-- extracted from draft-ietf-pwe3-cep-mib-06.txt -- at Thu Jul 21 06:35:15 2005 PW-CEP-STD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Unsigned32, Counter64 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC -- [RFC2579] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InterfaceIndexOrZero, InterfaceIndex FROM IF-MIB -- [RFC2863] PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB -- [RFC3593] HCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed, HCPerfValidIntervals FROM HC-PerfHist-TC-MIB -- [RFC3705] pwStdMIB -- RFC Ed.: replace yyyy with actual RFC number & remove this note FROM PW-TC-STD-MIB -- [RFCyyyy] pwIndex -- RFC Ed.: replace yyyy with actual RFC number & remove this note FROM PW-STD-MIB -- [RFCyyyy] Danenberg et al Expires February 2006 7 Internet Draft PW CEP MIB July 2005 ; -- The PW CEP MIB pwCepMIB MODULE-IDENTITY LAST-UPDATED "200507171200Z" -- 17 July 2005 12:00:00 GMT ORGANIZATION "Pseudo-Wire Emulation Edge-to-Edge (PWE3) Working Group" CONTACT-INFO " David Zelig (Ed.) E-mail: davidz@corrigent.com Ron Cohen (Ed.) Email: ronc@resolutenetworks.com Thomas D. Nadeau (Ed.) Email: tnadeau@cisco.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module contains managed object definitions for Circuit Emulation over Packet (CEP) as in: Malis, A., Prayson, P., Cohen, R. and Zelig, D. 'SONET/SDH Circuit Emulation Over Packet (CEP)', RFC yyyy -- RFC Ed.: replace yyyy with actual RFC number & remove this note Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. -- RFC Ed.: replace yyyy with actual RFC number & remove this note " ::= { pwStdMIB xxxx } -- To be assigned by IANA -- the value 5 is requested for this -- specific Module. -- Local Textual conventions PwCepCfgIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Index into the pwCepCfgTable." SYNTAX Unsigned32 PwCepSonetEbm ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Equipped Bit Mask (EBM) used for fractional STS-1/VC-3. The EBM bits are the 28 least significant bits out of the 32 bit value" Danenberg et al Expires February 2006 8 Internet Draft PW CEP MIB July 2005 SYNTAX Unsigned32 PwCepSdhVc4Ebm ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Equipped Bit Mask (EBM) used for each TUG-3 in fractional VC-4 circuits. The EBM bits are the 30 least significant bits out of the 32 bit value " SYNTAX Unsigned32 PwCepSonetVtgMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VT/VC types carried in the 7 VTG/TUG-2s. The format is 28 bits in the form of an Equipped Bit Mask (EBM) for fractional STS-1/VC-3. The mapping specifies the maximal occupancies of VT/VC within each VTG/TUG-2. For example, all four bits are set to 1 in this objects it represents a VTG carrying VT1.5/VC11s, while only three are set when VT2/VC12 are carried within this VTG. The relevant bits are the 28 least significant bits out of the 32 bit value." SYNTAX Unsigned32 PwCepFracAsyncMap ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of Asynchronous mapping carried inside STS-1, VC-3 or TUG-3 containing TU-3 circuit. The value of 'other' MUST be used if the Use of this object is not applicable." SYNTAX INTEGER { other ( 1), ds3 ( 2), e3 ( 3) } -- Top level components of this MIB module. -- Tables, Scalars pwCepObjects OBJECT IDENTIFIER ::= { pwCepMIB 1 } -- Conformance pwCepConformance OBJECT IDENTIFIER ::= { pwCepMIB 2 } -- CEP PW table pwCepTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepEntry MAX-ACCESS not-accessible STATUS current Danenberg et al Expires February 2006 9 Internet Draft PW CEP MIB July 2005 DESCRIPTION "This table contains objects and parameters for managing and monitoring the CEP PW." ::= { pwCepObjects 1 } pwCepEntry OBJECT-TYPE SYNTAX PwCepEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents the association of a SONET/SDH PATH or VT to a PW. This table is indexed by the pwIndex of the applicable PW entry in the pwTable. An entry is created in this table by the agent for every entry in the pwTable with a pwType of 'cep'." INDEX { pwIndex } ::= { pwCepTable 1 } PwCepEntry ::= SEQUENCE { pwCepType INTEGER, pwCepSonetIfIndex InterfaceIndexOrZero, pwCepSonetConfigErrorOrStatus BITS, pwCepCfgIndex PwCepCfgIndex, pwCepTimeElapsed HCPerfTimeElapsed, pwCepValidIntervals HCPerfValidIntervals, pwCepCurrentIndications BITS, pwCepLatchedIndications BITS, pwCepLastEsTimeStamp TimeStamp, pwCepPeerCepOption Unsigned32 } pwCepType OBJECT-TYPE SYNTAX INTEGER { spe (1), vt (2), fracSpe (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the sub-type of CEP PW. Currently only structured types are supported: 'spe'(1) : SONET STS-Nc signals. 'vt' (2) : SONET VT-x (x=1.5,2,3,6) signals. 'fracSpe' (3) : SONET fractional STS-1 or SDH fractional VC-3 or VC-4 carrying tributaries or Asynchronous signals. Support of 'vt' mode or 'fracSpe' mode is optional." Danenberg et al Expires February 2006 10 Internet Draft PW CEP MIB July 2005 DEFVAL { spe } ::= { pwCepEntry 1 } pwCepSonetIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This is a unique index within the ifTable. It represents the interface index for the SONET path for SPE emulation (RFC3593 section 3.3), an interface index for the SONET VT (RFC3593 section 3.4) if the VT to be emulated is extracted a SONET signal or locally mapped from a physical interface. A value of zero indicates an interface index that has yet to be determined. Once set, if the SONET ifIndex is (for some reason) later removed, the agent MAY delete the associated PW rows (e.g., this pwCep table entry). If the agent does not delete the rows, it is recommended that the agent set this object to zero." ::= { pwCepEntry 2 } pwCepSonetConfigErrorOrStatus OBJECT-TYPE SYNTAX BITS { other ( 0), timeslotInUse ( 1), timeslotMisuse ( 2), peerDbaIncompatible ( 3), -- Status Only peerEbmIncompatible ( 4), peerRtpIncompatible ( 5), peerPidIncompatible ( 6), peerAsyncIncompatible ( 7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object report a configuration mismatch inside the local node or between the local node and the peer node. Some bits indicate an error and some are simply a status report that does not affect the forwarding process. 'timeslotInUse'(1) is set when another CEP PW has already reserved a timeslot(s) that this CEP PW is attempting to reserved. 'timeslotMisuse'(2) is set when the stated timeslot this PW is trying to use is not legal. For example, if Danenberg et al Expires February 2006 11 Internet Draft PW CEP MIB July 2005 specifying a starting timeslot of 45 for a SONET path of an STS-12c width. The peerIncompatible bits are set if the local configuration is not compatible with the peer configuration as available from the CEP option received through the signaling process from the peer." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 11. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepEntry 3 } pwCepCfgIndex OBJECT-TYPE SYNTAX PwCepCfgIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Index to CEP configuration table below. Multiple CEP PWs MAY share a single pwCepCfgEntry." ::= { pwCepEntry 4 } pwCepTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value." ::= { pwCepEntry 5 } pwCepValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected. An agent with CEP capability must be capable of supporting at least n intervals. The minimum value of n is 4, The default of n is 32 and the maximum value of n is 96. " ::= { pwCepEntry 6 } pwCepCurrentIndications OBJECT-TYPE Danenberg et al Expires February 2006 12 Internet Draft PW CEP MIB July 2005 SYNTAX BITS { missingPkt ( 0), ooRngDropped( 1), jtrBfrUnder ( 2), pktBadLength( 3), lops ( 4), cepRdi ( 5), cepAis ( 6), badHdrStack ( 7), cepNeFailure( 8), cepFeFailure( 9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Definitions: 'missingPkt'(0) - While playing out a sequence of packets, a packet(s) was determined to be missing based on a gap in the CEP sequence number. Note: If the implementation supports packet re-ordering, detecting gaps should not take place as packets arrive, only as they are played out - this gives time for mis-ordered packets to arrive late. 'ooRngDropped'(1) - Packet(s) arrives that is outside the range of the jitter buffer. This may be because the jitter buffer is full, or the sequence number addresses a buffer outside the current jitter buffer range, or addresses an already occupied buffer within range. Whether or not packet re-ordering is supported by the implementation, this indication MUST be supported. 'jtrBfrUnder'(2) - The jitter buffer underflowed due to not enough packets arriving as packets were being played out. 'pktBadLength'(3) - Non-bandwidth-saving packet arrives larger or smaller than pwCepCfgSonetPayloadLength, or when a fractional SPE packet length does not match the extension header or manual configuration indicating the number of equipped VTs. 'lops'(4) - Loss Of Packet Synchronization. 'cepRdi'(5) - Circuit Emulation over Packet Remote Defect Indication. Generated by the remote CEP de-packetizer when detecting LOPS. Note: not generated by the remote SONET function. See draft-ietf-pwe3-sonet. 'cepAis'(6) - Remote CEP packetizer has detected AIS on its incoming SONET stream. Note: cepAis MUST NOT (in itself) cause a CEP down notification. 'badHdrStack'(7) - This indication is set when the number of Danenberg et al Expires February 2006 13 Internet Draft PW CEP MIB July 2005 CEP header extensions detected in incoming packets does not match the expected number. 'cepNeFailure'(8) - Set when CEP-NE failure is currenly declared. 'cepFeFailure'(8) - Set when CEP-FE failure is currenly declared. Note: currently there is no hierarchy of CEP defects. Note: the algorithm used to capture these indications is implementation specific." ::= { pwCepEntry 7 } pwCepLatchedIndications OBJECT-TYPE SYNTAX BITS { missingPkt ( 0), ooRngDropped( 1), jtrBfrUnder ( 2), pktBadLength( 3), lops ( 4), cepRdi ( 5), cepAis ( 6), badHdrStack ( 7), cepNeFailure( 8), cepFeFailure( 9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of CEP indicators when the CEP PW last declared errored second (either as ES, SES or a second with errors inside a UAS) condition. At this time, only LOPS can create a failure. Since indicators other than LOPS are useful, all are latched here. For bit definitions, see pwCepCurrentIndications above. Note: the algorithm used to latch these indications when entering an defect state is implementation specific." ::= { pwCepEntry 8 } pwCepLastEsTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which the CEP PW entered the ES or SES state." ::= { pwCepEntry 9 } Danenberg et al Expires February 2006 14 Internet Draft PW CEP MIB July 2005 pwCepPeerCepOption OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of CEP option parameter as received from the peer by the PW signaling protocol." ::= { pwCepEntry 10 } -- End of CEP PW table -- Obtain index for PW CEP Configuration table entries pwCepCfgIndexNext OBJECT-TYPE SYNTAX PwCepCfgIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for pwCepCfgIndex when creating entries in the pwCepCfgTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwCepCfgIndex for a new entry in the pwCepCfgTable, the manager issues a management protocol retrieval operation to obtain the current value of pwCepCfgIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { pwCepObjects 2 } -- PW CEP PW Configuration Table pwCepCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters that may be referenced by one or more CEP PWs by pwCepTable." ::= { pwCepObjects 3 } pwCepCfgEntry OBJECT-TYPE SYNTAX PwCepCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "These parameters define the characteristics of a Danenberg et al Expires February 2006 15 Internet Draft PW CEP MIB July 2005 CEP PW. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many PWs." INDEX { pwCepCfgTableIndex } ::= { pwCepCfgTable 1 } PwCepCfgEntry ::= SEQUENCE { pwCepCfgTableIndex PwCepCfgIndex, pwCepConfigError BITS, pwCepSonetPayloadLength Unsigned32, pwCepCfgMinPktLength Unsigned32, pwCepCfgPktReorder TruthValue, pwCepCfgEnableDBA BITS, pwCepCfgRtpHdrSuppress TruthValue, pwCepCfgJtrBfrDepth Unsigned32, pwCepCfgConsecPktsInsync Unsigned32, pwCepCfgConsecMissingOutSync Unsigned32, pwCepCfgPktErrorPlayOutValue Unsigned32, pwCepCfgMissingPktsToSes Unsigned32, pwCepCfgSesToUas Unsigned32, pwCepCfgSecsToExitUas Unsigned32, pwCepCfgRowStatus RowStatus, pwCepCfgStorageType StorageType } pwCepCfgTableIndex OBJECT-TYPE SYNTAX PwCepCfgIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index to this table" ::= { pwCepCfgEntry 1 } pwCepConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), dba ( 1), lopsPktCount ( 2), pktLength ( 3), jtrBfrDepth ( 4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Various configurations errors, detected when a configured Danenberg et al Expires February 2006 16 Internet Draft PW CEP MIB July 2005 value within the pwCepCfg or pwCepSonetExt tables cannot be supported by the local agent." ::= { pwCepCfgEntry 2 } pwCepSonetPayloadLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The number of SONET bytes of the Path or VT carried as payload within one packet. For example, for STS-1/VC-3 SPE circuits, value of 783 bytes indicates that each packet carries payload equivalent to one frame. For VT1.5/VC11 circuits, a payload length of 104 bytes indicates that each packet carries payload equivalent to one VT1.5 super-frame. The actual payload size may be different, due to bandwidth reduction modes, e.g. DBA mode or dynamically assigned fractional SPE. This length applies to inbound and outbound packets carrying user payload. Although there is no control over inbound packets, those of illegal length are discarded and accounted for (see pwCepPerf...PktsBadLength.) The default values are determined by the pwCepType: 783 for pwCepType equal spe(2) or fracSpe(3). For vt(3) modes, the applicable super-frame payload size is the default value. " REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, sections 4.1 and 10.2" -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepCfgEntry 3 } pwCepCfgMinPktLength OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This is the minimum CEP packet length in number of bytes (including CEP header and payload). It applies to CEP's bandwidth-savings packets. Currently DBA is the only bandwidth-savings packet type (in the future, CEP may support compression). Minimum packet length is necessary in some systems or networks. Setting Zero here indicates that there is no minimum packet restriction." DEFVAL { 0 } Danenberg et al Expires February 2006 17 Internet Draft PW CEP MIB July 2005 ::= { pwCepCfgEntry 4 } pwCepCfgPktReorder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If set 'true': as inbound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequencing can occur) is dependant on the depth of the jitter buffer. If the local agent support packet re-ordering, the default value SHOULD be set to 'true', Otherwise, this value SHOULD be set to 'false'." ::= { pwCepCfgEntry 5 } pwCepCfgEnableDBA OBJECT-TYPE SYNTAX BITS { ais (0), unequipped (1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Bits set here MUST enable the DBA (dynamic bandwidth allocation) feature for the specified condition. Setting 'ais' MUST cause CEP packet payload suppression when AIS is detected on the associated SONET path. Similarly, 'unequipped' MUST cause payload suppression when an un-equipped condition is detected on the SONET/SDH PATH/VT. During these conditions, CEP packets will continue to be sent, but with indicators set in the CEP header instructing the remote to play all ones (for AIS) or all zeros (for un-equipped) onto its SONET path. NOTE: Some implementations may not support this feature. In these cases, this object should be read-only." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 10. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark ::= { pwCepCfgEntry 6 } pwCepCfgRtpHdrSuppress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create Danenberg et al Expires February 2006 18 Internet Draft PW CEP MIB July 2005 STATUS current DESCRIPTION "If set True: an RTP header is not pre-pended to the CEP packet." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 4.3. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { false } ::= { pwCepCfgEntry 7 } pwCepCfgJtrBfrDepth OBJECT-TYPE SYNTAX Unsigned32 UNITS "micro-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This setting configures the number of microseconds of expected packet delay variation for this CEP PW over the PSN. The actual jitter buffer MUST be at least twice this value for proper operation, and is implementation specific. If configured to a value not supported by the implementation, the agent MUST return an error code 'jtrBfrDepth' in 'pwCepConfigError'." ::= { pwCepCfgEntry 8 } -- -- The following counters work together to integrate (filter) -- errors and the lack of errors on the CEP PW. An error is -- caused by a missing packet. Missing packet can be a result -- of: packet loss in the network, (uncorrectable) packet out -- of sequence, packet length error, jitter buffer overflow, -- and jitter buffer underflow. The result is declaring whether -- or not the CEP PW is in Loss of Packet Sync (LOPS) state. -- pwCepCfgConsecPktsInsync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive pkts with sequential sequence numbers required to exit the LOPS state." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 5.2.2. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark Danenberg et al Expires February 2006 19 Internet Draft PW CEP MIB July 2005 DEFVAL { 2 } ::= { pwCepCfgEntry 9 } pwCepCfgConsecMissingOutSync OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "Consecutive missing pkts required to enter the LOPS state." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 5.2.2. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 10 } pwCepCfgPktErrorPlayOutValue OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the value played when inbound packets have over/underflowed the jitter buffer, or are missing for any reason. This byte pattern is sent (played) on the SONET path." DEFVAL { 255 } -- Play all ones, equal to AIS indications. ::= { pwCepCfgEntry 11 } pwCepCfgMissingPktsToSes OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Errored Second (SES) to be counted." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 3 } ::= { pwCepCfgEntry 12 } pwCepCfgSesToUas OBJECT-TYPE SYNTAX Unsigned32 Danenberg et al Expires February 2006 20 Internet Draft PW CEP MIB July 2005 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of consecutive SESs before declaring PW in UAS state (and at which point pwCepPerfUASs starts counting). The SesToUas default value is 10 seconds. NOTE: Similar to RFC 3592, If the agent chooses to update the various performance statistics in real time then it must be prepared to retroactively reduce the ES, SES, counts by this value and increase the UAS count by this value when it determines that UAS state has been entered. NOTE: See pwCepPerfSESs and pwCepPerfUASs." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 13 } pwCepCfgSecsToExitUas OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Number of consecutive nonSESs before declaring PW is NOT in UAS state (and at which point pwCepPerfUASs stops counting)." REFERENCE "Malis, A., et al, 'SONET/SDH Circuit Emulation over Packet (CEP), RFC yyyy, section 9.1. " -- RFC Editor: Please replace yyyy with the RFC number and remove -- this remark DEFVAL { 10 } ::= { pwCepCfgEntry 14 } pwCepCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. None of the read-create objects values can be changed when pwCepCfgRowStatus is in the active(1) state. Changes are allowed when the pwRowStatus is in notInService(2) or notReady(3) states only. Danenberg et al Expires February 2006 21 Internet Draft PW CEP MIB July 2005 If the operator need to change one of the values for an active row (for example in order to fix a mismatch in configuration between the local node and the peer), the pwCepCfgRowStatus should be first changed to notInService(2), the objects may be changed now, and later to active(1) in order to re-initiate the signaling process with the new values in effect. Change of status from the active(1) state or deleting a row SHOULD be blocked by the local agent if the row is referenced by any pwCepEntry those pwRowStatus is in the active(1) state." ::= { pwCepCfgEntry 16 } pwCepCfgStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this row." ::= { pwCepCfgEntry 15 } -- End of CEP PW Configuration Parameter Table -- Fractional CEP Configuration Table pwCepFracTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains a set of parameters for CEP PWs with pwCepType FRAC type." ::= { pwCepObjects 4 } pwCepFracEntry OBJECT-TYPE SYNTAX PwCepFracEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of this table can be created in two options: - By the EMS in advance for creating the PW. - By the agent automatically when the PW is set up. The first option is typically used when there is an NSP cross-connect option between the physical ports and the emulated (virtual ports), while the second MAY be used when there is a one-to-one mapping between the emulated signal and the physical signal. " INDEX { pwCepFracIndex } Danenberg et al Expires February 2006 22 Internet Draft PW CEP MIB July 2005 ::= { pwCepFracTable 1 } PwCepFracEntry ::= SEQUENCE { pwCepFracIndex InterfaceIndex, pwCepFracMode INTEGER, pwCepFracConfigError BITS, pwCepFracAsync PwCepFracAsyncMap, pwCepFracVtgMap PwCepSonetVtgMap, pwCepFracEbm PwCepSonetEbm, pwCepFracPeerEbm PwCepSonetEbm, pwCepFracSdhVc4Mode INTEGER, pwCepFracSdhVc4Tu3Map1 PwCepFracAsyncMap, pwCepFracSdhVc4Tu3Map2 PwCepFracAsyncMap, pwCepFracSdhVc4Tu3Map3 PwCepFracAsyncMap, pwCepFracSdhVc4Tug2Map1 PwCepSonetVtgMap, pwCepFracSdhVc4Tug2Map2 PwCepSonetVtgMap, pwCepFracSdhVc4Tug2Map3 PwCepSonetVtgMap, pwCepFracSdhVc4Ebm1 PwCepSdhVc4Ebm, pwCepFracSdhVc4Ebm2 PwCepSdhVc4Ebm, pwCepFracSdhVc4Ebm3 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm1 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm2 PwCepSdhVc4Ebm, pwCepFracSdhVc4PeerEbm3 PwCepSdhVc4Ebm, pwCepFracRowStatus RowStatus, pwCepFracStorageType StorageType } pwCepFracIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the primary index of this table. It is a unique index within the ifTable. It represents the interface index for the SONET path (RFC 3592 section 3.3) for fractional SPE emulation. It may represent an internal (virtual) interface if an NSP function exists between the physical interface and the emulation process." ::= { pwCepFracEntry 1 } pwCepFracMode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 1), dynamic ( 2), static ( 3), staticWithEbm ( 4), staticAsync ( 5) } Danenberg et al Expires February 2006 23 Internet Draft PW CEP MIB July 2005 MAX-ACCESS read-create STATUS current DESCRIPTION "Fractional mode for STS-1/VC-3 or VC-4 circuits: notApplicable - When this object is not applicable. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from the payload on the fly. static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticAsync - Asynchronous E3/T3 fixed byte removal only. " DEFVAL { dynamic } ::= { pwCepFracEntry 2 } pwCepFracConfigError OBJECT-TYPE SYNTAX BITS { other ( 0), vtgMapEbmConflict ( 1), vtgMapAsyncConflict ( 2) } MAX-ACCESS read-only STATUS current DESCRIPTION "vtgMapEbmConflict is set when the configured static EBM does not match the configured vtgMap for fractional STS-1/VC-3 circuits, or when the TUG2Map is in conflict with the static EBM for VC-4 circuits. For example, if the vtgMap specifies that VTG#1 carries VT2 VTs while the EBM indicate that four VTs are equipped within VTG#1. vtgMapAsyncConflict is set when there is a conflict between the mode, the async indication and the vtgMap fields. For example, fractional mode is set to Static Async while the VtgMap indicate that the STS-1/VC-3 carries VTs. Or in fractional VC-4 circuits both async1 and Tug2Map are set." ::= { pwCepFracEntry 3 } pwCepFracAsync OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "The Asynchronous payload carried within the STS-1/VC-3. This variable should be set when 'staticAsync' Fractional STS-1/VC-3 pwCepFracMode is selected, and hold the value of 'other' otherwise." DEFVAL Danenberg et al Expires February 2006 24 Internet Draft PW CEP MIB July 2005 { other } ::= { pwCepFracEntry 4 } pwCepFracVtgMap OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VT/VC types of the seven VTG/TUG-2 within the STS-1/VC-3. This variable should be set when 'dynamic', 'static' or 'staticWithEbm' Fractional STS-1/VC-3 pwCepFracMode is selected. " ::= { pwCepFracEntry 5 } pwCepFracEbm OBJECT-TYPE SYNTAX PwCepSonetEbm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for STS-1/VC-3 channel. This variable MAY be set when 'static' or 'staticWithEbm' Fractional STS-1/VC-3 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 6 } pwCepFracPeerEbm OBJECT-TYPE SYNTAX PwCepSonetEbm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for STS-1/VC-3 channel received from the peer within the CEP extension header." ::= { pwCepFracEntry 7 } pwCepFracSdhVc4Mode OBJECT-TYPE SYNTAX INTEGER { notApplicable ( 1), dynamic ( 2), static ( 3), staticWithEbm ( 4) } MAX-ACCESS read-create STATUS current DESCRIPTION Danenberg et al Expires February 2006 25 Internet Draft PW CEP MIB July 2005 "Fractional mode for VC-4 circuits: notApllicable - When this is not VC-4 circuit. dynamic - EBM carried within the CEP header. Unequipped VTs are removed from the payload on the fly. static - EBM not carried within the CEP header. Only VTs defined in the EBM are carried within the payload. staticWithEbm - EBM carried within the CEP header. Only VTs defined in the EBM are carried within the payload. " DEFVAL { notApplicable } ::= { pwCepFracEntry 8 } pwCepFracSdhVc4Tu3Map1 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the first TUG-3 within the VC-4 contains a TU-3, this variable must be set to the required mode. " DEFVAL { other } ::= { pwCepFracEntry 9 } pwCepFracSdhVc4Tu3Map2 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the second TUG-3 within the VC-4 contains a TU-3, this variable must be set." DEFVAL { other } ::= { pwCepFracEntry 10 } pwCepFracSdhVc4Tu3Map3 OBJECT-TYPE SYNTAX PwCepFracAsyncMap MAX-ACCESS read-create STATUS current DESCRIPTION "If the third TUG-3 within the VC-4 contains a TU-3, this variable must be set. " DEFVAL { other } Danenberg et al Expires February 2006 26 Internet Draft PW CEP MIB July 2005 ::= { pwCepFracEntry 11 } pwCepFracSdhVc4Tug2Map1 OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the first TUG-3 of the VC-4. " ::= { pwCepFracEntry 12 } pwCepFracSdhVc4Tug2Map2 OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the second TUG-3 of the VC-4. " ::= { pwCepFracEntry 13 } pwCepFracSdhVc4Tug2Map3 OBJECT-TYPE SYNTAX PwCepSonetVtgMap MAX-ACCESS read-create STATUS current DESCRIPTION "The VC types of the seven TUG-2 within the third TUG-3 of the VC-4. " ::= { pwCepFracEntry 14 } pwCepFracSdhVc4Ebm1 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for first TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 15 } pwCepFracSdhVc4Ebm2 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-create Danenberg et al Expires February 2006 27 Internet Draft PW CEP MIB July 2005 STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for second TUG-3 within the VC-4. This variable should be set when 'static' or 'StaticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 16 } pwCepFracSdhVc4Ebm3 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-create STATUS current DESCRIPTION "Static Equipped Bit Mask (EBM) for third TUG-3 within the VC-4. This variable should be set when 'Static' or 'staticWithEbm' Fractional VC-4 pwCepFracMode is selected. It is possible that the EBM that would be used is available based on configuration of other MIB modules. In these cases this object is read-only and reflects the actual EBM that would be used." ::= { pwCepFracEntry 17 } pwCepFracSdhVc4PeerEbm1 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the first TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 18 } pwCepFracSdhVc4PeerEbm2 OBJECT-TYPE SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the second TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 19 } pwCepFracSdhVc4PeerEbm3 OBJECT-TYPE Danenberg et al Expires February 2006 28 Internet Draft PW CEP MIB July 2005 SYNTAX PwCepSdhVc4Ebm MAX-ACCESS read-only STATUS current DESCRIPTION "Equipped Bit Mask (EBM) for the third TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header." ::= { pwCepFracEntry 20 } pwCepFracRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. It is allowed to make changes to read-create entries in this table, but the operator should be aware that such changes for an active row may cause temporary mis-configurations between the peers in terms of the carried signal,leading to traffic distruption." ::= { pwCepFracEntry 21 } pwCepFracStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { pwCepFracEntry 22 } -- End Fractional CEP Configuration Table -- CEP PW Performance Current Interval Table. pwCepPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "CEP bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation - and don't stop. In the SONET world, counts are kept in 15 minute intervals. The PW CEP MIB supports both methods. The current 15 minute interval counts are in this table. The interval and total stats are in tables following this. Danenberg et al Expires February 2006 29 Internet Draft PW CEP MIB July 2005 This table provides per CEP PW performance information. HC (high