-- extracted from draft-ietf-isis-wg-mib-06.txt -- at Thu Nov 22 06:07:18 2001 ISIS-MIB DEFINITIONS ::= BEGIN IMPORTS TEXTUAL-CONVENTION, DisplayString, RowStatus, TruthValue, TestAndIncr FROM SNMPv2-TC MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, Integer32, Counter32, experimental FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; isisMIB MODULE-IDENTITY LAST-UPDATED "200111151200Z" -- UTC date of the most recent REVISION. ORGANIZATION "IETF IS-IS for IP Internets Working Group" CONTACT-INFO "Jeff Parker Axiowave Networks 200 Nickerson Rd. Marlborough, MA 01752 jparker@axiowave.com" DESCRIPTION "" ::= { experimental 37 } -- Top-level stucture of the MIB isisObjects OBJECT IDENTIFIER ::= { isisMIB 1 } isisNotifications OBJECT IDENTIFIER ::= { isisMIB 2 } isisConformance OBJECT IDENTIFIER ::= { isisMIB 3 } -- OBJECT IDENTIFIER definitions isisSystem OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 1 } isisCirc OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 2 } isisCircLevelValues OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 3 } isisCircPDUCounters OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 4 } isisISAdj OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 5 } isisReachAddr OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 6 } isisIPReachAddr OBJECT-IDENTITY STATUS current DESCRIPTION "" ::= { isisObjects 7 } -- Type definitions OSINSAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "OSI Network Service Address, e.g. NSAP, Network Entity Title" SYNTAX OCTET STRING (SIZE(1..20)) SNPAAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A MAC Address or DTE Address or other SNPA Address." SYNTAX OCTET STRING (SIZE(0..20)) NSAPPrefix ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "NSAP Prefix. The first octet of the string is used to encode as an unsigned integer the length in bits of the subsequent prefix. This length must be a multiple of 4 bits and may range from 0..160. The second and subsequent octets are used to hold the prefix value. If the last 4 bits of the last octet are not part of the prefix then their value is undefined." SYNTAX OCTET STRING (SIZE(1..21)) SNPAPrefix ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "SNPA Prefix. The first octet of the string is used to encode as an unsigned integer the length in bits of the subsequent prefix. The second and subsequent octets are used to hold the prefix value. Bits in the last octet which are not part of the prefix have undefined value." SYNTAX OCTET STRING (SIZE(1..21)) SystemID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A system ID." SYNTAX OCTET STRING (SIZE(0..6)) AdminState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type used in enabling and disabling a row." SYNTAX INTEGER { off(1), on(2) } UpTime ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Number of seconds since the object has entered the state 'up'. If the object is not up, the number of seconds since the circuit was up, or since the system started, if the circuit has never been up." SYNTAX Integer32 LSPBuffSize ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Integer sub range for LSP size." SYNTAX Integer32 (512..1492) LevelState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "states of the ISIS protocol." SYNTAX INTEGER { off (1), on (2), waiting (3) } SupportedProtocol ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Types of network protocol supported by Integrated ISIS. The values for ISO8473 and IP are those registered for these protocols in ISO TR9577." SYNTAX INTEGER { iso8473(129), ip(204), ipV6(205) } DefaultMetric ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Integer sub-range for default metric for single hop." SYNTAX Integer32 (1..63) MetricType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Class of metric: Internal or External." SYNTAX INTEGER { internal(1), external(2) } CircuitID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "ID for a circuit." SYNTAX OCTET STRING (SIZE(2..9)) ISPriority ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Integer sub-range for ISIS priority." SYNTAX Integer32 (1..127) InetAddressType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A value that represents a type of Internet address. unknown(0) An unknown address type. ipv4(1) An IPv4 address ipv6(2) An IPv6 address dns(16) A DNS domain name. See RFC 2851 for more details." SYNTAX INTEGER { unknown(0), ipv4(1), -- these named numbers are aligned ipv6(2), -- with AddressFamilyNumbers from dns(16) -- IANA-ADDRESS-FAMILY-NUMBERS-MIB } InetAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Denotes a generic Internet address. An InetAddress value is always interpreted within the context of an InetAddressType value registered immediately before the InetAddress object." SYNTAX OCTET STRING (SIZE (0..255)) InetAddressPrefixLength ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Denotes the length of a generic Internet network address prefix. A value of n corresponds to an IP address mask which has n contiguous 1-bits from the most significant bit (MSB) and all other bits set to 0." SYNTAX Integer32 -- Behaviour Definitions -- ResettingTimer behaviour definition -- "This object specifies the interval between certain events in -- the operation of the protocol state machine. If the value of -- this object is set to a new value while the protocol state -- machine is in operation, the implementation shall take the -- necessary steps to ensure that for any time interval which -- was in progress when the value of the corresponding object -- was changed, the next expiration of that interval takes place -- the specified time after the original start of that interval, -- or immediately, whichever is later. The precision with which -- this time shall be implemented shall be the same as that -- associated with the basic operation of the timer object." -- ReplaceOnlyWhileDisabled behaviour definition -- "This object may not be modified while the corresponding -- table row's variable of type AdminState is in state on." -- OperationalState behaviour definition -- "This object controls the enabling and disabling of the -- corresponding table row. Setting this object to the value -- off has the effect of disabling the corresponding row. -- Setting this object to the value on has the effect of -- enabling the corresponding row. Setting the value of this -- object to the same value as its current value has no effect. -- If the table entry also contains an object controlling the -- row status then the object following the operationalState -- behaviour shall not be set to on when the object following -- the Row Status behaviour has value off. An attempt to do -- so is rejected." isisSysTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisSysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The set of instances of the Integrated IS-IS protocol existing on the system." ::= { isisSystem 1 } isisSysEntry OBJECT-TYPE SYNTAX IsisSysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row defines information specific to a single instance of the protocol existing on the system." REFERENCE "{ISIS.poi cLNSISISBasic-P (1)}" INDEX { isisSysInstance } ::= { isisSysTable 1 } IsisSysEntry ::= SEQUENCE { isisSysInstance Integer32, isisSysVersion DisplayString, isisSysType INTEGER, isisSysID SystemID, isisSysMaxPathSplits Integer32, isisSysMaxLSPGenInt Integer32, isisSysOrigL1LSPBuffSize LSPBuffSize, isisSysMaxAreaAddresses Integer32, isisSysMinL1LSPGenInt Integer32, isisSysMinL2LSPGenInt Integer32, isisSysPollESHelloRate Integer32, isisSysWaitTime Integer32, isisSysAdminState AdminState, isisSysL1State LevelState, isisSysCorrLSPs Counter32, isisSysLSPL1DbaseOloads Counter32, isisSysManAddrDropFromAreas Counter32, isisSysAttmptToExMaxSeqNums Counter32, isisSysSeqNumSkips Counter32, isisSysOwnLSPPurges Counter32, isisSysIDFieldLenMismatches