-- extracted from draft-ietf-pwe3-cep-mib-04.txt -- at Wed Dec 24 06:16:16 2003 PW-CEP-DRAFT04-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Unsigned32, Counter64 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC InterfaceIndexOrZero, InterfaceIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB pwStdMIB FROM PW-TC-DRAFT04-MIB pwVcIndex FROM PW-DRAFT04-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB; -- The CEP MIB pwVcCepMIB MODULE-IDENTITY Danenberg et al Expires June 2004 7 Internet Draft PW CEP MIB December 2003 LAST-UPDATED "200311301200Z" -- November 30 2003 12:00:00 EST ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) Working Group" CONTACT-INFO " Dave Danenberg Postal: Litchfield Communications, Inc. 27 Princeton Rd Princeton Center West Watertown, CT 06795 Tel: 203-591-7062 Email: dave_danenberg@litchfieldcomm.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA 01824 Tel: 978-244-3051 Email: tnadeau@cisco.com David Zelig (Editor) Postal: Corrigent Systems LTD. 126, Yigal Alon St. Tel Aviv, ISRAEL Phone: +972-3-6945273 E-mail: davidz@corrigent.com Andrew G. Malis Postal: Tellabs, Inc. 2730 Orchard Parkway San Jose, CA 95134 Email: Andy.Malis@tellabs.com Ron Cohen Postal: Lycium Networks 2480 Sand Hill Road, Menlo-Park, CA 94025 Email: ronc@lyciumnetworks.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB contains managed object definitions for Circuit Emulation over Packet (CEP) as in: Malis, A., Prayson, P., Cohen, R. and Zelig, D. 'SONET/SDH Circuit Emulation Over Packet (CEP) encapsulation', Internet Draft . This MIB reports to the PW-STD-MIB as in: Zelig, D., Nadeau, T. 'Pseudo Wire (PW) Management Information Base'. The PW-STD-MIB contains structures and MIB associations generic to Pseudo-Wire (PW) emulation. PW-specific MIBs (such as this) contain config and stats for specific Danenberg et al Expires June 2004 8 Internet Draft PW CEP MIB December 2003 PW types. Copyright (C) The Internet Society (date). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. -- RFC Ed.: replace yyyy with actual RFC number & remove this note " -- Revision history. REVISION "200311301200Z" -- November 30 2003 12:00:00 EST DESCRIPTION "- Update description clause of main module. - Module Identity adapted to PWE3 tree. - Remove notifications (PW-STD-MIB now contains the PW level up/down notification). " REVISION "200310261200Z" -- 26 Oct 2003 12:00:00 EST DESCRIPTION "- Change pwVcCepFractTable to be rowCreated, and indexed by a virtual interface. Change the description in the main table to reflect this. " REVISION "200210231200Z" -- 23 Oct 2002 12:00:00 EST DESCRIPTION "- Added RTP header suppression config object. - Deleted jitter buffer rebuild objects. - Add VT and fractional SPE support. - Adding textual conventions. - Adding types to pwVcCepType. - Changind description of pwVcCepSonetIfIndex, pwVcCepSonetTimeSlot. - Adding badHdrStack as error code. - Change pwVcCepCfgNormalPktLength to pwVcCepSonetPayloadLength to more generally convey fractional SPE modes and VT modes. - Adding pwVcCepFracTable. " REVISION "200208161200Z" -- 16 Aug 2002 12:00:00 EST DESCRIPTION "- Updated to become IETF PWE3 working group doc. - Updated references to CEP draft." REVISION "200205291200Z" -- 29 May 2002 12:00:00 EST DESCRIPTION "- Renamed EsTimeStamp to LastErrorTimeStamp. Danenberg et al Expires June 2004 9 Internet Draft PW CEP MIB December 2003 - Renamed LastDefectsAtEs to LatchedIndications. - Renamed CurrentDefects to CurrentIndications. - Renamed defect indications (cepAis, cepRdi). - Renamed DBA bit settings (ais and unequipped). - Added objects: CfgJtrBfrResetOorange and CfgJtrBfrResetOorangeCnt. - Moved SONET Time Slot and Time Slot cfg error to CEP table from SONET extension table. Deleted SONET extension table. - Added Failure Counts (FCs) to stats tables. - Removed pwVcCepPerfCurrentTimeElapsed (it is a duplicate of pwVcCepTimeElapsed). - Removed 32-bit counters that were duplicates of 64-bit (HC) counters. - Other minor changes." REVISION "200202271200Z" -- 27 February 2002 12:00:00 EST DESCRIPTION "- Added objects pwVcCepTimeElapsed and pwVcCepValidIntervals for more accurate knowledge of interval data. - Changed pwVcCepCfgJtrBfrDepth units from packets to microseconds, and updated description. - Changed JtrBfrOoseqDropped to JtrBfrOoRngDropped (i.e, 'out of sequence' to 'out of range'). - Removed JtrBfrOverruns counter objects. This info is now contained within the JtrBfrOoRngDropped object. - Changed description of JtrBfrUnderrun. - Moved LastDefectsAtEs, LastEsTimeStamp, and DiscontinuityTime to the pwVcCepTable table. Removed them as conformance config objects. - Created new CurrentDefects in CepTable. - Added cepAis to and changed rdi to cepRdi (both are now in LastDefectsAtEs). Added note to cepAis - it must not (in itself) cause a cep down notification. - Changed the pwVcCepSonetExtTable to augment the sonetPathCurrentTable in RFC 2558. Imported sonetPathCurrentTable from the SONET-MIB. - Renamed PktResequence to PktReorder." REVISION "200111161200Z" -- 16 November 2001 12:00:00 EST DESCRIPTION "- Changed CEM to CEP. - Removed: 'unstructured' CEP type, ECC references, and signaling (CEP options) references, multiple VC instances references, and APS references. - Improved descriptions and some improved object names. - New conformance section. New ConformanceCfg table. - PktResequence is now read-only. Danenberg et al Expires June 2004 10 Internet Draft PW CEP MIB December 2003 - ConfMaxPktLength is now ConfNormalPktLength. - Replaced User Error Action with PlayOutValue. - New cfg object : consecutive non-SESs to exit UAS. - New cfg objects : elapsed time for stats intervals. - New stats object: summary packet error. - New object : added ConfigError to SonetExt table. - NOTE: Many objects added, deleted, or moved - so many OIDs have been re-ordered." REVISION "200109071200Z" -- 07 September 2001 12:00:00 EST DESCRIPTION "- Separated Top level Cfg objects from Total CEM stats. - Removed references to VC instances." REVISION "200107191200Z" -- 19 July 2001 12:00:00 EST DESCRIPTION "Based on the PWE3 Requirements/Framework, the original CEM MIB (draft-danenberg-sonet-ces-mpls-mib-00.txt) has Been split into 3 drafts: - PW-STD-MIB (Zelig, et al). Service-independent MIB. - PW-TC-STD-MIB (Nadeau, et al). Textual Conventions. - PW-CEP-STD-MIB (Danenberg, et al). Service-specific MIB. Aside from the split, then PW-CEM-MIB has undergone other changes: - Ability to define LOPS (loss of packet sync), SES and UAS. - Support for 'unstructured' operation. - Support for CEM-RDI. - Many more minor changes and clarifications." ::= { pwStdMIB 4 } --To be assigned by IANA -- Local Textual conventions PwVcCepCfgIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Index into the pwVcCepCfgTable." SYNTAX Unsigned32 PwVcCepSonetEbm ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3- sonet-vt used for fractional STS-1/VC-3. The EBM bits are the 28 least significant bits out of the 32 bit value" SYNTAX Unsigned32 Danenberg et al Expires June 2004 11 Internet Draft PW CEP MIB December 2003 