-- extracted from draft-ietf-pwe3-pw-mpls-mib-09.txt -- at Wed Jun 28 06:06:35 2006 PW-MPLS-STD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, transmission FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] StorageType FROM SNMPv2-TC -- [RFC2579] InterfaceIndexOrZero FROM IF-MIB -- [RFC2863] MplsTunnelIndex, MplsTunnelInstanceIndex, MplsLdpIdentifier, MplsLsrIdentifier FROM MPLS-TC-STD-MIB -- [RFC3810] MplsIndexType Pseudo Wire (PW) Over MPLS June 2006 Management Information Base FROM MPLS-LSR-STD-MIB -- [RFC3813] PwIndexType FROM PW-TC-STD-MIB -- [RFCxxxx] -- RFC Editor: Please replace XXXX with RFC number & remove this -- note. pwIndex -- [RFCxxxx] -- RFC Editor: Please replace XXXX with RFC number & remove this -- note. FROM PW-STD-MIB ; pwMplsStdMIB MODULE-IDENTITY LAST-UPDATED "200606141200Z" -- 14 June 2006 12:00:00 GMT ORGANIZATION "Pseudo Wire Edge to Edge Emulation (PWE3) Working Group." CONTACT-INFO " David Zelig, Editor E-mail: davidz@corrigent.com Thomas D. Nadeau, Editor Email: tnadeau@cisco.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module complements the PW-STD-MIB module for PW operation over MPLS. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices. -- RFC Ed.: replace yyyy with actual RFC number & remove -- this note " -- Revision history. REVISION "200606141200Z" -- 14 June 2006 12:00:00 GMT DESCRIPTION " First published as RFCWXYZ. " -- RFC Editor: Please replace WXYZ with correct # and remove this -- note ::= { transmission XXX } -- RFC Editor: To be assigned by IANA. Please replace XXX -- with the assigned value and remove this note. -- Top-level components of this MIB. Pseudo Wire (PW) Over MPLS June 2006 Management Information Base -- Notifications pwMplsNotifications OBJECT IDENTIFIER ::= { pwMplsStdMIB 0 } -- Tables, Scalars pwMplsObjects OBJECT IDENTIFIER ::= { pwMplsStdMIB 1 } -- Conformance pwMplsConformance OBJECT IDENTIFIER ::= { pwMplsStdMIB 2 } -- PW MPLS table pwMplsTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table controls MPLS specific parameters when the PW is going to be carried over MPLS PSN." ::= { pwMplsObjects 1 } pwMplsEntry OBJECT-TYPE SYNTAX PwMplsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents parameters specific to MPLS PSN for a pseudo wire (PW). The row is created automatically by the local agent if the pwPsnType is MPLS. It is indexed by pwIndex, which uniquely identifying a singular PW. " INDEX { pwIndex } ::= { pwMplsTable 1 } PwMplsEntry ::= SEQUENCE { pwMplsMplsType BITS, pwMplsExpBitsMode INTEGER, pwMplsExpBits Unsigned32, pwMplsTtl Unsigned32, pwMplsLocalLdpID MplsLdpIdentifier, pwMplsLocalLdpEntityIndex Unsigned32, pwMplsPeerLdpID MplsLdpIdentifier, pwMplsStorageType StorageType } pwMplsMplsType OBJECT-TYPE SYNTAX BITS { Pseudo Wire (PW) Over MPLS June 2006 Management Information Base mplsTe (0), mplsNonTe (1), pwOnly (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the outer tunnel types, if exists. mplsTe(0) is used if the outer tunnel was set-up by MPLS-TE, and mplsNonTe(1) is used the outer tunnel was set up by LDP or manually. Combination of mplsTe(0) and mplsNonTe(1) may exist together. pwOnly(2) is used if there is no outer tunnel label, i.e. in static provisioning without MPLS tunnel. pwOnly(2) cannot be combined with mplsNonTe(1) or mplsTe(0)." DEFVAL { { mplsNonTe } } ::= { pwMplsEntry 1 } pwMplsExpBitsMode OBJECT-TYPE SYNTAX INTEGER { outerTunnel (1), specifiedValue (2), serviceDependant (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the way the PW shim label EXP bits are to be determined. The value of outerTunnel(1) is used where there is an outer tunnel - pwMplsMplsType is mplsTe(0) or mplsNonTe(1). Note that in this case there is no need to mark the PW label with the EXP bits since the PW label is not visible to the intermediate nodes. If there is no outer tunnel, specifiedValue(2) indicates that the value is specified by pwMplsExpBits, and