capacity) counters are required for some counts due to the high speeds expected with CEP services. A SONET path of width 48 (STS-48c) can rollover non-HC counters in a few minutes." ::= { pwCepObjects 5 } pwCepPerfCurrentEntry OBJECT-TYPE SYNTAX PwCepPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwCep entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwCepPerfInterval table and the counts in this entry are reset to zero." INDEX { pwIndex } ::= { pwCepPerfCurrentTable 1 } PwCepPerfCurrentEntry ::= SEQUENCE { pwCepPerfCurrentDbaInPacketsHC HCPerfCurrentCount, pwCepPerfCurrentDbaOutPacketsHC HCPerfCurrentCount, pwCepPerfCurrentInNegPtrAdjust PerfCurrentCount, pwCepPerfCurrentInPosPtrAdjust PerfCurrentCount, pwCepPerfCurrentInPtrAdjustSecs PerfCurrentCount, pwCepPerfCurrentOutNegPtrAdjust PerfCurrentCount, pwCepPerfCurrentOutPosPtrAdjust PerfCurrentCount, pwCepPerfCurrentOutPtrAdjustSecs PerfCurrentCount, pwCepPerfCurrentAbsPtrAdjust Integer32, pwCepPerfCurrentMissingPkts PerfCurrentCount, pwCepPerfCurrentPktsOoseq PerfCurrentCount, pwCepPerfCurrentPktsOoRngDropped PerfCurrentCount, pwCepPerfCurrentJtrBfrUnderruns PerfCurrentCount, pwCepPerfCurrentPktsMalformed PerfCurrentCount, pwCepPerfCurrentSummaryErrors PerfCurrentCount, pwCepPerfCurrentESs PerfCurrentCount, pwCepPerfCurrentSESs PerfCurrentCount, pwCepPerfCurrentUASs PerfCurrentCount, pwCepPerfCurrentFC PerfCurrentCount } pwCepPerfCurrentDbaInPacketsHC OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerfCurrentEntry 1 } Danenberg et al Expires February 2006 30 Internet Draft PW CEP MIB July 2005 pwCepPerfCurrentDbaOutPacketsHC OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerfCurrentEntry 2 } -- Pointer adjustment stats pwCepPerfCurrentInNegPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfCurrentEntry 3 } pwCepPerfCurrentInPosPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfCurrentEntry 4 } pwCepPerfCurrentInPtrAdjustSecs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path." ::= { pwCepPerfCurrentEntry 5 } pwCepPerfCurrentOutNegPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfCurrentEntry 6 } pwCepPerfCurrentOutPosPtrAdjust OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the Danenberg et al Expires February 2006 31 Internet Draft PW CEP MIB July 2005 SONET path and encoded onto sent CEP packets." ::= { pwCepPerfCurrentEntry 7 } pwCepPerfCurrentOutPtrAdjustSecs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path." ::= { pwCepPerfCurrentEntry 8 } pwCepPerfCurrentAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust ) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerfCurrentEntry 9 } pwCepPerfCurrentMissingPkts OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwCepPerfCurrentEntry 10 } pwCepPerfCurrentPktsOoseq OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerfCurrentEntry 11 } pwCepPerfCurrentPktsOoRngDropped OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer." ::= { pwCepPerfCurrentEntry 12 } Danenberg et al Expires February 2006 32 Internet Draft PW CEP MIB July 2005 pwCepPerfCurrentJtrBfrUnderruns OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerfCurrentEntry 13 } pwCepPerfCurrentPktsMalformed OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerfCurrentEntry 14 } pwCepPerfCurrentSummaryErrors OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwCepPerfCurrentEntry 15 } pwCepPerfCurrentESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerfCurrentEntry 16 } pwCepPerfCurrentSESs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwCepPerfCurrentEntry 17 } pwCepPerfCurrentUASs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwCepPerfCurrentEntry 18 } Danenberg et al Expires February 2006 33 Internet Draft PW CEP MIB July 2005 pwCepPerfCurrentFC OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwCepPerfCurrentEntry 19 } -- End CEP PW Performance Current Interval Table -- CEP PW Performance Interval Table. pwCepPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information much like the pwCepPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period, but is not limited to this. NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEP PWs." ::= { pwCepObjects 6 } pwCepPerfIntervalEntry OBJECT-TYPE SYNTAX PwCepPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every pwCepPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval. pwCepIndex is found in the pwCepCfg table." INDEX { pwIndex, pwCepPerfIntervalNumber } ::= { pwCepPerfIntervalTable 1 } PwCepPerfIntervalEntry ::= SEQUENCE { pwCepPerfIntervalNumber Integer32, pwCepPerfIntervalValidData TruthValue, pwCepPerfIntervalReset INTEGER, pwCepPerfIntervalTimeElapsed HCPerfTimeElapsed, Danenberg et al Expires February 2006 34 Internet Draft PW CEP MIB July 2005 pwCepPerfIntervalDbaInPacketsHC HCPerfIntervalCount, pwCepPerfIntervalDbaOutPacketsHC HCPerfIntervalCount, pwCepPerfIntervalInNegPtrAdjust PerfIntervalCount, pwCepPerfIntervalInPosPtrAdjust PerfIntervalCount, pwCepPerfIntervalInPtrAdjustSecs PerfIntervalCount, pwCepPerfIntervalOutNegPtrAdjust PerfIntervalCount, pwCepPerfIntervalOutPosPtrAdjust PerfIntervalCount, pwCepPerfIntervalOutPtrAdjustSecs PerfIntervalCount, pwCepPerfIntervalAbsPtrAdjust Integer32, pwCepPerfIntervalMissingPkts PerfIntervalCount, pwCepPerfIntervalPktsOoseq PerfIntervalCount, pwCepPerfIntervalPktsOoRngDropped PerfIntervalCount, pwCepPerfIntervalJtrBfrUnderruns PerfIntervalCount, pwCepPerfIntervalPktsMalformed PerfIntervalCount, pwCepPerfIntervalSummaryErrors PerfIntervalCount, pwCepPerfIntervalESs PerfIntervalCount, pwCepPerfIntervalSESs PerfIntervalCount, pwCepPerfIntervalUASs PerfIntervalCount, pwCepPerfIntervalFC PerfIntervalCount } pwCepPerfIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96." ::= { pwCepPerfIntervalEntry 1 } pwCepPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwCepPerfIntervalEntry 2 } pwCepPerfIntervalReset OBJECT-TYPE SYNTAX INTEGER { reset (1), normal(2) Danenberg et al Expires February 2006 35 Internet Draft PW CEP MIB July 2005 } MAX-ACCESS read-create STATUS current DESCRIPTION "Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero." ::= { pwCepPerfIntervalEntry 3 } pwCepPerfIntervalTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided." ::= { pwCepPerfIntervalEntry 4 } pwCepPerfIntervalDbaInPacketsHC OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerfIntervalEntry 5 } pwCepPerfIntervalDbaOutPacketsHC OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerfIntervalEntry 6 } -- Pointer adjustment stats pwCepPerfIntervalInNegPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfIntervalEntry 7 } pwCepPerfIntervalInPosPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION Danenberg et al Expires February 2006 36 Internet Draft PW CEP MIB July 2005 "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfIntervalEntry 8 } pwCepPerfIntervalInPtrAdjustSecs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path." ::= { pwCepPerfIntervalEntry 9 } pwCepPerfIntervalOutNegPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfIntervalEntry 10 } pwCepPerfIntervalOutPosPtrAdjust OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfIntervalEntry 11 } pwCepPerfIntervalOutPtrAdjustSecs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path." ::= { pwCepPerfIntervalEntry 12 } pwCepPerfIntervalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerfIntervalEntry 13 } pwCepPerfIntervalMissingPkts OBJECT-TYPE SYNTAX PerfIntervalCount Danenberg