Counter32, isisSysMaxAreaAddrMismatches Counter32, isisSysOrigL2LSPBuffSize LSPBuffSize, isisSysL2State LevelState, isisSysLSPL2DbaseOloads Counter32, isisSysAuthFails Counter32, isisSysLSPIgnoreErrors TruthValue, isisSysLogAdjacencyChanges TruthValue, isisSysPartChanges Counter32, isisSysMaxAreaCheck TruthValue, isisSysNextCircIndex TestAndIncr, isisSysExistState RowStatus, isisSysL2toL1Leaking TruthValue, isisSysSetOverload INTEGER } isisSysInstance OBJECT-TYPE SYNTAX Integer32 (1..10000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The unique identifier of the Integrated IS-IS instance to which this row corresponds. This object follows the index behaviour." ::= { isisSysEntry 1 } isisSysVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The version number of the IS-IS protocol to which this instance conforms. This value must be set by the implementation when the row is valid." REFERENCE "{ISIS.aoi version (1)}" ::= { isisSysEntry 2 } isisSysType OBJECT-TYPE SYNTAX INTEGER { level1IS (1), level2IS (2), level1L2IS (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of this instance of the Integrated IS-IS protocol. This object follows the replaceOnlyWhileDisabled behaviour." REFERENCE "{ISIS.aoi iSType (2)}" ::= { isisSysEntry 3 } isisSysID OBJECT-TYPE SYNTAX SystemID MAX-ACCESS read-create STATUS current DESCRIPTION "The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the instance's area addresses to form the Network Entity Titles valid for this instance. The derivation of a value for this object is implementation-specific. Some implementations may assign values and not permit write, others may require the value to be set manually." REFERENCE "{ISIS.aoi systemId (119)}" ::= { isisSysEntry 4 } isisSysMaxPathSplits OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum number of paths with equal routing metric value which it is permitted to split between. This object follows the replaceOnlyWhileDisabled behaviour." REFERENCE "{ISIS.aoi maximumPathSplits (3)}" DEFVAL { 2 } ::= { isisSysEntry 5 } isisSysMaxLSPGenInt OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum interval, in seconds, between generated LSPs by this instance. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi maximumLSPGenerationInterval (6)}" DEFVAL { 900 } ::= { isisSysEntry 6 } isisSysOrigL1LSPBuffSize OBJECT-TYPE SYNTAX LSPBuffSize MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum size of Level 1 LSPs and SNPs originated by this instance. This object follows the replaceOnlyWhileDisabled behaviour." REFERENCE "{ISIS.aoi originatingL1LSPBufferSize (9)}" DEFVAL { 1492 } ::= { isisSysEntry 7 } isisSysMaxAreaAddresses OBJECT-TYPE SYNTAX Integer32 (3..254) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of area addresses to be permitted for the area in which this instance exists. Note that all Intermediate Systems in the same area must have the same value configured for this attribute if correct operation is to be assumed. This object follows the replaceOnlyWhileDisabled behaviour." REFERENCE "{ISIS.aoi maximumAreaAddresses (4)}" DEFVAL { 3 } ::= { isisSysEntry 8 } isisSysMinL1LSPGenInt OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum interval, in seconds, between successive generation of L1 LSPs with the same LSPID by this instance. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi minimumLSPGenerationInterval (11)}" DEFVAL { 30 } ::= { isisSysEntry 9 } isisSysMinL2LSPGenInt OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum interval, in seconds, between successive generation of L2 LSPs with the same LSPID by this instance. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi minimumLSPGenerationInterval (11)}" DEFVAL { 30 } ::= { isisSysEntry 10 } isisSysPollESHelloRate OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The value, in seconds, to be used for the suggested ES configuration timer in ISH PDUs when soliciting the ES configuration." REFERENCE "{ISIS.aoi pollESHelloRate (13)}" DEFVAL { 50 } ::= { isisSysEntry 11 } isisSysWaitTime OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Number of seconds to delay in waiting state before entering on state. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi waitingTime (15)}" DEFVAL { 60 } ::= { isisSysEntry 12 } isisSysAdminState OBJECT-TYPE SYNTAX AdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative state of this instance of the Integrated IS-IS protocol. Setting this object to the value on when its current value is off enables operation of this instance of the Integrated IS-IS protocol." DEFVAL { off } ::= { isisSysEntry 13 } isisSysL1State OBJECT-TYPE SYNTAX LevelState MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Level 1 database." REFERENCE "{ISIS.aoi l1State (17)}" ::= { isisSysEntry 14 } isisSysCorrLSPs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of corrupted LSPs detected." REFERENCE "{ISIS.aoi corruptedLSPsDetected (19)}" ::= { isisSysEntry 15 } isisSysLSPL1DbaseOloads OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the LSP L1 database has become overloaded." REFERENCE "{ISIS.aoi lSPL1DatabaseOverloads (20)}" ::= { isisSysEntry 16 } isisSysManAddrDropFromAreas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a manual address has been dropped from the area." REFERENCE "{ISIS.aoi manualAddressesDroppedFromArea (21)}" ::= { isisSysEntry 17 } isisSysAttmptToExMaxSeqNums OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the IS has attempted to exceed the maximum sequence number." REFERENCE "{ISIS.aoi attemptsToExceedmaximumSequenceNumber (22)}" ::= { isisSysEntry 18 } isisSysSeqNumSkips OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a sequence number skip has occurred." REFERENCE "{ISIS.aoi sequenceNumberSkips (23)}" ::= { isisSysEntry 19 } isisSysOwnLSPPurges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a zero-aged copy of the system's own LSP is received from some other node." REFERENCE "{ISIS.aoi ownLSPPurges (24)}" ::= { isisSysEntry 20 } isisSysIDFieldLenMismatches OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a PDU is received with a different value for ID field length to that of the receiving system." REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}" ::= { isisSysEntry 21 } isisSysMaxAreaAddrMismatches OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a PDU is received with a different value for MaximumAreaAddresses from that of the receiving system." REFERENCE "{ISIS.aoi MaximumAreaAddressesMismatches (118)}" ::= { isisSysEntry 22 } -- The following objects map those from the cLNSISISLevel2-P -- Package isisSysOrigL2LSPBuffSize OBJECT-TYPE SYNTAX LSPBuffSize MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum size of Level 2 LSPs and SNPs originated by this system. This object follows the replaceOnlyWhileDisabled behaviour." REFERENCE "{ISIS.aoi originatingL2LSPBufferSize (26)}" DEFVAL { 1492 } ::= { isisSysEntry 23 } isisSysL2State OBJECT-TYPE SYNTAX LevelState MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Level 2 database." REFERENCE "{ISIS.aoi l2State (28)}" ::= { isisSysEntry 24 } isisSysLSPL2DbaseOloads OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the Level 2 LSP database has become overloaded." REFERENCE "{ISIS.aoi lSPL2DatabaseOverloads (32)}" ::= { isisSysEntry 25 } isisSysAuthFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of authentication failures recognized by this instance of the protocol." ::= { isisSysEntry 26 } isisSysLSPIgnoreErrors OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, allow the router to ignore IS-IS link state packets (LSPs) that are received with internal checksum errors rather than purging the LSPs." DEFVAL { false } ::= { isisSysEntry 27 } isisSysLogAdjacencyChanges OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, causes IS-IS to generate a log message when an IS-IS adjacency changes state (up