-- extracted from draft-ietf-pwe3-pw-atm-mib-01.txt -- at Wed Nov 8 06:07:29 2006 PW-ATM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, experimental, Integer32, Counter32, Counter64,Unsigned32, transmission FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TruthValue, RowStatus, RowPointer FROM SNMPv2-TC PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB InterfaceIndex FROM IF-MIB pwIndex FROM PW-STD-MIB AtmVpIdentifier, AtmVcIdentifier FROM ATM-TC-MIB; pwAtmMIB MODULE-IDENTITY LAST-UPDATED "200608210000Z" -- 21 August 2006 ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) Working Group" CONTACT-INFO "Senthilkumar Sathappan Postal: 1000 Marconi Drive Warrendale PA 15086 Tel: +1-724-742-6147 Email: senthilkumar.sathappan@marconi.com Marichetty Venkatesan Postal: 1000 Marconi Drive Warrendale PA 15086 Tel: +1-724-742-7058 Email: venkatesan.marichetty@marconi.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Tel: +1-978-497-3051 Email: tnadeau@cisco.com Orly Nicklass RAD Data Communications 24 Raoul Wallenberg St., Bldg C Tel Aviv 69719, Israel Email: orly_n@rad.com Discussion and general questions should be posed to the PWE3 Working Group (pwe3@ietf.org)." DESCRIPTION "This MIB contains managed object definitions for Pseudo Wire emulation of ATM over Packet Switched Networks (PSN). This MIB reports to the PW-MIB. The PW-MIB contains structures and MIB associations generic to Pseudo-Wire Virtual Circuit (PW) emulation. PW-specific MIBs (such as this) contain config and stats for specific PW types. This version of this MIB module is part of RFC XXXX;" -- RFC Ed.: replace XXXX with actual RFC number & remove this -- note" -- Revision history. REVISION "200608210000Z" -- 21 August 2006 DESCRIPTION "First updated version" REVISION "200310160000Z" -- 16 October 2003 12:00:00 EST DESCRIPTION "Original version." ::= { transmission YYYY } -- To be assigned by IANA -- RFC Editor: please replace YYYY based on the IANA -- allocation and remove this note. -- Top-level components of this MIB pwAtmNotifications OBJECT IDENTIFIER ::= { pwAtmMIB 0 } pwAtmObjects OBJECT IDENTIFIER ::= { pwAtmMIB 1 } pwAtmConformance OBJECT IDENTIFIER ::= { pwAtmMIB 2 } -- ATM PW Outbound Table for 1 to 1 connection pwAtmOutboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. An entry is created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCell1to1Vcc(12), atmCell1to1Vpc(13) or atmAal5PduVcc(14)." ::= { pwAtmObjects 1 } pwAtmOutboundEntry OBJECT-TYPE SYNTAX PwAtmOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable." INDEX { pwIndex } ::= { pwAtmOutboundTable 1 } PwAtmOutboundEntry ::= SEQUENCE { pwAtmOutboundAtmIf InterfaceIndex, pwAtmOutboundVpi AtmVpIdentifier, pwAtmOutboundVci AtmVcIdentifier, pwAtmOutboundTrafficParamDescr RowPointer, pwAtmOutboundRowStatus RowStatus, pwAtmOutboundClpQosMapping TruthValue, -- deprecated pwAtmOutboundOamCellSupported TruthValue, -- deprecated pwAtmOutboundQosScalingFactor Integer32 -- deprecated } pwAtmOutboundAtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM Interface that receives cells from the ATM network." ::= { pwAtmOutboundEntry 1 } pwAtmOutboundVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VPI value of this ATM PW. The value may indicate the translated value when egress generates new VPI." ::= { pwAtmOutboundEntry 2 } pwAtmOutboundVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VCI value of this ATM PW. The value may indicate the translated value when egress generates new VCI." ::= { pwAtmOutboundEntry 3 } pwAtmOutboundTrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a pointer to an ATM traffic parameter specification table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort" ::= { pwAtmOutboundEntry 4 } pwAtmOutboundRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { pwAtmOutboundEntry 5 } pwAtmOutboundClpQosMapping OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields (e.g. EXP fields of the MPLS Label Stack) of the encapsulating protocol. Selecting True allows