et al Expires February 2006 37 Internet Draft PW CEP MIB July 2005 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwCepPerfIntervalEntry 14 } pwCepPerfIntervalPktsOoseq OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations mat not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerfIntervalEntry 15 } pwCepPerfIntervalPktsOoRngDropped OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer." ::= { pwCepPerfIntervalEntry 16 } pwCepPerfIntervalJtrBfrUnderruns OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerfIntervalEntry 17 } pwCepPerfIntervalPktsMalformed OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerfIntervalEntry 18 } pwCepPerfIntervalSummaryErrors OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwCepPerfIntervalEntry 19 } Danenberg et al Expires February 2006 38 Internet Draft PW CEP MIB July 2005 pwCepPerfIntervalESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerfIntervalEntry 20 } pwCepPerfIntervalSESs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds encountered." ::= { pwCepPerfIntervalEntry 21 } pwCepPerfIntervalUASs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Unavailable Seconds encountered." ::= { pwCepPerfIntervalEntry 22 } pwCepPerfIntervalFC OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period in which it begins." ::= { pwCepPerfIntervalEntry 23 } -- End CEP PW Performance Interval Table -- CEP PW Total Performance Table pwCepPerfTotalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per CEP PW performance information much like the pwCepPerfIntervalTable above. However, these counts represent complete historical information. Danenberg et al Expires February 2006 39 Internet Draft PW CEP MIB July 2005 NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEP PWs." ::= { pwCepObjects 7 } pwCepPerfTotalEntry OBJECT-TYPE SYNTAX PwCepPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created in this table by the agent for every entry in the pwCepTable." INDEX { pwIndex } ::= { pwCepPerfTotalTable 1 } PwCepPerfTotalEntry ::= SEQUENCE { pwCepPerfTotalDbaInPacketsHC Counter64, pwCepPerfTotalDbaOutPacketsHC Counter64, pwCepPerfTotalInNegPtrAdjust Counter32, pwCepPerfTotalInPosPtrAdjust Counter32, pwCepPerfTotalInPtrAdjustSecs Counter32, pwCepPerfTotalOutNegPtrAdjust Counter32, pwCepPerfTotalOutPosPtrAdjust Counter32, pwCepPerfTotalOutPtrAdjustSecs Counter32, pwCepPerfTotalAbsPtrAdjust Integer32, pwCepPerfTotalMissingPkts Counter32, pwCepPerfTotalPktsOoseq Counter32, pwCepPerfTotalPktsOoRngDropped Counter32, pwCepPerfTotalJtrBfrUnderruns Counter32, pwCepPerfTotalPktsMalformed Counter32, pwCepPerfTotalSummaryErrors Counter32, pwCepPerfTotalESs Counter32, pwCepPerfTotalSESs Counter32, pwCepPerfTotalUASs Counter32, pwCepPerfTotalFC Counter32, pwCepPerfTotalDiscontinuityTime TimeStamp } pwCepPerfTotalDbaInPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of DBA packets received." ::= { pwCepPerfTotalEntry 1 } pwCepPerfTotalDbaOutPacketsHC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only Danenberg et al Expires February 2006 40 Internet Draft PW CEP MIB July 2005 STATUS current DESCRIPTION "Number of DBA packets sent." ::= { pwCepPerfTotalEntry 2 } -- Pointer adjustment stats pwCepPerfTotalInNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfTotalEntry 3 } pwCepPerfTotalInPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments sent on the SONET path based on CEP pointer adjustments received." ::= { pwCepPerfTotalEntry 4 } pwCepPerfTotalInPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was sent on the SONET path." ::= { pwCepPerfTotalEntry 5 } pwCepPerfTotalOutNegPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfTotalEntry 6 } pwCepPerfTotalOutPosPtrAdjust OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets." ::= { pwCepPerfTotalEntry 7 } pwCepPerfTotalOutPtrAdjustSecs OBJECT-TYPE SYNTAX Counter32 Danenberg et al Expires February 2006 41 Internet Draft PW CEP MIB July 2005 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds in which a positive or negative pointer adjustment was seen on the SONET path." ::= { pwCepPerfTotalEntry 8 } pwCepPerfTotalAbsPtrAdjust OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust) " ::= { pwCepPerfTotalEntry 9 } pwCepPerfTotalMissingPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of missing packets (as detected via CEP header sequence number gaps)." ::= { pwCepPerfTotalEntry 10 } pwCepPerfTotalPktsOoseq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feature (see pwCepCfgPktReorder)." ::= { pwCepPerfTotalEntry 11 } pwCepPerfTotalPktsOoRngDropped OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected out of range (via CEP header sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer." ::= { pwCepPerfTotalEntry 12 } pwCepPerfTotalJtrBfrUnderruns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Danenberg et al Expires February 2006 42 Internet Draft PW CEP MIB July 2005 "Number of times a packet needed to be played out and the jitter buffer was empty." ::= { pwCepPerfTotalEntry 13 } pwCepPerfTotalPktsMalformed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets detected with unexpected size, or bad headers stack." ::= { pwCepPerfTotalEntry 14 } pwCepPerfTotalSummaryErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A summary of all the packet error types above (from missing packets to bad length packets)." ::= { pwCepPerfTotalEntry 15 } pwCepPerfTotalESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Errored Seconds encountered." ::= { pwCepPerfTotalEntry 16 } pwCepPerfTotalSESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of Severely Errored Seconds. See pwCepCfgMissingPktsToSes." ::= { pwCepPerfTotalEntry 17 } pwCepPerfTotalUASs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The counter associated with the number of UnAvailable Seconds. See pwCepCfgSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added to this object, then as each additional UAS occurs, this object increments by one. NOTE: Similar to RFC 3592, If the agent chooses to update the various performance statistics in real time then it must Danenberg et al Expires February 2006 43 Internet Draft PW CEP MIB July 2005 be prepared to retroactively reduce the ES, SES, counts (by the value of pwCepCfgSesToUas) and increase the UAS count (by that same value) when it determines that UAS state has been entered." ::= { pwCepPerfTotalEntry 18 } pwCepPerfTotalFC OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared." ::= { pwCepPerfTotalEntry 19 } pwCepPerfTotalDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value." ::= { pwCepPerfTotalEntry 20 } -- End of PW CEP Total Performance table -- Conformance Configuration table pwCepConformanceCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PwCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the means for the agent to declare whether certain CEP PW statistics objects are supported (conformed to) or not." ::= { pwCepObjects 9 } pwCepConformanceCfgEntry OBJECT-TYPE SYNTAX PwCepConformanceCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The agent MUST create a single entry in this table." INDEX { pwCepConformanceCfgIndex } Danenberg et al Expires February 2006 44 Internet Draft PW CEP MIB July 2005 ::= { pwCepConformanceCfgTable 1 } PwCepConformanceCfgEntry ::= SEQUENCE { pwCepConformanceCfgIndex INTEGER, pwCepPerfDbaInPacketsHCTruth TruthValue, pwCepPerfDbaInPacketsHCDesc SnmpAdminString, pwCepPerfDbaOutPacketsHCTruth