or down)." DEFVAL { false } ::= { isisSysEntry 28 } isisSysPartChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "partition changes" ::= { isisSysEntry 29 } isisSysMaxAreaCheck OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When on, enables checking of maximum area addresses per IS version of ISO10589." DEFVAL { true } ::= { isisSysEntry 30 } isisSysNextCircIndex OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to assign values to isisCircIndex as described in 'Textual Conventions for SNMPv2'. The network manager reads this object, and then writes the value back as the isisCircIndex in a SET that creates a new instance of isisCircEntry. If the SET fails with the code 'inconsistentValue', then the process must be repeated; If the SET succeeds, then the object is incremented, and the new instance is created according to the manager's directions." ::= { isisSysEntry 31 } isisSysExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the ISIS router. Turning this off forces the router to forget all current state" DEFVAL { active } ::= { isisSysEntry 32 } isisSysL2toL1Leaking OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, allow the router to leak L2 routes into L1." DEFVAL { false } ::= { isisSysEntry 33 } isisSysSetOverload OBJECT-TYPE SYNTAX INTEGER { setL1Overload(1), setL2Overload(2), setL1L2Overload(3), overloadClear(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Administrativly set the overload bit for each level. The overload bit will continue to be set if the implementation runs out of memory, independent of this variable" DEFVAL {overloadClear } ::= { isisSysEntry 34 } -- The Level 1 Manual Area Address Table -- contains the set of area addresses manually configured -- for each instance of the Integrated IS-IS protocol. -- At least one row in which the value of -- isisManAreaAddrExistState -- is on must be present for each instance of the protocol -- when isisSysAdminState is also on for that instance. The -- maximum number of rows in this table for each instance of -- the protocol for which the object isisManAreaAddrExistState -- has the value on is the value of isisSysMaxAreaAddresses. -- An Attempt to create a new row such that the number of -- rows with isisManAreaAddrExistState set to on for that -- protocol instance exceeds isisSysMaxAreaAddresses -- is rejected." isisManAreaAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisManAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The set of manual area addresses configured on this Intermediate System." REFERENCE "{ISIS.aoi manualAreaAddresses (10)}" ::= { isisSystem 2 } isisManAreaAddrEntry OBJECT-TYPE SYNTAX IsisManAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one area address manually configured on this system" INDEX { isisSysInstance, isisManAreaAddr } ::= { isisManAreaAddrTable 1 } IsisManAreaAddrEntry ::= SEQUENCE { isisManAreaAddr OSINSAddress, isisManAreaAddrExistState RowStatus } isisManAreaAddr OBJECT-TYPE SYNTAX OSINSAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "A manually configured area address for this system. This object follows the index behaviour. Note: an index for the entry {1, {49.0001} active} in this table would be the ordered pair (1, (0x03 0x49 0x00 0x01)), as the length of an Octet string is part of the OID." ::= { isisManAreaAddrEntry 1 } isisManAreaAddrExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the isisManAreaAddrEntry. This object follows the Row Status behaviour. If an attempt is made to set this object to the value destroy when the corresponding isisManAreaAddrEntry is the only valid entry for this instance and when the corresponding ISIS instance has isisSysAdminState set to 'on' then the attempt to delete the row is rejected." DEFVAL { active } ::= { isisManAreaAddrEntry 2 } -- The Level 1 Area Address Table -- The Level 1 Area Address Table contains the -- union of the sets of area addresses reported in all Level 1 -- LSPs received by this Intermediate System. isisAreaAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The union of the sets of area addresses reported in all Level 1 LSPs received by this instance of the protocol." REFERENCE "{ISIS.aoi areaAddresses (18)}" ::= { isisSystem 3 } isisAreaAddrEntry OBJECT-TYPE SYNTAX IsisAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one area address reported in a Level 1 LSP received by this instance of the protocol." INDEX { isisSysInstance, isisAreaAddr } ::= { isisAreaAddrTable 1 } IsisAreaAddrEntry ::= SEQUENCE { isisAreaAddr OSINSAddress } isisAreaAddr OBJECT-TYPE SYNTAX OSINSAddress MAX-ACCESS read-only STATUS current DESCRIPTION "An area address reported in a Level 1 LSP received by this instance of the protocol." ::= { isisAreaAddrEntry 1 } -- The System Integrated Group -- The System Integrated Group is present if the system -- supports Integrated ISIS at Level 1. -- The System Protocol Supported Table -- The System Protocol Supported Table contains the manually -- configured set of protocols supported by each -- instance of the Integrated ISIS protocol. -- isisSysProtSuppTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisSysProtSuppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the manually configured set of protocols supported by each instance of the Integrated ISIS protocol." ::= { isisSystem 4 } isisSysProtSuppEntry OBJECT-TYPE SYNTAX IsisSysProtSuppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one protocol supported by an instance of the Integrated ISIS protocol." INDEX { isisSysInstance, isisSysProtSuppProtocol } ::= { isisSysProtSuppTable 1 } IsisSysProtSuppEntry ::= SEQUENCE { isisSysProtSuppProtocol SupportedProtocol, isisSysProtSuppExistState RowStatus } isisSysProtSuppProtocol OBJECT-TYPE SYNTAX SupportedProtocol MAX-ACCESS not-accessible STATUS current DESCRIPTION "One supported protocol. This object follows the index behaviour." ::= { isisSysProtSuppEntry 1 } isisSysProtSuppExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the isisSysProtSuppEntry. This object follows the RowStatus behavior." DEFVAL { active } ::= { isisSysProtSuppEntry 2 } -- The Summary Address Table -- The Summary Address Table contains the set of summary -- addresses manually configured for each instance of -- IP Integrated ISIS on the system. isisSummAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisSummAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The set of IP summary addresses to use in forming summary TLVs originated by this Intermediate System. An administrator may use a summary address to combine and modify IP Reachability announcements. If the Intermediate system can reach any subset of the summary address, the summary address will be announced instead, at the configured metric." ::= { isisSystem 5 } isisSummAddrEntry OBJECT-TYPE SYNTAX IsisSummAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one IP summary address." INDEX { isisSysInstance, isisSummAddressType, isisSummAddress, isisSummAddrPrefixLen } ::= { isisSummAddrTable 1 } IsisSummAddrEntry ::= SEQUENCE { isisSummAddressType InetAddressType, isisSummAddress InetAddress, isisSummAddrPrefixLen InetAddressPrefixLength, isisSummAddrExistState RowStatus, isisSummAddrAdminState INTEGER, isisSummAddrDefaultMetric DefaultMetric } isisSummAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Type of IP address for this summary address. This object follows the index behaviour." ::= { isisSummAddrEntry 1 } isisSummAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address value for this summary address. This object follows the index behaviour." ::= { isisSummAddrEntry 2 } isisSummAddrPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Length of the IP NetMask for this summary address." ::= { isisSummAddrEntry 3 } isisSummAddrExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The existence state of this summary address. This object follows