007 section 5" ::= { ipMcastBoundaryEntry 1 } ipMcastBoundaryAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastBoundaryAddress. Legal values correspond to the subset of address families for which multicast forwarding is supported." ::= { ipMcastBoundaryEntry 2 } ipMcastBoundaryAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address which, when combined with the corresponding value of ipMcastBoundaryAddressPrefixLength, identifies the group range for which the scoped boundary exists. Scoped IPv4 multicast address ranges must be prefixed by 239.0.0.0/4. Scoped IPv6 multicast address ranges are FF0x::/16, where x is a valid RFC 4291 multicast scope. An IPv6 address prefixed by FF1x::/16 is a non-permanently- assigned address. An IPv6 address prefixed by FF3x::/16 is a unicast-prefix-based multicast addresses. A zone boundary for FF0x::/16 implies an identical boundary for these other prefixes. No separate FF1x::/16 or FF3x::/16 entries exist in this table. This address object is only significant up to ipMcastBoundaryAddressPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." REFERENCE "RFC 2365, RFC 3306 section 4, RFC 4291 section 2.7" ::= { ipMcastBoundaryEntry 3 } ipMcastBoundaryAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which when, combined with the corresponding value of ipMcastBoundaryAddress, identifies the group range for which the scoped boundary exists. The InetAddressType is given by ipMcastBoundaryAddressType. For 'ipv4' this object must be in the range 4..32. For 'ipv6', this object must be 16." ::= { ipMcastBoundaryEntry 4 } ipMcastBoundaryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which rows in this table can be created and destroyed. This status object can be set to active(1) without setting any other columnar objects in this entry. All writeable objects in this entry can be modified when the status of this entry is active(1)." ::= { ipMcastBoundaryEntry 5 } ipMcastBoundaryStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this row. Rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { ipMcastBoundaryEntry 6 } ipMcastBoundaryDroppedMcastOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have been dropped as a result of this zone boundary configuration." ::= { ipMcastBoundaryEntry 7 } ipMcastBoundaryDroppedMcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have been dropped as a result of this zone boundary configuration." ::= { ipMcastBoundaryEntry 8 } ipMcastBoundaryHCDroppedMcastOctets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of multicast packets that have been dropped as a result of this zone boundary configuration. This object is a 64-bit version of ipMcastBoundaryDroppedMcastOctets." ::= { ipMcastBoundaryEntry 9 } ipMcastBoundaryHCDroppedMcastPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multicast packets that have been dropped as a result of this zone boundary configuration. This object is a 64-bit version of ipMcastBoundaryDroppedMcastPkts." ::= { ipMcastBoundaryEntry 10 } -- -- The IP Multicast Scope Name Table -- ipMcastScopeNameTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastScopeNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing multicast scope names." REFERENCE "RFC 4007 section 4" ::= { ipMcast 6 } ipMcastScopeNameEntry OBJECT-TYPE SYNTAX IpMcastScopeNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) that names a multicast address scope." REFERENCE "RFC 4007 section 4" INDEX { ipMcastScopeNameAddressType, ipMcastScopeNameAddress, ipMcastScopeNameAddressPrefixLength, IMPLIED ipMcastScopeNameLanguage } ::= { ipMcastScopeNameTable 1 } IpMcastScopeNameEntry ::= SEQUENCE { ipMcastScopeNameAddressType InetAddressType, ipMcastScopeNameAddress InetAddress, ipMcastScopeNameAddressPrefixLength InetAddressPrefixLength, ipMcastScopeNameLanguage LanguageTag, ipMcastScopeNameString SnmpAdminString, ipMcastScopeNameDefault TruthValue, ipMcastScopeNameStatus RowStatus, ipMcastScopeNameStorageType StorageType } ipMcastScopeNameAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastScopeNameAddress. Legal values correspond to the subset of address families for which multicast forwarding is supported." ::= { ipMcastScopeNameEntry 1 } ipMcastScopeNameAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address which, when combined with the corresponding value of ipMcastScopeNameAddressPrefixLength, identifies