-- extracted from draft-ietf-adslmib-adsl2-03.txt -- at Tue Oct 11 06:36:31 2005 NGDSL-LINE-TC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, transmission FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; ngdslTCMIB MODULE-IDENTITY LAST-UPDATED "200510090000Z" -- October 9, 2005 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-Chair: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 Co-editor: Moti Morgenstern ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: moti.morgenstern@ecitele.com Phone: +972 3 926 6258 Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 Hasivim St. Petach Tikva 49517, Israel. Email: mbdodge@ieee.org Phone: +972 3 926 8421 Co-editor: Scott Baillie NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: scott.baillie@nec.com.au Phone: +61 3 9264 3986 Co-editor: Umberto Bonollo NEC Australia Postal: 649-655 Springvale Road, Mulgrave, Victoria 3170, Australia. Email: umberto.bonollo@nec.com.au Phone: +61 3 9264 3385 " DESCRIPTION "This MIB Module provides Textual Conventions to be used by the NGDSL-LINE-MIB module for the purpose of managing ADSL, ADSL2 and ADSL2+ lines. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices." -- RFC Ed.: replace XXXX with assigned number & remove this note REVISION "200510090000Z" -- October 09, 2005 DESCRIPTION "Initial version, published as RFC XXXX." -- RFC Ed.: replace XX with assigned number & remove this note ::= { transmission xxx } -- RFC Ed.: we suggest to put it under { transmission 230 } because -- this is the first available number. ------------------------------------------------ -- Textual Conventions -- ------------------------------------------------ Adsl2Unit ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies a transceiver as being either atuc or atur. An ADSL line consists of two transceivers, an atuc and an atur. Attributes with this syntax reference the two sides of a line. Specified as an INTEGER, the two values are: atuc(1) -- central site transceiver atur(2) -- remote site transceiver" SYNTAX INTEGER { atuc(1), atur(2) } Adsl2Direction ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Identifies the direction of a band as being either upstream or downstream. Specified as an INTEGER, the two values are: upstream(1) downstream(2)" SYNTAX INTEGER { upstream(1), downstream(2) } Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A set of ADSL2 line transmission modes, with one bit per mode. The notes (F) and (L) denote Full-Rate and Lite/splitterless respectively: Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 02 : G.992.1 POTS non-overlapped (F) Bit 03 : G.992.1 POTS overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 08 : G.992.2 POTS non-overlapped (L) Bit 09 : G.992.2 POTS overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1 Bit 13-17: Reserved Bit 18 : G.992.3 POTS non-overlapped (F) Bit 19 : G.992.3 POTS overlapped (F) Bit 20 : G.992.3 ISDN non-overlapped (F) Bit 21 : G.992.3 ISDN overlapped (F) Bit 22-23: Reserved Bit 24 : G.992.4 POTS non-overlapped (L) Bit 25 : G.992.4 POTS overlapped (L) Bit 26-27: Reserved Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F) Bit 29 : G.992.3 Annex I All-Digital overlapped (F) Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F) Bit 31 : G.992.3 Annex J All-Digital overlapped (F) Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L) Bit 33 : G.992.4 Annex I All-Digital overlapped (L) Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1, wide U/S (F) Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2, narrow U/S(F) Bit 36 : G.992.3 Annex L POTS overlapped, mode 3, wide U/S (F) Bit 37 : G.992.3 Annex L POTS overlapped, mode 4, narrow U/S (F) Bit 38 : G.992.3 Annex M POTS non-overlapped (F) Bit 39 : G.992.3 Annex M POTS overlapped (F) Bit 40 : G.992.5 POTS non-overlapped (F) Bit 41 : G.992.5 POTS overlapped (F) Bit 42 : G.992.5 ISDN non-overlapped (F) Bit 43 : G.992.5 ISDN overlapped (F) Bit 44-45: Reserved Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F) Bit 47 : G.992.5 Annex I All-Digital overlapped (F) Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F) Bit 49 : G.992.5 Annex J All-Digital overlapped (F) Bit 50 : G.992.5 Annex M POTS non-overlapped (F) Bit 51 : G.992.5 Annex M POTS overlapped (F) Bit 52-55: Reserved" SYNTAX BITS { ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921isdnOverlapped(5), q9921tcmIsdnNonOverlapped(6), q9921tcmIsdnOverlapped(7), q9922potsNonOverlapeed(8), q9922potsOverlapped(9), q9922tcmIsdnNonOverlapped(10), q9922tcmIsdnOverlapped(11), q9921tcmIsdnSymmetric(12), reserved1(13), reserved2(14), reserved3(15), reserved4(16), reserved5(17), q9923PotsNonOverlapped(18), q9923PotsOverlapped(19), q9923IsdnNonOverlapped(20), q9923isdnOverlapped(21), reserved6(22), reserved7(23), q9924potsNonOverlapeed(24), q9924potsOverlapped(25), reserved8(26), reserved9(27), q9923AnnexIAllDigNonOverlapped(28), q9923AnnexIAllDigOverlapped(29), q9923AnnexJAllDigNonOverlapped(30), q9923AnnexJAllDigOverlapped(31), q9924AnnexIAllDigNonOverlapped(32), q9924AnnexIAllDigOverlapped(33), q9923AnnexLMode1NonOverlapped(34), q9923AnnexLMode2NonOverlapped(35), q9923AnnexLMode3Overlapped(36), q9923AnnexLMode4Overlapped(37), q9923AnnexMPotsNonOverlapped(38), q9923AnnexMPotsOverlapped(39), q9925PotsNonOverlapped(40), q9925PotsOverlapped(41), q9925IsdnNonOverlapped(42), q9925isdnOverlapped(43), reserved10(44), reserved11(45), q9925AnnexIAllDigNonOverlapped(46), q9925AnnexIAllDigOverlapped(47), q9925AnnexJAllDigNonOverlapped(48), q9925AnnexJAllDigOverlapped(49), q9925AnnexMPotsNonOverlapped(50), q9925AnnexMPotsOverlapped(51), reserved12(52), reserved13(53), reserved14(54), reserved15(55) } Adsl2RaMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the rate adaptation behavior for the line. The three possible behaviors are: manual (1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate. rainit (2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values. dynamicRa (3)- Dynamic Rate-Adaptation during initialization process as well as during SHOWTIME" SYNTAX INTEGER { manual(1), raInit(2), dynamicRa(3) } Adsl2InitResult ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the result of full initialization attempt, the six possible result values are: noFail (0) - Successful initialization configError (1) - Configuration failure configNotFeasible (2) - Configuration details not supported commFail (3) - Communication failure noPeerAtu (4) - Peer ATU not detected otherCause (5) - Other initialization failure reason" SYNTAX INTEGER { noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5) } Adsl2OperationModes ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The ADSL2 management model specified includes an ADSL Mode attribute which identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. " SYNTAX INTEGER { defMode (1), adsl (2), adsl2Pots (3), adsl2Isdn (4), adsl2PlusPots (5), adsl2PlusIsdn (6), adsl2ReachExtended (7) } Adsl2PowerMngState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax uniquely identify each power management state defined for the ADSL/ADSL2 or ADSL2+ link. The possible values are: l0(0) - L0 - Full power management state l1(1) - L1 - Low power management state (for G.992.2) l2(2) - L2 - Low power management state (for G.992.3, G.992.4, and G.992.5) l3(3) - L3 - Idle power management state" SYNTAX INTEGER { l0(0), l1(1), l2(2), l3(3) } Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the desired power management state for the ADSL/ADSL2 or ADSL2+ link: l3toL0 (1) - Perform a transition from L3 to L0 (Full power management state) l0toL2 (2) - Perform a transition from L0 to L2 (Low power management state) l0orL2toL3 (3) - Perform a transition into L3 (Idle power management state)" SYNTAX INTEGER { l3toL0 (0), l0toL2 (2), l0orL2toL3 (3) } Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the power modes/states into which the ATU-C or ATU-R may autonomously transit. It is a BITS structure that allows controlling the following transit options: allowTransitionsToIdle (0) - xTU may autonomously transit to idle (L3) state. allowTransitionsToLowPower (1)- xTU may autonomously transit to low-power (L2) state." SYNTAX BITS { allowTransitionsToIdle(0), allowTransitionsToLowPower(1) } Adsl2LineLdsf ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ link. The possible values are: inhibit (0) - Inhibit Loop Diagnostic mode force (1) - Force/Initiate Loop Diagnostic mode" SYNTAX INTEGER { inhibit(0), force(1) } Adsl2LdsfResult ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Possible failure reasons associated with performing Dual Ended Loop Test (DELT) on a DSL line. Possible values are: none (1) - The default value in case LDSF was never requested for the associated line. success (2) - The recent command completed successfully. inProgress (3) - The Loop Diagnostics process is in progress. unsupported (4) - The NE or the line card doesn't support LDSF. cannotRun (5) - The NE cannot initiate the command, due to a non specific reason. aborted (6) - The Loop Diagnostics process aborted. failed (7) - The Loop Diagnostics process failed. illegalMode (8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp (9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull (10)- The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources (11)- The NE cannot initiate the command, due to lack of internal memory resources." SYNTAX INTEGER { none (1), success (2), inProgress (3), unsupported (4), cannotRun (5), aborted (6), failed (7), illegalMode (8), adminUp (9), tableFull (10), noResources (11) } Adsl2SymbolProtection ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the minimum length impulse noise protection (INP) in terms of number of symbols. The possible values are: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol" SYNTAX