the row status behaviour." DEFVAL { active } ::= { isisSummAddrEntry 4 } isisSummAddrAdminState OBJECT-TYPE SYNTAX INTEGER { summaryL1(1), summaryL2(2), summaryL1L2(3), summaryOff(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative state of this entry. When the administrative state changes, if the new value would cause the contents of LSPs originated by the system to change, then those new LSPs must be generated and sent as soon as is permitted by the ISIS protocol." DEFVAL { summaryOff } ::= { isisSummAddrEntry 5 } isisSummAddrDefaultMetric OBJECT-TYPE SYNTAX DefaultMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The default metric value to announce this summary address with in LSPs generated by this system." DEFVAL { 20 } ::= { isisSummAddrEntry 6 } -- The Circuit Group -- The Circuit Group is current -- The Circuit Table -- Each broadcast or point-to-point interface on the system -- corresponds to one entry in the Circuit table. There may be -- many X.25 DA circuit entries in the Circuit table for an -- X.25 interface. isisCircTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisCircEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of circuits used by each instance of Integrated IS-IS on this system." ::= { isisCirc 1 } isisCircEntry OBJECT-TYPE SYNTAX IsisCircEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An isisCircEntry exists for each circuit used by Integrated IS-IS on this system." INDEX { isisSysInstance, isisCircIndex } ::= { isisCircTable 1 } IsisCircEntry ::= SEQUENCE { isisCircIndex Integer32, isisCircIfIndex Integer32, isisCircIfSubIndex Integer32, isisCircLocalID Integer32, isisCircAdminState AdminState, isisCircExistState RowStatus, isisCircType INTEGER, isisCircExtDomain TruthValue, isisCircAdjChanges Counter32, isisCircInitFails Counter32, isisCircRejAdjs Counter32, isisCircOutCtrlPDUs Counter32, isisCircInCtrlPDUs Counter32, isisCircIDFieldLenMismatches Counter32, isisCircLevel INTEGER, isisCircMCAddr INTEGER, isisCircPtToPtCircID CircuitID, isisCircPassiveCircuit TruthValue, isisCircMeshGroupEnabled INTEGER, isisCircMeshGroup Integer32, isisCircSmallHellos AdminState, isisCircUpTime UpTime } isisCircIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier of this circuit, unique within the instance of the protocol. This object follows the index behaviour. This is for SNMP Indexing purposes only and has no relation to any protocol value." ::= { isisCircEntry 1 } isisCircIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The value of ifIndex for the interface to which this circuit corresponds. This object cannot be modified after creation" ::= { isisCircEntry 2 } isisCircIfSubIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "A specifier for the part of the interface ifIndex to which this circuit corresponds, such as a DLCI or VPI/VCI. This object cannot be modified after creation" ::= { isisCircEntry 3 } isisCircLocalID OBJECT-TYPE SYNTAX Integer32(0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "An identification that can be used in protocol packets to identify a circuit. Values of isisCircLocalID do not need to be unique. They are only required to differ on LANs where the Intermediate System is the Designated Intermediate System." ::= { isisCircEntry 4 } isisCircAdminState OBJECT-TYPE SYNTAX AdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative state of the circuit. This object follows the AdminState behaviour." DEFVAL { off } ::= { isisCircEntry 5 } isisCircExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The existence state of this circuit. This object follows the Row Status behaviour." DEFVAL { active } ::= { isisCircEntry 6 } isisCircType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), ptToPt(2), staticIn(3), staticOut(4), dA(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the circuit. This object follows the replaceOnlyWhileDisabled behaviour. The type specified must be compatible with the type of the interface defined by the value of isisCircIfIndex." REFERENCE "{ISIS.aoi type (33)}" ::= { isisCircEntry 7 } isisCircExtDomain OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If true, suppress normal transmission of and interpretation of Intra-domain ISIS PDUs on this circuit." REFERENCE "{ISIS.aoi externalDomain (46)}" DEFVAL { false } ::= { isisCircEntry 8 } isisCircAdjChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an adjacency state change has occurred on this circuit." REFERENCE "{ISIS.aoi changesInAdjacencyState (40)}" ::= { isisCircEntry 14 } isisCircInitFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times initialization of this circuit has failed." REFERENCE "{ISIS.aoi initializationFailures (41)}" ::= { isisCircEntry 15 } isisCircRejAdjs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an adjacency has been rejected on this circuit." REFERENCE "{ISIS.aoi rejectedAdjacencies (42)}" ::= { isisCircEntry 16 } isisCircOutCtrlPDUs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS control PDUs sent on this circuit." REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}" ::= { isisCircEntry 17 } isisCircInCtrlPDUs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS control PDUs received on this circuit." REFERENCE "{ISIS.aoi controlPDUsReceived (44)}" ::= { isisCircEntry 18 } isisCircIDFieldLenMismatches OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an IS-IS control PDU with an ID field length different to that for this system has been received." REFERENCE "{ISIS.aoi iDFieldLengthMismatches (25)}" ::= { isisCircEntry 19 } isisCircLevel OBJECT-TYPE SYNTAX INTEGER { level1(1), level2(2), level1L2(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates which type of packets will be sent and accepted on this circuit. The values used will be modified by the settings of isisSysType. This object follows the replaceOnlyWhileDisabled behaviour." DEFVAL { level1L2 } ::= { isisCircEntry 20 } isisCircMCAddr OBJECT-TYPE SYNTAX INTEGER{ group (1), functional (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies which type of multicast address will be used for sending HELLO PDUs on this circuit." DEFVAL { group } ::= { isisCircEntry 21 } isisCircPtToPtCircID OBJECT-TYPE SYNTAX CircuitID MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the circuit allocated during initialization. If no value has been negotiated (either because the adjacency is to an End System, or because initialization has not yet successfully completed), this object has the value which would be proposed for this circuit (i.e. the concatenation of the local system ID and the one octet local Circuit ID for this circuit." REFERENCE "{ISIS.aoi ptPtCircuitID (51)}" ::= { isisCircEntry 22 } isisCircPassiveCircuit OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Should we include this interface in LSPs, even if it is not running the ISIS Protocol?" REFERENCE "{}" DEFVAL { false } ::= { isisCircEntry 23 } isisCircMeshGroupEnabled OBJECT-TYPE SYNTAX INTEGER { inactive(1), blocked(2), set(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Is this port a member of a mesh group, or blocked? Circuits in the same mesh group act as a virtual multiaccess network. LSPs seen on one circuit in a mesh group will not be flooded to another circuit in the same mesh group." REFERENCE "{}" DEFVAL { inactive } ::= { isisCircEntry 24 } isisCircMeshGroup OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS read-create STATUS current DESCRIPTION "Circuits in the same mesh group act as a virtual multiaccess network. LSPs seen on one circuit in a mesh group will not be flooded to another circuit in the same mesh group. If isisCircMeshGroupEnabled is inactive, this value is ignored." REFERENCE "{}" DEFVAL { 1 } ::= { isisCircEntry 25 } isisCircSmallHellos OBJECT-TYPE SYNTAX AdminState MAX-ACCESS read-create STATUS current DESCRIPTION "Can we send unpadded hellos on LAN