-- extracted from draft-ietf-mpls-bundle-mib-03.txt -- at Wed Jul 3 06:09:57 2002 LINK-BUNDLING-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue, RowStatus, StorageType FROM SNMPv2-TC InterfaceIndexOrZero, ifIndex FROM IF-MIB RouterID FROM OSPF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB; linkBundlingMIB MODULE-IDENTITY LAST-UPDATED "200206211200Z" -- 21 June 2002 12:00:00 EST ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group" CONTACT-INFO " Martin Dubuc Postal: Meriton Networks 3026 Solandt Road Kanata, ON, CANADA K2K 2A5 Tel: +1-613-270-9279 x253 Email: martin.dubuc@meriton.com Sudheer Dharanikota Postal: Nayna Networks, Inc. 157 Topaz Street Milipitas, CA 95035 Tel: +1-408-956-8000 x357 Email: sudheer@nayna.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 300 Apollo Drive Chelmsford, MA 01824 Tel: +1-978-244-3051 Email: tnadeau@cisco.com Jonathan P. Lang Postal: Calient Networks, Inc. 25 Castilian Drive Goleta, CA 93117 Email: jplang@calient.net" DESCRIPTION "This MIB contains managed object definitions for MPLS traffic engineering link bundling as defined in: Kompella, K., Rekhter, Y., Berger, L., Link Bundling in MPLS Traffic Engineering Internet Draft , May 2002." -- Revision history. REVISION "200206141200Z" -- 21 June 2002 12:00:00 EST DESCRIPTION "Addressed WG chair comments." REVISION "200205211200Z" -- 21 May 2002 12:00:00 EST DESCRIPTION "Addressed comments received during Last Call. - Addressed syntax errors reports by smilint. - Reintroduced teLinkIpAddrType. - Replaced ifIndex in linkBundlingMismatch notification with TE link endpoint objects." REVISION "200202261200Z" -- 26 February 2002 12:00:00 EST DESCRIPTION "- Updated MIB boiler plate and references. - Added linkBundlingFullModuleCompliance conformance statement. - Removed teLinkIpAddrType. Replaced numbered value with ipV4 and ipV6 values in teLinkNumberingType. - Updated description of all row status and storage type objects. - Changed some of the enumerated value to start from 1 instead of 0. - Updated references." REVISION "200109101200Z" -- 10 September 2001 12:00:00 EST DESCRIPTION "Removed teLinkRemoteId. Updated teLinkEncodingType and componentLinkEncodingType values." REVISION "200105221200Z" -- 22 May 2001 12:00:00 EST DESCRIPTION "Replaced InetAddressIPv4 and InetAddressIPv6 with InetAddress and InetAddrType. Changed description of entries which extend ifEntry. Made various minor corrections." REVISION "200105151200Z" -- 15 May 2001 12:00:00 EST DESCRIPTION "Replaced componentLinkTable by componentLinkTable. Replaced linkBundlingTable by teLinkTable. Converted TE links into interfaces." REVISION "200102231200Z" -- 23 February 2001 12:00:00 EST DESCRIPTION "Initial draft version." ::= { experimental 114 } -- See [Assigned] -- Textual Conventions -- Top level components of this MIB -- Notifications linkBundlingNotifications OBJECT IDENTIFIER ::= { linkBundlingMIB 0 } -- Tables, Scalars linkBundlingObjects OBJECT IDENTIFIER ::= { linkBundlingMIB 1 } -- Conformance linkBundlingConformance OBJECT IDENTIFIER ::= { linkBundlingMIB 2 } -- TE Link Table teLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the grouping of component links into TE links and grouping of TE links into bundled links." ::= { linkBundlingObjects 1 } teLinkEntry OBJECT-TYPE SYNTAX TeLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table exists for each ifEntry with an ifType of teLink(TBD), i.e. for every TE link. An ifEntry in the ifTable must exist before a teLinkEntry is created with the corresponding ifIndex. If a TE link entry in the ifTable is destroyed, then so is the corresponding entry in the teLinkTable. The administrative and operational status values are controlled from the ifEntry. If the link is unnumbered, ifIndex is also used as the outgoing interface identifier." INDEX { ifIndex } ::= { teLinkTable 1 } TeLinkEntry ::= SEQUENCE { teLinkIpAddrType InetAddressType, teLinkIpAddr InetAddress, teLinkRemoteIpAddr InetAddress, teLinkMetric Unsigned32, teLinkMuxCapability INTEGER, teLinkProtectionType INTEGER, teLinkWorkingPriority Unsigned32, teLinkResourceClass Unsigned32, teLinkIncomingIfId InterfaceIndexOrZero, teLinkOutgoingIfId InterfaceIndexOrZero, teLinkFlooding InterfaceIndexOrZero, teLinkRowStatus RowStatus, teLinkStorageType StorageType } teLinkIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "For IPv4 and IPv6 numbered links, this object represents the IP address type associated with the TE link. For unnumbered links, a value of unknown(0) must be used." ::= { teLinkEntry 1 } teLinkIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "For IPv4 and IPv6 numbered links, this object represents the IP address associated with the TE link." ::= { teLinkEntry 2 } teLinkRemoteIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The remote IP address associated with the TE link (IPv4 and IPv6 numbered links)." ::= { teLinkEntry 3 } teLinkMetric OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkEntry 4 } teLinkMuxCapability OBJECT-TYPE SYNTAX INTEGER { packetSwitch1(1), packetSwitch2(2), packetSwitch3(3), packetSwitch4(4), layer2Switch(51), tdm(100), lambdaSwitch(150), fiberSwitch(200) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link multiplex capability of the TE link, which is derived from its component links. All component links within the same TE link must have the same link multiplex capability." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkEntry 5 } teLinkProtectionType OBJECT-TYPE SYNTAX INTEGER { extraTraffic(1), unprotected(2), shared(3), dedicated1For1(4), dedicated1Plus1(5), enhanced(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link protection type of the TE link." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkEntry 6 } teLinkWorkingPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a priority value such that a new connection with a higher priority, i.e. numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkEntry 7 } teLinkResourceClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within a link bundle must have the same resource class." ::= { teLinkEntry 8 } teLinkIncomingIfId OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "For unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkEntry 9 } teLinkOutgoingIfId OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "If the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkEntry 10 } teLinkFlooding OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This object only has significance for link bundles which encoding type is not clear. For these link bundles, this object identifies the TE link on which to restrict flooding. If the value is zero, then flooding must be done on all TE links within the link bundle." REFERENCE "draft-ietf-ospf-isis-flood-opt-01.txt - Flooding optimization in link-state routing protocols, A. Zinin, M. Shand, March 2001." DEFVAL { 0 } ::= { teLinkEntry 11 } teLinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkRowStatus is active." ::= { teLinkEntry 12 } teLinkStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkEntry 13 } -- End of teLinkTable -- TE Link Descriptor Table teLinkDescriptorTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the link descriptors associated with the TE links." ::= { linkBundlingObjects 2 } teLinkDescriptorEntry OBJECT-TYPE SYNTAX TeLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created for every TE link descriptor. An ifEntry in the ifTable must exist before a teLinkDescriptorEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkDescriptorTable that use the ifIndex of this TE link." INDEX { ifIndex, teLinkDescriptorId } ::= { teLinkDescriptorTable 1 } TeLinkDescriptorEntry ::= SEQUENCE { teLinkDescriptorId Unsigned32, teLinkEncodingType INTEGER, teLinkDescrPriority Unsigned32, teLinkMinReservableBandwidth Unsigned32, teLinkMaxReservableBandwidth Unsigned32, teLinkDescrRowStatus RowStatus, teLinkDescrStorageType StorageType } teLinkDescriptorId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the link descriptor identifier." ::= { teLinkDescriptorEntry 1 } teLinkEncodingType OBJECT-TYPE SYNTAX INTEGER { packet(1), ethernet(2), ansiEtsiPdh(3), sdhItuSonetAnsi(5), digitalWrapper(7), lambda(8), fiber(9), fiberChannel(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link encoding type." REFERENCE "draft-ietf-mpls-generalized-signaling-08.txt - Generalized MPLS Signaling Functional Description, P. Ashwood-Smith, A. Banarjee, L. Berger, G. Bernstein, J. Drake, Y. Fan, E. Mannie, J. Lang, B. Rajagopalan, Y. Rekhter, D. Saha, V. Sharma, G. Swallow, Z. Tang, April 2002." ::= { teLinkDescriptorEntry 2 } teLinkDescrPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the lowest priority at which that link encoding type is available." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkDescriptorEntry 3 } teLinkMinReservableBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the minimum reservable bandwidth on the TE link. This is derived from the union of the minimum reservable bandwidth of all the component links associated with the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkDescriptorEntry 4 } teLinkMaxReservableBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkDescriptorEntry 5 } teLinkDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkDescrRowStatus is active." ::= { teLinkDescriptorEntry 6 } teLinkDescrStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkDescriptorEntry 7 } -- End of teLinkDescriptorTable -- OSPF Traffic Engineering Parameters for TE Links teLinkOspfTeTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkOspfTeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the