-- extracted from draft-ietf-ospf-ospfv3-mib-03.txt -- at Tue Dec 5 10:05:27 2000 OSPFV3-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, experimental, Counter32, Gauge32, Integer32, IpAddress FROM SNMPv2-SMI TruthValue, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF Ipv6IfIndex, Ipv6Address, Ipv6AddressPrefix FROM IPV6-TC AreaID, RouterID, Metric, BigMetric, Status, PositiveInteger, HelloRange, UpToMaxAge, DesignatedRouterPriority FROM OSPF-MIB ; ospfv3MIB MODULE-IDENTITY LAST-UPDATED "200011161305Z" ORGANIZATION "IETF OSPF Working Group" CONTACT-INFO " WG e-mail: ospf@discuss.microsoft.com Dan Joyal Postal: Quantum Bridge Communications 2 Tech Park Andover, MA 01810 USA Tel: +1-978-688-9100 E-Mail: djoyal@quantumbridge.com" DESCRIPTION "The MIB module to describe the OSPF Version for IPv6" ::= { experimental 102 } --mib-2 OID to be assigned ospfv3 OBJECT IDENTIFIER ::= { ospfv3MIB 1 } -- OSPFv3 General Variables -- These parameters apply globally to the Router's -- OSPFv3 Process. ospfv3GeneralGroup OBJECT IDENTIFIER ::= { ospfv3 1 } Internet Draft Expires May 2001 4 OSPFv3 MIB November 2000 ospfv3RouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-write STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IPv4 interface addresses if IPv4 is configured." ::= { ospfv3GeneralGroup 1 } ospfv3AdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one inter- face; 'disabled' disables it on all inter- faces." ::= { ospfv3GeneralGroup 2 } ospfv3VersionNumber OBJECT-TYPE SYNTAX INTEGER { version3 (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version number of OSPF for IPv6 is 3." ::= { ospfv3GeneralGroup 3 } ospfv3AreaBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A flag to note whether this router is an area border router." REFERENCE "OSPF Version 2, Section 3 Splitting the AS into Areas" ::= { ospfv3GeneralGroup 4 } ospfv3ASBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write Internet Draft Expires May 2001 5 OSPFv3 MIB November 2000 STATUS current DESCRIPTION "A flag to note whether this router is config- ured as an Autonomous System border router." REFERENCE "OSPF Version 2, Section 3.3 Classification of routers" ::= { ospfv3GeneralGroup 5 } ospfv3AsScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of AS-Scope (e.g. AS-External) link-state advertisements in the link-state database." ::= { ospfv3GeneralGroup 6 } ospfv3AsScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the LS checksums of the AS-scoped link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." ::= { ospfv3GeneralGroup 7 } ospfv3OriginateNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA." ::= { ospfv3GeneralGroup 8 } ospfv3RxNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of link-state advertisements re- Internet Draft Expires May 2001 6 OSPFv3 MIB November 2000 ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments." ::= { ospfv3GeneralGroup 9 } ospfv3ExtAreaLsdbLimit OBJECT-TYPE SYNTAX Integer32 (-1..'7FFFFFFF'h) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow- State. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. OspfExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded)." DEFVAL { -1 } ::= { ospfv3GeneralGroup 10 } ospfv3MulticastExtensions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IPv6 multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are Internet Draft Expires May 2001 7 OSPFv3 MIB November 2000 allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled." DEFVAL { 0 } ::= { ospfv3GeneralGroup 11 } ospfv3ExitOverflowInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-External-LSAs. When set to 0, the router will not leave Overflow- State until restarted." DEFVAL { 0 } ::= { ospfv3GeneralGroup 12 } ospfv3DemandExtensions OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The router's support for demand routing." REFERENCE "OSPF Version 2, Appendix on Demand Routing" ::= { ospfv3GeneralGroup 13 } ospfv3TrafficEngineeringSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The router's support for traffic engineering extensions." ::= { ospfv3GeneralGroup 14 } -- The OSPFv3 Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area ospfv3AreaTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3AreaEntry MAX-ACCESS not-accessible STATUS current Internet Draft Expires May 2001 8 OSPFv3 MIB November 2000 DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of the router's attached areas." REFERENCE "OSPF Version 2, Section 6 The Area Data Struc- ture" ::= { ospfv3 2 } ospfv3AreaEntry OBJECT-TYPE SYNTAX Ospfv3AreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas." INDEX { ospfv3AreaId } ::= { ospfv3AreaTable 1 } Ospfv3AreaEntry ::= SEQUENCE { ospfv3AreaId AreaID, ospfv3ImportAsExtern INTEGER, ospfv3SpfRuns Counter32, ospfv3AreaBdrRtrCount Gauge32, ospfv3AsBdrRtrCount Gauge32, ospfv3AreaScopeLsaCount Gauge32, ospfv3AreaScopeLsaCksumSum Integer32, ospfv3AreaSummary INTEGER, ospfv3AreaStatus RowStatus, ospfv3StubMetric BigMetric, ospfv3AreaNssaTranslatorRole INTEGER, ospfv3AreaNssaTranslatorState INTEGER, ospfv3AreaNssaTranslatorStabilityInterval PositiveInteger, ospfv3AreaNssaTranslatorEvents Counter32 } Internet Draft Expires May 2001 9 OSPFv3 MIB November 2000 ospfv3AreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPFv3 backbone." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3AreaEntry 1 } ospfv3ImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), -- normal area importNoExternal (2), -- stub area importNssa (3) -- not-so-stubby-area } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as Type-7 LSAs which have Area-scope" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { ospfv3AreaEntry 2 } ospfv3SpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm." ::= { ospfv3AreaEntry 3 } ospfv3AreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass." ::= { ospfv3AreaEntry 4 } Internet Draft Expires May 2001 10 OSPFv3 MIB November 2000 ospfv3AsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { ospfv3AreaEntry 5 } ospfv3AreaScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Area-Scope link-state advertisements in this area's link-state database." ::= { ospfv3AreaEntry 6 } ospfv3AreaScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the Area-Scope link-state advertisements' LS checksums contained in this area's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { ospfv3AreaEntry 7 } ospfv3AreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable ospfv3AreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- Internet Draft Expires May 2001 11 OSPFv3 MIB November 2000 fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { noAreaSummary } ::= { ospfv3AreaEntry 8 } ospfv3AreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfv3AreaEntry 9 } ospfv3StubMetric OBJECT-TYPE SYNTAX BigMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The metric value advertised for the default route into Stub and NSSA areas." ::= { ospfv3AreaEntry 10 } ospfv3AreaNssaTranslatorRole OBJECT-TYPE SYNTAX INTEGER { always (1), candidate (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates an NSSA Border router's ability to perform NSSA translation of type-7 LSAs into type-5 LSAs." DEFVAL { candidate } ::= { ospfv3AreaEntry 11 } ospfv3AreaNssaTranslatorState OBJECT-TYPE SYNTAX INTEGER { enabled (1), elected (2), disabled (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if and how an NSSA Border router is performing NSSA translation of type-7 LSAs into type-5 LSAs. When this object set to enabled, the NSSA Border router's OspfAreaNssaExtTranslatorRole has been set to Internet Draft Expires May 2001 12 OSPFv3 MIB November 2000 always. When this object is set to elected, a candidate NSSA Border router is Translating type-7 LSAs into type-5. When this object is set to disabled, a candidate NSSA Border router is NOT translating type-7 LSAs into type-5." ::= { ospfv3AreaEntry 12 } ospfv3AreaNssaTranslatorStabilityInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties." DEFVAL { 40 } ::= { ospfv3AreaEntry 13 } ospfv3AreaNssaTranslatorEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of Translator State changes that have occurred since the last boot-up." ::= { ospfv3AreaEntry 14 } -- OSPFv3 AS-Scope Link State Database -- The Link State Database contains the AS-Scope Link State -- Advertisements from throughout the areas that the -- device is attached to. ospfv3AsLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3AsLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPFv3 Process's AS-Scope Link State Database." ::= { ospfv3 3 } ospfv3AsLsdbEntry OBJECT-TYPE SYNTAX Ospfv3AsLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single AS-Scope Link State Advertisement." INDEX { ospfv3AsLsdbType, ospfv3AsLsdbRouterId, Internet Draft Expires May 2001 13 OSPFv3 MIB November 2000 ospfv3AsLsdbLsid } ::= { ospfv3AsLsdbTable 1 } Ospfv3AsLsdbEntry ::= SEQUENCE { ospfv3AsLsdbType INTEGER, ospfv3AsLsdbRouterId RouterID, ospfv3AsLsdbLsid IpAddress, ospfv3AsLsdbSequence Integer32, ospfv3AsLsdbAge Integer32, ospfv3AsLsdbChecksum Integer32, ospfv3AsLsdbAdvertisement OCTET STRING } ospfv3AsLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (16389) -- 0x4005 } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized AS-Scope LSAs with the U-bit set are also store in this database." ::= { ospfv3AsLsdbEntry 1 } ospfv3AsLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfv3AsLsdbEntry 2 } ospfv3AsLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION Internet Draft Expires May 2001 14 OSPFv3 MIB November 2000 "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { ospfv3AsLsdbEntry 