circuits? Off means LAN Hellos must be padded." DEFVAL { off } ::= { isisCircEntry 26 } isisCircUpTime OBJECT-TYPE SYNTAX UpTime MAX-ACCESS read-only STATUS current DESCRIPTION "If the circuit is up, the amount of time in seconds since this circuit entered state 'up'. If the circuit is not up, the number of seconds since the circuit was up, or since the system started, if the circuit has never been up. Note: This can be implemented as start time less the current time." ::= { isisCircEntry 27 } -- The Circuit Level Table -- This table captures level-specific information about a circuit isisCircLevelTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisCircLevelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Level specific information about circuits used by IS-IS" ::= { isisCircLevelValues 1 } isisCircLevelEntry OBJECT-TYPE SYNTAX IsisCircLevelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An isisCircLevelEntry exists for each level on each circuit used by Integrated IS-IS on this system." INDEX { isisSysInstance, isisCircIndex, isisCircLevelIndex } ::= { isisCircLevelTable 1 } IsisCircLevelEntry ::= SEQUENCE { isisCircLevelIndex INTEGER, isisCircLevelDefaultMetric DefaultMetric, isisCircLevelISPriority ISPriority, isisCircLevelCircID CircuitID, isisCircLevelDesIS SystemID, isisCircLevelLANDesISChanges Counter32, isisCircLevelHelloMultiplier Integer32, isisCircLevelHelloTimer Integer32, isisCircLevelDRHelloTimer Integer32, isisCircLevelLSPThrottle Integer32, isisCircLevelMinLSPRetransInt Integer32, isisCircLevelCSNPInterval Integer32, isisCircLevelPartSNPInterval Integer32 } isisCircLevelIndex OBJECT-TYPE SYNTAX INTEGER { level1IS (1), level2IS (2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The level that this entry describes." ::= { isisCircLevelEntry 1 } isisCircLevelDefaultMetric OBJECT-TYPE SYNTAX DefaultMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The default metric value of this circuit for this level." REFERENCE "{ISIS.aoi l1DefaultMetric (35)}" DEFVAL { 10 } ::= { isisCircLevelEntry 2 } isisCircLevelISPriority OBJECT-TYPE SYNTAX ISPriority MAX-ACCESS read-create STATUS current DESCRIPTION "The priority for becoming LAN Designated Intermediate System at this level." REFERENCE "{ISIS.aoi l2IntermediateSystemPriority (73)}" DEFVAL { 64 } ::= { isisCircLevelEntry 3 } isisCircLevelCircID OBJECT-TYPE SYNTAX CircuitID MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the circuit allocated during initialization. If no value has been negotiated (either because the adjacency is to an End System, or because initialization has not yet successfully completed), this object has the value which would be proposed for this circuit (i.e. the concatenation of the local system ID and the one octet local Circuit ID for this circuit." REFERENCE "{ISIS.aoi ptPtCircuitID (51)}" ::= { isisCircLevelEntry 4 } isisCircLevelDesIS OBJECT-TYPE SYNTAX SystemID MAX-ACCESS read-only STATUS current DESCRIPTION "The ID of the LAN Designated Intermediate System on this circuit at this level. If, for any reason, this system is not partaking in the relevant Designated Intermediate System election process, then the value returned is the zero length OCTET STRING." REFERENCE "{ISIS.aoi l2DesignatedIntermediateSystem (75)}" ::= { isisCircLevelEntry 5 } isisCircLevelLANDesISChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the LAN Designated Intermediate System has changed at this level." REFERENCE "{ISIS.aoi lanL2DesignatedIntermediateSystemChanges (76)}" ::= { isisCircLevelEntry 6 } isisCircLevelHelloMultiplier OBJECT-TYPE SYNTAX Integer32 (2..100) MAX-ACCESS read-create STATUS current DESCRIPTION "This value is multiplied by the corresponding HelloTimer and the result in seconds (rounded up) is used as the holding time in transmitted hellos, to be used by receivers of hello packets from this IS" REFERENCE "{ISIS.aoi iSISHelloTimer (45)}" DEFVAL { 10 } ::= { isisCircLevelEntry 7 } isisCircLevelHelloTimer OBJECT-TYPE SYNTAX Integer32 (10..600000) MAX-ACCESS read-create STATUS current DESCRIPTION "Maximum period, in milliseconds, between IIH PDUs on multiaccess networks at this level for LANs. The value at level 1 is used as the period between Hellos on point to point circuits. Setting this value at level 2 on a point to point circuit will result in an error of InconsistentValue. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi iSISHelloTimer (45)}" DEFVAL { 3000 } ::= { isisCircLevelEntry 8 } isisCircLevelDRHelloTimer OBJECT-TYPE SYNTAX Integer32 (10..120000) MAX-ACCESS read-create STATUS current DESCRIPTION "Period, in milliseconds, between Hello PDUs on multiaccess networks when this IS is the Designated Intermediate System. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi iSISHelloTimer (45)}" DEFVAL { 1000 } ::= { isisCircLevelEntry 9 } isisCircLevelLSPThrottle OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Minimal interval of time, in milliseconds, between transmissions of LSPs on an interface at this level." REFERENCE "{ISIS.aoi minimumBroadcastLSPTransmissionInterval (5)}" DEFVAL { 10 } ::= { isisCircLevelEntry 10 } isisCircLevelMinLSPRetransInt OBJECT-TYPE SYNTAX Integer32 (1..300) MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum interval, in seconds, between re-transmission of an LSP at this level. This object follows the resettingTimer behavior. Note that isisCircLevelLSPThrottle controls how fast we send back to back LSPs. This variable controls how fast we re-send the same LSP." REFERENCE "{ISIS.aoi minimumLSPTransmissionInterval (5)}" DEFVAL { 5 } ::= { isisCircLevelEntry 11 } isisCircLevelCSNPInterval OBJECT-TYPE SYNTAX Integer32 (1..600) MAX-ACCESS read-create STATUS current DESCRIPTION "Interval of time, in seconds, between transmission of CSNPs on multiaccess networks if this router is the designated router at this level." REFERENCE "{}" DEFVAL { 10 } ::= { isisCircLevelEntry 12 } isisCircLevelPartSNPInterval OBJECT-TYPE SYNTAX Integer32 (1..120) MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum interval between sending Partial Sequence Number PDUs at this level. This object follows the resettingTimer behaviour." REFERENCE "{ISIS.aoi partialSNPInterval (14)}" DEFVAL { 2 } ::= { isisCircLevelEntry 13 } -- isisPacketCountTable keeps track of the number of IS-IS -- control packets sent and received at each level isisPacketCountTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisPacketCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about IS-IS packets sent and received" ::= { isisCircPDUCounters 1 } isisPacketCountEntry OBJECT-TYPE SYNTAX IsisPacketCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about IS-IS protocol traffic at one level on one circuit in one direction" INDEX { isisSysInstance, isisCircIndex, isisPacketCountLevel, isisPacketCountDirection } ::= { isisPacketCountTable 1 } IsisPacketCountEntry ::= SEQUENCE { isisPacketCountLevel INTEGER, isisPacketCountDirection INTEGER, isisPacketCountHello Counter32, isisPacketCountLSP Counter32, isisPacketCountCSNP Counter32, isisPacketCountPSNP Counter32 } isisPacketCountLevel OBJECT-TYPE SYNTAX INTEGER { level1(1), level2(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The level at which these PDU counts have been collected." ::= { isisPacketCountEntry 1 } isisPacketCountDirection OBJECT-TYPE SYNTAX INTEGER { sending(1), receiving(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Were we sending or receiving these PDUs?" ::= { isisPacketCountEntry 2 } isisPacketCountHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS Hello PDUs seen in this direction at this level." REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}" ::= { isisPacketCountEntry 3 } isisPacketCountLSP OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS LSPs seen in this direction at this level." REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}" ::= { isisPacketCountEntry 