INTEGER { noProtection (1), halfSymbol (2), singleSymbol (3), twoSymbols (4), threeSymbols (5), fourSymbols (6), fiveSymbols (7), sixSymbols (8), sevenSymbols (9), eightSymbols (10), nineSymbols (11), tenSymbols (12), elevenSymbols (13), twelveSymbols (14), thirteeSymbols (15), fourteenSymbols (16), fifteenSymbols (17), sixteenSymbols (18) } Adsl2MaxBer ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are configuration parameters that reference the maximum Bit Error Rate (BER). The possible values are: eminus3 (1) - Maximum BER=E^-3 eminus5 (2) - Maximum BER=E^-5 eminus7 (3) - Maximum BER=E^-7" SYNTAX INTEGER { eminus3(1), eminus5(2), eminus7(3) } Adsl2ScMaskDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is not in use." SYNTAX OCTET STRING (SIZE(0..64)) Adsl2ScMaskUs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 64 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is not in use." SYNTAX OCTET STRING (SIZE(0..8)) Adsl2RfiDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each one of the 512 bits in this OCTET STRING array represents the corresponding bin in the downstream direction. A value of one indicates that the bin is part of a notch filter." SYNTAX OCTET STRING (SIZE(0..64)) Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 32 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5dBm/Hz." SYNTAX OCTET STRING (SIZE(0..96)) Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 4 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0dBm/Hz) to 255 (-127.5 dBm/Hz) using units of 0.5dBm/Hz." SYNTAX OCTET STRING (SIZE(0..12)) Adsl2Tssi ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This is a structure that represents up to 32 transmit spectrum shaping (TSSi) breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the shaping parameter at the breakpoint. It is a value from 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted." SYNTAX OCTET STRING (SIZE(0..96)) Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This parameter represents the last successful transmitted initialization state in the last full initialization performed on the line." SYNTAX INTEGER { atucG9941(0), atucQuiet1(1), atucComb1(2), atucQuiet2(3), atucComb2(4), atucIcomb1(5), atucLineprob(6), atucQuiet3(7), atucComb3(8), atucIComb2(9), atucMsgfmt(10), atucMsgpcb(11), atucQuiet4(12), atucReverb1(13), atucTref1(14), atucReverb2(15), atucEct(16), atucReverb3(17), atucTref2(18), atucReverb4(19), atucSegue1(20), atucMsg1(21), atucReverb5(22), atucSegue2(23), atucMedley(24), atucExchmarker(25), atucMsg2(26), atucReverb6(27), atucSegue3(28), atucParams(29), atucReverb7(30), atucSegue4(31), atucShowtime(32), -- aturG9941(100), aturQuiet1(101), aturComb1(102), aturQuiet2(103), aturComb2(104), aturIcomb1(105), aturLineprob(106), aturQuiet3(107), aturComb3(108), aturIcomb2(109), aturMsgfmt(110), aturMsgpcb(111), aturReverb1(112), aturQuiet4(113), aturReverb2(114), aturQuiet5(115), aturReverb3(116), aturEct(117), aturReverb4(118), aturSegue1(119), aturReverb5(120), aturSegue2(121), aturMsg1(122), aturMedley(123), aturExchmarker(124), aturMsg2(125), aturReverb6(126), aturSegue3(127), aturParams(128), aturReverb7(129), aturSegue4(130), aturShowtime(131) } Adsl2LineStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link. This BITS structure can report the following failures: noDefect (0) - This bit position positively reports that no defect or failure exist. lossOfFraming (1) - Loss of frame synchronization lossOfSignal (2) - Loss of signal lossOfPower (3) - Loss of power. Usually this failure may be reported for CPE units only initFailure (4) - Recent initialization process failed." SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), initFailure(4) } Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for Transmission Convergence (TC) layer of a given ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect (0) - This bit position positively reports that no defect or failure exist. noCellDelineation (1) - Cell delineation never acquired on the associated ATM data path since the link successfully initialized. lossOfCellDelineation (2)- Loss of cell delineation on the associated ATM data path" SYNTAX BITS { noDefect(0), noCellDelineation(1), lossOfCellDelineation(2) } Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Attributes with this syntax are status parameters that reflect the failure status for a given PTM interface (packet data path over an ADSL/ADSL2 or ADSL2+ link). This BITS structure can report the following failures: noDefect (0) - This bit position positively reports that no defect or failure exist. outOfSync (1) - Out of synchronization. " SYNTAX BITS { noDefect(0), outOfSync(1) } END -- -- Copyright (C) The Internet Society (2005). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- -- Acknowledgment -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society.