TruthValue, pwCepPerfDbaOutPacketsHCDesc SnmpAdminString, pwCepPerfPktsOoseqTruth TruthValue, pwCepPerfPktsOoseqDesc SnmpAdminString, pwCepPerfPktsOoRngDroppedTruth TruthValue, pwCepPerfPktsOoRngDroppedDesc SnmpAdminString, pwCepPerfSummaryErrorsTruth TruthValue, pwCepPerfSummaryErrorsDesc SnmpAdminString } pwCepConformanceCfgIndex OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Any arbitrary number." ::= { pwCepConformanceCfgEntry 1 } pwCepPerfDbaInPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...DbaInPacketsHC in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 2 } pwCepPerfDbaInPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...DbaInPacketsHC support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 3 } pwCepPerfDbaOutPacketsHCTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...DbaOutPacketsHC Danenberg et al Expires February 2006 45 Internet Draft PW CEP MIB July 2005 in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 4 } pwCepPerfDbaOutPacketsHCDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...DbaOutPacketsHC support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 5 } pwCepPerfPktsOoseqTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...PktsOoseq in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 6 } pwCepPerfPktsOoseqDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...PktsOoseq support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 7 } pwCepPerfPktsOoRngDroppedTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Tells whether the pwCepPerf...PktsOoRngDropped in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 8 } pwCepPerfPktsOoRngDroppedDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...PktsOoRngDropped support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 9 } pwCepPerfSummaryErrorsTruth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION Danenberg et al Expires February 2006 46 Internet Draft PW CEP MIB July 2005 "Tells whether the pwCepPerf...SummaryError in the pwCepPerf...Table is supported." ::= { pwCepConformanceCfgEntry 10 } pwCepPerfSummaryErrorsDesc OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Explanation for pwCepPerf...SummaryError support in the pwCepPerf...Table." ::= { pwCepConformanceCfgEntry 11 } -- End of CEP PW Conformance report table -- Conformance Information pwCepGroups OBJECT IDENTIFIER ::= { pwCepConformance 1 } pwCepCompliances OBJECT IDENTIFIER ::= { pwCepConformance 2 } -- Compliance statement for full compliant implementations pwCepModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agent that support full CEP PW configuration through this MIB module." MODULE -- this module MANDATORY-GROUPS { pwCepGroup, pwCepCfgGroup, pwCepPerfCurrentGroup, pwCepPerfIntervalGroup, pwCepPerfTotalGroup, pwCepConformanceCfgGroup } GROUP pwPwCepFractionalGroup DESCRIPTION "This group is only mandatory for implementations that support fractional SPE. " GROUP pwPwCepFractionalSts1Vc3Group DESCRIPTION "This group is only mandatory for implementations that support the fractional STS-1/VC-3. " GROUP pwPwCepFractionalVc4Group DESCRIPTION "This group is only mandatory for implementations that support the Fractional VC-4. " Danenberg et al Expires February 2006 47 Internet Draft PW CEP MIB July 2005 GROUP pwPwCepSignalingGroup DESCRIPTION "This group is only mandatory for implementations that support the CEP PW signaling. " OBJECT pwCepType SYNTAX INTEGER { spe(1) } MIN-ACCESS read-only DESCRIPTION "The support of the value vt(2) or fracSpe(3) is optional. If either of these options are supported, read-write access is not required." OBJECT pwCepSonetPayloadLength MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only the default values (which are based on the pwCepType)." OBJECT pwCepCfgMinPktLength MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgEnableDBA MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgRtpHdrSuppress MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that do not support RTP header for CEP connections." OBJECT pwCepCfgConsecPktsInsync MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgConsecMissingOutSync MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgPktErrorPlayOutValue MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgMissingPktsToSes MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." Danenberg et al Expires February 2006 48 Internet Draft PW CEP MIB July 2005 OBJECT pwCepCfgSesToUas MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgSecsToExitUas MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepCfgRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required." OBJECT pwCepFracMode MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracAsync SYNTAX PwCepFracAsyncMap { other(0) } MIN-ACCESS read-only DESCRIPTION "Support for ds3(1) or e3(2) and read-write access is not required if the implementation do not support these options." OBJECT pwCepFracVtgMap MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracEbm MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Mode MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations Danenberg et al Expires February 2006 49 Internet Draft PW CEP MIB July 2005 that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tu3Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Tug2Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations that support only a single pre-defined value." OBJECT pwCepFracSdhVc4Ebm1 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Ebm2 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracSdhVc4Ebm3 MIN-ACCESS read-only DESCRIPTION "Write access is not required for implementations where the EBM is derived from configuration in other MIB modules." OBJECT pwCepFracRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required." ::= { pwCepCompliances 1 } -- Compliance requirement for read only compliant implementations. pwModuleReadOnlyCompliance MODULE-COMPLIANCE Danenberg et al Expires February 2006 50 Internet Draft PW CEP MIB July 2005 STATUS current DESCRIPTION "The compliance statement for agents that provide read only support for PW CEP MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwCepGroup, pwCepCfgGroup, pwCepPerfCurrentGroup, pwCepPerfIntervalGroup, pwCepPerfTotalGroup, pwCepConformanceCfgGroup } GROUP pwPwCepFractionalGroup DESCRIPTION "This group is only mandatory for implementations that support fractional SPE. " GROUP pwPwCepFractionalSts1Vc3Group DESCRIPTION "This group is only mandatory for implementations that support the fractional STS-1/VC-3. " GROUP pwPwCepFractionalVc4Group DESCRIPTION "This group is only mandatory for implementations that support the Fractional VC-4. " GROUP pwPwCepSignalingGroup DESCRIPTION "This group is only mandatory for implementations that support the CEP PW signaling. " OBJECT pwCepType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepSonetIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepSonetPayloadLength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgMinPktLength MIN-ACCESS read-only Danenberg et al Expires February 2006 51 Internet Draft PW CEP MIB July 2005 DESCRIPTION "Write access is not required." OBJECT pwCepCfgEnableDBA MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgRtpHdrSuppress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgJtrBfrDepth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgConsecPktsInsync MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgConsecMissingOutSync MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgPktErrorPlayOutValue MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgMissingPktsToSes MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgSesToUas MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgSecsToExitUas MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepCfgRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required.." OBJECT pwCepCfgStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required.." OBJECT pwCepFracMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracAsync MIN-ACCESS read-only DESCRIPTION "Write access is not required." Danenberg et al Expires February 2006 52 Internet Draft PW CEP MIB July 2005 OBJECT pwCepFracVtgMap MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracEbm MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Mode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tu3Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tu3Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tu3Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Tug2Map3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracSdhVc4Ebm3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCepFracStorageType MIN-ACCESS read-only Danenberg et al Expires February 2006 53 Internet Draft PW CEP MIB July 2005 DESCRIPTION "Write access is not required." ::= { pwCepCompliances 2 } -- Units of conformance. pwCepGroup OBJECT-GROUP OBJECTS { pwCepType, pwCepSonetIfIndex, pwCepSonetConfigErrorOrStatus, pwCepCfgIndex, pwCepTimeElapsed, pwCepValidIntervals, pwCepCurrentIndications, pwCepLatchedIndications, pwCepLastEsTimeStamp } STATUS current DESCRIPTION "Collection of objects for basic CEP PW config and status." ::= { pwCepGroups 1 } pwPwCepSignalingGroup OBJECT-GROUP OBJECTS { pwCepPeerCepOption } STATUS current DESCRIPTION "Collection of objects required if the network element support CEP connections signaling." ::= { pwCepGroups 2 } pwCepCfgGroup OBJECT-GROUP OBJECTS { pwCepCfgIndexNext, pwCepConfigError, pwCepSonetPayloadLength, pwCepCfgMinPktLength, pwCepCfgPktReorder, pwCepCfgEnableDBA, pwCepCfgRtpHdrSuppress, pwCepCfgJtrBfrDepth, pwCepCfgConsecPktsInsync, pwCepCfgConsecMissingOutSync, pwCepCfgPktErrorPlayOutValue, Danenberg et al Expires February 2006 54 Internet Draft PW CEP MIB July 2005 pwCepCfgMissingPktsToSes, pwCepCfgSesToUas, pwCepCfgSecsToExitUas, pwCepCfgRowStatus, pwCepCfgStorageType } STATUS current DESCRIPTION "Collection of detailed objects needed to configure CEP PWs." ::= { pwCepGroups 3 } pwCepPerfCurrentGroup OBJECT-GROUP OBJECTS { pwCepPerfCurrentDbaInPacketsHC, pwCepPerfCurrentDbaOutPacketsHC, pwCepPerfCurrentInNegPtrAdjust, pwCepPerfCurrentInPosPtrAdjust, pwCepPerfCurrentInPtrAdjustSecs, pwCepPerfCurrentOutNegPtrAdjust, pwCepPerfCurrentOutPosPtrAdjust, pwCepPerfCurrentOutPtrAdjustSecs, pwCepPerfCurrentAbsPtrAdjust, pwCepPerfCurrentMissingPkts, pwCepPerfCurrentPktsOoseq, pwCepPerfCurrentPktsOoRngDropped, pwCepPerfCurrentJtrBfrUnderruns, pwCepPerfCurrentPktsMalformed, pwCepPerfCurrentSummaryErrors, pwCepPerfCurrentESs, pwCepPerfCurrentSESs, pwCepPerfCurrentUASs, pwCepPerfCurrentFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 4 } pwCepPerfIntervalGroup OBJECT-GROUP OBJECTS { pwCepPerfIntervalValidData, pwCepPerfIntervalReset, pwCepPerfIntervalTimeElapsed, pwCepPerfIntervalDbaInPacketsHC, pwCepPerfIntervalDbaOutPacketsHC, Danenberg et al Expires February 2006 55 Internet Draft PW CEP MIB July 2005 pwCepPerfIntervalInNegPtrAdjust, pwCepPerfIntervalInPosPtrAdjust, pwCepPerfIntervalInPtrAdjustSecs, pwCepPerfIntervalOutNegPtrAdjust, pwCepPerfIntervalOutPosPtrAdjust, pwCepPerfIntervalOutPtrAdjustSecs, pwCepPerfIntervalAbsPtrAdjust, pwCepPerfIntervalMissingPkts, pwCepPerfIntervalPktsOoseq, pwCepPerfIntervalPktsOoRngDropped, pwCepPerfIntervalJtrBfrUnderruns, pwCepPerfIntervalPktsMalformed, pwCepPerfIntervalSummaryErrors, pwCepPerfIntervalESs, pwCepPerfIntervalSESs, pwCepPerfIntervalUASs, pwCepPerfIntervalFC } STATUS current DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 5 } pwCepPerfTotalGroup OBJECT-GROUP OBJECTS { pwCepPerfTotalDbaInPacketsHC, pwCepPerfTotalDbaOutPacketsHC, pwCepPerfTotalInNegPtrAdjust, pwCepPerfTotalInPosPtrAdjust, pwCepPerfTotalInPtrAdjustSecs, pwCepPerfTotalOutNegPtrAdjust, pwCepPerfTotalOutPosPtrAdjust, pwCepPerfTotalOutPtrAdjustSecs, pwCepPerfTotalAbsPtrAdjust, pwCepPerfTotalMissingPkts, pwCepPerfTotalPktsOoseq, pwCepPerfTotalPktsOoRngDropped, pwCepPerfTotalJtrBfrUnderruns, pwCepPerfTotalPktsMalformed, pwCepPerfTotalSummaryErrors, pwCepPerfTotalESs, pwCepPerfTotalSESs, pwCepPerfTotalUASs, pwCepPerfTotalFC, pwCepPerfTotalDiscontinuityTime } STATUS current Danenberg et al Expires February 2006 56 Internet Draft PW CEP MIB July 2005 DESCRIPTION "Collection of statistics objects for CEP PWs." ::= { pwCepGroups 6 } pwPwCepFractionalGroup OBJECT-GROUP OBJECTS { pwCepFracRowStatus, pwCepFracStorageType } STATUS current DESCRIPTION "Collection of fractional SPE objects. These objects are optional and should be supported only if fractional SPE is supported within the network element. " ::= { pwCepGroups 7 } pwPwCepFractionalSts1Vc3Group OBJECT-GROUP OBJECTS { pwCepFracMode, pwCepFracConfigError, pwCepFracAsync, pwCepFracVtgMap, pwCepFracEbm, pwCepFracPeerEbm } STATUS current DESCRIPTION "Collection of fractional STS-1/VC3 objects. These objects are optional and should be supported only if fractional STS-1/VC3 is supported within the network element. " ::= { pwCepGroups 8 } pwPwCepFractionalVc4Group OBJECT-GROUP OBJECTS { pwCepFracSdhVc4Mode, pwCepFracSdhVc4Tu3Map1, pwCepFracSdhVc4Tu3Map2, pwCepFracSdhVc4Tu3Map3, pwCepFracSdhVc4Tug2Map1, pwCepFracSdhVc4Tug2Map2, pwCepFracSdhVc4Tug2Map3, pwCepFracSdhVc4Ebm1, pwCepFracSdhVc4Ebm2, pwCepFracSdhVc4Ebm3, pwCepFracSdhVc4PeerEbm1, pwCepFracSdhVc4PeerEbm2, pwCepFracSdhVc4PeerEbm3 } STATUS current DESCRIPTION "Collection of fractional VC4 objects. These objects Danenberg et al Expires February 2006 57 Internet Draft PW CEP MIB July 2005 are optional and should be supported only if fractional VC4 is supported within the network element. " ::= { pwCepGroups 9 } pwCepConformanceCfgGroup OBJECT-GROUP OBJECTS { pwCepPerfDbaInPacketsHCTruth, pwCepPerfDbaInPacketsHCDesc, pwCepPerfDbaOutPacketsHCTruth, pwCepPerfDbaOutPacketsHCDesc, pwCepPerfPktsOoseqTruth, pwCepPerfPktsOoseqDesc, pwCepPerfPktsOoRngDroppedTruth, pwCepPerfPktsOoRngDroppedDesc, pwCepPerfSummaryErrorsTruth, pwCepPerfSummaryErrorsDesc } STATUS current DESCRIPTION "Collection of objects declaring conformance to other objects." ::= { pwCepGroups 10 } END -- -- Copyright (C) The Internet Society (2005). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- -- 13 IANA considerations -- -- PWE3 related standards track PW modules should be rooted under the -- pwMIB subtree. The IANA is requested to manage that namespace. New -- assignments can only be made via a Standards Action as specified in -- [RFC2434]. -- -- IANA is requested to make a MIB OID assignment under the pwMIB -- branch as specified in section 12.1. -- -- 12.1 IANA Considerations for PW-CEP-STD-MIB -- -- This document also requests IANA to assign { pwMIB 5 } to the PW- -- CEP-STD-MIB module specified in this document. -- -- 14 Acknowledgement -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society. -- -- -- -- -- -- -- -- -- -- -- -- -- -- Danenberg et al Expires February 2006 62