the group range associated with the multicast scope. Scoped IPv4 multicast address ranges must be prefixed by 239.0.0.0/4. Scoped IPv6 multicast address ranges are FF0x::/16, where x is a valid RFC 4291 multicast scope. An IPv6 address prefixed by FF1x::/16 is a non-permanently- assigned address. An IPv6 address prefixed by FF3x::/16 is a unicast-prefix-based multicast addresses. A scope FF0x::/16 implies an identical scope name for these other prefixes. No separate FF1x::/16 or FF3x::/16 entries exist in this table. This address object is only significant up to ipMcastScopeNameAddressPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." REFERENCE "RFC 2365, RFC 3306 section 4, RFC 4291 section 2.7" ::= { ipMcastScopeNameEntry 2 } ipMcastScopeNameAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with the corresponding value of ipMcastScopeNameAddress, identifies the group range associated with the multicast scope. The InetAddressType is given by ipMcastScopeNameAddressType. For 'ipv4' this object must be in the range 4..32. For 'ipv6', this object must be 16." ::= { ipMcastScopeNameEntry 3 } ipMcastScopeNameLanguage OBJECT-TYPE SYNTAX LanguageTag MAX-ACCESS not-accessible STATUS current DESCRIPTION "Language tag associated with the scope name." REFERENCE "RFC 3283" ::= { ipMcastScopeNameEntry 4 } ipMcastScopeNameString OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The textual name associated with the multicast scope. The value of this object should be suitable for displaying to end-users, such as when allocating a multicast address in this scope. When no name is specified, the default value of this object for IPv4 should is the string 239.x.x.x/y with x and y replaced with decimal values to describe the address and mask length associated with the scope. When no name is specified, the default value of this object for IPv6 should is the string FF0x::/16, with x replaced by the hexadecimal value for the RFC 4291 multicast scope. An IPv6 address prefixed by FF1x::/16 is a non-permanently- assigned address. An IPv6 address prefixed by FF3x::/16 is a unicast-prefix-based multicast addresses. A scope FF0x::/16 implies an identical scope name for these other prefixes. No separate FF1x::/16 or FF3x::/16 entries exist in this table." REFERENCE "RFC 2365, RFC 3306 section 4, RFC 4291 section 2.7" ::= { ipMcastScopeNameEntry 5 } ipMcastScopeNameDefault OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, indicates a preference that the name in the following language should be used by applications if no name is available in a desired language." DEFVAL { false } ::= { ipMcastScopeNameEntry 6 } ipMcastScopeNameStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row, by which rows in this table can be created and destroyed. Before the row can be activated, the object ipMcastScopeNameString must be set to a valid value. All writeable objects in this entry can be modified when the status is active(1)." ::= { ipMcastScopeNameEntry 7 } ipMcastScopeNameStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this row. Rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { ipMcastScopeNameEntry 8 } -- -- The Multicast Listeners Table -- ipMcastLocalListenerTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastLocalListenerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing local applications or services that have joined multicast groups as listeners. Entries exist for all addresses in the multicast range for all applications and services as they are classified on this device." ::= { ipMcast 9 } ipMcastLocalListenerEntry OBJECT-TYPE SYNTAX IpMcastLocalListenerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) identifying a local application or service that has joined a multicast group as a listener." INDEX { ipMcastLocalListenerGroupAddressType, ipMcastLocalListenerGroupAddress, ipMcastLocalListenerSourceAddressType, ipMcastLocalListenerSourceAddress, ipMcastLocalListenerSourcePrefixLength, ipMcastLocalListenerRunIndex } ::= { ipMcastLocalListenerTable 1 } IpMcastLocalListenerEntry ::= SEQUENCE { ipMcastLocalListenerGroupAddressType InetAddressType, ipMcastLocalListenerGroupAddress InetAddress, ipMcastLocalListenerSourceAddressType InetAddressType, ipMcastLocalListenerSourceAddress InetAddress, ipMcastLocalListenerSourcePrefixLength InetAddressPrefixLength, ipMcastLocalListenerRunIndex