PwVcCepSdhVc4Ebm ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3- sonet-vt used for each TUG-3 in fractional VC-4 circuits. The EBM bits are the 30 least significant bits out of the 32 bit value " SYNTAX Unsigned32 PwVcCepSonetVtgMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VT/VC types carried in the 7 VTG/TUG-2s. The format is 28 bits in the form of an Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3-sonet-vt used for fractional STS-1/VC-3. The mapping specifies the maximal occupancies of VT/VC within each VTG/TUG-2. For example, all four bits are set to 1 in this objects it represents a VTG carrying VT1.5s, while only three are set when VT2 are carried within this VTG. The relevant bits are the 28 least significant bits out of the 32 bit value." SYNTAX Unsigned32 PwVcCepFracAsyncMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of Asynchronous mapping carried inside STS-1, VC-3 or TUG-3 containing TU-3 circuit. The value of 'other' MUST be used if the Use of this object is not applicable." SYNTAX INTEGER { other ( 0), ds3 ( 1), e3 ( 2) } -- Top level components of this MIB module. -- Tables, Scalars pwVcCepObjects OBJECT IDENTIFIER ::= { pwVcCepMIB 1 } -- Conformance pwVcCepConformance OBJECT IDENTIFIER ::= { pwVcCepMIB 2 } -- CEP PW table pwVcCepTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepEntry Danenberg et al Expires June 2004 12 Internet Draft PW CEP MIB December 2003 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the index to the entry SONET path table for this CEP PW, and the index to the CEP config table." ::= { pwVcCepObjects 1 } pwVcCepEntry OBJECT-TYPE SYNTAX PwVcCepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This MIB reports to the PW-STD-MIB. This table is indexed by the same index that was created for the associated entry in the PW Table (in the PW-STD-MIB). - The PwVcIndex. An entry is created in this table by the agent for every entry in the pwVcTable with a pwVcType of 'cep'." INDEX { pwVcIndex } ::= { pwVcCepTable 1 } PwVcCepEntry ::= SEQUENCE { pwVcCepType INTEGER, pwVcCepSonetIfIndex InterfaceIndexOrZero, pwVcCepSonetTimeSlot Unsigned32, pwVcCepSonetConfigError BITS, pwVcCepCfgIndex PwVcCepCfgIndex, pwVcCepTimeElapsed Integer32, pwVcCepValidIntervals Integer32, pwVcCepCurrentIndications BITS, pwVcCepLatchedIndications BITS, pwVcCepLastEsTimeStamp TimeStamp, pwVcCepPeerCepOption Unsigned32 } pwVcCepType OBJECT-TYPE SYNTAX INTEGER { spe (1), vt (2), fracSpe (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the type of CEP PW. Currently only structured types are supported. Other CEP Types may be defined in the future. Danenberg et al Expires June 2004 13 Internet Draft PW CEP MIB December 2003 Currently supported CEP types are: 1 - spe : SONET STS-Nc signals. 2 - vt : SONET VT-x (x=1.5,2,3,6) signals. 3 - fracSpe : SONET fractional STS-1 or SDH fractional VC-3 or VC-4 carrying tributaries or Asynchronous signals. Support of vt and fracSpe is optional." DEFVAL { spe } ::= { pwVcCepEntry 1 } pwVcCepSonetIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This is a unique index within the ifTable. It represents the interface index for the SONET path for SPE emulation (RFC2558 section 3.3), an interface index for the SONET VT (RFC2558 section 3.4) if the VT to be emulated is extracted a SONET signal, or the ifIndex of the physical port emulated in VT mode if the VT to be emulated is directly feeded from a physical interface. It may represent an internal (virtual) interface if an NSP function exists between the physical interface and the emulation process. A value of zero indicates an interface index that has yet to be determined. Once set, if the SONET ifIndex is (for some reason) later removed, the agent MAY delete the associated PW rows (e.g., this pwVcCep table entry). If the agent does not delete the rows, it is recommended that the agent set this object to zero." ::= { pwVcCepEntry 2 } pwVcCepSonetTimeSlot OBJECT-TYPE SYNTAX Unsigned32 (1..192) MAX-ACCESS read-write STATUS current DESCRIPTION "In structured SPE CEP, this object indicates the starting time-slot for this SONET path within the SONET line and section. For OC-48, this value could range from 1 to 48. The SONET path width must be taken into consideration here. For example, in an OC-48, an STS-3c could not start at time-slot 47. In structured VT CEP, this object indicates the starting time slot for this tributary within the SONET path. For example, for VT1.5 tributary within STS-1, this value could range from 1 to 28." Danenberg et al Expires June 2004 14 Internet Draft PW CEP MIB December 2003 REFERENCE "RFC 2558, sonetPathCurrentWidth." ::= { pwVcCepEntry 3 } pwVcCepSonetConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), timeslotInUse ( 1), timeslotMisuse ( 2), peerDbaIncompatible ( 3), peerEbmIncompatible ( 4), peerRtpIncompatible ( 5), peerPidIncompatible ( 6), peerAsyncIncompatible ( 7) } MAX-ACCESS read-only STATUS current DESCRIPTION "timeslotInUse is when another CEP PW (via SONET ifIndex) has already reserved a timeslot(s) that this CEP PW is attempting to reserved. timeslotMisuse is set, for example, if specifying a starting timeslot of 45 for a SONET path of an STS-12c width. peerIncompatible bits are set if the local configuration is not compatible with the peer configuration as available from the CEP option received from the peer. for example if the remote is not capable of accepting DBA packets but the local node is configured to send DBA packets for this PW, peerDbaIncompatible will be set." ::= { pwVcCepEntry 4 } pwVcCepCfgIndex OBJECT-TYPE SYNTAX PwVcCepCfgIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Index to CEP configuration table below. It is likely that multiple CEP PWs will share 1 CEP Cfg table entry." ::= { pwVcCepEntry 5 } pwVcCepTimeElapsed OBJECT-TYPE SYNTAX Integer32 (1..900) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." ::= { pwVcCepEntry 6 } Danenberg et al Expires June 2004 15 Internet Draft PW CEP MIB December 2003 pwVcCepValidIntervals OBJECT-TYPE SYNTAX Integer32 (0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected. An agent with CEP capability must be capable of supporting at least n intervals. The minimum value of n is 4, The default of n is 32 and the maximum value of n is 96. The value will be unless the measurement was (re-) started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available. " ::= { pwVcCepEntry 7 } pwVcCepCurrentIndications OBJECT-TYPE SYNTAX BITS { missingPkt ( 0), ooRngDropped( 1), jtrBfrUnder ( 2), pktBadLength( 3), lops ( 4), cepRdi ( 5), cepAis ( 6), badHdrStack ( 7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Definitions: missingPkt - While playing out a sequence of packets, a packet(s) was determined to be missing based on a gap in the CEP sequence number. Note: If the implementation supports packet re-ordering, detecting gaps should not take place as packets arrive, only as they are played out - this gives time for mis-ordered packets to arrive late. ooRngDropped - Packet(s) arrives that is outside the range of the jitter buffer. This may be because the jitter buffer is full, or