OSPF traffic engineering information associated with TE links." ::= { linkBundlingObjects 3 } teLinkOspfTeEntry OBJECT-TYPE SYNTAX TeLinkOspfTeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "If OSPF is enabled, an entry in this table is created for every TE link." AUGMENTS { teLinkEntry } ::= { teLinkOspfTeTable 1 } TeLinkOspfTeEntry ::= SEQUENCE { teLinkOspfLinkType INTEGER, teLinkOspfLinkId RouterID } teLinkOspfLinkType OBJECT-TYPE SYNTAX INTEGER { pointToPoint(1), multiAccess(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the OSPF link type for the TE link. All TE links within the same bundle must have the same link type." ::= { teLinkOspfTeEntry 1 } teLinkOspfLinkId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-create STATUS current DESCRIPTION "On point-to-point link, the link identifier is the Router ID of the neighbor. For bundled link, is derived from the link identifier associated with its TE links." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkOspfTeEntry 2 } -- End of teLinkOspfTeTable -- TE Link Shared Risk Link Group Table teLinkSrlgTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the SRLGs associated with TE links." ::= { linkBundlingObjects 4 } teLinkSrlgEntry OBJECT-TYPE SYNTAX TeLinkSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about a SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkSrlgTable that use the ifIndex of this TE link." INDEX { ifIndex, srlg } ::= { teLinkSrlgTable 1 } TeLinkSrlgEntry ::= SEQUENCE { srlg Unsigned32, srlgRowStatus RowStatus, srlgStorageType StorageType } srlg OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This identifies a SRLG supported by the TE link." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkSrlgEntry 1 } srlgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when srlgRowStatus is active." ::= { teLinkSrlgEntry 2 } srlgStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkSrlgEntry 3 } -- End of teLinkSrlgTable -- TE Link Bandwidth Table teLinkBandwidthTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the priority-based bandwidth table for TE links." ::= { linkBundlingObjects 5 } teLinkBandwidthEntry OBJECT-TYPE SYNTAX TeLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about the priority-based bandwidth of TE links. An ifEntry in the ifTable must exist before a teLinkBandwidthEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkBandwidthTable that use the ifIndex of this TE link." INDEX { ifIndex, teLinkPriority } ::= { teLinkBandwidthTable 1 } TeLinkBandwidthEntry ::= SEQUENCE { teLinkPriority Unsigned32, teLinkUnreservedBandwidth Unsigned32, teLinkMaximumLspBandwidth Unsigned32, teLinkBandwidthRowStatus RowStatus, teLinkBandwidthStorageType StorageType } teLinkPriority OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute specifies the priority. It should be mapped to a number between 0 and 7" REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { teLinkBandwidthEntry 1 } teLinkUnreservedBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkBandwidthEntry 2 } teLinkMaximumLspBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link maximum LSP bandwidth at priority p. It is the maximum of all maximum LSP bandwidth at priority p of the component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-mpls-bundle-03.txt - Link Bundling in MPLS Traffic Engineering, K. Kompella, Y. Rekhter, L. Berger, May 2002." ::= { teLinkBandwidthEntry 3 } teLinkBandwidthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkBandwidthRowStatus is active." ::= { teLinkBandwidthEntry 4 } teLinkBandwidthStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkBandwidthEntry 5 } -- End of teLinkBandwidthTable -- Component Link Table componentLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the component link parameters." ::= { linkBundlingObjects 6 } componentLinkEntry OBJECT-TYPE SYNTAX ComponentLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table exists for each ifEntry that represents a component link. An ifEntry must exist in the ifTable before a componentLinkEntry is created with the corresponding ifIndex. If an entry representing a component link is destroyed in the ifTable, then so is the corresponding entry in the componentLinkTable. The administrative and operational status values are controlled from the ifEntry." INDEX { ifIndex } ::= { componentLinkTable 1 } ComponentLinkEntry ::= SEQUENCE { componentLinkMuxCapability INTEGER, componentLinkPreferredProtection INTEGER, componentLinkCurrentProtection INTEGER, componentLinkRowStatus RowStatus, componentLinkStorageType StorageType } componentLinkMuxCapability OBJECT-TYPE SYNTAX INTEGER { packetSwitch1(1), packetSwitch2(2), packetSwitch3(3), packetSwitch4(4), layer2Switch(51), tdm(100), lambdaSwitch(150), fiberSwitch(200) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link multiplexing capabilities of the component link." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkEntry 1 } componentLinkPreferredProtection OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies whether this component link is a primary or secondary entity." ::= { componentLinkEntry 2 } componentLinkCurrentProtection OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies whether this component link is currently used as primary or secondary link." ::= { componentLinkEntry 3 } componentLinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkRowStatus is active." ::= { componentLinkEntry 4 } componentLinkStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkEntry 5 } -- End of componentLinkTable -- Component Link Descriptor Table componentLinkDescriptorTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the link descriptors associated with the component links." ::= { linkBundlingObjects 7 } componentLinkDescriptorEntry OBJECT-TYPE SYNTAX ComponentLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created for every component link descriptor. An ifEntry in the ifTable must exist before a componentLinkDescriptorEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkDescriptorTable that use the ifIndex of this component link." INDEX { ifIndex, componentLinkDescrId } ::= { componentLinkDescriptorTable 1 } ComponentLinkDescriptorEntry ::= SEQUENCE { componentLinkDescrId Unsigned32, componentLinkEncodingType INTEGER, componentLinkDescrPriority Unsigned32, componentLinkMinReservBandwidth Unsigned32, componentLinkMaxReservBandwidth Unsigned32, componentLinkDescrRowStatus RowStatus, componentLinkDescrStorageType StorageType } componentLinkDescrId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the link descriptor identifier." ::= { componentLinkDescriptorEntry 1 } componentLinkEncodingType OBJECT-TYPE SYNTAX INTEGER { packet(1), ethernet(2), ansiEtsiPdh(3), sdhItuSonetAnsi(5), digitalWrapper(7), lambda(8), fiber(9), fiberChannel(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the component link encoding type." REFERENCE "draft-ietf-mpls-generalized-signaling-08.txt - Generalized MPLS Signaling Functional Description, P. Ashwood-Smith, A. Banarjee, L. Berger, G. Bernstein, J. Drake, Y. Fan, E. Mannie, J. Lang, B. Rajagopalan, Y. Rekhter, D. Saha, V. Sharma, G. Swallow, Z. Tang, April 2002." ::= { componentLinkDescriptorEntry 2 } componentLinkDescrPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the lowest priority at which that link encoding type is available for the component link." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkDescriptorEntry 3 } componentLinkMinReservBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the minimum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkDescriptorEntry 4 } componentLinkMaxReservBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the maximum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkDescriptorEntry 5 } componentLinkDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkDescrRowStatus is active." ::= { componentLinkDescriptorEntry 6 } componentLinkDescrStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkDescriptorEntry 7 } -- End of componentLinkDescriptorTable -- Component Link Bandwidth Table componentLinkBandwidthTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the priority-based bandwidth for component links." ::= { linkBundlingObjects 8 } componentLinkBandwidthEntry OBJECT-TYPE SYNTAX ComponentLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about the priority-based bandwidth on component links. An ifEntry in the ifTable must exist before a componentLinkBandwidthEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkBandwidthTable that use the ifIndex of this component link." INDEX { ifIndex, componentLinkPriority } ::= { componentLinkBandwidthTable 1 } ComponentLinkBandwidthEntry ::= SEQUENCE { componentLinkPriority Unsigned32, componentLinkUnreservedBandwidth Unsigned32, componentLinkMaximumLspBandwidth Unsigned32, componentLinkBandwidthRowStatus RowStatus, componentLinkBwStorageType StorageType } componentLinkPriority OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute specifies the priority. It should be mapped to a number between 0 and 7." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkBandwidthEntry 1 } componentLinkUnreservedBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies the component link unreserved bandwidth at priority p. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkBandwidthEntry 2 } componentLinkMaximumLspBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the component link maximum LSP bandwidth at priority p. This value is an estimate in units of 1,000 bits per second." REFERENCE "draft-ietf-ccamp-ospf-gmpls-extensions-07.txt - OSPF Extensions in Support of Generalized MPLS, K. Kompella, Y. Rekhter, A. Banerjee, J. Drake, G. Bernstein, D. Fedyk, E. Mannie, D. Saha, V. Sharma, May 2002." ::= { componentLinkBandwidthEntry 3 } componentLinkBandwidthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkBandwidthRowStatus is active." ::= { componentLinkBandwidthEntry 4 } componentLinkBwStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkBandwidthEntry 5 } -- End of componentLinkBandwidthTable -- Notification Configuration linkBundlingNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of the link bundling notifications, otherwise these notifications are not emitted." DEFVAL { false } ::= { linkBundlingObjects 9 } -- Notifications -- Bundled Link Notifications linkBundleMismatch NOTIFICATION-TYPE OBJECTS { teLinkIpAddrType, teLinkIpAddr, teLinkRemoteIpAddr } STATUS current DESCRIPTION "This notification is generated when a mismatch is found on a bundled link. Such mismatch can be detected for instance if one of the traffic engineering parameters is not consistent across all TE links within a bundled link (resource class, OSPF link type, etc.)." ::= { linkBundlingNotifications 1 } -- End of notifications -- Module compliance linkBundlingGroups OBJECT IDENTIFIER ::= { linkBundlingConformance 1 } linkBundlingCompliances OBJECT IDENTIFIER ::= { linkBundlingConformance 2 } linkBundlingFullModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the configuration and monitoring of link bundling MIB." MODULE -- this module -- The mandatory groups have to be implemented -- by all devices supporting link bundling. However, they may all -- be supported as read-only objects in the case where automatic -- configuration is supported. MANDATORY-GROUPS { linkBundlingGroup, teLinkBandwidthGroup, componentLinkBandwidthGroup } GROUP teLinkOspfTeGroup DESCRIPTION "This group is mandatory for OSPF enabled devices." GROUP teLinkSrlgGroup DESCRIPTION "This group is mandatory for G-MPLS enabled devices." GROUP linkBundlingNotificationGroup DESCRIPTION "This group is mandatory for equipment that support link bundling notifications." -- teLinkTable OBJECT teLinkIpAddrType SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "The dns(16) address type need not be supported. The ipv4(1) and ipv6(2) address types need not be supported if numbered links are not supported. The unknown(0) address type need not be supported if unnumbered links are not supported." OBJECT teLinkIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkRemoteIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkProtectionType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkDescriptorTable OBJECT teLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMinReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMaxReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkDescrStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkOspfTeTable OBJECT teLinkOspfLinkType SYNTAX INTEGER { pointToPoint(1) } MIN-ACCESS read-only DESCRIPTION "A value of multiAccess(2) need not be supported." OBJECT teLinkOspfLinkId MIN-ACCESS read-only DESCRIPTION "Write access is not required." -- teLinkSrlgTable OBJECT srlgRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT srlgStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkBandwidthTable OBJECT teLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT teLinkBandwidthStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkTable OBJECT componentLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMaxReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkDescriptorTable OBJECT componentLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT componentLinkDescrStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkBandwidthTable OBJECT componentLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkBwStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." ::= { linkBundlingCompliances 1 } linkBundlingMonModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the monitoring of link bundling MIB." MODULE -- this module -- The mandatory groups have to be implemented -- by all devices supporting link bundling. However, they may all -- be supported as read-only objects in the case where manual -- configuration is unsupported. MANDATORY-GROUPS { linkBundlingGroup, teLinkBandwidthGroup, componentLinkBandwidthGroup } GROUP teLinkOspfTeGroup DESCRIPTION "This group is mandatory for OSPF enabled devices." GROUP teLinkSrlgGroup DESCRIPTION "This group is mandatory for G-MPLS enabled devices." GROUP linkBundlingNotificationGroup DESCRIPTION "This group is optional." -- teLinkTable OBJECT teLinkIpAddrType SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "The dns(16) address type need not be supported. The ipv4(1) and ipv6(2) address types need not be supported if numbered links are not supported. The unknown(0) address type need not