Unsigned32 } ipMcastLocalListenerGroupAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastLocalListenerGroupAddress. Legal values correspond to the subset of address families for which multicast is supported." ::= { ipMcastLocalListenerEntry 1 } ipMcastLocalListenerGroupAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group for which this entry specifies locally joined applications or services." ::= { ipMcastLocalListenerEntry 2 } ipMcastLocalListenerSourceAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value indicating the address family of the address contained in ipMcastLocalListenerSource. The value MUST be the same as the value of ipMcastLocalListenerAddressType." ::= { ipMcastLocalListenerEntry 3 } ipMcastLocalListenerSourceAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (0|4|8|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network address which, when combined with the corresponding value of the mask specified in ipMcastLocalListenerSourcePrefixLength, identifies the sources for which this entry specifies a local listener. This address object is only significant up to ipMcastLocalListenerSourcePrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry." ::= { ipMcastLocalListenerEntry 4 } ipMcastLocalListenerSourcePrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The length in bits of the mask which, when combined with the corresponding value specified in ipMcastLocalListenerSource, identifies the sources for which this entry specifies a local listener. A mask length of zero corresponds to all sources within the group." ::= { ipMcastLocalListenerEntry 5 } ipMcastLocalListenerRunIndex OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value corresponding to a piece of software running on this router or host system. Where possible, this should be the system's native, unique identification number. This identifier is platform-specific. It may correspond to a process ID or application instance number. A value of zero indicates that the application instance(s) cannot be identified. A value of zero indicates that one or more unidentified applications have joined the specified multicast groups (for the specified sources) as listeners." REFERENCE "RFC 2287 sysApplRunIndex" ::= { ipMcastLocalListenerEntry 6 } -- -- The Multicast Zone Table -- ipMcastZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF IpMcastZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing scope zones on this device." REFERENCE "RFC 4007 section 5" ::= { ipMcast 10 } ipMcastZoneEntry OBJECT-TYPE SYNTAX IpMcastZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) describing a scope zone on this device." REFERENCE "RFC 4007 section 5" INDEX { ipMcastZoneIndex } ::= { ipMcastZoneTable 1 } IpMcastZoneEntry ::= SEQUENCE { ipMcastZoneIndex InetZoneIndex, ipMcastZoneScopeDefaultZoneIndex InetZoneIndex, ipMcastZoneScopeAddressType InetAddressType, ipMcastZoneScopeAddress InetAddress, ipMcastZoneScopeAddressPrefixLength InetAddressPrefixLength } ipMcastZoneIndex OBJECT-TYPE SYNTAX InetZoneIndex (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This zone index uniquely identifies a zone on a device. Each zone is for a given scope. Scope-level information in this table is for the unique scope that corresponds to this zone. Zero is a special value used to request the default zone for a given scope. Zero is not a valid value for this object. To test whether ipMcastZoneIndex is the default zone for this scope, test whether ipMcastZoneIndex is equal to ipMcastZoneScopeDefaultZoneIndex." ::= { ipMcastZoneEntry 1 } ipMcastZoneScopeDefaultZoneIndex OBJECT-TYPE SYNTAX InetZoneIndex (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The default zone index for this scope. This is the zone that this device will use if the default (zero) zone is requested for this scope. Zero is not a valid value for this object." ::= { ipMcastZoneEntry 2 } ipMcastZoneScopeAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address type for which this scope zone exists." ::= { ipMcastZoneEntry 3 } ipMcastZoneScopeAddress OBJECT-TYPE SYNTAX InetAddress (SIZE (4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast group address which, when combined with ipMcastZoneScopeAddressPrefixLength, gives the multicast address range for this scope. The InetAddressType is given by ipMcastZoneScopeAddressType. Scoped