4 } isisPacketCountCSNP OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS CSNPs seen in this direction at this level." REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}" ::= { isisPacketCountEntry 5 } isisPacketCountPSNP OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IS-IS PSNPs seen in this direction at this level." REFERENCE "{ISIS.aoi iSISControlPDUsSent (43)}" ::= { isisPacketCountEntry 6 } -- The Circuit IS Group -- -- The Circuit IS Group is present if the system supports the -- IS functions of the ISO 9542 protocol. -- The Circuit IS Table -- -- This table is not implemented - jdp -- The IS Adjacency Group -- -- The IS Adjacency Group is current and contains information -- about adjacencies to routers maintained by the Integrated -- IS-IS protocol -- -- The IS Adjacency Table -- -- Each adjacency to an IS corresponds to one entry in this -- table. isisISAdjTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisISAdjEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of adjacencies to Intermediate Systems." ::= { isisISAdj 1 } isisISAdjEntry OBJECT-TYPE SYNTAX IsisISAdjEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry corresponds to one adjacency to an Intermediate System on this system." INDEX { isisSysInstance, isisCircIndex, isisISAdjIndex } ::= { isisISAdjTable 1 } IsisISAdjEntry ::= SEQUENCE { isisISAdjIndex Integer32, isisISAdjState INTEGER, isisISAdjNeighSNPAAddress SNPAAddress, isisISAdjNeighSysType INTEGER, isisISAdjNeighSysID OCTET STRING, isisISAdjUsage INTEGER, isisISAdjHoldTimer Integer32, isisISAdjNeighPriority ISPriority, isisISAdjUpTime UpTime } isisISAdjIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value identifying the IS adjacency from all other such adjacencies on this circuit. This value is assigned by the system when the adjacency is created automatically." ::= { isisISAdjEntry 1 } isisISAdjState OBJECT-TYPE SYNTAX INTEGER { initializing (1), up (2), failed (3), down (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the adjacency" REFERENCE "{ISIS.aoi adjacencyState (78)}" ::= { isisISAdjEntry 2 } isisISAdjNeighSNPAAddress OBJECT-TYPE SYNTAX SNPAAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The SNPA address of the neighboring system." REFERENCE "{ISIS.aoi neighbourSNPAAddress (79)}" ::= { isisISAdjEntry 3 } isisISAdjNeighSysType OBJECT-TYPE SYNTAX INTEGER { l1IntermediateSystem(1), l2IntermediateSystem(2), l1L2IntermediateSystem(3), unknown(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the neighboring system." REFERENCE "{ISIS.aoi neighbourSystemType (80)}" ::= { isisISAdjEntry 4 } isisISAdjNeighSysID OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "The system ID and 4 byte circuit ID of the neighboring Intermediate System set from the source ID field of the Three-Way-Handshake information from the neighbor's IIH PDUs." REFERENCE "{ISIS.aoi neighbourSystemIds (83)}" ::= { isisISAdjEntry 5 } isisISAdjUsage OBJECT-TYPE SYNTAX INTEGER { undefined(1), level1(2), level2(3), level1and2(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "An adjacency of type level1 is used for level 1 traffic only. An adjacency of type level2 is used for level 2 traffic only. An adjacency of type level1and2 is used for both level 1 and level 2 traffic. There may be two adjacencies (of types level1 and level2) between the same pair of Intermediate Systems." REFERENCE "{ISIS.aoi adjacencyUsage (82)}" ::= { isisISAdjEntry 6 } isisISAdjHoldTimer OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The holding time for this adjacency updated from received IIH PDUs." REFERENCE "{ISIS.aoi holdingTimer (85)}" ::= { isisISAdjEntry 7 } isisISAdjNeighPriority OBJECT-TYPE SYNTAX ISPriority MAX-ACCESS read-only STATUS current DESCRIPTION "Priority of the neighboring Intermediate System for becoming the LAN Level 1 Designated Intermediate System if the value of isisISAdjNeighSysType is L1IntermediateSystem or LAN Level 2 Designated Intermediate System if the value of isisISAdjNeighSysType is L2IntermediateSystem." REFERENCE "{ISIS.aoi lANPriority (86)}" ::= { isisISAdjEntry 8 } isisISAdjUpTime OBJECT-TYPE SYNTAX UpTime MAX-ACCESS read-only STATUS current DESCRIPTION "If the adjacency is up, the amount of time in seconds since this adjacency entered state 'up'. If the adjacency is not up, the number of seconds since the adjacency was up, or since the system started, if the adjacency has never been up. Note: This can be implemented as start time less the current time." ::= { isisISAdjEntry 9 } -- The IS Adjacency Area Address Table -- The IS Adjacency Area Address Table contains the set of -- Area Addresses of neighboring -- Intermediate Systems as reported in IIH PDUs. isisISAdjAreaAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisISAdjAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the set of Area Addresses of neighboring Intermediate Systems as reported in received IIH PDUs." REFERENCE "{ISIS.aoi areaAddressesOfNeighbour (84)}" ::= { isisISAdj 2 } isisISAdjAreaAddrEntry OBJECT-TYPE SYNTAX IsisISAdjAreaAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one Area Address reported by a neighboring Intermediate System in its IIH PDUs." INDEX { isisSysInstance, isisCircIndex, isisISAdjAreaAddrAdjIndex, isisISAdjAreaAddress } ::= { isisISAdjAreaAddrTable 1 } IsisISAdjAreaAddrEntry ::= SEQUENCE { isisISAdjAreaAddrAdjIndex Integer32, isisISAdjAreaAddress OSINSAddress } isisISAdjAreaAddrAdjIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier of the IS adjacency to which this entry belongs." ::= { isisISAdjAreaAddrEntry 1 } isisISAdjAreaAddress OBJECT-TYPE SYNTAX OSINSAddress MAX-ACCESS read-only STATUS current DESCRIPTION "One Area Address as reported in IIH PDUs received from the neighbor." ::= { isisISAdjAreaAddrEntry 2 } -- The IS Adjacency IP Group -- The IS Adjacency IP Group is present if the system supports -- IP Integrated IS-IS -- The IS Adjacency IP Address Table -- The IS Adjacency IP Address Table contains the -- set of IP Addresses of neighboring Intermediate Systems -- as reported in received IIH PDUs. isisISAdjIPAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisISAdjIPAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the set of IP Addresses of neighboring Intermediate Systems as reported in received IIH PDUs." ::= { isisISAdj 3 } isisISAdjIPAddrEntry OBJECT-TYPE SYNTAX IsisISAdjIPAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one IP Address reported by a neighboring Intermediate System in its IIH PDUs." INDEX { isisSysInstance, isisCircIndex, isisISAdjIPAddrAdjIndex } ::= { isisISAdjIPAddrTable 1 } IsisISAdjIPAddrEntry ::= SEQUENCE { isisISAdjIPAddrAdjIndex Integer32, isisISAdjIPAddressType InetAddressType, isisISAdjIPAddress InetAddress } isisISAdjIPAddrAdjIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier of the IS adjacency to which this entry belongs." ::= { isisISAdjIPAddrEntry 1 } isisISAdjIPAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of one IP Address as reported in IIH PDUs received from the neighbor." ::= { isisISAdjIPAddrEntry 2 } isisISAdjIPAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-only STATUS current DESCRIPTION "One IP Address as reported in IIH PDUs received from the neighbor." ::= { isisISAdjIPAddrEntry 3 } -- The IS Adjacency Integrated Group -- -- The IS Adjacency Integrated Group is present if the system -- supports Integrated ISIS. -- -- -- The IS Adjacency Protocol Supported Table -- -- The IS Adjacency Protocol Supported Table contains the set of -- protocols supported by neighboring -- Intermediate Systems as reported in received IIH PDUs. -- isisISAdjProtSuppTable OBJECT-TYPE SYNTAX SEQUENCE OF IsisISAdjProtSuppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the set of protocols supported by neighboring Intermediate Systems as reported in received IIH