the sequence number addresses a buffer outside the current jitter buffer range, or addresses an already occupied buffer within range. Whether or not packet re-ordering is supported by the implementation, this indication MUST be supported. jtrBfrUnder - The jitter buffer underflowed due to not enough packets arriving as packets were being Danenberg et al Expires June 2004 16 Internet Draft PW CEP MIB December 2003 played out. pktBadLength - Non-bandwidth-saving packet arrives larger or smaller than pwVcCepCfgSonetPayloadLength, or when a fractional SPE packet length does not match the extension header or manual configuration indicating the number of equipped VTs. lops - Loss Of Packet Sync. See draft-ietf-pwe3-sonet. cepRdi - Circuit Emulation over Packet Remote Defect Indication. Generated by the remote CEP de-packetizer when detecting LOPS. Note: not generated by the remote SONET function. See draft-ietf-pwe3-sonet. cepAis - Remote CEP packetizer has detected AIS on its incoming SONET stream. See draft-ietf-pwe3- sonet. Note: cepAis MUST NOT (in itself) cause a CEP down notification. This would be a layer violation. badHdrStack - This indication is set when the number of CEP header extensions detected in incoming packets does not match the expected number. Note: currently there is no hierarchy of CEP defects. Note: the algorithm used to capture these indications is implementation specific." ::= { pwVcCepEntry 8 } pwVcCepLatchedIndications OBJECT-TYPE SYNTAX BITS { missingPkt ( 0), ooRngDropped( 1), jtrBfrUnder ( 2), pktBadLength( 3), lops ( 4), cepRdi ( 5), cepAis ( 6), badHdrStack ( 7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of CEP indicators when the CEP PW last declared an errored second (either as ES, SES or a second with errors inside a UAS) condition. At this time, only LOPS can create a failure. Since indicators other than LOPS are useful, all are latched here. For bit definitions, see pwVcCepCurrentIndications above. Note: the algorithm used to latch these indications when entering an defect state is implementation specific." Danenberg et al Expires June 2004 17 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepEntry 9 } pwVcCepLastEsTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which the CEP PW entered the ES or SES state." ::= { pwVcCepEntry 10 } pwVcCepPeerCepOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of CEP option parameter as received from the peer by the PW signaling protocol." ::= { pwVcCepEntry 11 } -- End of CEP PW table -- Obtain index for PW CEP Configuration table entries pwVcCepCfgIndexNext OBJECT-TYPE SYNTAX PwVcCepCfgIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for pwVcCepCfgIndex when creating entries in the pwVcCepCfgTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwVcCepCfgIndex for a new entry in the pwVcCepCfgTable, the manager issues a management protocol retrieval operation to obtain the current value of pwVcCepCfgIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { pwVcCepObjects 2 } -- PW CEP PW Configuration Table pwVcCepCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters that may be referenced by 1 or more CEP PWs by pwVcCepTable." Danenberg et al Expires June 2004 18 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepObjects 3 } pwVcCepCfgEntry OBJECT-TYPE SYNTAX PwVcCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "These parameters define the characteristics of a CEP PW. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many PWs." INDEX { pwVcCepCfgTableIndex } ::= { pwVcCepCfgTable 1 } PwVcCepCfgEntry ::= SEQUENCE { pwVcCepCfgTableIndex PwVcCepCfgIndex, pwVcCepConfigError BITS, pwVcCepSonetPayloadLength Unsigned32, pwVcCepCfgMinPktLength Unsigned32, pwVcCepCfgPktReorder TruthValue, pwVcCepCfgEnableDBA BITS, pwVcCepCfgRtpHdrSuppress TruthValue, pwVcCepCfgJtrBfrDepth Unsigned32, pwVcCepCfgConsecPktsInsync Unsigned32, pwVcCepCfgConsecMissingOutSync Unsigned32, pwVcCepCfgPktErrorPlayOutValue Unsigned32, pwVcCepCfgMissingPktsToSes Unsigned32, pwVcCepCfgSesToUas Unsigned32, pwVcCepCfgSecsToExitUas Unsigned32, pwVcCepCfgRowStatus RowStatus, pwVcCepCfgStorageType StorageType } pwVcCepCfgTableIndex OBJECT-TYPE SYNTAX PwVcCepCfgIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index to this table" ::= { pwVcCepCfgEntry 1 } pwVcCepConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), dba ( 1), lopsPktCount ( 2), Danenberg et al Expires June 2004 19 Internet Draft PW CEP MIB December 2003 pktLength ( 3), jtrBfrDepth ( 4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Various configurations errors. Illegal settings within the pwVcCepCfg or pwVcCepSonetExt tables." ::= { pwVcCepCfgEntry 2 } pwVcCepSonetPayloadLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The number of SONET bytes of the Path or VT carried as payload within one packet. For example, for STS-1 SPE circuits, value of 783 bytes indicates that each packet carries payload equivalent to one frame. For VT1.5 circuits, a payload length of 104 bytes indicates that each packet carries payload equivalent to one VT1.5 super-frame. The actual payload size may be different, due to bandwidth reduction modes, e.g. DBA mode or dynamically assigned fractional SPE. This length applies to inbound and outbound packets carrying user payload. Although there is no control over inbound packets, those of illegal length are discarded and accounted for (see pwVcCepPerf...PktsBadLength.) " REFERENCE "For use of payload bytes see Malis, A., et al, ." ::= { pwVcCepCfgEntry 3 } pwVcCepCfgMinPktLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This is the minimum CEP packet length in number of bytes (including CEP header and payload). It applies to CEP's bandwidth-savings packets. Currently DBA is the only bandwidth-savings packet type (in the future, CEP may support compression). Minimum packet length is necessary in some systems or networks. Setting Zero here indicates that there is no minimum packet restriction." DEFVAL { 0 } ::= { pwVcCepCfgEntry 4 } Danenberg et al Expires June 2004 20 Internet Draft PW CEP MIB December 2003 pwVcCepCfgPktReorder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set True: as inbound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequencing can occur) is dependant on the depth of the jitter buffer. See pwVcCepCfgJtrBfrDepth. NOTE: Some implementations may not support this feature. The agent is then required to set this False." ::= { pwVcCepCfgEntry 5 } pwVcCepCfgEnableDBA OBJECT-TYPE SYNTAX BITS { ais (0), unequipped (1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Bits set here MUST enable the DBA (dynamic bandwidth allocation) feature for the specified condition. Setting 'ais' MUST cause CEP packet payload suppression when AIS is detected on the associated SONET path. Similarly, 'unequipped' MUST cause payload suppression when an un-equipped condition is detected on the SONET path. During these conditions, CEP packets will continue to be sent, but with indicators set in the CEP header instructing the remote to play all ones (for AIS) or all zeros (for un-equipped) onto its SONET path. NOTE: Some implementations