3 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. ospfv3AsLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfv3AsLsdbEntry 4 } ospfv3AsLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfv3AsLsdbEntry 5 } ospfv3AsLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum Internet Draft Expires May 2001 15 OSPFv3 MIB November 2000 used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfv3AsLsdbEntry 6 } ospfv3AsLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." ::= { ospfv3AsLsdbEntry 7 } -- OSPFv3 Area-Scope Link State Database -- The Link State Database contains the Area-Scope Link State -- Advertisements from throughout the area that the -- device is attached to. ospfv3AreaLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3AreaLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPFv3 Process's Area-Scope Link State Database." ::= { ospfv3 4 } ospfv3AreaLsdbEntry OBJECT-TYPE SYNTAX Ospfv3AreaLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Area-Scope Link State Advertisement." INDEX { ospfv3AreaLsdbAreaId, ospfv3AreaLsdbType, ospfv3AreaLsdbRouterId, ospfv3AreaLsdbLsid } ::= { ospfv3AreaLsdbTable 1 } Ospfv3AreaLsdbEntry ::= SEQUENCE { ospfv3AreaLsdbAreaId AreaID, ospfv3AreaLsdbType INTEGER, ospfv3AreaLsdbRouterId Internet Draft Expires May 2001 16 OSPFv3 MIB November 2000 RouterID, ospfv3AreaLsdbLsid IpAddress, ospfv3AreaLsdbSequence Integer32, ospfv3AreaLsdbAge Integer32, ospfv3AreaLsdbChecksum Integer32, ospfv3AreaLsdbAdvertisement OCTET STRING } ospfv3AreaLsdbAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION ôThe 32 bit identifier of the Area from which the LSA was received.ö REFERENCE ôOSPF Version 2, Appendix C.2 Area parametersö ::= { ospfv3AreaLsdbEntry 1 } ospfv3AreaLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLsa (8193), -- 0x2001 networkLsa (8194), -- 0x2002 interAreaPrefixLsa (8195), -- 0x2003 interAreaRouterLsa (8196), -- 0x2004 groupMembershipLsa (8198), -- 0x2006 nssaExternalLsa (8199), -- 0x2007 intraAreaPrefixLsa (8201) -- 0x2009 } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized Area-Scope LSAs with the U-bit set are also stored in this database." ::= { ospfv3AreaLsdbEntry 2 } ospfv3AreaLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE Internet Draft Expires May 2001 17 OSPFv3 MIB November 2000 "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfv3AreaLsdbEntry 3 } ospfv3AreaLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { ospfv3AreaLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. ospfv3AreaLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfv3AreaLsdbEntry 5 } ospfv3AreaLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfv3AreaLsdbEntry 6 } ospfv3AreaLsdbChecksum OBJECT-TYPE SYNTAX Integer32 Internet Draft Expires May 2001 18 OSPFv3 MIB November 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfv3AreaLsdbEntry 7 } ospfv3AreaLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." ::= { ospfv3AreaLsdbEntry 8 } -- OSPFv3 Link-Scope Link State Database -- The Link State Database contains the Link-Scope Link State -- Advertisements from the links that the -- device is attached to. ospfv3LinkLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3LinkLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPFv3 Process's Link-Scope Link State Database." ::= { ospfv3 5 } ospfv3LinkLsdbEntry OBJECT-TYPE SYNTAX Ospfv3LinkLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link-Scope Link State Advertisement." INDEX { ospfv3LinkLsdbIfIndex, ospfv3LinkLsdbType, ospfv3LinkLsdbRouterId, ospfv3LinkLsdbLsid } ::= { ospfv3LinkLsdbTable 1 } Internet Draft Expires May 2001 19 OSPFv3 MIB November 2000 Ospfv3LinkLsdbEntry ::= SEQUENCE { ospfv3LinkLsdbIfIndex Ipv6IfIndex, ospfv3LinkLsdbType INTEGER, ospfv3LinkLsdbRouterId RouterID, ospfv3LinkLsdbLsid IpAddress, ospfv3LinkLsdbSequence Integer32, ospfv3LinkLsdbAge Integer32, ospfv3LinkLsdbChecksum Integer32, ospfv3LinkLsdbAdvertisement OCTET STRING } ospfv3LinkLsdbIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the link from which the LSA was received.ö REFERENCE ôOSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3LinkLsdbEntry 1 } ospfv3LinkLsdbType OBJECT-TYPE SYNTAX INTEGER { linkLsa (8) -- 0x0008 } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized Link-Scope LSAs with the U-bit set are also stored in this database." ::= { ospfv3LinkLsdbEntry 2 } ospfv3LinkLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the Internet Draft Expires May 2001 20 OSPFv3 MIB November 2000 originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfv3LinkLsdbEntry 3 } ospfv3LinkLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { ospfv3LinkLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. ospfv3LinkLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfv3LinkLsdbEntry 5 } ospfv3LinkLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfv3LinkLsdbEntry 6 } Internet Draft Expires May 2001 21 OSPFv3 MIB November 2000 ospfv3LinkLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfv3LinkLsdbEntry 7 } ospfv3LinkLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." ::= { ospfv3LinkLsdbEntry 8 } -- OSPF Host Table -- The Host/Metric Table indicates what hosts are directly -- attached to the Router, and what metrics and types of -- service should be advertised for them. ospfv3HostTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3HostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of Hosts, and their metrics, that the router will advertise as host routes." REFERENCE "OSPF Version 2, Appendix C.6 Host route param- eters" ::= { ospfv3 6 } ospfv3HostEntry OBJECT-TYPE SYNTAX Ospfv3HostEntry MAX-ACCESS not-accessible STATUS current Internet Draft Expires May 2001 22 OSPFv3 MIB November 2000 DESCRIPTION "A metric to be advertised when a given host is reachable." INDEX { ospfv3HostIpv6Address } ::= { ospfv3HostTable 1 } Ospfv3HostEntry ::= SEQUENCE { ospfv3HostIpv6Address Ipv6Address, ospfv3HostMetric Metric, ospfv3HostStatus RowStatus, ospfv3HostAreaID AreaID } ospfv3HostIpv6Address OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the Host. Must be a Global or Site-local address." REFERENCE "OSPF Version 2, Appendix C.6 Host route parame- ters" ::= { ospfv3HostEntry 1 } ospfv3HostMetric OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-create STATUS current DESCRIPTION "The Metric to be advertised." REFERENCE "OSPF Version 2, Appendix C.6 Host route parame- ters" ::= { ospfv3HostEntry 2 } ospfv3HostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." Internet Draft Expires May 2001 23 OSPFv3 MIB November 2000 ::= { ospfv3HostEntry 3 } ospfv3HostAreaID OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-create STATUS current DESCRIPTION "The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 in- terface is in, or 0.0.0.0" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3HostEntry 4 } -- OSPFv3 Interface Table ospfv3IfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPFv3 Interface Table describes the inter- faces from the viewpoint of OSPFv3." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { ospfv3 7 } ospfv3IfEntry OBJECT-TYPE SYNTAX Ospfv3IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPFv3 Interface Entry describes one inter- face from the viewpoint of OSPFv3." INDEX { ospfv3IfIndex } ::= { ospfv3IfTable 1 } Ospfv3IfEntry ::= SEQUENCE { ospfv3IfIndex Ipv6IfIndex, ospfv3IfAreaId AreaID, ospfv3IfType INTEGER, ospfv3IfAdminStat Status, ospfv3IfRtrPriority Internet Draft Expires May 2001 24 OSPFv3 MIB November 2000 DesignatedRouterPriority, ospfv3IfTransitDelay UpToMaxAge, ospfv3IfRetransInterval UpToMaxAge, ospfv3IfHelloInterval HelloRange, ospfv3IfRtrDeadInterval PositiveInteger, ospfv3IfPollInterval PositiveInteger, ospfv3IfState INTEGER, ospfv3IfDesignatedRouter RouterID, ospfv3IfBackupDesignatedRouter RouterID, ospfv3IfEvents Counter32, ospfv3IfStatus RowStatus, ospfv3IfMulticastForwarding INTEGER, ospfv3IfDemand TruthValue, ospfv3IfMetricValue Metric, ospfv3IfLinkScopeLsaCount Gauge32, ospfv3IfLinkLsaCksumSum Integer32, ospfv3IfInstId Integer32 } ospfv3IfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of this OSPFv3 interface. It corresponds to the interface index of the Ipv6 interface on which OSPFv3 is configured." ::= { ospfv3IfEntry 1 } ospfv3IfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-create STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the area Internet Draft Expires May 2001 25 OSPFv3 MIB November 2000 to which the interface connects. Area ID 0.0.0.0 is used for the OSPFv3 backbone." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfv3IfEntry 2 } ospfv3IfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPFv3 interface type." ::= { ospfv3IfEntry 3 } ospfv3IfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPFv3 interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3." DEFVAL { enabled } ::= { ospfv3IfEntry 4 } ospfv3IfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-create STATUS current DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { ospfv3IfEntry 5 } ospfv3IfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge Internet Draft Expires May 2001 26 OSPFv3 MIB November 2000 MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { ospfv3IfEntry 6 } ospfv3IfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets." DEFVAL { 5 } ::= { ospfv3IfEntry 7 } ospfv3IfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { ospfv3IfEntry 8 } ospfv3IfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { ospfv3IfEntry 9 } ospfv3IfPollInterval OBJECT-TYPE Internet Draft Expires May 2001 27 OSPFv3 MIB November 2000 SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." DEFVAL { 120 } ::= { ospfv3IfEntry 10 } ospfv3IfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Interface State." DEFVAL { down } ::= { ospfv3IfEntry 11 } ospfv3IfDesignatedRouter OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfv3IfEntry 12 } ospfv3IfBackupDesignatedRouter OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Backup Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfv3IfEntry 14 } ospfv3IfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only Internet Draft Expires May 2001 28 OSPFv3 MIB November 2000 STATUS current DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { ospfv3IfEntry 15 } ospfv3IfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfv3IfEntry 17 } ospfv3IfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each OSPFv3 neighbor } MAX-ACCESS read-create STATUS current DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effective- ly disables all multicast forwarding." DEFVAL { blocked } ::= { ospfv3IfEntry 18 } ospfv3IfDemand OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether Demand OSPFv3 procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface." DEFVAL { false } ::= { ospfv3IfEntry 19 } ospfv3IfMetricValue OBJECT-TYPE Internet Draft Expires May 2001 29 OSPFv3 MIB November 2000 SYNTAX Metric MAX-ACCESS read-create STATUS current DESCRIPTION "The metric assigned to this interface. The default value of the Metric is 10^8 / ifSpeed." ::= { ospfv3IfEntry 20 } ospfv3IfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link-Scope link-state advertisements in this link's link-state database." ::= { ospfv3IfEntry 21 } ospfv3IfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { ospfv3IfEntry 22 } ospfv3IfInstId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Enables multiple instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only." DEFVAL { 0 } ::= { ospfv3IfEntry 23 } -- OSPFv3 Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPFv3 Process is configured to -- carry on. Internet Draft Expires May 2001 30 OSPFv3 MIB November 2000 ospfv3VirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3VirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this router's virtual inter- faces." REFERENCE "OSPF Version 2, Appendix C.4 Virtual link parameters" ::= { ospfv3 8 } ospfv3VirtIfEntry OBJECT-TYPE SYNTAX Ospfv3VirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Virtual Interface." INDEX { ospfv3VirtIfAreaId, ospfv3VirtIfNeighbor } ::= { ospfv3VirtIfTable 1 } Ospfv3VirtIfEntry ::= SEQUENCE { ospfv3VirtIfAreaId AreaID, ospfv3VirtIfNeighbor RouterID, ospfv3VirtIfIndex Ipv6IfIndex, ospfv3VirtIfTransitDelay UpToMaxAge, ospfv3VirtIfRetransInterval UpToMaxAge, ospfv3VirtIfHelloInterval HelloRange, ospfv3VirtIfRtrDeadInterval PositiveInteger, ospfv3VirtIfState INTEGER, ospfv3VirtIfEvents Counter32, ospfv3VirtIfStatus RowStatus, ospfv3VirtIfLinkScopeLsaCount Gauge32, ospfv3VirtIfLinkLsaCksumSum Integer32 } ospfv3VirtIfAreaId OBJECT-TYPE SYNTAX AreaID Internet Draft Expires May 2001 31 OSPFv3 MIB November 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { ospfv3VirtIfEntry 1 } ospfv3VirtIfNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { ospfv3VirtIfEntry 2 } ospfv3VirtIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The interface index of this OSPFv3 virtual interface. It must be unique among all the interface indices on the router." ::= { ospfv3VirtIfEntry 3 } ospfv3VirtIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." DEFVAL { 1 } ::= { ospfv3VirtIfEntry 4 } ospfv3VirtIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time." DEFVAL { 5 } Internet Draft Expires May 2001 32 OSPFv3 MIB November 2000 ::= { ospfv3VirtIfEntry 5 } ospfv3VirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { ospfv3VirtIfEntry 6 } ospfv3VirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor." DEFVAL { 60 } ::= { ospfv3VirtIfEntry 7 } ospfv3VirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the ospfv3IfTable } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states." DEFVAL { down } ::= { ospfv3VirtIfEntry 8 } ospfv3VirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { ospfv3VirtIfEntry 9 } Internet Draft Expires May 2001 33 OSPFv3 MIB November 2000 ospfv3VirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfv3VirtIfEntry 10 } ospfv3VirtIfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link-Scope link-state advertisements in this virtual link's link-state database." ::= { ospfv3VirtIfEntry 11 } ospfv3VirtIfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { ospfv3VirtIfEntry 12 } -- OSPFv3 Neighbor Table -- The OSPFv3 Neighbor Table describes all neighbors in -- the locality of the subject router. ospfv3NbrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3NbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of non-virtual neighbor information." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" Internet Draft Expires May 2001 34 OSPFv3 MIB November 2000 ::= { ospfv3 9 } ospfv3NbrEntry OBJECT-TYPE SYNTAX Ospfv3NbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single neighbor." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" INDEX { ospfv3NbrIfIndex, ospfv3NbrIpv6Addr } ::= { ospfv3NbrTable 1 } Ospfv3NbrEntry ::= SEQUENCE { ospfv3NbrIfIndex Ipv6IfIndex, ospfv3NbrIpv6Addr Ipv6Address, ospfv3NbrRtrId RouterID, ospfv3NbrOptions Integer32, ospfv3NbrPriority DesignatedRouterPriority, ospfv3NbrState INTEGER, ospfv3NbrEvents Counter32, ospfv3NbrLsRetransQLen Gauge32, ospfv3NbmaNbrStatus RowStatus, ospfv3NbmaNbrPermanence INTEGER, ospfv3NbrHelloSuppressed TruthValue, ospfv3NbrIfId Ipv6IfIndex } ospfv3NbrIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The local link ID of the link over which the neighbor can be reached." ::= { ospfv3NbrEntry 1 } Internet Draft Expires May 2001 35 OSPFv3 MIB November 2000 ospfv3NbrIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 address of the neighbor associated with the local link." ::= { ospfv3NbrEntry 2 } ospfv3NbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System." ::= { ospfv3NbrEntry 3 } ospfv3NbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field." DEFVAL { 0 } ::= { ospfv3NbrEntry 4 } ospfv3NbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-create STATUS current DESCRIPTION "The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network." DEFVAL { 1 } ::= { ospfv3NbrEntry 5 } ospfv3NbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), Internet Draft Expires May 2001 36 OSPFv3 MIB November 2000 exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The State of the relationship with this Neigh- bor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" DEFVAL { down } ::= { ospfv3NbrEntry 6 } ospfv3NbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { ospfv3NbrEntry 7 } ospfv3NbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { ospfv3NbrEntry 8 } ospfv3NbmaNbrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfv3NbrEntry 9 } ospfv3NbmaNbrPermanence OBJECT-TYPE SYNTAX INTEGER { dynamic (1), -- learned through protocol permanent (2) -- configured address } MAX-ACCESS read-only Internet Draft Expires May 2001 37 OSPFv3 MIB November 2000 STATUS current DESCRIPTION "This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known." DEFVAL { permanent } ::= { ospfv3NbrEntry 10 } ospfv3NbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { ospfv3NbrEntry 11 } ospfv3NbrIfId OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index." ::= { ospfv3NbrEntry 12 } -- OSPFv3 Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. ospfv3VirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3VirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of virtual neighbor information." REFERENCE "OSPF Version 2, Section 15 Virtual Links" ::= { ospfv3 10 } ospfv3VirtNbrEntry OBJECT-TYPE SYNTAX Ospfv3VirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Virtual neighbor information." INDEX { ospfv3VirtNbrArea, ospfv3VirtNbrRtrId } Internet Draft Expires May 2001 38 OSPFv3 MIB November 2000 ::= { ospfv3VirtNbrTable 1 } Ospfv3VirtNbrEntry ::= SEQUENCE { ospfv3VirtNbrArea AreaID, ospfv3VirtNbrRtrId RouterID, ospfv3VirtNbrIfIndex Ipv6IfIndex, ospfv3VirtNbrIpv6Addr Ipv6Address, ospfv3VirtNbrOptions Integer32, ospfv3VirtNbrState INTEGER, ospfv3VirtNbrEvents Counter32, ospfv3VirtNbrLsRetransQLen Gauge32, ospfv3VirtNbrHelloSuppressed TruthValue, ospfv3VirtNbrIfId Ipv6IfIndex } ospfv3VirtNbrArea OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area Identifier." ::= { ospfv3VirtNbrEntry 1 } ospfv3VirtNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { ospfv3VirtNbrEntry 2 } ospfv3VirtNbrIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The local link ID for the virtual link over which the neighbor can be reached." ::= { ospfv3VirtNbrEntry 3 } Internet Draft Expires May 2001 39 OSPFv3 MIB November 2000 ospfv3VirtNbrIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 address used to reach this Virtual Neighbor. It must be a Site-Local or Global scope address." ::= { ospfv3VirtNbrEntry 4 } ospfv3VirtNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field." ::= { ospfv3VirtNbrEntry 5 } ospfv3VirtNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Virtual Neighbor Relation- ship." ::= { ospfv3VirtNbrEntry 6 } ospfv3VirtNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this virtual link has changed its state, or an error has occurred." ::= { ospfv3VirtNbrEntry 7 } ospfv3VirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 Internet Draft Expires May 2001 40 OSPFv3 MIB November 2000 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { ospfv3VirtNbrEntry 