serviceDependant(3) indicates that the EXP bits are set based on a rule which is implementation specific." DEFVAL { outerTunnel } ::= { pwMplsEntry 2 } pwMplsExpBits OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the MPLS EXP bits to be used on the PW shim label if pwMplsExpBitsMode is specifiedValue(2), zero otherwise." DEFVAL { 0 } Pseudo Wire (PW) Over MPLS June 2006 Management Information Base ::= { pwMplsEntry 3 } pwMplsTtl OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set by the operator to indicate the PW TTL value to be used on the PW shim label." DEFVAL { 2 } ::= { pwMplsEntry 4 } pwMplsLocalLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The local LDP identifier of the LDP entity creating this PW in the local node. As the PW labels are always set from the per platform label space, the last two octets in the LDP ID MUST be always both zeros." REFERENCE "'LDP specifications', RFC 3036 section 2.2.2." ::= { pwMplsEntry 5 } pwMplsLocalLdpEntityIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The local node LDP Entity Index of the LDP entity creating this PW." ::= { pwMplsEntry 6 } pwMplsPeerLdpID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The peer LDP identifier as identified from the LDP session. Should return the value of zero if not applicable or not known yet." ::= { pwMplsEntry 7 } pwMplsStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the storage type for this row." ::= { pwMplsEntry 8 } Pseudo Wire (PW) Over MPLS June 2006 Management Information Base -- End of PW MPLS table -- Pseudo Wire MPLS Outbound Tunnel table pwMplsOutboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table reports and configure the current outbound MPLS tunnels (i.e. toward the PSN) or the physical interface in case of PW label only that carry the PW traffic. It also reports the current outer tunnel and LSP which forward the PW traffic." ::= { pwMplsObjects 2 } pwMplsOutboundEntry OBJECT-TYPE SYNTAX PwMplsOutboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table configures the outer tunnel used for carrying the PW traffic toward the PSN. In the case of PW label only, it configures the interface that will carry the PW traffic. An entry in this table augments the pwMplsEntry, and is created automatically when the corresponding row has been created by the agent in the pwMplsEntry. This table points to the appropriate MPLS MIB module. In the MPLS-TE case, the 3 variables relevant to the indexing of a TE tunnel head-end are used as in MPLS-TE-STD-MIB are to be configured, and the tunnel instance indicates the LSP that is currently in use for forwarding the traffic. In case of signaled Non-TE MPLS (an outer tunnel label assigned by LDP) the table points to the XC entry in the LSR-STD-MIB. If the Non-TE MPLS tunnel is manually configured, the operator configures the XC pointer to this tunnel. In case of PW label only (no outer tunnel) the ifIndex of the port to carry the PW is configured here. It is possible to associate a PW to one TE tunnel head-end and a non-TE tunnel together. An indication in this table will report the currently active one, In addition, in the TE case the table reports the active tunnel instance Pseudo Wire (PW) Over MPLS June 2006 Management Information Base (i.e. the specific LSP in use). " AUGMENTS { pwMplsEntry } ::= { pwMplsOutboundTable 1 } PwMplsOutboundEntry ::= SEQUENCE { pwMplsOutboundLsrXcIndex MplsIndexType, pwMplsOutboundTunnelIndex MplsTunnelIndex, pwMplsOutboundTunnelInstance MplsTunnelInstanceIndex, pwMplsOutboundTunnelLclLSR MplsLsrIdentifier, pwMplsOutboundTunnelPeerLSR MplsLsrIdentifier, pwMplsOutboundIfIndex InterfaceIndexOrZero, pwMplsOutboundTunnelTypeInUse INTEGER } pwMplsOutboundLsrXcIndex OBJECT-TYPE SYNTAX MplsIndexType MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwMplsMplsType mplsNonTe(1) bit is set, and MUST return a value of zero otherwise. If the outer tunnel is signaled, the object is read-only and