may not support this feature. In these cases, if the 'ais' or 'unequipped' bits are set, then 'dba' error code MUST be set in pwVcCepConfigError." REFERENCE "See Malis, A., et al, ." DEFVAL { { unequipped } } ::= { pwVcCepCfgEntry 6 } pwVcCepCfgRtpHdrSuppress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set True: an RTP header is not pre-pended to the CEP packet." Danenberg et al Expires June 2004 21 Internet Draft PW CEP MIB December 2003 REFERENCE "See Malis, A., et al, ." DEFVAL { false } ::= { pwVcCepCfgEntry 7 } pwVcCepCfgJtrBfrDepth OBJECT-TYPE SYNTAX Unsigned32 UNITS "micro-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This setting configures the number of microseconds of expected packet delay variation for this CEP PW over the PSN. The actual jitter buffer MUST be at least twice this value for proper operation, and is implementation specific. If configured to a value not supported by the implementation, the agent MUST return an error code 'jtrBfrDepth' in 'pwVcCepConfigError ' NOTE: Like bandwidth and time-slots, jitter buffers are a limited resource to be managed." ::= { pwVcCepCfgEntry 8 } -- -- The following counters work together to integrate (filter) -- errors and the lack of errors on the CEP PW. An error is -- caused by a missing packet. Missing packet can be a result -- of: packet loss in the network, (uncorrectable) packet out -- of sequence, packet length error, jitter buffer overflow, -- and jitter buffer underflow. The result is declaring whether -- or not the CEP PW is in Loss of Packet Sync (LOPS) state. -- pwVcCepCfgConsecPktsInsync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive pkts with sequential sequence numbers required to exit the LOPS state." REFERENCE "See Malis, A., et al, ." DEFVAL { 2 } ::= { pwVcCepCfgEntry 9 } pwVcCepCfgConsecMissingOutSync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive missing pkts required to enter Danenberg et al Expires June 2004 22 Internet Draft PW CEP MIB December 2003 the LOPS state." REFERENCE "See Malis, A., et al, ." DEFVAL { 10 } ::= { pwVcCepCfgEntry 10 } pwVcCepCfgPktErrorPlayOutValue OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the value played when inbound packets have over/underflowed the jitter buffer, or are missing for any reason. This byte pattern is sent (played) on the SONET path." DEFVAL { 255 } -- Play all ones ::= { pwVcCepCfgEntry 11 } pwVcCepCfgMissingPktsToSes OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Errored Second (SES) to be counted." DEFVAL { 3 } ::= { pwVcCepCfgEntry 12 } pwVcCepCfgSesToUas OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of consecutive SESs before declaring PW in UAS state (and at which point pwVcCepPerfUASs starts counting). The SesToUas default value is 10 seconds. NOTE: Similar to RFC 3592, If the agent chooses to update the various performance statistics in real time then it must be prepared to retroactively reduce the ES, SES, counts by this value and increase the UAS count by this value when it determines that UAS state has been entered. NOTE: See pwVcCepPerfSESs and pwVcCepPerfUASs." DEFVAL { 10 } ::= { pwVcCepCfgEntry 13 } pwVcCepCfgSecsToExitUas OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create Danenberg et al Expires June 2004 23 Internet Draft PW CEP MIB December 2003 STATUS current DESCRIPTION "Number of consecutive nonSESs before declaring PW is NOT in UAS state (and at which point pwVcCepPerfUASs stops counting)." DEFVAL { 10 } ::= { pwVcCepCfgEntry 14 } pwVcCepCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { pwVcCepCfgEntry 16 } pwVcCepCfgStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this row." ::= { pwVcCepCfgEntry 15 } -- End of CEP PW Configuration Parameter Table -- Fractional CEP Configuration Table pwVcCepFracTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters for CEP PWs with pwVcCepType FRAC type." ::= { pwVcCepObjects 4 } pwVcCepFracEntry OBJECT-TYPE SYNTAX PwVcCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of this table can be created in two options: - By the EMS in advance for creating the PW. - By the agent automatically when the PW is set up. The first option is typically used when there is an NSP cross-connect option between the physical ports and the emulated (virtual ports), while the second MAY be used when there is a one-to-one mapping between the emulated signal and the incoming signal. " INDEX { pwVcCepFracIndex } Danenberg et al Expires June 2004 24 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepFracTable 1 } PwVcCepFracEntry ::= SEQUENCE { pwVcCepFracIndex InterfaceIndex, pwVcCepFracMode INTEGER, pwVcCepFracConfigError BITS, pwVcCepFracAsync PwVcCepFracAsyncMap, pwVcCepFracVtgMap PwVcCepSonetVtgMap, pwVcCepFracEbm PwVcCepSonetEbm, pwVcCepFracPeerEbm PwVcCepSonetEbm, pwVcCepFracSdhVc4Mode INTEGER, pwVcCepFracSdhVc4Tu3Map1 PwVcCepFracAsyncMap, pwVcCepFracSdhVc4Tu3Map2 PwVcCepFracAsyncMap, pwVcCepFracSdhVc4Tu3Map3 PwVcCepFracAsyncMap, pwVcCepFracSdhVc4Tug2Map1 PwVcCepSonetVtgMap, pwVcCepFracSdhVc4Tug2Map2 PwVcCepSonetVtgMap, pwVcCepFracSdhVc4Tug2Map3 PwVcCepSonetVtgMap, pwVcCepFracSdhVc4Ebm1 PwVcCepSdhVc4Ebm, pwVcCepFracSdhVc4Ebm2 PwVcCepSdhVc4Ebm, pwVcCepFracSdhVc4Ebm3 PwVcCepSdhVc4Ebm, pwVcCepFracSdhVc4PeerEbm1 PwVcCepSdhVc4Ebm, pwVcCepFracSdhVc4PeerEbm2 PwVcCepSdhVc4Ebm, pwVcCepFracSdhVc4PeerEbm3 PwVcCepSdhVc4Ebm, pwVcCepFracRowStatus RowStatus, pwVcCepFracStorageType StorageType } pwVcCepFracIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the primary index of this table. It is a unique index within the ifTable. It represents the interface index for the SONET path (RFC 3592 section 3.3) for fractional SPE emulation. It may represent an internal (virtual) interface if an NSP function exists between the physical interface and the emulation process." ::= { pwVcCepFracEntry 1 } pwVcCepFracMode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 0), dynamic ( 1), static ( 2), staticWithEbm ( 3), staticAsync ( 4) Danenberg et al Expires June 2004 25 Internet Draft PW CEP MIB December 2003 } MAX-ACCESS read-create STATUS current DESCRIPTION "Fractional mode for STS-1/VC-3 circuits: notApplicable - When this is not STS-1/VC-3 signal. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from the payload on the fly. static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticAsync - Asynchronous E3/T3 fixed byte removal only. " DEFVAL { dynamic } ::= { pwVcCepFracEntry 2 } pwVcCepFracConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), vtgMapEbmconflict ( 1), vtgMapAsyncConflict ( 2) } MAX-ACCESS read-create STATUS current DESCRIPTION "vtgMapEbmConflict is set when the configured static EBM does not match the configured vtgMap for fractional STS-1/VC-3 circuits, or when the TUG2Map is in conflict with the static EBM for VC-4 circuits. For example, if the vtgMap specifies that VTG#1 carries VT2 VTs while the EBM indicate that four VTs are equipped within VTG#1. vtgMapAsyncConflict is set when there is a conflict between the mode, the async indication and the vtgMap fields. For example, fractional mode is set to Static Async while the VtgMap indicate that the STS-1/VC-3 carries VTs. Or in fractional VC-4 circuits both async1 and Tug2Map are set." ::= { pwVcCepFracEntry 3 } pwVcCepFracAsync OBJECT-TYPE SYNTAX PwVcCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "The Asynchronous payload carried within the STS-1/VC-3. This variable should be set when 'staticAsync' Fractional STS-1/VC-3 pwVcCepFracMode is selected, and hold the value of 'other' otherwise." Danenberg et al Expires June 2004 26 Internet Draft PW CEP MIB December 2003 DEFVAL { other } ::= { pwVcCepFracEntry 4 } pwVcCepFracVtgMap OBJECT-TYPE SYNTAX PwVcCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VT/VC types of the seven VTG/TUG-2 within the STS-1/VC-3. This variable should be set when 'dynamic', 'static' or 'staticWithEbm' Fractional STS-1/VC-3 pwVcCepFracMode is selected. " ::= { pwVcCepFracEntry 5 } pwVcCepFracEbm OBJECT-TYPE SYNTAX PwVcCepSonetEbm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for STS-1/VC-3 channel. This variable should be set when 'static' or 'staticWithEbm' Fractional STS-1/VC-3 pwVcCepFracMode is selected. " ::= { pwVcCepFracEntry 6 } pwVcCepFracPeerEbm OBJECT-TYPE SYNTAX PwVcCepSonetEbm MAX-ACCESS read-create STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for STS-1/VC-3 channel received from the peer within the CEP extension header." ::= { pwVcCepFracEntry 7 } pwVcCepFracSdhVc4Mode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 0), dynamic ( 1), static ( 2), staticWithEbm ( 3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Fractional mode for VC-4 circuits: notApllicable - When this is not VC-4 circuit. dynamic - EBM carried within the CEP header. Unequipped Danenberg et al Expires June 2004 27 Internet Draft PW CEP MIB December 2003 VTs are removed from the payload on the fly. static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. " DEFVAL { notApplicable } ::= { pwVcCepFracEntry 8 } pwVcCepFracSdhVc4Tu3Map1 OBJECT-TYPE SYNTAX PwVcCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the first TUG-3 within the VC-4 contains a TU-3, this variable must be set. " DEFVAL { other } ::= { pwVcCepFracEntry 9 } pwVcCepFracSdhVc4Tu3Map2 OBJECT-TYPE SYNTAX PwVcCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the second TUG-3 within the VC-4 contains a TU-3, this variable must be set." DEFVAL { other } ::= { pwVcCepFracEntry 10 } pwVcCepFracSdhVc4Tu3Map3 OBJECT-TYPE SYNTAX PwVcCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the third TUG-3 within the VC-4 contains a TU-3, this variable must be set. " DEFVAL { other } ::= { pwVcCepFracEntry 11 } pwVcCepFracSdhVc4Tug2Map1 OBJECT-TYPE SYNTAX PwVcCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the first TUG-3 of the VC-4. " Danenberg et al Expires June 2004 28 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepFracEntry 12 } pwVcCepFracSdhVc4Tug2Map2 OBJECT-TYPE SYNTAX PwVcCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the second TUG-3 of the VC-4. " ::= { pwVcCepFracEntry 13 } pwVcCepFracSdhVc4Tug2Map3 OBJECT-TYPE SYNTAX PwVcCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the third TUG-3 of the VC-4. " ::= { pwVcCepFracEntry 14 } pwVcCepFracSdhVc4Ebm1 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for first TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' Fractional VC-4 pwVcCepFracMode is selected. " ::= { pwVcCepFracEntry 15 } pwVcCepFracSdhVc4Ebm2 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for second TUG-3 within the VC-4. This variable should be set when 'static' or 'StaticWithEbm' Fractional VC-4 pwVcCepFracMode is selected. " ::= { pwVcCepFracEntry 16 } pwVcCepFracSdhVc4Ebm3 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for third TUG-3 within Danenberg et al Expires June 2004 29 Internet Draft PW CEP MIB December 2003 the VC-4. This variable should be set when 'Static' or 'staticWithEbm' Fractional VC-4 pwVcCepFracMode is selected. " ::= { pwVcCepFracEntry 17 } pwVcCepFracSdhVc4PeerEbm1 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the first TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwVcCepFracEntry 18 } pwVcCepFracSdhVc4PeerEbm2 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the second TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwVcCepFracEntry 19 } pwVcCepFracSdhVc4PeerEbm3 OBJECT-TYPE SYNTAX PwVcCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the third TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwVcCepFracEntry 20 } pwVcCepFracRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row." ::= { pwVcCepFracEntry 21 } pwVcCepFracStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current Danenberg et al Expires June 2004 30 Internet Draft PW CEP MIB December 2003 DESCRIPTION "This variable indicates the storage type for this object." ::= { pwVcCepFracEntry 22 } -- End Fractional CEP Configuration Table -- CEP PW Performance Current Interval Table. pwVcCepPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CEP bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation - and don't stop. In the SONET world, counts are kept in 15 minute intervals. The CEP-MIB supports both methods. The current 15 minute interval counts are in this table. The interval and total stats are in tables following this. This table provides per CEP PW performance information. HC (high capacity) counters are required for some counts due to the high speeds expected with CEP services. A SONET path of width 48 (STS-48c) can rollover non-HC counters in a few minutes." ::= { pwVcCepObjects 5 } pwVcCepPerfCurrentEntry OBJECT-TYPE SYNTAX PwVcCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwVcCep entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwVcCepPerfInterval table and the counts in this entry are reset to zero." INDEX { pwVcIndex } ::= { pwVcCepPerfCurrentTable 1 } PwVcCepPerfCurrentEntry ::= SEQUENCE { pwVcCepPerfCurrentDbaInPacketsHC Counter64, pwVcCepPerfCurrentDbaOutPacketsHC Counter64, pwVcCepPerfCurrentInNegPtrAdjust Counter32, pwVcCepPerfCurrentInPosPtrAdjust Counter32, pwVcCepPerfCurrentInPtrAdjustSecs Counter32, pwVcCepPerfCurrentOutNegPtrAdjust Counter32, Danenberg et al Expires June 2004 31 Internet Draft PW CEP MIB December 2003 pwVcCepPerfCurrentOutPosPtrAdjust Counter32, pwVcCepPerfCurrentOutPtrAdjustSecs Counter32, pwVcCepPerfCurrentAbsPtrAdjust Integer32, pwVcCepPerfCurrentMissingPkts Counter32, pwVcCepPerfCurrentPktsOoseq Counter32, pwVcCepPerfCurrentPktsOoRngDropped Counter32, pwVcCepPerfCurrentJtrBfrUnderruns Counter32, pwVcCepPerfCurrentPktsBadLength Counter32, pwVcCepPerfCurrentSummaryErrors Counter32, pwVcCepPerfCurrentESs PerfCurrentCount, pwVcCepPerfCurrentSESs PerfCurrentCount, pwVcCepPerfCurrentUASs PerfCurrentCount, pwVcCepPerfCurrentFC PerfCurrentCount } pwVcCepPerfCurrentDbaInPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwVcCepPerfCurrentEntry 1 } pwVcCepPerfCurrentDbaOutPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwVcCepPerfCurrentEntry 2 } -- Pointer adjustment stats pwVcCepPerfCurrentInNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfCurrentEntry 3 } pwVcCepPerfCurrentInPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfCurrentEntry 4 } Danenberg