the drop precedence to be preserved across the PSN." REFERENCE "See [ATMENCAP] section 12" ::= { pwAtmOutboundEntry 6} pwAtmOutboundOamCellSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This Object indicates whether OAM Cells are transported on this PW." ::= { pwAtmOutboundEntry 7 } pwAtmOutboundQosScalingFactor OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This Object represents the scaling factor (% value) to be applied to ATM QoS rates when calculating QoS rates for the PSN domain . For example, in the cell transport mode the bandwidth needed in the PSN domain will be higher (since PSN Transport header, PW header, and optional control word have to transmitted with every cell), whereas in the AAL5 mode the bandwidth needed in PSN domain will be less since cell headers will be removed after reassembly." DEFVAL { 100 } ::= { pwAtmOutboundEntry 8} -- End of ATM PW Outbound Table pwAtmOutboundPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmOutboundPerfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table specifies performance-related attributes for an ATM PW in the outbound direction." ::= { pwAtmObjects 2 } pwAtmOutboundPerfEntry OBJECT-TYPE SYNTAX PwAtmOutboundPerfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A row in this table represents performance for an ATM PW in the outbound direction" AUGMENTS { pwAtmOutboundEntry } ::= { pwAtmOutboundPerfTable 1 } PwAtmOutboundPerfEntry ::= SEQUENCE { pwAtmOutboundCellsReceived Counter32, pwAtmOutboundCellsRejected Counter32, pwAtmOutboundCellsTagged Counter32, pwAtmOutboundHCCellsReceived Counter64, pwAtmOutboundHCCellsRejected Counter64, pwAtmOutboundHCCellsTagged Counter64 } pwAtmOutboundCellsReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This Object indicates the number of cells received by this PW." ::= { pwAtmOutboundPerfEntry 1 } pwAtmOutboundCellsRejected OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This Object indicates the number of cells that were rejected by this PW because of policing." ::= { pwAtmOutboundPerfEntry 2 } pwAtmOutboundCellsTagged OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This Object indicates the number of cells that were Tagged." ::= { pwAtmOutboundPerfEntry 3 } pwAtmOutboundHCCellsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "High capacity counter for number of cells received by this PW." ::= { pwAtmOutboundPerfEntry 4 } pwAtmOutboundHCCellsRejected OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "High Capacity counter for number of cells that were rejected by this PW because of policing." ::= { pwAtmOutboundPerfEntry 5 } pwAtmOutboundHCCellsTagged OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "High capacity counter for number of cells that were Tagged." ::= { pwAtmOutboundPerfEntry 6 } -- End of ATM PW Outbound Perf Table -- ATM PW Inbound Table for 1 to 1 mode pwAtmInboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW in the Inbound direction." ::= { pwAtmObjects 3 } pwAtmInboundEntry OBJECT-TYPE SYNTAX PwAtmInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be sent into the ATM Network after reconstructing cells from Packets received from a PSN. This table is indexed by pwIndex from pwTable. An entry is created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCell1to1Vcc(12), atmCell1to1Vpc(13) or atmAal5PduVcc(14)" INDEX { pwIndex } ::= { pwAtmInboundTable 1 } PwAtmInboundEntry ::= SEQUENCE { pwAtmInboundAtmIf InterfaceIndex, pwAtmInboundVpi AtmVpIdentifier, pwAtmInboundVci AtmVcIdentifier, pwAtmInboundTrafficParamDescr RowPointer, pwAtmInboundRowStatus RowStatus, pwAtmInboundOamCellSupported TruthValue --deprecated } pwAtmInboundAtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM Interface that sends cells into the ATM network after reconstructing cells from packets received from a PSN." ::= { pwAtmInboundEntry 1 } pwAtmInboundVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VPI value of this ATM PW. If the pwType is atmNto1Transparent then the value will be set to