indicates the XC index in the MPLS-LSR-STD-MIB of the outer tunnel toward the peer. Otherwise (tunnel is set-up manually) the operator defines the XC index of the manually created outer tunnel through this object. " ::= { pwMplsOutboundEntry 1 } pwMplsOutboundTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is Part of set of indexes for outbound tunnel. The operator set this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwMplsOutboundEntry 2 } pwMplsOutboundTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS read-only STATUS current Pseudo Wire (PW) Over MPLS June 2006 Management Information Base DESCRIPTION "This object is applicable if pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It indicates the actual tunnel instance that is currently active and carrying the PW traffic - it should return the value of zero until if the information from the MPLS-TE application is not yet known. " ::= { pwMplsOutboundEntry 3 } pwMplsOutboundTunnelLclLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of all zeros otherwise. It is part of set of indexes for outbound tunnel. The operator set this object to represent the desired tunnel head-end toward the peer for carrying the PW traffic. " ::= { pwMplsOutboundEntry 4 } pwMplsOutboundTunnelPeerLSR OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwMplsMplsType mplsTe(0) bit is set, and MUST return a value of zero otherwise. It is part of set of indexes for outbound tunnel. It is typically equal to pwPeerAddr. " ::= { pwMplsOutboundEntry 5 } pwMplsOutboundIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This object is applicable if pwMplsMplsType pwOnly(0) bit is set, and MUST return a value of zero otherwise. The operator configure the ifIndex of the outbound port in this case. " ::= { pwMplsOutboundEntry 6 } pwMplsOutboundTunnelTypeInUse OBJECT-TYPE SYNTAX INTEGER { notYetKnown (1), Pseudo Wire (PW) Over MPLS June 2006 Management Information Base mplsTe (2), mplsNonTe (3), pwOnly (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current tunnel that is carrying the PW traffic. The value of notYetKnown(1) should be used if the agent is currently unable to determine which tunnel or interface is carrying the PW, for example because both tunnels are in operational status down. " ::= { pwMplsOutboundEntry 7 } -- End of PW MPLS Outbound Tunnel table -- PW MPLS inbound table pwMplsInboundTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the PW LDP XC entry in the MPLS-LSR-STD-MIB for signaled PWs. " ::= { pwMplsObjects 3 } pwMplsInboundEntry OBJECT-TYPE SYNTAX PwMplsInboundEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table is created by the agent for each signaled PW, and shows the XC index related to the PW signaling in the inbound direction in the MPLS-LSR-STD-MIB that controls and display the information for all the LDP signaling processes in the local node. " INDEX { pwIndex } ::= { pwMplsInboundTable 1 } PwMplsInboundEntry ::= SEQUENCE { pwMplsInboundXcIndex MplsIndexType } pwMplsInboundXcIndex OBJECT-TYPE Pseudo Wire (PW) Over MPLS June 2006 Management Information Base SYNTAX MplsIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The XC index representing this PW in the inbound direction. Should return the value of zero if the information is not yet known." ::= { pwMplsInboundEntry 1 } -- End of PW MPLS inbound table -- PW to Non-TE mapping Table. pwMplsNonTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates outbound Tunnel to a PW in non-TE applications, maps the PW to it's (inbound) XC entry, and indicates the PW to physical interface mapping for a PW label to physical interface a PW label is in use without outer tunnel. " ::= { pwMplsObjects 4 } pwMplsNonTeMappingEntry OBJECT-TYPE SYNTAX PwMplsNonTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table displays the association between the PW and - it's non-TE MPLS outbound outer Tunnel or, - it's XC entry in the MPLS-LSR-STD-MIB, - it's