8 } ospfv3VirtNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { ospfv3VirtNbrEntry 9 } ospfv3VirtNbrIfId OBJECT-TYPE SYNTAX Ipv6IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface index." ::= { ospfv3VirtNbrEntry 10 } -- -- The OSPFv3 Area Aggregate Table -- ospfv3AreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospfv3AreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range sub- sumes another range the most specific match is the preferred one." ::= { ospfv3 11 } ospfv3AreaAggregateEntry OBJECT-TYPE SYNTAX Ospfv3AreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if Internet Draft Expires May 2001 41 OSPFv3 MIB November 2000 ranges are configured such that one range sub- sumes another range the most specific match is the preferred one." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" INDEX { ospfv3AreaAggregateAreaID, ospfv3AreaAggregateAreaLsdbType, ospfv3AreaAggregateIndex } ::= { ospfv3AreaAggregateTable 1 } Ospfv3AreaAggregateEntry ::= SEQUENCE { ospfv3AreaAggregateAreaID AreaID, ospfv3AreaAggregateAreaLsdbType INTEGER, ospfv3AreaAggregateIndex INTEGER, ospfv3AreaAggregatePrefix Ipv6AddressPrefix, ospfv3AreaAggregatePrefixLen INTEGER, ospfv3AreaAggregateStatus RowStatus, ospfv3AreaAggregateEffect INTEGER } ospfv3AreaAggregateAreaID OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Area the Address Aggregate is to be found within." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3AreaAggregateEntry 1 } ospfv3AreaAggregateAreaLsdbType OBJECT-TYPE SYNTAX INTEGER { interAreaPrefixLsa (8195), -- 0x2003 nssaExternalLsa (8199) -- 0x2007 } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Ag- gregate applies to." REFERENCE Internet Draft Expires May 2001 42 OSPFv3 MIB November 2000 "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfv3AreaAggregateEntry 2 } ospfv3AreaAggregateIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A unique identifier for this aggregate table entry." ::= { ospfv3AreaAggregateEntry 3 } ospfv3AreaAggregatePrefix OBJECT-TYPE SYNTAX Ipv6AddressPrefix MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 Prefix." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3AreaAggregateEntry 4 } ospfv3AreaAggregatePrefixLen OBJECT-TYPE SYNTAX INTEGER ( 3..128 ) UNITS "bits" MAX-ACCESS read-create STATUS current DESCRIPTION "The length of the prefix (in bits). A prefix can not be shorter than 3 bits." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfv3AreaAggregateEntry 5 } ospfv3AreaAggregateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfv3AreaAggregateEntry 6 } ospfv3AreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), Internet Draft Expires May 2001 43 OSPFv3 MIB November 2000 doNotAdvertiseMatching (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the prefix not being advertised at all outside the area." DEFVAL { advertiseMatching } ::= { ospfv3AreaAggregateEntry 7 } -- conformance information ospfv3Conformance OBJECT IDENTIFIER ::= { ospfv3 12 } ospfv3Groups OBJECT IDENTIFIER ::= { ospfv3Conformance 1 } ospfv3Compliances OBJECT IDENTIFIER ::= { ospfv3Conformance 2 } -- compliance statements ospfv3Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement " MODULE -- this module MANDATORY-GROUPS { ospfv3BasicGroup, ospfv3AreaGroup, ospfv3IfGroup, ospfv3VirtIfGroup, ospfv3NbrGroup, ospfv3VirtNbrGroup, ospfv3AreaAggregateGroup } ::= { ospfv3Compliances 1 } -- units of conformance ospfv3BasicGroup OBJECT-GROUP OBJECTS { ospfv3RouterId, ospfv3AdminStat, ospfv3VersionNumber, ospfv3AreaBdrRtrStatus, ospfv3ASBdrRtrStatus, ospfv3AsScopeLsaCount, ospfv3AsScopeLsaCksumSum, ospfv3OriginateNewLsas, ospfv3RxNewLsas, ospfv3ExtAreaLsdbLimit, Internet Draft Expires May 2001 44 OSPFv3 MIB November 2000 ospfv3MulticastExtensions, ospfv3ExitOverflowInterval, ospfv3DemandExtensions, ospfv3TrafficEngineeringSupport } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems." ::= { ospfv3Groups 1 } ospfv3AreaGroup OBJECT-GROUP OBJECTS { ospfv3AreaId, ospfv3ImportAsExtern, ospfv3SpfRuns, ospfv3AreaBdrRtrCount, ospfv3AsBdrRtrCount, ospfv3AreaScopeLsaCount, ospfv3AreaScopeLsaCksumSum, ospfv3AreaSummary, ospfv3AreaStatus, ospfv3StubMetric, ospfv3AreaNssaTranslatorRole, ospfv3AreaNssaTranslatorState, ospfv3AreaNssaTranslatorStabilityInterval, ospfv3AreaNssaTranslatorEvents } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems supporting areas." ::= { ospfv3Groups 2 } ospfv3AsLsdbGroup OBJECT-GROUP OBJECTS { ospfv3AsLsdbType, ospfv3AsLsdbRouterId, ospfv3AsLsdbLsid, ospfv3AsLsdbSequence, ospfv3AsLsdbAge, ospfv3AsLsdbChecksum, ospfv3AsLsdbAdvertisement } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems that display their AS-scope link state database." ::= { ospfv3Groups 3 } ospfv3AreaLsdbGroup OBJECT-GROUP Internet Draft Expires May 2001 45 OSPFv3 MIB November 2000 