zero." ::= { pwAtmInboundEntry 2 } pwAtmInboundVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VCI value of this ATM PW. If the pwType is atmNto1Transparent atmCell1to1Vpc or atmCellNto1Vpc then the value should be set to zero." ::= { pwAtmInboundEntry 3 } pwAtmInboundTrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a pointer to a ATM traffic parameter specification table which will be employed while transmit into the ATM network. This table contains a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort." ::= { pwAtmInboundEntry 4 } pwAtmInboundRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { pwAtmInboundEntry 5 } pwAtmInboundOamCellSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This Object indicates whether this PW can receive OAM Cells." ::= { pwAtmInboundEntry 6 } -- End of ATM PW Inbound Table -- ATM PW Inbound Perf Table pwAtmInboundPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmInboundPerfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table specifies the performance for an ATM PW in the Inbound direction." ::= { pwAtmObjects 4 } pwAtmInboundPerfEntry OBJECT-TYPE SYNTAX PwAtmInboundPerfEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table specifies performance-related attributes for an ATM PW in the inbound direction." AUGMENTS { pwAtmInboundEntry } ::= {pwAtmInboundPerfTable 1} PwAtmInboundPerfEntry ::= SEQUENCE { pwAtmInboundPerfCellsXmit Counter32, pwAtmInboundPerfCellsLost Counter32, pwAtmInboundPerfHCCellsXmit Counter64, pwAtmInboundPerfHCCellsLost Counter64 } pwAtmInboundPerfCellsXmit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This Object indicates the number of cells that were transmitted into ATM network by this PW." ::= { pwAtmInboundPerfEntry 1 } pwAtmInboundPerfCellsLost OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This Object indicates the number of cells that were dropped by this PW." ::= { pwAtmInboundPerfEntry 2 } pwAtmInboundPerfHCCellsXmit OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "High Capacity counter for the number of cells that were transmitted into ATM network by this PW." ::= { pwAtmInboundPerfEntry 3 } pwAtmInboundPerfHCCellsLost OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "High Capacity counter for number of cells that were dropped by this PW." ::= { pwAtmInboundPerfEntry 4 } -- End of ATM PW Inbound Table --Generic ATM PW table for any type of PW ATM connection. pwAtmCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies generic information for an ATM PW to be carried over PSN in any mode." ::= { pwAtmObjects 5 } pwAtmCfgEntry OBJECT-TYPE SYNTAX PwAtmCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters for the ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable." INDEX { pwIndex } ::= { pwAtmCfgTable 1 } PwAtmCfgEntry ::= SEQUENCE { pwAtmCfgMaxCellConcatenation Unsigned32, pwAtmCfgFarEndMaxCellConcatenation Unsigned32, pwAtmCfgTimeoutMode INTEGER, pwAtmClpQosMapping TruthValue, pwAtmOamCellSupported TruthValue } pwAtmCfgMaxCellConcatenation OBJECT-TYPE SYNTAX Unsigned32 (1..29) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of ATM cells that can be concatenated into one PW packet towards PSN." ::= { pwAtmCfgEntry 1 } pwAtmCfgFarEndMaxCellConcatenation OBJECT-TYPE SYNTAX Unsigned32 (1..29) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will return value 0." ::= { pwAtmCfgEntry 2 } pwAtmCfgTimeoutMode OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), disabled (2), enabled (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the time out is implementation specific" ::= { pwAtmCfgEntry 3 } pwAtmClpQosMapping OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields of the encapsulating protocol (e.g. EXP fields of the MPLS Label Stack). Selecting True allows the drop precedence to be preserved across the PSN. " REFERENCE "See [ATMENCAP] section 12" ::= { pwAtmCfgEntry 4 } pwAtmOamCellSupported OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This Object indicates whether OAM Cells are transported on this