physical interface if there is no outer tunnel (PW label only) and manual configuration. Rows are created in this table by the by the agent depending on the setting of pwMplsMplsType: - If pwMplsMplsType mplsNonTe(1) bit is set, the agent creates a row for the outbound direction (pwMplsNonTeMappingDirection set to psnBound(1)). The pwMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PSN bound outer tunnel. pwMplsNonTeMappingIfIndex MUST be zero for this row. - If pwMplsMplsType pwOnly(2) bit is set, the agent creates a row for the outbound direction (pwMplsNonTeMappingDirection set to psnBound(1)). Pseudo Wire (PW) Over MPLS June 2006 Management Information Base The pwMplsNonTeMappingIfIndex holds the ifIndex of the physical port this PW will use in the outbound direction. pwMplsNonTeMappingXcIndex MUST be zero for this row. - If the PW has been set-up by signaling protocol (i.e. pwOwner equal pwIdFecSignaling(2) or genFecSignaling(3)), the agent creates a row for the inbound direction (pwMplsNonTeMappingDirection set to fromPsn(2)). The pwMplsNonTeMappingXcIndex holds the XC index in the MPLS-LSR-STD-MIB of the PW LDP generated XC entry. pwMplsNonTeMappingIfIndex MUST be zero for this row. An application can use this table to quickly retrieve the PW carried over specific non-TE MPLS outer tunnel or physical interface. " INDEX { pwMplsNonTeMappingDirection, pwMplsNonTeMappingXcIndex, pwMplsNonTeMappingIfIndex, pwMplsNonTeMappingPwIndex } ::= { pwMplsNonTeMappingTable 1 } PwMplsNonTeMappingEntry ::= SEQUENCE { pwMplsNonTeMappingDirection INTEGER, pwMplsNonTeMappingXcIndex MplsIndexType, pwMplsNonTeMappingIfIndex InterfaceIndexOrZero, pwMplsNonTeMappingPwIndex PwIndexType } pwMplsNonTeMappingDirection OBJECT-TYPE SYNTAX INTEGER { psnBound (1), fromPsn (2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the conceptual XC row identifying Tunnel to PW mappings, indicating the direction of packet flow the entry is related too. psnBound(1) indicates that the entry is related to packets toward the PSN. fromPsn(2) indicates that the entry is related to packets coming from the PSN. " ::= { pwMplsNonTeMappingEntry 1 } pwMplsNonTeMappingXcIndex OBJECT-TYPE Pseudo Wire (PW) Over MPLS June 2006 Management Information Base SYNTAX MplsIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwMplsNonTeMappingEntry 2 } pwMplsNonTeMappingIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "See the description clause of pwMplsNonTeMappingEntry for the usage guidelines of this object." ::= { pwMplsNonTeMappingEntry 3 } pwMplsNonTeMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represent the PW in the pwTable." ::= { pwMplsNonTeMappingEntry 4 } -- End of PW to Non-TE mapping Table. -- PW to TE MPLS tunnels mapping Table. pwMplsTeMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table enable the retrieval of a PW association to the outbound MPLS tunnel for MPLS-TE applications." ::= { pwMplsObjects 5 } pwMplsTeMappingEntry OBJECT-TYPE SYNTAX PwMplsTeMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents the association between a PW and it's MPLS-TE outer (head-end) Tunnel. An application can use this table to quickly retrieve the list of the PWs that are configured on a specific MPLS TE outer tunnel. Pseudo Wire (PW) Over MPLS June 2006 Management Information Base The pwMplsTeMappingTunnelInstance reports the actual LSP out of the tunnel head-end that is currently forwarding the traffic. The table in indexed by the head-end indexes of a TE tunnel and the PW index. " INDEX { pwMplsTeMappingTunnelIndex, pwMplsTeMappingTunnelInstance, pwMplsTeMappingTunnelPeerLsrID, pwMplsTeMappingTunnelLocalLsrID, pwMplsTeMappingPwIndex } ::= { pwMplsTeMappingTable 1 } PwMplsTeMappingEntry ::= SEQUENCE { pwMplsTeMappingTunnelIndex MplsTunnelIndex, pwMplsTeMappingTunnelInstance MplsTunnelInstanceIndex, pwMplsTeMappingTunnelPeerLsrID MplsLsrIdentifier, pwMplsTeMappingTunnelLocalLsrID