PDUs." ::= { isisISAdj 4 } isisISAdjProtSuppEntry OBJECT-TYPE SYNTAX IsisISAdjProtSuppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one protocol supported by a neighboring Intermediate System as reported in its IIH PDUs." INDEX { isisSysInstance, isisCircIndex, isisISAdjProtSuppAdjIndex, isisISAdjProtSuppProtocol } ::= { isisISAdjProtSuppTable 1 } IsisISAdjProtSuppEntry ::= SEQUENCE { isisISAdjProtSuppAdjIndex Integer32, isisISAdjProtSuppProtocol SupportedProtocol } isisISAdjProtSuppAdjIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier the IS adjacency to which this entry corresponds." ::= { isisISAdjProtSuppEntry 1 } isisISAdjProtSuppProtocol OBJECT-TYPE SYNTAX SupportedProtocol MAX-ACCESS read-only STATUS current DESCRIPTION "One supported protocol as reported in IIH PDUs received from the neighbor." ::= { isisISAdjProtSuppEntry 2 } -- -- -- The ES Adjacency Group -- -- The ES Adjacency Group is present if the system supports -- reception of ES Hellos -- The ES Adjacency Table -- -- This table is not implemented - jdp -- -- -- The Reachable Address Group -- -- The Reachable Address Group is optional. -- The Reachable Address Table -- Each entry records information about a reachable address -- (NSAP or address prefix) manually configured on the system -- or learned through another protocol. isisRATable OBJECT-TYPE SYNTAX SEQUENCE OF IsisRAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Reachable Addresses to NSAPs or Address Prefixes." ::= { isisReachAddr 1 } isisRAEntry OBJECT-TYPE SYNTAX IsisRAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry defines a Reachable Address to a NSAP or Address Prefix." INDEX { isisSysInstance, isisCircIndex, isisRAIndex } ::= { isisRATable 1 } IsisRAEntry ::= SEQUENCE { isisRAIndex Integer32, isisRAExistState RowStatus, isisRAAdminState AdminState, isisRAAddrPrefix NSAPPrefix, isisRAMapType INTEGER, isisRADefMetric DefaultMetric, isisRADefMetricType MetricType, isisRASNPAAddress SNPAAddress, isisRASNPAMask SNPAPrefix, isisRASNPAPrefix SNPAPrefix, isisRAType INTEGER } isisRAIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier for this isisRAEntry. This value must be unique amongst all Reachable Addresses on the same parent Circuit. This object follows the index and manualOrAutomatic behaviours." ::= { isisRAEntry 1 } isisRAExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The existence state of this Reachable Address. This object follows the Row Status behaviours." DEFVAL { active } ::= { isisRAEntry 2 } isisRAAdminState OBJECT-TYPE SYNTAX AdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative state of the Reachable Address. This object follows the AdminState and manualOrAutomatic behaviours." DEFVAL { off } ::= { isisRAEntry 3 } isisRAAddrPrefix OBJECT-TYPE SYNTAX NSAPPrefix MAX-ACCESS read-create STATUS current DESCRIPTION "The destination of this Reachable Address. This is an Address Prefix. This object follows the replaceOnlyWhileDisabled and manualOrAutomatic behaviours." REFERENCE "{ISIS.aoi addressPrefix (98)}" ::= { isisRAEntry 4 } isisRAMapType OBJECT-TYPE SYNTAX INTEGER { none (1), explicit (2), extractIDI (3), extractDSP (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of mapping to be employed to ascertain the SNPA Address which should be used in forwarding PDUs for this Reachable Address prefix. This object follows the manualOrAutomatic behaviour. The following values of mapping type are defined: none: The mapping is null because the neighbor SNPA is implicit by nature of the subnetwork (e.g. a point-to-point linkage). explicit: The subnetwork addresses in the object isisRASNPAAddress is to be used. extractIDI: The SNPA is embedded in the IDI of the destination NSAP Address. The mapping algorithm extracts the SNPA to be used according to the format and encoding rules of ISO8473/Add2. This SNPA extraction algorithm can be used in conjunction with Reachable Address prefixes from the X.121, F.69, E.163 and E.164 addressing subdomains. extractDSP: All, or a suffix, of the SNPA is embedded in the DSP of the destination address. This SNPA extraction algorithm extracts the embedded subnetwork addressing information by performing a logical AND of the isisRASNPAMask object value with the destination address. The part of the SNPA extracted from the destination NSAP is appended to the isisRASNPAPrefix object value to form the next hop subnetwork addressing information." REFERENCE "{ISO10589-ISIS.aoi mappingType (107)}" ::= { isisRAEntry 5 } isisRADefMetric OBJECT-TYPE SYNTAX DefaultMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The default metric value for reaching the specified prefix over this circuit. This object follows the manualOrAutomatic behaviour." REFERENCE "{ISIS.aoi DefaultMetric (99)}" DEFVAL { 20 } ::= { isisRAEntry 6 } isisRADefMetricType OBJECT-TYPE SYNTAX MetricType MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the default metric is internal or external. This object follows the manualOrAutomatic behaviour." REFERENCE "{ISIS.aoi DefaultMetricType (103)}" DEFVAL { internal } ::= { isisRAEntry 7 } isisRASNPAAddress OBJECT-TYPE SYNTAX SNPAAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The SNPA Address to which a PDU may be forwarded in order to reach a destination which matches the address prefix of the Reachable Address. This object follows the manualOrAutomatic behaviour." REFERENCE "{ISIS.aoi sNPAAddresses (109)}" -- note only one address may be specified per Reachable Address -- in the MIB DEFVAL { ''H } ::= { isisRAEntry 8 } isisRASNPAMask OBJECT-TYPE SYNTAX SNPAPrefix MAX-ACCESS read-create STATUS current DESCRIPTION "A bit mask with 1 bits indicating the positions in the effective destination address from which embedded SNPA information is to be extracted. For the extraction the first octet of the isisRASNPAMask object value is aligned with the first octet (AFI) of the NSAP Address. If the isisRASNPAMask object value and NSAP Address are of different lengths, the shorter of the two is logically padded with zeros before performing the extraction. This object follows the manualOrAutomatic behaviour." REFERENCE "{ISIS.aoi sNPAMask (122)}" DEFVAL { '00'H } ::= { isisRAEntry 9 } isisRASNPAPrefix OBJECT-TYPE SYNTAX SNPAPrefix MAX-ACCESS read-create STATUS current DESCRIPTION "A fixed SNPA prefix for use when the isisRAMapType is extractDSP. The SNPA Address to use is formed by concatenating the fixed SNPA prefix with a variable SNPA part that is extracted from the effective destination address. For Reachable Address prefixes in which the entire SNPA is embedded in the DSP the SNPA Prefix shall be null. This object follows the manualOrAutomatic behaviour." REFERENCE "{ISIS.aoi sNPAPrefix (123)}" DEFVAL { '00'H } ::= { isisRAEntry 10 } isisRAType OBJECT-TYPE SYNTAX INTEGER { manual (1), automatic (2) } MAX-ACCESS read-create STATUS current DESCRIPTION " The type of Reachable address. Those of type manual are created by the network manager. Those of type automatic are created through propogation of routing information from another routing protocol (eg. IDRP). " DEFVAL {manual} ::= {isisRAEntry 11 } -- The IP Reachable Address Group -- The IP Reachable Address Group is optional. -- The IP Reachable Address Table -- Each entry records information about one IP reachable -- address manually configured on this system or learned from -- another protocol. isisIPRATable OBJECT-TYPE SYNTAX SEQUENCE OF IsisIPRAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP Reachable Addresses to networks, subnetworks or hosts either manually configured or learned from another protocol." ::= { isisIPReachAddr 1 } isisIPRAEntry OBJECT-TYPE SYNTAX IsisIPRAEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry defines an IP Reachable Address to a network, subnetwork or host." INDEX { isisSysInstance, isisCircIndex, isisIPRAType, isisIPRAIndex } ::= { isisIPRATable 