et al Expires June 2004 32 Internet Draft PW CEP MIB December 2003 pwVcCepPerfCurrentInPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path." ::= { pwVcCepPerfCurrentEntry 5 } pwVcCepPerfCurrentOutNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfCurrentEntry 6 } pwVcCepPerfCurrentOutPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfCurrentEntry 7 } pwVcCepPerfCurrentOutPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path." ::= { pwVcCepPerfCurrentEntry 8 } pwVcCepPerfCurrentAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust ) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwVcCepPerfCurrentEntry 9 } pwVcCepPerfCurrentMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header Danenberg et al Expires June 2004 33 Internet Draft PW CEP MIB December 2003 sequence number gaps)." ::= { pwVcCepPerfCurrentEntry 10 } pwVcCepPerfCurrentPktsOoseq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feature (see pwVcCepCfgPktReorder)." ::= { pwVcCepPerfCurrentEntry 11 } pwVcCepPerfCurrentPktsOoRngDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer." ::= { pwVcCepPerfCurrentEntry 12 } pwVcCepPerfCurrentJtrBfrUnderruns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwVcCepPerfCurrentEntry 13 } pwVcCepPerfCurrentPktsBadLength OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of normal (non-bandwidth-saving packets received) larger or smaller than pwVcCepCfgNormalPktLength." ::= { pwVcCepPerfCurrentEntry 14 } pwVcCepPerfCurrentSummaryErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwVcCepPerfCurrentEntry 15 } pwVcCepPerfCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount Danenberg et al Expires June 2004 34 Internet Draft PW CEP MIB December 2003 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwVcCepPerfCurrentEntry 16 } pwVcCepPerfCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwVcCepPerfCurrentEntry 17 } pwVcCepPerfCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwVcCepPerfCurrentEntry 18 } pwVcCepPerfCurrentFC OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwVcCepPerfCurrentEntry 19 } -- End CEP PW Performance Current Interval Table -- CEP PW Performance Interval Table. pwVcCepPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information much like the pwVcCepPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period, but is not limited to this. NOTE: Counter64 objects are used here, Counter32 is Danenberg et al Expires June 2004 35 Internet Draft PW CEP MIB December 2003 too small for OC-768 CEP PWs." ::= { pwVcCepObjects 6 } pwVcCepPerfIntervalEntry OBJECT-TYPE SYNTAX PwVcCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwVcCepPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval. pwVcCepIndex is found in the pwVcCepCfg table." INDEX { pwVcIndex, pwVcCepPerfIntervalNumber } ::= { pwVcCepPerfIntervalTable 1 } PwVcCepPerfIntervalEntry ::= SEQUENCE { pwVcCepPerfIntervalNumber Unsigned32, pwVcCepPerfIntervalValidData TruthValue, pwVcCepPerfIntervalReset INTEGER, pwVcCepPerfIntervalTimeElapsed Integer32, pwVcCepPerfIntervalDbaInPacketsHC Counter64, pwVcCepPerfIntervalDbaOutPacketsHC Counter64, pwVcCepPerfIntervalInNegPtrAdjust Counter32, pwVcCepPerfIntervalInPosPtrAdjust Counter32, pwVcCepPerfIntervalInPtrAdjustSecs Counter32, pwVcCepPerfIntervalOutNegPtrAdjust Counter32, pwVcCepPerfIntervalOutPosPtrAdjust Counter32, pwVcCepPerfIntervalOutPtrAdjustSecs Counter32, pwVcCepPerfIntervalAbsPtrAdjust Integer32, pwVcCepPerfIntervalMissingPkts Counter32, pwVcCepPerfIntervalPktsOoseq Counter32, pwVcCepPerfIntervalPktsOoRngDropped Counter32, pwVcCepPerfIntervalJtrBfrUnderruns Counter32, pwVcCepPerfIntervalPktsBadLength Counter32, pwVcCepPerfIntervalSummaryErrors Counter32, pwVcCepPerfIntervalESs PerfIntervalCount, pwVcCepPerfIntervalSESs PerfIntervalCount, pwVcCepPerfIntervalUASs PerfIntervalCount, pwVcCepPerfIntervalFC PerfIntervalCount } pwVcCepPerfIntervalNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION Danenberg et al Expires June 2004 36 Internet Draft PW CEP MIB December 2003 "A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96." ::= { pwVcCepPerfIntervalEntry 1 } pwVcCepPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwVcCepPerfIntervalEntry 2 } pwVcCepPerfIntervalReset OBJECT-TYPE SYNTAX INTEGER { reset (1), normal(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero." ::= { pwVcCepPerfIntervalEntry 3 } pwVcCepPerfIntervalTimeElapsed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { pwVcCepPerfIntervalEntry 4 } pwVcCepPerfIntervalDbaInPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwVcCepPerfIntervalEntry 5 } Danenberg et al Expires June 2004 37 Internet Draft PW CEP MIB December 2003 pwVcCepPerfIntervalDbaOutPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwVcCepPerfIntervalEntry 6 } -- Pointer adjustment stats pwVcCepPerfIntervalInNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfIntervalEntry 7 } pwVcCepPerfIntervalInPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfIntervalEntry 8 } pwVcCepPerfIntervalInPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path." ::= { pwVcCepPerfIntervalEntry 9 } pwVcCepPerfIntervalOutNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfIntervalEntry 10 } pwVcCepPerfIntervalOutPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfIntervalEntry 11 } Danenberg et al Expires June 2004 38 Internet Draft PW CEP MIB December 2003 pwVcCepPerfIntervalOutPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path." ::= { pwVcCepPerfIntervalEntry 12 } pwVcCepPerfIntervalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwVcCepPerfIntervalEntry 13 } pwVcCepPerfIntervalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwVcCepPerfIntervalEntry 14 } pwVcCepPerfIntervalPktsOoseq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations mat not support this feature (see pwVcCepCfgPktReorder)." ::= { pwVcCepPerfIntervalEntry 15 } pwVcCepPerfIntervalPktsOoRngDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer." ::= { pwVcCepPerfIntervalEntry 16 } pwVcCepPerfIntervalJtrBfrUnderruns OBJECT-TYPE SYNTAX Counter32 Danenberg et al Expires June 2004 39 Internet Draft PW CEP MIB December 2003 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwVcCepPerfIntervalEntry 17 } pwVcCepPerfIntervalPktsBadLength OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received larger or smaller than pwVcCepCfgNormalPktLength." ::= { pwVcCepPerfIntervalEntry 18 } pwVcCepPerfIntervalSummaryErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwVcCepPerfIntervalEntry 19 } pwVcCepPerfIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwVcCepPerfIntervalEntry 20 } pwVcCepPerfIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwVcCepPerfIntervalEntry 21 } pwVcCepPerfIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwVcCepPerfIntervalEntry 22 } pwVcCepPerfIntervalFC OBJECT-TYPE SYNTAX PerfIntervalCount Danenberg et al Expires June 2004 40 Internet Draft PW CEP MIB December 2003 MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwVcCepPerfIntervalEntry 23 } -- End CEP PW Performance Interval Table -- CEP PW Total Performance Table pwVcCepPerfTotalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information much like the pwVcCepPerfIntervalTable above. However, these counts represent complete historical information. NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEP PWs." ::= { pwVcCepObjects 7 } pwVcCepPerfTotalEntry OBJECT-TYPE SYNTAX PwVcCepPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in this table by the agent for every entry in the pwVcCep table." INDEX { pwVcIndex } ::= { pwVcCepPerfTotalTable 1 } PwVcCepPerfTotalEntry ::= SEQUENCE { pwVcCepPerfTotalDbaInPacketsHC Counter64, pwVcCepPerfTotalDbaOutPacketsHC Counter64, pwVcCepPerfTotalInNegPtrAdjust Counter32, pwVcCepPerfTotalInPosPtrAdjust Counter32, pwVcCepPerfTotalInPtrAdjustSecs Counter32, pwVcCepPerfTotalOutNegPtrAdjust Counter32, pwVcCepPerfTotalOutPosPtrAdjust Counter32, pwVcCepPerfTotalOutPtrAdjustSecs Counter32, pwVcCepPerfTotalAbsPtrAdjust Integer32, pwVcCepPerfTotalMissingPkts Counter32, Danenberg et al Expires June 2004 41 Internet Draft PW CEP MIB December 2003 pwVcCepPerfTotalPktsOoseq Counter32, pwVcCepPerfTotalPktsOoRngDropped Counter32, pwVcCepPerfTotalJtrBfrUnderruns Counter32, pwVcCepPerfTotalPktsBadLength Counter32, pwVcCepPerfTotalSummaryErrors Counter32, pwVcCepPerfTotalESs Counter32, pwVcCepPerfTotalSESs Counter32, pwVcCepPerfTotalUASs Counter32, pwVcCepPerfTotalFC Counter32, pwVcCepPerfTotalDiscontinuityTime TimeStamp } pwVcCepPerfTotalDbaInPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwVcCepPerfTotalEntry 1 } pwVcCepPerfTotalDbaOutPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwVcCepPerfTotalEntry 2 } -- Pointer adjustment stats pwVcCepPerfTotalInNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfTotalEntry 3 } pwVcCepPerfTotalInPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwVcCepPerfTotalEntry 4 } pwVcCepPerfTotalInPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Danenberg et al Expires June 2004 42 Internet Draft PW CEP MIB December 2003 "Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path." ::= { pwVcCepPerfTotalEntry 5 } pwVcCepPerfTotalOutNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfTotalEntry 6 } pwVcCepPerfTotalOutPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwVcCepPerfTotalEntry 7 } pwVcCepPerfTotalOutPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path." ::= { pwVcCepPerfTotalEntry 8 } pwVcCepPerfTotalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwVcCepPerfTotalEntry 9 } pwVcCepPerfTotalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwVcCepPerfTotalEntry 10 } pwVcCepPerfTotalPktsOoseq OBJECT-TYPE SYNTAX Counter32 Danenberg et al Expires June 2004 43 Internet Draft PW CEP MIB December 2003 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feature (see pwVcCepCfgPktReorder)." ::= { pwVcCepPerfTotalEntry 11 } pwVcCepPerfTotalPktsOoRngDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer." ::= { pwVcCepPerfTotalEntry 12 } pwVcCepPerfTotalJtrBfrUnderruns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwVcCepPerfTotalEntry 13 } pwVcCepPerfTotalPktsBadLength OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets received larger or smaller than pwVcCepCfgNormalPktLength." ::= { pwVcCepPerfTotalEntry 14 } pwVcCepPerfTotalSummaryErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwVcCepPerfTotalEntry 15 } pwVcCepPerfTotalESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered. See draft-ietf-pwe3-sonet for definition of ES." Danenberg et al Expires June 2004 44 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepPerfTotalEntry 16 } pwVcCepPerfTotalSESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds. See pwVcCepCfgMissingPktsToSes. Also see draft-ietf-pwe3-sonet for definition." ::= { pwVcCepPerfTotalEntry 17 } pwVcCepPerfTotalUASs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of UnAvailable Seconds. See pwVcCepCfgSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added to this object, then as each additional UAS occurs, this object increments by one. NOTE: Similar to RFC 2558, If the agent chooses to update the various performance statistics in real time then it must be prepared to retroactively reduce the ES, SES, counts (by the value of pwVcCepCfgSesToUas) and increase the UAS count (by that same value) when it determines that UAS state has been entered." ::= { pwVcCepPerfTotalEntry 18 } pwVcCepPerfTotalFC OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared." ::= { pwVcCepPerfTotalEntry 19 } pwVcCepPerfTotalDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value." Danenberg et al Expires June 2004 45 Internet Draft PW CEP MIB December 2003 ::= { pwVcCepPerfTotalEntry 20 } -- End of PW CEP Total Performance table -- Conformance Configuration table pwVcCepConformanceCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwVcCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the means for the agent to declare whether certain CEP PW statistics objects are supported (conformed to) or not. If not supported, then the object MUST be return 0." ::= { pwVcCepObjects 9 } pwVcCepConformanceCfgEntry OBJECT-TYPE SYNTAX PwVcCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The agent MUST create a single entry in this table." INDEX { pwVcCepConformanceCfgIndex } ::= { pwVcCepConformanceCfgTable 1 } PwVcCepConformanceCfgEntry ::= SEQUENCE { pwVcCepConformanceCfgIndex INTEGER, pwVcCepPerfDbaInPacketsHCTruth TruthValue, pwVcCepPerfDbaInPacketsHCDesc SnmpAdminString, pwVcCepPerfDbaOutPacketsHCTruth TruthValue, pwVcCepPerfDbaOutPacketsHCDesc SnmpAdminString, pwVcCepPerfPktsOoseqTruth TruthValue, pwVcCepPerfPktsOoseqDesc SnmpAdminString, pwVcCepPerfPktsOoRngDroppedTruth TruthValue, pwVcCepPerfPktsOoRngDroppedDesc SnmpAdminString, pwVcCepPerfSummaryErrorsTruth TruthValue, pwVcCepPerfSummaryErrorsDesc SnmpAdminString } pwVcCepConformanceCfgIndex OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION Danenberg et al Expires June 2004 46 Internet Draft PW CEP MIB December 2003 "Any arbitrary number" ::= { pwVcCepConformanceCfgEntry 1 } pwVcCepPerfDbaInPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwVcCepPerf...DbaInPacketsHC in the pwVcCepPerf...Table is supported." ::= { pwVcCepConformanceCfgEntry 2 } pwVcCepPerfDbaInPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwVcCepPerf...DbaInPacketsHC support in the pwVcCepPerf...Table." ::= { pwVcCepConformanceCfgEntry 3 } pwVcCepPerfDbaOutPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwVcCepPerf...DbaOutPacketsHC in the pwVcCepPerf...Table is supported." ::= { pwVcCepConformanceCfgEntry 4 } pwVcCepPerfDbaOutPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwVcCepPerf...DbaOutPacketsHC support in the pwVcCepPerf...Table." ::= { pwVcCepConformanceCfgEntry 5 } pwVcCepPerfPktsOoseqTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwVcCepPerf...PktsOoseq in the pwVcCepPerf...Table is supported." ::= { pwVcCepConformanceCfgEntry 6 } pwVcCepPerfPktsOoseqDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwVcCepPerf...PktsOoseq Danenberg et al Expires June 2004 47 Internet Draft PW CEP MIB December 2003 support in the pwVcCepPerf...Table." ::= { pwVcCepConformanceCfgEntry 7 } pwVcCepPerfPktsOoRngDroppedTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwVcCepPerf...PktsOoRngDropped in the pwVcCepPerf...Table is supported." ::= { pwVcCepConformanceCfgEntry 8 } pwVcCepPerfPktsOoRngDroppedDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwVcCepPerf...PktsOoRngDropped support in the pwVcCepPerf...Table." ::= { pwVcCepConformanceCfgEntry 9 } pwVcCepPerfSummaryErrorsTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwVcCepPerf...SummaryError in the pwVcCepPerf...Table is supported." ::= { pwVcCepConformanceCfgEntry 10 } pwVcCepPerfSummaryErrorsDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwVcCepPerf...SummaryError support in the pwVcCepPerf...Table." ::= { pwVcCepConformanceCfgEntry 11 } -- End of CEP PW Conformance Configuration table -- Conformance Information -- Note: Conformance at the object access and values level is -- still FFS, therefore current conformance is defined at the -- object existence level only. pwVcCepGroups OBJECT IDENTIFIER ::= { pwVcCepConformance 1 } pwVcCepCompliances OBJECT IDENTIFIER ::= { pwVcCepConformance 2 } pwCepModuleCompliance MODULE-COMPLIANCE Danenberg et al Expires June 2004 48 Internet Draft PW CEP MIB December 2003 STATUS current DESCRIPTION "The compliance statement for agent that support PW over CEP PSN operation." MODULE -- this module MANDATORY-GROUPS { pwVcCepGroup, pwVcCepCfgGroup, pwVcCepPerfCurrentGroup, pwVcCepPerfIntervalGroup, pwVcCepPerfTotalGroup, pwVcCepConformanceCfgGroup } ::= { pwVcCepCompliances 1 } -- Units of conformance. pwVcCepGroup OBJECT-GROUP OBJECTS { pwVcCepType, pwVcCepSonetIfIndex, pwVcCepSonetTimeSlot, pwVcCepSonetConfigError, pwVcCepCfgIndex, pwVcCepTimeElapsed, pwVcCepValidIntervals, pwVcCepCurrentIndications, pwVcCepLatchedIndications, pwVcCepLastEsTimeStamp, pwVcCepPeerCepOption } STATUS current DESCRIPTION "Collection of objects for basic CEP PW config and status." ::= { pwVcCepGroups 1 } pwVcCepCfgGroup OBJECT-GROUP OBJECTS { pwVcCepCfgIndexNext, pwVcCepConfigError, pwVcCepSonetPayloadLength, pwVcCepCfgMinPktLength, pwVcCepCfgPktReorder, pwVcCepCfgEnableDBA, pwVcCepCfgRtpHdrSuppress, pwVcCepCfgJtrBfrDepth, pwVcCepCfgConsecPktsInsync, Danenberg et al Expires June 2004 49 Internet Draft PW CEP MIB December 2003 pwVcCepCfgConsecMissingOutSync, pwVcCepCfgPktErrorPlayOutValue, pwVcCepCfgMissingPktsToSes, pwVcCepCfgSesToUas, pwVcCepCfgSecsToExitUas, pwVcCepCfgRowStatus, pwVcCepCfgStorageType } STATUS current DESCRIPTION "Collection of detailed objects needed to configure CEP PWs." ::= { pwVcCepGroups 2 } pwVcCepPerfCurrentGroup OBJECT-GROUP OBJECTS { pwVcCepPerfCurrentDbaInPacketsHC, pwVcCepPerfCurrentDbaOutPacketsHC, pwVcCepPerfCurrentInNegPtrAdjust, pwVcCepPerfCurrentInPosPtrAdjust, pwVcCepPerfCurrentInPtrAdjustSecs, pwVcCepPerfCurrentOutNegPtrAdjust, pwVcCepPerfCurrentOutPosPtrAdjust, pwVcCepPerfCurrentOutPtrAdjustSecs, pwVcCepPerfCurrentAbsPtrAdjust, pwVcCepPerfCurrentMissingPkts, pwVcCepPerfCurrentPktsOoseq, pwVcCepPerfCurrentPktsOoRngDropped, pwVcCepPerfCurrentJtrBfrUnderruns, pwVcCepPerfCurrentPktsBadLength, pwVcCepPerfCurrentSummaryErrors, pwVcCepPerfCurrentESs, pwVcCepPerfCurrentSESs, pwVcCepPerfCurrentUASs, pwVcCepPerfCurrentFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwVcCepGroups 3 } pwVcCepPerfIntervalGroup OBJECT-GROUP OBJECTS { pwVcCepPerfIntervalValidData, pwVcCepPerfIntervalReset, pwVcCepPerfIntervalTimeElapsed, Danenberg et al Expires June 2004 50 Internet Draft PW CEP MIB December 2003 pwVcCepPerfIntervalDbaInPacketsHC, pwVcCepPerfIntervalDbaOutPacketsHC, pwVcCepPerfIntervalInNegPtrAdjust, pwVcCepPerfIntervalInPosPtrAdjust, pwVcCepPerfIntervalInPtrAdjustSecs, pwVcCepPerfIntervalOutNegPtrAdjust, pwVcCepPerfIntervalOutPosPtrAdjust, pwVcCepPerfIntervalOutPtrAdjustSecs, pwVcCepPerfIntervalAbsPtrAdjust, pwVcCepPerfIntervalMissingPkts, pwVcCepPerfIntervalPktsOoseq, pwVcCepPerfIntervalPktsOoRngDropped, pwVcCepPerfIntervalJtrBfrUnderruns, pwVcCepPerfIntervalPktsBadLength, pwVcCepPerfIntervalSummaryErrors, pwVcCepPerfIntervalESs, pwVcCepPerfIntervalSESs, pwVcCepPerfIntervalUASs, pwVcCepPerfIntervalFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwVcCepGroups 4 } pwVcCepPerfTotalGroup OBJECT-GROUP OBJECTS { pwVcCepPerfTotalDbaInPacketsHC, pwVcCepPerfTotalDbaOutPacketsHC, pwVcCepPerfTotalInNegPtrAdjust, pwVcCepPerfTotalInPosPtrAdjust, pwVcCepPerfTotalInPtrAdjustSecs, pwVcCepPerfTotalOutNegPtrAdjust, pwVcCepPerfTotalOutPosPtrAdjust, pwVcCepPerfTotalOutPtrAdjustSecs, pwVcCepPerfTotalAbsPtrAdjust, pwVcCepPerfTotalMissingPkts, pwVcCepPerfTotalPktsOoseq, pwVcCepPerfTotalPktsOoRngDropped, pwVcCepPerfTotalJtrBfrUnderruns, pwVcCepPerfTotalPktsBadLength, pwVcCepPerfTotalSummaryErrors, pwVcCepPerfTotalESs, pwVcCepPerfTotalSESs, pwVcCepPerfTotalUASs, Danenberg et al Expires June 2004 51 Internet Draft PW CEP MIB December 2003 pwVcCepPerfTotalFC, pwVcCepPerfTotalDiscontinuityTime } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwVcCepGroups 5 } pwVcCepFracGroup OBJECT-GROUP OBJECTS { pwVcCepFracMode, pwVcCepFracConfigError, pwVcCepFracAsync, pwVcCepFracVtgMap, pwVcCepFracEbm, pwVcCepFracPeerEbm, pwVcCepFracSdhVc4Mode, pwVcCepFracSdhVc4Tu3Map1, pwVcCepFracSdhVc4Tu3Map2, pwVcCepFracSdhVc4Tu3Map3, pwVcCepFracSdhVc4Tug2Map1, pwVcCepFracSdhVc4Tug2Map2, pwVcCepFracSdhVc4Tug2Map3, pwVcCepFracSdhVc4Ebm1, pwVcCepFracSdhVc4Ebm2, pwVcCepFracSdhVc4Ebm3, pwVcCepFracSdhVc4PeerEbm1, pwVcCepFracSdhVc4PeerEbm2, pwVcCepFracSdhVc4PeerEbm3, pwVcCepFracRowStatus, pwVcCepFracStorageType } STATUS current DESCRIPTION "Collection of fractional SPE groups. These objects are optional and should be supported only if fractional SPE is supported within the network element. " ::= { pwVcCepGroups 6 } pwVcCepConformanceCfgGroup OBJECT-GROUP OBJECTS { pwVcCepPerfDbaInPacketsHCTruth, pwVcCepPerfDbaInPacketsHCDesc, pwVcCepPerfDbaOutPacketsHCTruth, pwVcCepPerfDbaOutPacketsHCDesc, pwVcCepPerfPktsOoseqTruth, pwVcCepPerfPktsOoseqDesc, pwVcCepPerfPktsOoRngDroppedTruth, pwVcCepPerfPktsOoRngDroppedDesc, Danenberg et al Expires June 2004 52 Internet Draft PW CEP MIB December 2003 pwVcCepPerfSummaryErrorsTruth, pwVcCepPerfSummaryErrorsDesc } STATUS current DESCRIPTION "Collection of objects declaring conformance to other objects." ::= { pwVcCepGroups 7 } END -- -- "Copyright (C) The Internet Society (2001). All Rights Reserved. This -- document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this -- document itself may not be modified in any way, such as by removing -- the copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of -- developing Internet standards in which case the procedures for -- copyrights defined in the Internet Standards process must be -- followed, or as required to translate it into languages other than -- English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- -- This document and the information contained herein is provided on an -- "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING -- TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING -- BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION -- HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF -- MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. --