IPv4 multicast address ranges are prefixed by 239.0.0.0/4. Scoped IPv6 multicast address ranges are FF0x::/16, where x is a valid RFC 4291 multicast scope. An IPv6 address prefixed by FF1x::/16 is a non-permanently- assigned address. An IPv6 address prefixed by FF3x::/16 is a unicast-prefix-based multicast addresses. A scope FF0x::/16 implies an identical scope for these other prefixes. No separate FF1x::/16 or FF3x::/16 entries exist in this table. This address object is only significant up to ipMcastZoneScopeAddressPrefixLength bits. The remainder of the address bits are zero." REFERENCE "RFC 2365, RFC 3306 section 4, RFC 4291 section 2.7" ::= { ipMcastZoneEntry 4 } ipMcastZoneScopeAddressPrefixLength OBJECT-TYPE SYNTAX InetAddressPrefixLength (4..32) MAX-ACCESS read-only STATUS current DESCRIPTION "The length in bits of the mask which, when combined with ipMcastZoneScopeAddress, gives the multicast address prefix for this scope. The InetAddressType is given by ipMcastZoneAddressType. For 'ipv4' this object must be in the range 4..32. For 'ipv6', this object must be 16." ::= { ipMcastZoneEntry 5 } -- -- Conformance information -- ipMcastMIBConformance OBJECT IDENTIFIER ::= { ipMcastMIB 2 } ipMcastMIBCompliances OBJECT IDENTIFIER ::= { ipMcastMIBConformance 1 } ipMcastMIBGroups OBJECT IDENTIFIER ::= { ipMcastMIBConformance 2 } -- -- Compliance statements -- ipMcastMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Implementations of all the mandatory MIB groups listed below can claim full compliance. This MIB contains several InetAddressType and InetAddress objects, but not all IP address types are supported by all protocol implementations. A MIB implementation can claim full compliance if all IP address types supported by the protocol implementation are supported by the MIB implementation." MODULE -- this module MANDATORY-GROUPS { ipMcastMIBBasicGroup } OBJECT ipMcastEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP ipMcastMIBRouteGroup DESCRIPTION "This group is mandatory if the system is a router." OBJECT ipMcastInterfaceTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipMcastInterfaceRateLimit MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP ipMcastMIBHopCountGroup DESCRIPTION "This group is optional." GROUP ipMcastMIBPktsOutGroup DESCRIPTION "This group is optional." GROUP ipMcastMIBHCInterfaceGroup DESCRIPTION "This group is mandatory only for those network interfaces for which the value of the corresponding instance of ifSpeed is greater than 20,000,000 bits/second." GROUP ipMcastMIBRouteProtoGroup DESCRIPTION "This group is mandatory if the system is a router." GROUP ipMcastMIBSsmGroup DESCRIPTION "This group is optional." GROUP ipMcastMIBLocalListenerGroup DESCRIPTION "This group is optional." GROUP ipMcastMIBBoundaryIfGroup DESCRIPTION "This group is mandatory if the system is a router that supports administratively-scoped multicast address boundaries." OBJECT ipMcastBoundaryStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP ipMcastMIBScopeNameGroup DESCRIPTION "This group is mandatory if the system is a router that supports multicast scope names." OBJECT ipMcastScopeNameString MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipMcastScopeNameDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipMcastScopeNameStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP ipMcastMIBIfPktsGroup DESCRIPTION "This group is optional." GROUP ipMcastMIBRouteOctetsGroup DESCRIPTION "This group is optional." ::= { ipMcastMIBCompliances 1 } ipMcastMIBMRouteCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "Implementations of this compliance statement are equivalent to compliance with the deprecated IPMROUTE-MIB module." MODULE -- this module MANDATORY-GROUPS { ipMcastMIBMRouteBasicGroup } ::= { ipMcastMIBCompliances 2 } -- -- Units of conformance -- ipMcastMIBMRouteBasicGroup OBJECT-GROUP OBJECTS { ipMcastEnable, ipMcastRouteEntryCount, ipMcastRouteUpstreamNeighborType, ipMcastRouteUpstreamNeighbor, ipMcastRouteInIfIndex, ipMcastRouteTimeStamp, ipMcastRouteExpiryTime, ipMcastRouteNextHopState, ipMcastRouteNextHopTimeStamp, ipMcastRouteNextHopExpiryTime, ipMcastRouteNextHopProtocol, ipMcastRouteNextHopPkts, ipMcastInterfaceTtl, ipMcastInterfaceProtocol, ipMcastInterfaceRateLimit, ipMcastInterfaceInMcastOctets, ipMcastInterfaceOutMcastOctets } STATUS