MplsLsrIdentifier, pwMplsTeMappingPwIndex PwIndexType } pwMplsTeMappingTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index for the conceptual row identifying the MPLS-TE tunnel that is carrying the PW traffic." ::= { pwMplsTeMappingEntry 1 } pwMplsTeMappingTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identify the MPLS-TE LSP that is carrying the PW traffic. Should return the value of zero if the information of the specific LSP is not yet known. Note that based on the recommendation in the MPLS-TC-STD-MIB, instance index 0 should refer to the configured tunnel interface." ::= { pwMplsTeMappingEntry 2 } pwMplsTeMappingTunnelPeerLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION Pseudo Wire (PW) Over MPLS June 2006 Management Information Base "Identifies the Peer LSR when the outer tunnel is MPLS-TE based." ::= { pwMplsTeMappingEntry 3 } pwMplsTeMappingTunnelLocalLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the local LSR." ::= { pwMplsTeMappingEntry 4 } pwMplsTeMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represent the PW in the pwTable." ::= { pwMplsTeMappingEntry 5 } -- End of PW to TE MPLS tunnels mapping Table. -- conformance information pwMplsGroups OBJECT IDENTIFIER ::= { pwMplsConformance 1 } pwMplsCompliances OBJECT IDENTIFIER ::= { pwMplsConformance 2 } -- Compliance requirement for fully compliant implementations. pwMplsModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide full support for PW-MPLS MIB Module. Such devices can then be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwMplsGroup, pwMplsOutboundMainGroup, pwMplsInboundGroup, pwMplsMappingGroup } GROUP pwMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS TE tunnels to carry PW traffic. " OBJECT pwMplsMplsType DESCRIPTION "Support of pwOnly(2) is not required. At least one Pseudo Wire (PW) Over MPLS June 2006 Management Information Base of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwMplsExpBitsMode DESCRIPTION "Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity identifier for PW signaling. " OBJECT pwMplsLocalLdpEntityIndex MIN-ACCESS read-only DESCRIPTION "A read-write access is required if the implementation supports more than one LDP entity index for PW signaling. " OBJECT pwMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero MUST be supported if the implementation support non TE signaling of the outer tunnel. A read-write access MUST be supported if the implementation supports manually setting of the PW labels and carrying them over non-TE tunnels. " OBJECT pwMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "A value other than zero and read-write operations MUST be supported if the implementation supports manully configured PW without MPLS outer tunnel. " ::= { pwMplsCompliances 1 } -- Compliance requirement for Read Only compliant implementations. pwMplsModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read only support for PW-MPLS MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." Pseudo Wire (PW) Over MPLS June 2006 Management Information Base MODULE -- this module MANDATORY-GROUPS { pwMplsGroup, pwMplsOutboundMainGroup, pwMplsInboundGroup, pwMplsMappingGroup } GROUP pwMplsOutboundTeGroup DESCRIPTION "This group MUST be supported if the implementation allows MPLS TE tunnels to carry PW traffic. " OBJECT pwMplsMplsType MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support of pwOnly(2) is not required. At least one of mplsTe(0) or mplsNonTe(1) MUST be supported if signaling of PW is supported. " OBJECT pwMplsExpBitsMode MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support of specifiedValue(2) and serviceDependant(3) is optional. " OBJECT pwMplsExpBits MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsLocalLdpID MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsLocalLdpEntityIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. " Pseudo Wire (PW) Over MPLS June 2006 Management Information Base OBJECT pwMplsOutboundLsrXcIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation support non TE signaling of the outer tunnel. " OBJECT pwMplsOutboundTunnelIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundTunnelLclLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundTunnelPeerLSR MIN-ACCESS read-only DESCRIPTION "Write access is not required. " OBJECT pwMplsOutboundIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. A value other than zero MUST be supported if the implementation supports manually configured PW without MPLS outer tunnel. " ::= { pwMplsCompliances 2 } -- Units of conformance. pwMplsGroup OBJECT-GROUP OBJECTS { pwMplsMplsType, pwMplsExpBitsMode, pwMplsExpBits, pwMplsTtl, pwMplsLocalLdpID, pwMplsLocalLdpEntityIndex, pwMplsPeerLdpID, pwMplsStorageType } STATUS current DESCRIPTION "Collection of objects needed for PW over MPLS PSN configuration." ::= { pwMplsGroups 1 } Pseudo Wire (PW) Over MPLS June 2006 Management Information Base pwMplsOutboundMainGroup OBJECT-GROUP OBJECTS { pwMplsOutboundLsrXcIndex, pwMplsOutboundIfIndex, pwMplsOutboundTunnelTypeInUse } STATUS current DESCRIPTION "Collection of objects needed for outbound association of PW and MPLS tunnel." ::= { pwMplsGroups 2 } pwMplsOutboundTeGroup OBJECT-GROUP OBJECTS { pwMplsOutboundTunnelIndex, pwMplsOutboundTunnelInstance, pwMplsOutboundTunnelLclLSR, pwMplsOutboundTunnelPeerLSR } STATUS current DESCRIPTION "Collection of objects needed for outbound association of PW and MPLS TE tunnel." ::= { pwMplsGroups 3 } pwMplsInboundGroup OBJECT-GROUP OBJECTS { pwMplsInboundXcIndex } STATUS current DESCRIPTION "Collection of objects needed for inbound PW presentation. This group MUST be supported if PW signaling through LDP is used." ::= { pwMplsGroups 4 } pwMplsMappingGroup OBJECT-GROUP OBJECTS { pwMplsNonTeMappingPwIndex, pwMplsTeMappingPwIndex } STATUS current DESCRIPTION "Collection of objects needed for mapping association of PW and MPLS tunnel." ::= { pwMplsGroups 5 } Pseudo Wire (PW) Over MPLS June 2006 Management Information Base END -- -- Copyright (C) The Internet Society (2006). This document is -- subject to the rights, licenses and restrictions contained in BCP -- 78, and except as set forth therein, the authors retain all their -- rights. -- -- This document and the information contained herein are provided on -- an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE -- REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND -- THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, -- EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT -- THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR -- ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A -- PARTICULAR PURPOSE. -- -- 12 Intellectual Property Notice -- -- The IETF takes no position regarding the validity or scope of any -- Intellectual Property Rights or other rights that might be claimed -- to pertain to the implementation or use of the technology described -- in this document or the extent to which any license under such -- rights might or might not be available; nor does it represent that -- it has made any independent effort to identify any such rights. -- Information on the procedures with respect to rights in RFC -- documents can be found in BCP 78 and BCP 79. -- -- Copies of IPR disclosures made to the IETF Secretariat and any -- assurances of licenses to be made available, or the result of an -- attempt made to obtain a general license or permission for the use -- of such proprietary rights by implementers or users of this -- specification can be obtained from the IETF on-line IPR repository -- at http://www.ietf.org/ipr. -- -- The IETF invites any interested party to bring to its attention any -- copyrights, patents or patent applications, or other proprietary -- rights that may cover technology that may be required to implement -- this standard. Please address the information to the IETF at -- ietf-ipr@ietf.org.