PW." ::= { pwAtmCfgEntry 5 } -- Device capable of implementing N:1 and 1:1 mode assumes to support -- the N:1 table for both modes with respective applicable setting. -- In such implementation, creating an entry for 1:1 mode is -- needed only in pwAtmInboundNto1Table. The side effect of such -- will be an automatic creat of the respective line in the -- pwAtmOutboundNto1Table. -- ATM PW Outbound Table for N to 1 connection pwAtmOutboundNto1Table OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmOutboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14). An entry can be created only when the VP/VC are known." ::= { pwAtmObjects 6 } pwAtmOutboundNto1Entry OBJECT-TYPE SYNTAX PwAtmOutboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs" INDEX { pwIndex, pwAtmOutboundNto1AtmIf , pwAtmOutboundNto1Vpi, pwAtmOutboundNto1Vci } ::= { pwAtmOutboundNto1Table 1 } PwAtmOutboundNto1Entry ::= SEQUENCE { pwAtmOutboundNto1AtmIf InterfaceIndex, pwAtmOutboundNto1Vpi AtmVpIdentifier, pwAtmOutboundNto1Vci AtmVcIdentifier, pwAtmOutboundNto1RowStatus RowStatus, pwAtmOutboundNto1TrafficParamDescr RowPointer, pwAtmOutboundNto1MappedVpi AtmVpIdentifier, pwAtmOutboundNto1MappedVci AtmVcIdentifier } pwAtmOutboundNto1AtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Interface that receives cells from the ATM network." ::= { pwAtmOutboundNto1Entry 1 } pwAtmOutboundNto1Vpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPI value of this ATM PW." ::= { pwAtmOutboundNto1Entry 2 } pwAtmOutboundNto1Vci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VCI value of this ATM PW. In VP case, the value will be the equivalent of 0xFFFFFFFF" ::= { pwAtmOutboundNto1Entry 3 } pwAtmOutboundNto1RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { pwAtmOutboundNto1Entry 4 } pwAtmOutboundNto1TrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a pointer to a ATM traffic parameter specification table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort." ::= { pwAtmOutboundNto1Entry 5 } pwAtmOutboundNto1MappedVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13) " ::= { pwAtmOutboundNto1Entry 6 } pwAtmOutboundNto1MappedVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The egress generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case, the value will be the equivalent of 0xFFFFFFFF" ::= { pwAtmOutboundNto1Entry 7 } -- ATM PW Inbound Table for N to 1 connection pwAtmInboundNto1Table OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmInboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14)." ::= { pwAtmObjects 7 } pwAtmInboundNto1Entry OBJECT-TYPE SYNTAX PwAtmInboundNto1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs" INDEX { pwIndex, pwAtmInboundNto1AtmIf , pwAtmInboundNto1Vpi, pwAtmInboundNto1Vci } ::= { pwAtmInboundNto1Table 1 } PwAtmInboundNto1Entry ::= SEQUENCE { pwAtmInboundNto1AtmIf InterfaceIndex, pwAtmInboundNto1Vpi AtmVpIdentifier, pwAtmInboundNto1Vci AtmVcIdentifier, pwAtmInboundNto1RowStatus RowStatus, pwAtmInboundNto1TrafficParamDescr RowPointer, pwAtmInboundNto1MappedVpi AtmVpIdentifier, pwAtmInboundNto1MappedVci AtmVcIdentifier } pwAtmInboundNto1AtmIf OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Interface that receives cells from the ATM network." ::= { pwAtmInboundNto1Entry 1 } pwAtmInboundNto1Vpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VPI value of this ATM PW." ::= { pwAtmInboundNto1Entry 2 } pwAtmInboundNto1Vci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "VCI value of this ATM PW.In VP case, the value will be the equivalent of 0xFFFFFFFF" ::= { pwAtmInboundNto1Entry 3 } pwAtmInboundNto1RowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This Object is used to create, modify or delete a row in this table." ::= { pwAtmInboundNto1Entry 4 } pwAtmInboundNto1TrafficParamDescr OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a pointer to a ATM traffic parameter specification table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort." ::= { pwAtmInboundNto1Entry 5 } pwAtmInboundNto1MappedVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The generated VPI value of this ATM PW. " ::= { pwAtmInboundNto1Entry 6 } pwAtmInboundNto1MappedVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION " The generated VCI value of this ATM PW. In VP case, the value will be the equivalent of 0xFFFFFFFF" ::= { pwAtmInboundNto1Entry 7 } -- ATM PW Outbound Perf Table -- The following counters supplement the counters presented in the -- PW generic MIB -- ATM PW Performance Current Table. pwAtmPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The current 15 minute interval counts are in this table. This table provides performance information per ATM PW." ::= { pwAtmObjects 8 } pwAtmPerfCurrentEntry OBJECT-TYPE SYNTAX PwAtmPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwAtmPerfInterval table and the counts in this entry are reset to zero." INDEX { pwIndex } ::= { pwAtmPerfCurrentTable 1 } PwAtmPerfCurrentEntry ::= SEQUENCE { pwAtmPerfCurrentMissingPkts PerfCurrentCount, pwAtmPerfCurrentPktsReOrder PerfCurrentCount, pwAtmPerfCurrentPktsMisOrder PerfCurrentCount, pwAtmPerfCurrentPktsTimeout PerfCurrentCount, pwAtmPerfCurrentCellsXmit PerfCurrentCount, pwAtmPerfCurrentCellsDropped PerfCurrentCount, pwAtmPerfCurrentCellsReceived PerfCurrentCount, pwAtmPerfCurrentUnknownCells PerfCurrentCount } pwAtmPerfCurrentMissingPkts OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { pwAtmPerfCurrentEntry 1 } pwAtmPerfCurrentPktsReOrder OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature." ::= { pwAtmPerfCurrentEntry 2 } pwAtmPerfCurrentPktsMisOrder OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order (via control word sequence numbers)." ::= { pwAtmPerfCurrentEntry 3 } pwAtmPerfCurrentPktsTimeout OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration while attempting to collect cells." ::= { pwAtmPerfCurrentEntry 4 } pwAtmPerfCurrentCellsXmit OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted cells." ::= { pwAtmPerfCurrentEntry 5 } pwAtmPerfCurrentCellsDropped OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { pwAtmPerfCurrentEntry 6 } pwAtmPerfCurrentCellsReceived OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received cells." ::= { pwAtmPerfCurrentEntry 7 } pwAtmPerfCurrentUnknownCells OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI values." ::= { pwAtmPerfCurrentEntry 8 } -- End ATM PW Performance Current Interval Table -- ATM PW Performance Interval Table. pwAtmPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period. " ::= { pwAtmObjects 9 } pwAtmPerfIntervalEntry OBJECT-TYPE SYNTAX PwAtmPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval. " INDEX { pwIndex, pwAtmPerfIntervalNumber } ::= { pwAtmPerfIntervalTable 1 } PwAtmPerfIntervalEntry ::= SEQUENCE { pwAtmPerfIntervalNumber Unsigned32, pwAtmPerfIntervalValidData TruthValue, pwAtmPerfIntervalDuration Unsigned32, pwAtmPerfIntervalMissingPkts PerfIntervalCount, pwAtmPerfIntervalPktsReOrder PerfIntervalCount, pwAtmPerfIntervalPktsMisOrder PerfIntervalCount, pwAtmPerfIntervalPktsTimeout PerfIntervalCount, pwAtmPerfIntervalCellsXmit PerfIntervalCount, pwAtmPerfIntervalCellsDropped PerfIntervalCount, pwAtmPerfIntervalCellsReceived PerfIntervalCount, pwAtmPerfIntervalUnknownCells PerfIntervalCount } pwAtmPerfIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96." ::= { pwAtmPerfIntervalEntry 1 } pwAtmPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwAtmPerfIntervalEntry 2 } pwAtmPerfIntervalDuration OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { pwAtmPerfIntervalEntry 3 } pwAtmPerfIntervalMissingPkts OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { pwAtmPerfIntervalEntry 4 } pwAtmPerfIntervalPktsReOrder OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature." ::= { pwAtmPerfIntervalEntry 5 } pwAtmPerfIntervalPktsMisOrder OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order (via control word sequence numbers)." ::= { pwAtmPerfIntervalEntry 6 } pwAtmPerfIntervalPktsTimeout OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration." ::= { pwAtmPerfIntervalEntry 7 } pwAtmPerfIntervalCellsXmit OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted cells." ::= { pwAtmPerfIntervalEntry 8 } pwAtmPerfIntervalCellsDropped OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { pwAtmPerfIntervalEntry 9 } pwAtmPerfIntervalCellsReceived OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received cells." ::= { pwAtmPerfIntervalEntry 10 } pwAtmPerfIntervalUnknownCells OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI values." ::= { pwAtmPerfIntervalEntry 11 } -- End ATM PW Performance Interval Table -- ATM PW 1day Performance Table pwAtmPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwAtmPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical 1 day intervals up to one full month." ::= { pwAtmObjects 10 } pwAtmPerf1DayIntervalEntry OBJECT-TYPE SYNTAX PwAtmPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in this table by the agent for every entry in the pwAtmCfgTable table." INDEX { pwIndex,pwAtmPerf1DayIntervalNumber } ::= { pwAtmPerf1DayIntervalTable 1 } PwAtmPerf1DayIntervalEntry ::= SEQUENCE { pwAtmPerf1DayIntervalNumber Unsigned32, pwAtmPerf1DayIntervalValidData TruthValue, pwAtmPerf1DayIntervalDuration Unsigned32, pwAtmPerf1DayIntervalMissingPkts Counter32, pwAtmPerf1DayIntervalPktsReOrder Counter32, pwAtmPerf1DayIntervalPktsMisOrder Counter32, pwAtmPerf1DayIntervalPktsTimeout Counter32, pwAtmPerf1DayIntervalCellsXmit Counter32, pwAtmPerf1DayIntervalCellsDropped Counter32, pwAtmPerf1DayIntervalCellsReceived Counter32, pwAtmPerf1DayIntervalUnknownCells Counter32 } pwAtmPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively" ::= { pwAtmPerf1DayIntervalEntry 1 } pwAtmPerf1DayIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwAtmPerf1DayIntervalEntry 2 } pwAtmPerf1DayIntervalDuration OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { pwAtmPerf1DayIntervalEntry 3 } pwAtmPerf1DayIntervalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via control word sequence number gaps)." ::= { pwAtmPerf1DayIntervalEntry 4 } pwAtmPerf1DayIntervalPktsReOrder OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature." ::= { pwAtmPerf1DayIntervalEntry 5 } pwAtmPerf1DayIntervalPktsMisOrder OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered." ::= { pwAtmPerf1DayIntervalEntry 6 } pwAtmPerf1DayIntervalPktsTimeout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets transmitted due to timeout expiration." ::= { pwAtmPerf1DayIntervalEntry 7 } pwAtmPerf1DayIntervalCellsXmit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of transmitted cells." ::= { pwAtmPerf1DayIntervalEntry 8 } pwAtmPerf1DayIntervalCellsDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of dropped cells." ::= { pwAtmPerf1DayIntervalEntry 9 } pwAtmPerf1DayIntervalCellsReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of received cells." ::= { pwAtmPerf1DayIntervalEntry 10 } pwAtmPerf1DayIntervalUnknownCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of cells received from the PSN with unknown VPI or VCI value." ::= { pwAtmPerf1DayIntervalEntry 11 } -- End of ATM PW Performance table pwAtmGroups OBJECT IDENTIFIER ::= { pwAtmConformance 1 } pwAtmCompliances OBJECT IDENTIFIER ::= { pwAtmConformance 2 } pwAtmModuleCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for agent that support PW ATM." MODULE -- this module MANDATORY-GROUPS { pwAtmOutboundGroup, pwAtmOutboundPerfGroup, pwAtmInboundGroup, pwAtmInboundPerfGroup } ::= { pwAtmCompliances 1 } -- Units of conformance. pwAtmOutboundGroup OBJECT-GROUP OBJECTS { pwAtmOutboundAtmIf, pwAtmOutboundVpi, pwAtmOutboundVci, pwAtmOutboundTrafficParamDescr, pwAtmOutboundRowStatus, pwAtmOutboundClpQosMapping, pwAtmOutboundOamCellSupported, pwAtmOutboundQosScalingFactor } STATUS deprecated DESCRIPTION "Collection of objects for basic ATM PW outbound config." ::= { pwAtmGroups 1 } pwAtmOutboundPerfGroup OBJECT-GROUP OBJECTS { pwAtmOutboundCellsReceived, pwAtmOutboundCellsRejected, pwAtmOutboundCellsTagged, pwAtmOutboundHCCellsReceived, pwAtmOutboundHCCellsRejected, pwAtmOutboundHCCellsTagged } STATUS deprecated DESCRIPTION "Collection of objects counting various outbound ATM PW statistics." ::= { pwAtmGroups 2 } pwAtmInboundGroup OBJECT-GROUP OBJECTS { pwAtmInboundAtmIf, pwAtmInboundVpi, pwAtmInboundVci, pwAtmInboundTrafficParamDescr, pwAtmInboundRowStatus, pwAtmInboundOamCellSupported } STATUS deprecated DESCRIPTION "Collection of objects for basic ATM PW inbound config." ::= { pwAtmGroups 3 } pwAtmInboundPerfGroup OBJECT-GROUP OBJECTS { pwAtmInboundPerfCellsXmit, pwAtmInboundPerfCellsLost, pwAtmInboundPerfHCCellsXmit, pwAtmInboundPerfHCCellsLost } STATUS deprecated DESCRIPTION "Collection of objects counting various inbound ATM PW statistics." ::= { pwAtmGroups 4 } pwAtmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agent that support PW ATM." MODULE -- this module MANDATORY-GROUPS { pwAtmCfgGroup, pwAtmPerfGroup } GROUP pwAtmOutbound1to1Group DESCRIPTION "This group is only mandatory for implementations that support the ATM PW 1:1 mode." GROUP pwAtmInbound1to1Group DESCRIPTION "This group is only mandatory for implementations that support the ATM PW 1:1 mode." GROUP pwAtmOutboundNto1Group DESCRIPTION "This group is only mandatory for implementations that support the ATM PW N:1 mode." GROUP pwAtmInboundNto1Group DESCRIPTION "This group is only mandatory for implementations that support the ATM PW N:1 mode." ::= { pwAtmCompliances 2 } -- Units of conformance. pwAtmCfgGroup OBJECT-GROUP OBJECTS {pwAtmCfgMaxCellConcatenation, pwAtmCfgFarEndMaxCellConcatenation, pwAtmCfgTimeoutMode, pwAtmClpQosMapping, pwAtmOamCellSupported } STATUS current DESCRIPTION "Collection of objects for basic ATM PW config." ::= { pwAtmGroups 5 } pwAtmPerfGroup OBJECT-GROUP OBJECTS {pwAtmPerfCurrentMissingPkts, pwAtmPerfCurrentPktsReOrder, pwAtmPerfCurrentPktsMisOrder, pwAtmPerfCurrentPktsTimeout, pwAtmPerfCurrentCellsXmit, pwAtmPerfCurrentCellsDropped, pwAtmPerfCurrentCellsReceived, pwAtmPerfCurrentUnknownCells, pwAtmPerfIntervalValidData, pwAtmPerfIntervalDuration, pwAtmPerfIntervalMissingPkts, pwAtmPerfIntervalPktsReOrder, pwAtmPerfIntervalPktsMisOrder, pwAtmPerfIntervalPktsTimeout, pwAtmPerfIntervalCellsXmit, pwAtmPerfIntervalCellsDropped, pwAtmPerfIntervalCellsReceived, pwAtmPerfIntervalUnknownCells, pwAtmPerf1DayIntervalValidData, pwAtmPerf1DayIntervalDuration, pwAtmPerf1DayIntervalMissingPkts, pwAtmPerf1DayIntervalPktsReOrder, pwAtmPerf1DayIntervalPktsMisOrder, pwAtmPerf1DayIntervalPktsTimeout, pwAtmPerf1DayIntervalCellsXmit, pwAtmPerf1DayIntervalCellsDropped, pwAtmPerf1DayIntervalCellsReceived, pwAtmPerf1DayIntervalUnknownCells } STATUS current DESCRIPTION "Collection of objects for basic ATM PW Performance." ::= { pwAtmGroups 6 } pwAtmOutbound1to1Group OBJECT-GROUP OBJECTS {pwAtmOutboundAtmIf, pwAtmOutboundVpi, pwAtmOutboundVci, pwAtmOutboundTrafficParamDescr, pwAtmOutboundRowStatus } STATUS current DESCRIPTION "Collection of objects for basic 1:1 ATM PW outbound config." ::= { pwAtmGroups 7 } pwAtmInbound1to1Group OBJECT-GROUP OBJECTS {pwAtmInboundAtmIf, pwAtmInboundVpi, pwAtmInboundVci, pwAtmInboundTrafficParamDescr, pwAtmInboundRowStatus } STATUS current DESCRIPTION "Collection of objects for basic 1:1 ATM PW inbound config." ::= { pwAtmGroups 8 } pwAtmOutboundNto1Group OBJECT-GROUP OBJECTS {pwAtmOutboundNto1RowStatus, pwAtmOutboundNto1TrafficParamDescr, pwAtmOutboundNto1MappedVpi, pwAtmOutboundNto1MappedVci } STATUS current DESCRIPTION "Collection of objects for N:1 or 1:1 ATM PW outbound config." ::= { pwAtmGroups 9 } pwAtmInboundNto1Group OBJECT-GROUP OBJECTS {pwAtmInboundNto1RowStatus, pwAtmInboundNto1TrafficParamDescr, pwAtmInboundNto1MappedVpi, pwAtmInboundNto1MappedVci } STATUS current DESCRIPTION "Collection of objects for N:1 or 1:1 ATM PW inbound config." ::= { pwAtmGroups 10 } END -- -- Copyright (C) The Internet Society (2006). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- -- Acknowledgment -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society.