OBJECTS { ospfv3AreaLsdbAreaId, ospfv3AreaLsdbType, ospfv3AreaLsdbRouterId, ospfv3AreaLsdbLsid, ospfv3AreaLsdbSequence, ospfv3AreaLsdbAge, ospfv3AreaLsdbChecksum, ospfv3AreaLsdbAdvertisement } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems that display their Area-scope link state database." ::= { ospfv3Groups 4 } ospfv3LinkLsdbGroup OBJECT-GROUP OBJECTS { ospfv3LinkLsdbIfIndex, ospfv3LinkLsdbType, ospfv3LinkLsdbRouterId, ospfv3LinkLsdbLsid, ospfv3LinkLsdbSequence, ospfv3LinkLsdbAge, ospfv3LinkLsdbChecksum, ospfv3LinkLsdbAdvertisement } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems that display their Link-scope link state database." ::= { ospfv3Groups 5 } ospfv3HostGroup OBJECT-GROUP OBJECTS { ospfv3HostIpv6Address, ospfv3HostMetric, ospfv3HostStatus, ospfv3HostAreaID } STATUS current DESCRIPTION "These objects are required for OSPFv3 systems that support attached hosts." ::= { ospfv3Groups 6 } ospfv3IfGroup OBJECT-GROUP OBJECTS { ospfv3IfIndex, ospfv3IfAreaId, Internet Draft Expires May 2001 46 OSPFv3 MIB November 2000 ospfv3IfType, ospfv3IfAdminStat, ospfv3IfRtrPriority, ospfv3IfTransitDelay, ospfv3IfRetransInterval, ospfv3IfHelloInterval, ospfv3IfRtrDeadInterval, ospfv3IfPollInterval, ospfv3IfState, ospfv3IfDesignatedRouter, ospfv3IfBackupDesignatedRouter, ospfv3IfEvents, ospfv3IfStatus, ospfv3IfMulticastForwarding, ospfv3IfDemand, ospfv3IfMetricValue, ospfv3IfLinkScopeLsaCount, ospfv3IfLinkLsaCksumSum, ospfv3IfInstId } STATUS current DESCRIPTION "These interface objects are required for OSPFv3 systems." ::= { ospfv3Groups 7 } ospfv3VirtIfGroup OBJECT-GROUP OBJECTS { ospfv3VirtIfAreaId, ospfv3VirtIfNeighbor, ospfv3VirtIfIndex, ospfv3VirtIfTransitDelay, ospfv3VirtIfRetransInterval, ospfv3VirtIfHelloInterval, ospfv3VirtIfRtrDeadInterval, ospfv3VirtIfState, ospfv3VirtIfEvents, ospfv3VirtIfStatus, ospfv3VirtIfLinkScopeLsaCount, ospfv3VirtIfLinkLsaCksumSum } STATUS current DESCRIPTION "These virtual interface objects are required for OSPFv3 systems." ::= { ospfv3Groups 8 } ospfv3NbrGroup OBJECT-GROUP OBJECTS { ospfv3NbrIfIndex, ospfv3NbrIpv6Addr, Internet Draft Expires May 2001 47 OSPFv3 MIB November 2000 ospfv3NbrRtrId, ospfv3NbrOptions, ospfv3NbrPriority, ospfv3NbrState, ospfv3NbrEvents, ospfv3NbrLsRetransQLen, ospfv3NbmaNbrStatus, ospfv3NbmaNbrPermanence, ospfv3NbrHelloSuppressed, ospfv3NbrIfId } STATUS current DESCRIPTION "These neighbor objects are required for OSPFv3 systems." ::= { ospfv3Groups 9 } ospfv3VirtNbrGroup OBJECT-GROUP OBJECTS { ospfv3VirtNbrArea, ospfv3VirtNbrRtrId, ospfv3VirtNbrIfIndex, ospfv3VirtNbrIpv6Addr, ospfv3VirtNbrOptions, ospfv3VirtNbrState, ospfv3VirtNbrEvents, ospfv3VirtNbrLsRetransQLen, ospfv3VirtNbrHelloSuppressed, ospfv3VirtNbrIfId } STATUS current DESCRIPTION "These virtual neighbor objects are required for OSPFv3 systems." ::= { ospfv3Groups 10 } ospfv3AreaAggregateGroup OBJECT-GROUP OBJECTS { ospfv3AreaAggregateAreaID, ospfv3AreaAggregateAreaLsdbType, ospfv3AreaAggregateIndex, ospfv3AreaAggregatePrefix, ospfv3AreaAggregatePrefixLen, ospfv3AreaAggregateStatus, ospfv3AreaAggregateEffect } STATUS current DESCRIPTION "These area aggregate objects are required for OSPFv3 systems." ::= { ospfv3Groups 11 } Internet Draft Expires May 2001 48 OSPFv3 MIB November 2000 END -- -- Copyright (C) The Internet Society (2000). All Rights -- Reserved. -- -- This document and translations of it may be copied and -- furnished to others, and derivative works that comment on or -- -- Internet Draft Expires May 2001 53 -- OSPFv3 MIB November 2000 -- -- -- otherwise explain it or assist in its implementation may be -- prepared, copied, published and distributed, in whole or in -- part, without restriction of any kind, provided that the above -- copyright notice and this paragraph are included on all such -- copies and derivative works. However, this document itself -- may not be modified in any way, such as by removing the -- copyright notice or references to the Internet Society or -- other Internet organizations, except as needed for the purpose -- of developing Internet standards in which case the procedures -- for copyrights defined in the Internet Standards process must -- be followed, or as required to translate it into languages -- other than English. -- -- The limited permissions granted above are perpetual and will -- not be revoked by the Internet Society or its successors or -- assigns. -- -- This document and the information contained herein is provided -- on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR -- IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE -- USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR -- ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A -- PARTICULAR PURPOSE. -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Internet Draft Expires May 2001 54