be supported if unnumbered links are not supported." OBJECT teLinkIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkRemoteIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkProtectionType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkWorkingPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkFlooding MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkDescriptorTable OBJECT teLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMinReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMaxReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkDescrStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkOspfTeTable OBJECT teLinkOspfLinkType SYNTAX INTEGER { pointToPoint(1) } DESCRIPTION "A value of multiAccess(2) need not be supported." OBJECT teLinkOspfLinkId MIN-ACCESS read-only DESCRIPTION "Write access is not required." -- teLinkSrlgTable OBJECT srlgRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT srlgStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkBandwidthTable OBJECT teLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT teLinkBandwidthStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkTable OBJECT componentLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkPreferredProtection MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMaxReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkDescriptorTable OBJECT componentLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMinReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT componentLinkDescrStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkBandwidthTable OBJECT componentLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkBwStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." ::= { linkBundlingCompliances 2 } -- Units of conformance linkBundlingGroup OBJECT-GROUP OBJECTS { teLinkIpAddrType, teLinkIpAddr, teLinkRemoteIpAddr, teLinkMetric, teLinkMuxCapability, teLinkProtectionType, teLinkWorkingPriority, teLinkResourceClass, teLinkIncomingIfId, teLinkOutgoingIfId, teLinkFlooding, teLinkRowStatus, teLinkStorageType, teLinkEncodingType, teLinkDescrPriority, teLinkMinReservableBandwidth, teLinkMaxReservableBandwidth, teLinkDescrRowStatus, teLinkDescrStorageType, componentLinkMuxCapability, componentLinkPreferredProtection, componentLinkCurrentProtection, componentLinkRowStatus, componentLinkStorageType, linkBundlingNotifEnable } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of resources associated with TE links." ::= { linkBundlingGroups 1 } teLinkOspfTeGroup OBJECT-GROUP OBJECTS { teLinkOspfLinkType, teLinkOspfLinkId } STATUS current DESCRIPTION "Collection of objects needed for the OSPF traffic engineering parameters of TE links." ::= { linkBundlingGroups 2 } teLinkSrlgGroup OBJECT-GROUP OBJECTS { srlgRowStatus, srlgStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of SRLG resources associated with TE links." ::= { linkBundlingGroups 3 } teLinkBandwidthGroup OBJECT-GROUP OBJECTS { teLinkUnreservedBandwidth, teLinkMaximumLspBandwidth, teLinkBandwidthRowStatus, teLinkBandwidthStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of the priority-based bandwidth resources associated with TE links and component links." ::= { linkBundlingGroups 4 } componentLinkBandwidthGroup OBJECT-GROUP OBJECTS { componentLinkEncodingType, componentLinkDescrPriority, componentLinkMinReservBandwidth, componentLinkMaxReservBandwidth, componentLinkDescrRowStatus, componentLinkDescrStorageType, componentLinkUnreservedBandwidth, componentLinkMaximumLspBandwidth, componentLinkBandwidthRowStatus, componentLinkBwStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of bandwidth parameters associated with component links." ::= { linkBundlingGroups 5 } linkBundlingNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { linkBundleMismatch } STATUS current DESCRIPTION "Set of notifications implemented in this module. None is mandatory." ::= { linkBundlingGroups 6 } -- End of LINK-BUNDLING-MIB END -- -- -- Copyright (C) The Internet Society (2001). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this docu- -- ment itself may not be modified in any way, such as by removing the -- copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of develop- -- ing Internet standards in which case the procedures for copyrights -- defined in the Internet Standards process must be followed, or as -- required to translate it into languages other than English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. This -- document and the information contained herein is provided on an "AS -- IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK -- FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT -- LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL -- NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY -- OR FITNESS FOR A PARTICULAR PURPOSE.