deprecated DESCRIPTION "A collection of objects to support basic management of IP Multicast routing. This conformance group is deprecated. It is replaced by ipMcastMIBBasicGroup and ipMcastMIBRouteGroup" ::= { ipMcastMIBGroups 1 } ipMcastMIBHopCountGroup OBJECT-GROUP OBJECTS { ipMcastRouteNextHopClosestMemberHops } STATUS current DESCRIPTION "A collection of objects to support management of the use of hop counts in IP Multicast routing." ::= { ipMcastMIBGroups 2 } ipMcastMIBPktsOutGroup OBJECT-GROUP OBJECTS { ipMcastRouteNextHopPkts } STATUS current DESCRIPTION "A collection of objects to support management of packet counters for each outgoing interface entry of a route." ::= { ipMcastMIBGroups 3 } ipMcastMIBHCInterfaceGroup OBJECT-GROUP OBJECTS { ipMcastInterfaceHCInMcastOctets, ipMcastInterfaceHCOutMcastOctets, ipMcastInterfaceHCInMcastPkts, ipMcastInterfaceHCOutMcastPkts, ipMcastRouteHCOctets, ipMcastBoundaryHCDroppedMcastOctets, ipMcastBoundaryHCDroppedMcastPkts } STATUS current DESCRIPTION "A collection of objects providing information specific to high speed (greater than 20,000,000 bits/second) network interfaces." ::= { ipMcastMIBGroups 4 } ipMcastMIBRouteProtoGroup OBJECT-GROUP OBJECTS { ipMcastRouteProtocol, ipMcastRouteRtProtocol, ipMcastRouteRtAddressType, ipMcastRouteRtAddress, ipMcastRouteRtPrefixLength, ipMcastRouteRtType } STATUS current DESCRIPTION "A collection of objects providing information on the relationship between multicast routing information and the IP Forwarding Table." ::= { ipMcastMIBGroups 5 } ipMcastMIBBasicGroup OBJECT-GROUP OBJECTS { ipMcastEnable, ipMcastRouteEntryCount } STATUS current DESCRIPTION "A collection of objects to support basic management of IP Multicast protocols." ::= { ipMcastMIBGroups 6 } ipMcastMIBRouteGroup OBJECT-GROUP OBJECTS { ipMcastRouteUpstreamNeighborType, ipMcastRouteUpstreamNeighbor, ipMcastRouteInIfIndex, ipMcastRouteTimeStamp, ipMcastRouteExpiryTime, ipMcastRoutePkts, ipMcastRouteDifferentInIfPackets, ipMcastRouteOctets, ipMcastRouteNextHopState, ipMcastRouteNextHopTimeStamp, ipMcastRouteNextHopExpiryTime, ipMcastRouteNextHopProtocol, ipMcastRouteNextHopPkts, ipMcastInterfaceTtl, ipMcastInterfaceRateLimit, ipMcastInterfaceInMcastOctets, ipMcastInterfaceOutMcastOctets, ipMcastRouteTtlDropPackets, ipMcastRouteTtlDropOctets } STATUS current DESCRIPTION "A collection of objects to support basic management of IP Multicast routing." ::= { ipMcastMIBGroups 7 } ipMcastMIBSsmGroup OBJECT-GROUP OBJECTS { ipMcastSsmRangeRowStatus, ipMcastSsmRangeStorageType } STATUS current DESCRIPTION "A collection of objects to support management of the use of Source-Specific Multicast routing." ::= { ipMcastMIBGroups 8 } ipMcastMIBLocalListenerGroup OBJECT-GROUP OBJECTS { ipMcastLocalListenerRunIndex } STATUS current DESCRIPTION "A collection of objects to support management of local listeners on hosts or routers." ::= { ipMcastMIBGroups 9 } ipMcastMIBBoundaryIfGroup OBJECT-GROUP OBJECTS { ipMcastBoundaryStatus, ipMcastBoundaryStorageType, ipMcastBoundaryDroppedMcastOctets, ipMcastBoundaryDroppedMcastPkts, ipMcastZoneScopeDefaultZoneIndex, ipMcastZoneScopeAddressType, ipMcastZoneScopeAddress, ipMcastZoneScopeAddressPrefixLength } STATUS current DESCRIPTION "A collection of objects to support management of scoped multicast address boundaries." ::= { ipMcastMIBGroups 10 } ipMcastMIBScopeNameGroup OBJECT-GROUP OBJECTS { ipMcastScopeNameString, ipMcastScopeNameDefault, ipMcastScopeNameStatus, ipMcastScopeNameStorageType } STATUS current DESCRIPTION "A collection of objects to support management of multicast address scope names." ::= { ipMcastMIBGroups 11 } ipMcastMIBIfPktsGroup OBJECT-GROUP OBJECTS { ipMcastInterfaceInMcastPkts, ipMcastInterfaceOutMcastPkts } STATUS current DESCRIPTION "A collection of objects to support management of packet counters for each interface entry." ::= { ipMcastMIBGroups 12 } ipMcastMIBRouteOctetsGroup OBJECT-GROUP OBJECTS { ipMcastRouteOctets, ipMcastRouteNextHopOctets, ipMcastRouteDifferentInIfOctets } STATUS current DESCRIPTION "A collection of objects to support management of octet counters for each forwarding entry." ::= { ipMcastMIBGroups 13 } END -- -- Copyright (C) The Internet Society (2006). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- -- Acknowledgment -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society.