1 } IsisIPRAEntry ::= SEQUENCE { isisIPRAIndex Integer32, isisIPRAType INTEGER, isisIPRADestType InetAddressType, isisIPRADest InetAddress, isisIPRADestPrefixLen InetAddressPrefixLength, isisIPRAExistState RowStatus, isisIPRAAdminState AdminState, isisIPRADefMetric DefaultMetric, isisIPRADefMetricType MetricType, isisIPRASNPAAddress SNPAAddress } isisIPRAIndex OBJECT-TYPE SYNTAX Integer32 (1..2000000000) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identifier for this isisIPRAEntry. This value must be unique amongst all IP Reachable Addresses on the same parent Circuit. This object follows the index and manualOrAutomatic behaviours." ::= { isisIPRAEntry 1 } isisIPRAType OBJECT-TYPE SYNTAX INTEGER { manual (1), automatic (2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of this IP Reachable Address. Those of type manual are created by the network manager. Those of type automatic are created through propagation of routing information from another routing protocol." ::= { isisIPRAEntry 2 } isisIPRADestType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of this IP Reachable Address." ::= { isisIPRAEntry 3 } isisIPRADest OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The destination of this IP Reachable Address. This is either a network address, subnetwork address or host address. This object follows the manualOrAutomatic behaviour." ::= { isisIPRAEntry 4 } isisIPRADestPrefixLen OBJECT-TYPE SYNTAX InetAddressPrefixLength (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The length of the IP Netmask for Reachability Address." ::= { isisIPRAEntry 5 } isisIPRAExistState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The state of this IP Reachable Address. This object follows the ExistenceState and manualOrAutomatic behaviours." DEFVAL { active } ::= { isisIPRAEntry 6 } isisIPRAAdminState OBJECT-TYPE SYNTAX AdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The administrative state of the IP Reachable Address. This object follows the AdminState and manualOrAutomatic behaviours." DEFVAL { off } ::= { isisIPRAEntry 7 } isisIPRADefMetric OBJECT-TYPE SYNTAX DefaultMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The default metric value for reaching the specified destination over this circuit. This object follows the manualOrAutomatic behaviour." DEFVAL { 20 } ::= { isisIPRAEntry 8 } isisIPRADefMetricType OBJECT-TYPE SYNTAX MetricType MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the default metric is internal or external. This object follows the manualOrAutomatic behaviour." DEFVAL { internal } ::= { isisIPRAEntry 9 } isisIPRASNPAAddress OBJECT-TYPE SYNTAX SNPAAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The SNPA Address to which a PDU may be forwarded in order to reach a destination which matches this IP Reachable Address. This object follows the manualOrAutomatic behaviour." DEFVAL { ''H } ::= { isisIPRAEntry 10 } -- The Circuit CLNS Group -- -- The Circuit CLNS Table contains objects controlling the -- operation of the IS functions of the CLNS protocol -- -- This table is not implemented - jdp -- -- The IP Destination Group -- The IP Destination Group is present if the system forwards -- IP packets. -- The IP Destination Table -- The IP Destination Table records information about each -- destination known to the Intermediate System -- Removed: overlaps RFC 2096 - jdp -- Conformance Definitions isisGroups OBJECT IDENTIFIER ::= { isisConformance 1 } isisCompliances OBJECT IDENTIFIER ::= { isisConformance 2 } -- compliance statements isisCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compiance statement for agents that support the ISIS MIB" MODULE -- this module MANDATORY-GROUPS { isisSystemGroup, isisCircuitGroup, isisISAdjGroup } ::= { isisCompliances 1 } -- MIB Grouping isisSystemGroup OBJECT-GROUP OBJECTS { isisSysVersion, isisSysType, isisSysID, isisSysMaxPathSplits, isisSysMaxLSPGenInt, isisSysOrigL1LSPBuffSize, isisSysMaxAreaAddresses, isisSysMinL1LSPGenInt, isisSysMinL2LSPGenInt, isisSysPollESHelloRate, isisSysWaitTime, isisSysAdminState, isisSysL1State, isisSysCorrLSPs, isisSysLSPL1DbaseOloads, isisSysManAddrDropFromAreas, isisSysAttmptToExMaxSeqNums, isisSysSeqNumSkips, isisSysOwnLSPPurges, isisSysIDFieldLenMismatches, isisSysMaxAreaAddrMismatches, isisSysOrigL2LSPBuffSize, isisSysL2State, isisSysLSPL2DbaseOloads, isisSysAuthFails, isisSysLSPIgnoreErrors, isisSysLogAdjacencyChanges, isisSysPartChanges, isisSysMaxAreaCheck, isisSysNextCircIndex, isisSysExistState, isisSysL2toL1Leaking, isisSysSetOverload, isisManAreaAddrExistState, isisAreaAddr, isisSysProtSuppExistState, isisSummAddrExistState, isisSummAddrAdminState, isisSummAddrDefaultMetric } STATUS current DESCRIPTION "The collections of objects used to manage an IS-IS router." ::= { isisGroups 1 } isisCircuitGroup OBJECT-GROUP OBJECTS { isisCircIfSubIndex, isisCircLocalID, isisCircAdminState, isisCircExistState, isisCircType, isisCircExtDomain, isisCircAdjChanges, isisCircInitFails, isisCircRejAdjs, isisCircOutCtrlPDUs, isisCircInCtrlPDUs, isisCircIDFieldLenMismatches, isisCircLevel, isisCircMCAddr, isisCircPtToPtCircID, isisCircPassiveCircuit, isisCircMeshGroupEnabled, isisCircMeshGroup, isisCircSmallHellos, isisCircUpTime, isisCircIfIndex, isisCircLevelDefaultMetric, isisCircLevelISPriority, isisCircLevelCircID, isisCircLevelDesIS, isisCircLevelLANDesISChanges , isisCircLevelHelloMultiplier, isisCircLevelHelloTimer, isisCircLevelDRHelloTimer, isisCircLevelLSPThrottle, isisCircLevelMinLSPRetransInt, isisCircLevelCSNPInterval, isisCircLevelPartSNPInterval } STATUS current DESCRIPTION "The collection of objects used to describe in IS-IS Circuit." ::= { isisGroups 2 } isisISAdjGroup OBJECT-GROUP OBJECTS { isisISAdjState, isisISAdjNeighSNPAAddress, isisISAdjNeighSysType, isisISAdjNeighSysID, isisISAdjUsage, isisISAdjHoldTimer, isisISAdjNeighPriority, isisISAdjUpTime, isisISAdjAreaAddress, isisISAdjIPAddressType, isisISAdjIPAddress, isisISAdjProtSuppProtocol } STATUS current DESCRIPTION "The collections of objects used to manage an IS-IS Adjacency." ::= { isisGroups 3 } isisISPDUCounterGroup OBJECT-GROUP OBJECTS { isisPacketCountHello, isisPacketCountLSP, isisPacketCountCSNP, isisPacketCountPSNP } STATUS current DESCRIPTION "The collections of objects used to count various protocol PDUs." ::= { isisGroups 4 } isisRATableGroup OBJECT-GROUP OBJECTS { isisRAExistState, isisRAAdminState, isisRAAddrPrefix, isisRAMapType, isisRADefMetric, isisRADefMetricType, isisRASNPAAddress, isisRASNPAMask, isisRASNPAPrefix, isisRAType } STATUS current DESCRIPTION "The collections of objects used to manage the reachable NSAP prefixes." ::= { isisGroups 5 } isisISIPRADestGroup OBJECT-GROUP OBJECTS { isisIPRADestType, isisIPRADest, isisIPRADestPrefixLen, isisIPRAExistState, isisIPRAAdminState, isisIPRADefMetric, isisIPRADefMetricType, isisIPRASNPAAddress } STATUS current DESCRIPTION "The collections of objects used to manage configured IP addresses." ::= { isisGroups 6 } END -- -- -- Copyright (C) The Internet Society (1997). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this -- document itself may not be modified in any way, such as by removing -- the copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of -- developing Internet standards in which case the procedures for -- copyrights defined in the Internet Standards process must be -- followed, or as required to translate it into languages other than -- English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- -- This document and the information contained herein is provided on an -- "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING -- TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING -- BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION -- HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF -- MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE."