-- extracted from draft-ietf-pwe3-pw-mib-06.txt -- at Fri Jul 22 06:35:26 2005 PW-STD-MIB DEFINITIONS ::= BEGIN IMPORTS NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Counter32, Counter64, TimeTicks FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC -- [RFC2579] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InterfaceIndexOrZero FROM IF-MIB -- [RFC2863] InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB -- [RFC3593] HCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed, HCPerfValidIntervals FROM HC-PerfHist-TC-MIB -- [RFC3705] PwIndexType, PwGroupID, PwIDType, PwOperStatusTC, PwTypeTC, PwAttachmentIdentifierType, PwCwStatusTC, PwCapabilities, PwStatus, PwFragSize, PwFragStatus, pwMIB FROM PW-TC-STD-MIB ; pwMIB MODULE-IDENTITY LAST-UPDATED "200406021200Z" -- 2 June 2004 12:00:00 GMT ORGANIZATION "Pseudo Wire Edge to Edge Emulation (PWE3) Working Group" CONTACT-INFO " David Zelig E-mail: davidz@corrigent.com Thomas D. Nadeau Email: tnadeau@cisco.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "This MIB module contains managed object definitions for Pseudo Wire operation as in [RFC3985][RFC3931][PWCNTRL]. architecture', Martini, L., et al, 'Pseudowire Setup and Maintenance using LDP', and Townsley, M., et al, 'Layer Two Tunneling Protocol (Version 3)'. This MIB module enables the use of any underlying packet switched network (PSN). MIB nodules that will support PW operations over specific PSN types are defined in separate memos. The indexes for this MIB module are also used to index the PSN-specific tables and the PW-specific tables. The PW Type dictates which PW-specific MIB module to use. Copyright (C) The Internet Society (date). This version of this MIB module is part of RFC XXX; see the RFC itself for full legal notices. -- RFC Ed.: replace XXX with actual RFC number & remove this note " -- Revision history. REVISION "200406021200Z" -- 2 June 2004 12:00:00 GMT DESCRIPTION " published as draft-ietf-pw-mib-05. Changes from previous drafts: - FCS retention includes FCS size mismatch error. - Allow configuration of peer address when signaling protocol is not in use. - Adding DEFVAL to PwFragSize. " REVISION "200402031200Z" -- 3 February 2004 12:00:00 GMT DESCRIPTION " published as draft-ietf-pw-mib-04. Changes from previous draft: - Adding an option for PW stitching - pwAttachedPwIndex. - Removing unnecessary index from pwPeerMappingTable. - Adding 32 bit counter support across performance tables. - Changing pwIndexMappingVcIndex to read-create in order to enable an option for EMS control on pwIndex. - Add optional mapping of a pwIndex to an ifIndex. - remove RowStatus from mapping table. - Change time elapsed items to HCPerfTimeElapsed TC - Change current and interval counters to their respective TC from existing TC modules. - Add disable/enable control for pwDeletedNotification. - Change pwRemoteCwStatus to pwCwStatus, and it now represent both the signaling status whether CW is to be present or not. " REVISION "200312101200Z" -- 10 December 2003 12:00:00 EST DESCRIPTION " re-published as draft-ietf-pw-mib-03. Changes from previous draft: - Changing textual convention back to TruthValue where required for correct compilation. - Editing description clauses. - Adapting main description clause to MIB boilerplate. - Adapt MIB names to STD-MIB naming convention. - Add pwRemoteStatusCapable. - Add PW delete notification. - Add pwLastChanged. - Clarify usage of pwIndexMappingTable. " REVISION "200307211200Z" -- 21 July 2003 12:00:00 EST DESCRIPTION " published as draft-ietf-pw-mib-02. Changes from previous draft: 1) Aligned with draft-ietf-pwe3-control-protocol-02.txt 2) Add support for Generalized ID FEC Element option. 3) Add support for fragmentation status. 3) Add notifications and notification control. 4) Remove control word to service specific MIB modules. " REVISION "200205261200Z" -- 26 May 2002 12:00:00 EST DESCRIPTION "Moved to draft-ietf-00 status. Changes from previous draft: 1) Change name of pwPriority to pwSetUpPriority and added pwHoldingPriority. 2) Add pwIdMappingTable and pwPeersMappingTable to help ordered query of the MIB tables for EMS applications. 3) Clarification to work in progress objects. 4) Editorial and typos in descriptions. 5) Added pwPerfTotalDiscontinuityTime and pwPerfIntervalTimeElapsed. 6) Remove 32 bit counters. " REVISION "200201301200Z" -- 30 January 2002 12:00:00 EST DESCRIPTION " Changes from -01 draft: 1) Inbound and outbound clarification and name changes. 2) Removing pwPeerIpv4Addr and pwPeerIpv6Addr, replacing them with pwPeerAddr and adding type for address type selection. 3) Adding type for VC OperStatus. 4) Adding pwTimeElapsed and pwValidIntervals. " REVISION "200111071200Z" -- 7 November 2001 12:00:00 EST DESCRIPTION "Changes from -00 draft: 1) Remove VcInstance from tables indexes in order to simplify the MIB. 2) Removing APS 1+1 table. 3) Changing hdlcCisco to hdlc in pwType. 4) Add description of VC label at pending PW signaling stage. 5) Add interval valid object in interval performance tables. 6) Remove VC APS notification. 7) Change 'conservative'/'liberal' to 'strict'/'loose'. 8) Add objects for interface MTU, use of control word, interface string. 9) Ordering of objects based on functionality. 10) Update operation of pwOperStatus. " REVISION "200107111200Z" -- 11 July 2001 12:00:00 EST DESCRIPTION "draft-00 version" ::= { pwMIB 799 } -- RFC Editor: To be assigned by IANA -- the value 2 is requested for this -- specific Module. Please replace XXX -- with the assigned value. -- Top-level components of this MIB. -- Notifications pwNotifications OBJECT IDENTIFIER ::= { pwMIB 0 } -- Tables, Scalars pwObjects OBJECT IDENTIFIER ::= { pwMIB 1 } -- Conformance pwConformance OBJECT IDENTIFIER ::= { pwMIB 2 } -- PW Virtual Connection (VC) Table pwIndexNext OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for pwIndex when creating entries in the pwTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwIndex for a new entry in the pwTable, the manager issues a management protocol retrieval operation to obtain the current value of pwIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { pwObjects 1 } pwTable OBJECT-TYPE SYNTAX SEQUENCE OF PwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and status monitoring which are common to all service types and PSN types." ::= { pwObjects 2 } pwEntry OBJECT-TYPE SYNTAX PwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents a pseudo wire (PW) virtual connection (VC) across a packet network. It is indexed by pwIndex, which uniquely identifying a singular connection. A row is created by the operator or by the agent if the PW is created by non-SNMP application or due to autodiscovery process. None of the read-create objects values can be changed when pwRowStatus is in the active(1) state. Changes are allowed when the pwRowStatus is in notInService(2) or notReady(3) states only. If the operator need to change one of the values for an active row (for example in order to fix a mismatch in configuration between the local node and the peer), the pwRowStatus should be first changed to notInService(2), the objects may be changed now, and later to active(1) in order to re-initiate the signaling process with the new values in effect. " INDEX { pwIndex } ::= { pwTable 1 } PwEntry ::= SEQUENCE { pwIndex PwIndexType, pwType PwTypeTC, pwOwner INTEGER, pwPsnType INTEGER, pwSetUpPriority Integer32, pwHoldingPriority Integer32, pwPeerAddrType InetAddressType, pwPeerAddr InetAddress, pwAttachedPwIndex PwIndexType, pwIfIndex InterfaceIndexOrZero, pwID PwIDType, pwLocalGroupID PwGroupID, pwGroupAttachmentID PwAttachmentIdentifierType, pwLocalAttachmentID PwAttachmentIdentifierType, pwPeerAttachmentID PwAttachmentIdentifierType, pwCwPreference TruthValue, pwLocalIfMtu Unsigned32, pwLocalIfString TruthValue, pwLocalCapabAdvert PwCapabilities, pwRemoteGroupID PwGroupID, pwCwStatus PwCwStatusTC, pwRemoteIfMtu Unsigned32, pwRemoteIfString SnmpAdminString, pwRemoteCapabilities PwCapabilities, pwFragmentCfgSize PwFragSize, pwRmtFragCapability PwFragStatus, pwFcsRetentioncfg INTEGER, pwFcsRetentionStatus BITS, pwOutboundVcLabel Unsigned32, pwInboundVcLabel Unsigned32, pwName SnmpAdminString, pwDescr SnmpAdminString, pwCreateTime TimeStamp, pwUpTime TimeTicks, pwLastChange TimeTicks, pwAdminStatus INTEGER, pwOperStatus PwOperStatusTC, pwLocalStatus PwStatus, pwRemoteStatusCapable INTEGER, pwRemoteStatus PwStatus, pwTimeElapsed HCPerfTimeElapsed, pwValidIntervals HCPerfValidIntervals, pwRowStatus RowStatus, pwStorageType StorageType } pwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the conceptual row identifying a PW within this PW Emulation table." ::= { pwEntry 1 } pwType OBJECT-TYPE SYNTAX PwTypeTC MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicate the service to be carried over this PW. " ::= { pwEntry 2 } pwOwner OBJECT-TYPE SYNTAX INTEGER { manual (1), pwIdFecSignaling (2), -- PW signaling with PW ID FEC genFecSignaling (3), -- Generalized attachment FEC l2tpControlProtocol (4), other (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set by the operator to indicate the protocol responsible for establishing this PW. Value 'manual' is used in all cases where no maintenance protocol (PW signaling) is used to set-up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. The value 'pwIdFecSignaling' is used in case of signaling with the Pwid FEC element with LDP signaling, and 'genFecSignaling' is used of the generalized FEC with LDP is used for signaling purposes. The value 'l2tpControlProtocol' indicate the use of L2TP control protocol. Value 'other' is used for other types of signaling." ::= { pwEntry 3 } pwPsnType OBJECT-TYPE SYNTAX INTEGER { mpls (1), l2tp (2), ip (3), mplsOverIp (4), gre (5), other (6) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set by the operator to indicate the PSN type on which this PW will be carried. Based on this object, the relevant PSN table entries are created in the in the PSN specific MIB modules. For example, if mpls(1) is defined, the agent create an entry in pwMplsTable, which further define the MPLS PSN configuration. " ::= { pwEntry 4 } pwSetUpPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object define the relative set-up priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. Dropped VC will be set 'dormant' (as indicated in pwOperStatus). This value is significant if there are competing resources between VCs and the implementation support this feature. If not supported or not relevant, the value of zero MUST be used." DEFVAL { 0 } ::= { pwEntry 5 } pwHoldingPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object define the relative holding priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. Dropped VC will be set 'dormant' (as indicated in pwOperStatus). This value is significant if there are competing resources between PWs and the implementation support this feature. If not supported or not relevant, the value of zero MUST be used." DEFVAL { 0 } ::= { pwEntry 6 } pwPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown." DEFVAL { ipv4 } ::= { pwEntry 8 } pwPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object contain the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (pwPeerAddrType is 'unknown')." ::= { pwEntry 9 } pwAttachedPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-create STATUS current DESCRIPTION "If the PW is attached to another PW instead of a local native service, this item indicates the pwIndex of the attached PW, and the PW specific entry in the service MIB module MUST not be created. Otherwise, this object MUST be set to zero." DEFVAL { 0 } ::= { pwEntry 10 } pwIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "If the PW is represented in the ifTable as an ifIndex, this item holds the ifIndex of the PW in the ifTable, otherwise it MUST be set to zero." DEFVAL { 0 } ::= { pwEntry 11 } pwID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS read-create STATUS current DESCRIPTION "Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Applicable if pwOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise." REFERENCE "Martini, et al, ." ::= { pwEntry 12 } pwLocalGroupID OBJECT-TYPE SYNTAX PwGroupID MAX-ACCESS read-create STATUS current DESCRIPTION "Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if pwOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise." REFERENCE "Martini, et al, ." ::= { pwEntry 13 } pwGroupAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the attachment group identifier (AGI) this PW belongs too, which typically identifies the VPN ID. Applicable if pwOwner equal 'genFecSignaling'. Should be set to NULL (zero length) if not applicable." REFERENCE "Martini, et al, ." ::= { pwEntry 14 } pwLocalAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the SAII for outgoing signaling messages and the TAII in the incoming messages from the peer. Applicable if pwOwner equal 'genFecSignaling'. Should be set to NULL (zero length) if not applicable. " REFERENCE "Martini, et al, ." ::= { pwEntry 15 } pwPeerAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the peer forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoing signaling messages and the SAII in the incoming messages from the peer. Applicable if pwOwner equal 'genFecSignaling'. Should be set to NULL (zero length) if not applicable. " REFERENCE "Martini, et al, ." ::= { pwEntry 16 } pwCwPreference OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Defines if the control word will be sent with each packet by the local node. Some PW types mandate the use of control word, and is such cases the value configured has no effect on the existence of the control word." REFERENCE "Martini, et al, ." DEFVAL { false } ::= { pwEntry 17 } pwLocalIfMtu OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "If not equal zero, the optional IfMtu object in the signaling protocol will be sent with this value, representing the locally supported MTU size over the interface (or the virtual interface) associated with the PW." REFERENCE "Martini, et al, ." DEFVAL { 0 } ::= { pwEntry 18 } pwLocalIfString OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Each PW is associated to an interface (or a virtual interface) in the ifTable of the node as part of the service configuration. This object defines if the maintenance protocol will send the interface's name as appears on the ifTable in the name object as part of the maintenance protocol. If set to false, the optional element will not be sent." REFERENCE "Martini, et al, ." DEFVAL { false } ::= { pwEntry 19 } pwLocalCapabAdvert OBJECT-TYPE SYNTAX PwCapabilities MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the capabilities to be advertised by this node to the peer." REFERENCE "Martini, et al, ." ::= { pwEntry 20 } pwRemoteGroupID OBJECT-TYPE SYNTAX PwGroupID MAX-ACCESS read-only STATUS current DESCRIPTION "Obtained from the Group ID field as received via the signaling protocol used for VC setup, zero if not used. Value of 0xFFFF shall be used if the object is yet to be defined by the PW maintenance protocol." REFERENCE "Martini, et al, ." ::= { pwEntry 21 } pwCwStatus OBJECT-TYPE SYNTAX PwCwStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both signaling or manual configuration indicates if CW is to be present or not for this PW. " REFERENCE "Martini, et al, . " ::= { pwEntry 22 } pwRemoteIfMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote interface MTU as (optionally) received from the remote node via the maintenance protocol. Should be zero if this parameter is not available or not used." REFERENCE "Martini, et al, ." ::= { pwEntry 23 } pwRemoteIfString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the interface description string as received by the maintenance protocol, MUST be NULL string if not applicable or not known yet." REFERENCE "Martini, et al, ." ::= { pwEntry 24 } pwRemoteCapabilities OBJECT-TYPE SYNTAX PwCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the capabilities as advertised by the peer." REFERENCE "Martini, et al, ." ::= { pwEntry 25 } pwFragmentCfgSize OBJECT-TYPE SYNTAX PwFragSize MAX-ACCESS read-create STATUS current DESCRIPTION "If set to value other than zero, indicates that fragmentation is desired for this PW." REFERENCE "Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly' - work in progress" DEFVAL { 0 } -- I.e. fragmentation not desired ::= { pwEntry 26 } pwRmtFragCapability OBJECT-TYPE SYNTAX PwFragStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the fragmentation based on the local configuration and the peer capabilities as advertised by the peer if control protocol is used." REFERENCE "Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly' - work in progress" ::= { pwEntry 27 } pwFcsRetentioncfg OBJECT-TYPE SYNTAX INTEGER { fcsRetentionDisable (1), fcsRetentionEnable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The local configuration of FCS retention for this PW. FCS retention can be configured for PW types HDLC, PPP and Ethernet only. If the agent does not support FCS retention the error should be configured in pwFcsRetentionStatus." REFERENCE "Malis A., et al., 'PWE3 Frame Check Sequence Retention' - work in progress" DEFVAL { fcsRetentionDisable } ::= { pwEntry 28 } pwFcsRetentionStatus OBJECT-TYPE SYNTAX BITS { remoteIndicationUnknown (0), remoteRequestFcsRetention (1), fcsRetentionEnabled (2), fcsRetentionDisabled (3), localFcsRetentionCfgErr (4), fcsRetentionFcsSizeMismatch (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the FCS retention negotiation process based on local configuration and the remote advertisement. remoteIndicationUnknown - set if a FEC has not been received from the remote. remoteRequestFcsRetention - indicates that the peer has requested for FCS retention. FCS retention will be used if the local node is capable and configured to use it for this PW. fcsRetentionEnabled - FCS retention is enabled (both peers were configured for FCS retention for signaled PW, or the local node is configured and capable for FCS retention. fcsRetentionDisabled - FCS retention is disabled (not configured locally or not advertised by the peer). localFcsRetentionCfgErr - Set if the local node has been configured for FCS retention but is not capable to support it. fcsRetentionFcsSizeMismatch - Set if there is a FCS size mismatch between the loacl and the peer node. " REFERENCE "Malis A., et al., 'PWE3 Frame Check Sequence Retention' - work in progress" ::= { pwEntry 29 } pwOutboundVcLabel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The PW label used in the outbound direction (i.e. toward the PSN). It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF." ::= { pwEntry 30 } pwInboundVcLabel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The PW label used in the inbound direction (i.e. packets received from the PSN. It may be set up manually if owner is 'manual' or automatically otherwise. Examples: For MPLS PSN, it represents the 20 bits of PW tag, for L2TP it represent the 32 bits Session ID. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF." ::= { pwEntry 31 } pwName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The canonical name assigned to the PW." ::= { pwEntry 32 } pwDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about the PW. If there is no description this object contains a zero length string." ::= { pwEntry 33 } pwCreateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "System time when this PW was created." ::= { pwEntry 34 } pwUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the total time this PW operStatus has been Up(1)." ::= { pwEntry 35 } pwLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time the PW entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { pwEntry 36 } pwAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } MAX-ACCESS read-create STATUS current DESCRIPTION "The desired operational status of this PW." ::= { pwEntry 37 } pwOperStatus OBJECT-TYPE SYNTAX PwOperStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the operational status of the PW, it does not reflect however the status of the CE bound interface. It is set to down only if pwNotForwarding, psnFacingPwRxFault, or psnFacingPwTxFault indications are set in pwLocalStatus or pwRemoteStatus. It indicates 'lowerLayerDown' if the only reason for not being in the 'up' state is either outer tunnel or physical layer down of the network side is in the down state. All other states are declared base on the description in the textual convention. " ::= { pwEntry 38 } pwLocalStatus OBJECT-TYPE SYNTAX PwStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of the PW in the local node. The various indications in this object should be available independent of the ability of the local node to advertise them or the remote node to accept these status indications through the control protocol. " ::= { pwEntry 39 } pwRemoteStatusCapable OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), notYetKnown (2), remoteCapable (3), remoteNotCapable (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the remote node capability to advertise the PW status notification. notAppicable should be reported for manually set PW, or if the local node is not capable of sending the status notification object. notYetKnown should be reported if the signaling protocol has not yet finished the process of capability determination. remoteCapable and remoteNotcapable should be reported based on the initial signaling exchange that has determined the remote node capability. " ::= { pwEntry 40 } pwRemoteStatus OBJECT-TYPE SYNTAX PwStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of the PW as was advertised by the remote. If the remote is not capable of advertising the status object, or the local node is not able to accept the status object through signaling, then the applicable bit is 'pwNotForwarding' which is set if the remote has sent label release or label withdraw for this PW. " ::= { pwEntry 41 } pwTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current interval measurement period." ::= { pwEntry 42 } pwValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected." ::= { pwEntry 43 } pwRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state." ::= { pwEntry 44 } pwStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { pwEntry 45 } -- End of PW Virtual Connection Table -- PW Performance Table. pwPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW performance information for the current interval." ::= { pwObjects 3 } pwPerfCurrentEntry OBJECT-TYPE SYNTAX PwPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW." INDEX { pwIndex } ::= { pwPerfCurrentTable 1 } PwPerfCurrentEntry ::= SEQUENCE { pwPerfCurrentInHCPackets HCPerfCurrentCount, pwPerfCurrentInHCBytes HCPerfCurrentCount, pwPerfCurrentOutHCPackets HCPerfCurrentCount, pwPerfCurrentOutHCBytes HCPerfCurrentCount, pwPerfCurrentInPackets PerfCurrentCount, pwPerfCurrentInBytes PerfCurrentCount, pwPerfCurrentOutPackets PerfCurrentCount, pwPerfCurrentOutBytes PerfCurrentCount } pwPerfCurrentInHCPackets OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 1 } pwPerfCurrentInHCBytes OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 2 } pwPerfCurrentOutHCPackets OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 3 } pwPerfCurrentOutHCBytes OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 4 } pwPerfCurrentInPackets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 32 bit version of pwPerfCurrentInHCPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 5 } pwPerfCurrentInBytes OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentInHCBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 6 } pwPerfCurrentOutPackets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 7 } pwPerfCurrentOutBytes OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 8 } -- End of PW Perf current Table -- PW Performance Interval Table. pwPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW performance information for each interval." ::= { pwObjects 4 } pwPerfIntervalEntry OBJECT-TYPE SYNTAX PwPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created agent for every PW." INDEX { pwIndex, pwPerfIntervalNumber } ::= { pwPerfIntervalTable 1 } PwPerfIntervalEntry ::= SEQUENCE { pwPerfIntervalNumber Integer32, pwPerfIntervalValidData TruthValue, pwPerfIntervalTimeElapsed HCPerfTimeElapsed, pwPerfIntervalInHCPackets HCPerfIntervalCount, pwPerfIntervalInHCBytes HCPerfIntervalCount, pwPerfIntervalOutHCPackets HCPerfIntervalCount, pwPerfIntervalOutHCBytes HCPerfIntervalCount, pwPerfIntervalInPackets PerfIntervalCount, pwPerfIntervalInBytes PerfIntervalCount, pwPerfIntervalOutPackets PerfIntervalCount, pwPerfIntervalOutBytes PerfIntervalCount } pwPerfIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 to 32. The maximum range of N is 1 through 96. " REFERENCE "Tesink, K. 'Definitions of Managed Objects for the SONET/SDH Interface Type', RFC 2558" ::= { pwPerfIntervalEntry 1 } pwPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwPerfIntervalEntry 2 } pwPerfIntervalTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of this interval in seconds." ::= { pwPerfIntervalEntry 3 } pwPerfIntervalInHCPackets OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInPackets, if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 4 } pwPerfIntervalInHCBytes OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInBytes, if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 5 } pwPerfIntervalOutHCPackets OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutPackets, if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 6 } pwPerfIntervalOutHCBytes OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutBytes, if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 7 } pwPerfIntervalInPackets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of packets received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalInHCPackets if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 8 } pwPerfIntervalInBytes OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of bytes received by this PW during the interval. It MUST be equal to the least significant 32 bits of if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 9 } pwPerfIntervalOutPackets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of packets sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCPackets if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 10 } pwPerfIntervalOutBytes OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of bytes sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCBytes if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 11 } -- End of PW Performance Interval Table -- PW Performance Total Table. pwPerfTotalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW Performance information from PW start time or management application reset." ::= { pwObjects 5 } pwPerfTotalEntry OBJECT-TYPE SYNTAX PwPerfTotalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW. pwPerfTotalDiscontinuityTime indicates the time of the last discontinuity in any of these objects." INDEX { pwIndex } ::= { pwPerfTotalTable 1 } PwPerfTotalEntry ::= SEQUENCE { pwPerfTotalInHCPackets Counter64, pwPerfTotalInHCBytes Counter64, pwPerfTotalOutHCPackets Counter64, pwPerfTotalOutHCBytes Counter64, pwPerfTotalInPackets Counter32, pwPerfTotalInBytes Counter32, pwPerfTotalOutPackets Counter32, pwPerfTotalOutBytes Counter32, pwPerfTotalDiscontinuityTime TimeStamp } pwPerfTotalInHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of packets received by the PW (from the PSN). This is the 64 bit version of pwPerfTotalInPackets, if pwPerfTotalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 1 } pwPerfTotalInHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of bytes received by the PW (from the PSN). This is the 64 bit version of pwPerfTotalInBytes, if pwPerfTotalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 2 } pwPerfTotalOutHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of packets forwarded by the PW (to the PSN). This is the 64 bit version of pwPerfTotalOutPackets, if pwPerfTotalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 3 } pwPerfTotalOutHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of bytes forwarded by the PW (to the PSN). This is the 64 bit version of pwPerfTotalOutBytes, if pwPerfTotalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 4 } pwPerfTotalInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of packets received by this PW. It MUST be equal to the least significant 32 bits of pwPerfTotalInHCPackets if pwPerfTotalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 5 } pwPerfTotalInBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of bytes received by this PW. It MUST be equal to the least significant 32 bits of if pwPerfTotalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 6 } pwPerfTotalOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of packets sent by this PW. It MUST be equal to the least significant 32 bits of pwPerfTotalOutHCPackets if pwPerfTotalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 7 } pwPerfTotalOutBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the total number of bytes sent by this PW. It MUST be equal to the least significant 32 bits of pwPerfTotalOutHCBytes if pwPerfTotalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfTotalEntry 8 } pwPerfTotalDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this row Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value." ::= { pwPerfTotalEntry 9 } -- End of PW Perf Total Table -- Error counter scalar pwPerfTotalErrorPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of error at the PW processing level, for example packets received with unknown PW label." ::= { pwObjects 6 } -- Reverse mapping tables -- The PW ID mapping table pwIndexMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table enables the reverse mapping the unique PWid parameters and the pwIndex. The table is not applicable for PW created manually or by using the generalized FEC." ::= { pwObjects 7 } pwIndexMappingEntry OBJECT-TYPE SYNTAX PwIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table MUST be created by the agent for every PW created by the pwTable for which pwOwner equals pwIdFecSignaling." INDEX { pwIndexMappingVcType, pwIndexMappingVcID, pwIndexMappingPeerAddrType, pwIndexMappingPeerAddr } ::= { pwIndexMappingTable 1 } PwIndexMappingEntry ::= SEQUENCE { pwIndexMappingVcType PwTypeTC, pwIndexMappingVcID PwIDType, pwIndexMappingPeerAddrType InetAddressType, pwIndexMappingPeerAddr InetAddress, pwIndexMappingVcIndex PwIndexType } pwIndexMappingVcType OBJECT-TYPE SYNTAX PwTypeTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW type (indicates the service) of this PW." ::= { pwIndexMappingEntry 1 } pwIndexMappingVcID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW ID of this PW. Zero if the PW is configured manually." ::= { pwIndexMappingEntry 2 } pwIndexMappingPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwIndexMappingEntry 3 } pwIndexMappingPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwIndexMappingEntry 4 } pwIndexMappingVcIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represents the PW in the pwTable." ::= { pwIndexMappingEntry 5 } -- End of the PW ID mapping table -- The peer mapping table pwPeerMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPeerMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides reverse mapping of the existing PW based on PW type and PW ID ordering. This table is typically useful for EMS ordered query of existing PWs." ::= { pwObjects 8 } pwPeerMappingEntry OBJECT-TYPE SYNTAX PwPeerMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW configured in pwTable. Implementors need to be aware that if the value of the pwPeerMappingPeerAddr (an OID) or pwPeerMappingVcID (an OID) (or both combined) has more than 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3." INDEX { pwPeerMappingPeerAddrType, pwPeerMappingPeerAddr, pwPeerMappingVcType, pwPeerMappingVcID } ::= { pwPeerMappingTable 1 } PwPeerMappingEntry ::= SEQUENCE { pwPeerMappingPeerAddrType InetAddressType, pwPeerMappingPeerAddr InetAddress, pwPeerMappingVcType PwTypeTC, pwPeerMappingVcID PwIDType, pwPeerMappingVcIndex PwIndexType } pwPeerMappingPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwPeerMappingEntry 1 } pwPeerMappingPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwPeerMappingEntry 2 } pwPeerMappingVcType OBJECT-TYPE SYNTAX PwTypeTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW type (indicates the service) of this PW." ::= { pwPeerMappingEntry 3 } pwPeerMappingVcID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW ID of this PW. Zero if the PW is configured manually." ::= { pwPeerMappingEntry 4 } pwPeerMappingVcIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represents the PW in the pwTable." ::= { pwPeerMappingEntry 5 } -- End of the peer mapping table -- End of reverse mapping tables pwUpDownNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwUp and pwDown notifications; otherwise these notifications are not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { false } ::= { pwObjects 9 } pwDeletedNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwDeleted notification; otherwise this notification is not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { false } ::= { pwObjects 10 } pwNotifRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the maximum number of PW notifications that can be emitted from the device per second." ::= { pwObjects 11 } -- Notifications - PW pwDown NOTIFICATION-TYPE OBJECTS { pwOperStatus, --start of range pwOperStatus --end of range } STATUS current DESCRIPTION "This notification is generated when the pwOperStatus object for one or more contiguous entries in pwTable are about to enter the down(2) state from some other state. The included values of pwOperStatus MUST all be set equal to this down(2) state. The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the down(2) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be identical." ::= { pwNotifications 1 } pwUp NOTIFICATION-TYPE OBJECTS { pwOperStatus, --start of range pwOperStatus --end of range } STATUS current DESCRIPTION "This notification is generated when the pwOperStatus object for one or more contiguous entries in pwTable are about to enter the up(1) state from some other state. The included values of pwOperStatus MUST both be set equal to this new state (i.e: up(1)). The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be the identical." ::= { pwNotifications 2 } pwDeleted NOTIFICATION-TYPE OBJECTS { pwType, pwID, pwPeerAddrType, pwPeerAddr } STATUS current DESCRIPTION "This notification is generated when the PW has been deleted, i.e. when the pwRowStatus has been set to destroy(6), the PW has been deleted by a non-MIB application or due to auto discovery process. " ::= { pwNotifications 3 } -- End of notifications. -- conformance information pwGroups OBJECT IDENTIFIER ::= { pwConformance 1 } pwCompliances OBJECT IDENTIFIER ::= { pwConformance 2 } -- Compliance requirement for fully compliant implementations. pwModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide full support for PW MIB Module. Such devices can then be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwBasicGroup, pwPerformanceGeneralGroup, pwPeformanceTotalGroup } GROUP pwNotificationGroup DESCRIPTION "This group is only mandatory for those implementations which can efficiently implement the notifications contained in this group." GROUP pwPwIdGroup DESCRIPTION "This group is only mandatory for implementations that support the PW ID FEC. " GROUP pwGeneralizedFecGroup DESCRIPTION "This group is only mandatory for implementations that support the generalized PW FEC. " GROUP pwFcsGroup DESCRIPTION "This group is only mandatory for implementations that support FCS retention." GROUP pwFragGroup DESCRIPTION "This group is only mandatory for implementations that support PW fragmentation. " GROUP pwPwStatusGroup DESCRIPTION "This group is only mandatory for implementations that support PW status notification. " GROUP pwGetNextGroup DESCRIPTION "This group is only mandatory for implementations where the pwIndex may be any arbitrary value and the EMS would require retrieval of the next free index." GROUP pwPriorityGroup DESCRIPTION "This group is only mandatory for implementations that support the controlling the PW setup and holding priority." GROUP pwAttachmentGroup DESCRIPTION "This group is only mandatory for implementations that support attachment of two PWs (PW stitching)." GROUP pwHCPeformanceTotalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the total performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwPerformanceIntervalGeneralGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minutes intervals." GROUP pwPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minutes intervals." GROUP pwHCPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the interval performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwMappingTablesGroup DESCRIPTION "This group is only mandatory for implementations that support reverse mapping of PW indexes to the pwIndex and the peer mapping table." GROUP pwNotificationControlGroup DESCRIPTION "This group is only mandatory for implementations that support the PW notifications." OBJECT pwAdminStatus SYNTAX INTEGER { up(1), down(2) } DESCRIPTION "The support of the value testing(3) is not required." OBJECT pwOperStatus SYNTAX INTEGER { up(1), down(2), notPresent(6), lowerLayerDown(7) } DESCRIPTION "The support of the values testing(3), unknown(4), and dormant(5) is not required." OBJECT pwRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required. Support of notReady is not required for implementations that do not support signaling, or if it is guaranteed that the conceptual row has all the required information to create the PW when the row has been created by the agent." OBJECT pwPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1) } DESCRIPTION "Only unknown(0) and ipv4(1) is required." OBJECT pwPeerAddr SYNTAX InetAddress (SIZE(0|4)) DESCRIPTION "An implementation is only required to support 0, 4 address sizes." ::= { pwCompliances 1 } -- Compliance requirement for read only compliant implementations. pwModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read only support for PW MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwBasicGroup, pwPeformanceTotalGroup } GROUP pwNotificationGroup DESCRIPTION "This group is only mandatory for those implementations which can efficiently implement the notifications contained in this group." GROUP pwPwIdGroup DESCRIPTION "This group is only mandatory for implementations that support the PW ID FEC. " GROUP pwGeneralizedFecGroup DESCRIPTION "This group is only mandatory for implementations that support the generalized PW FEC. " GROUP pwFcsGroup DESCRIPTION "This group is only mandatory for implementations that support FCS retention." GROUP pwFragGroup DESCRIPTION "This group is only mandatory for implementations that support PW fragmentation. " GROUP pwPwStatusGroup DESCRIPTION "This group is only mandatory for implementations that support PW status notification. " GROUP pwGetNextGroup DESCRIPTION "This group is only mandatory for implementations where the pwIndex may be any arbitary value and the EMS would require retrieval of the next free index." GROUP pwPriorityGroup DESCRIPTION "This group is only mandatory for implementations that support the controling the PW setup and holding priority." GROUP pwAttachmentGroup DESCRIPTION "This group is only mandatory for implementations that support attachment of two PWs (PW stitching)." GROUP pwHCPeformanceTotalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the total performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwPerformanceIntervalGeneralGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minutes intervals." GROUP pwPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minutes intervals." GROUP pwHCPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the interval performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwMappingTablesGroup DESCRIPTION "This group is only mandatory for implementations that support reverse mapping of PW indexes to the pwIndex and the peer mapping table." GROUP pwNotificationControlGroup DESCRIPTION "This group is only mandatory for implementations that support the PW notifications." OBJECT pwType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwOwner MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPsnType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwSetUpPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwHoldingPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. Only unknown(0) and ipv4(1) is required." OBJECT pwPeerAddr SYNTAX InetAddress (SIZE(0|4)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 0, 4 address sizes." OBJECT pwAttachedPwIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalGroupID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwGroupAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPeerAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCwPreference MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalIfMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalIfString MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalCapabAdvert MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwFragmentCfgSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwFcsRetentioncfg MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwOutboundVcLabel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwInboundVcLabel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwDescr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwAdminStatus SYNTAX INTEGER { up(1), down(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. The support of value testing(3) is not required." OBJECT pwOperStatus SYNTAX INTEGER { up(1), down(2), notPresent(6), lowerLayerDown(7) } DESCRIPTION "The support of the values testing(3), unknown(4), and is not required." OBJECT pwRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwUpDownNotifEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwDeletedNotifEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwNotifRate MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pwCompliances 2 } -- Units of conformance. pwBasicGroup OBJECT-GROUP OBJECTS { pwType, pwOwner, pwPsnType, pwPeerAddrType, pwPeerAddr, pwIfIndex, pwID, pwLocalGroupID, pwCwPreference, pwLocalIfMtu, pwLocalIfString, pwLocalCapabAdvert, pwRemoteGroupID, pwCwStatus, pwRemoteIfMtu, pwRemoteIfString, pwOutboundVcLabel, pwInboundVcLabel, pwName, pwDescr, pwCreateTime, pwUpTime, pwLastChange, pwAdminStatus, pwOperStatus, pwLocalStatus, pwRowStatus, pwStorageType } STATUS current DESCRIPTION "Collection of objects that are required in all implementations that support the PW MIB module." ::= { pwGroups 1 } pwPwIdGroup OBJECT-GROUP OBJECTS { pwID } STATUS current DESCRIPTION "Collection of objects required for PW ID configuration and signaling." ::= { pwGroups 2 } pwGeneralizedFecGroup OBJECT-GROUP OBJECTS { pwGroupAttachmentID, pwLocalAttachmentID, pwPeerAttachmentID } STATUS current DESCRIPTION "Collection of objects required for generalized FEC configuration and signaling." ::= { pwGroups 3 } pwFcsGroup OBJECT-GROUP OBJECTS { pwFcsRetentioncfg, pwFcsRetentionStatus } STATUS current DESCRIPTION "Collection of objects required for FCS retention configuration and signaling." ::= { pwGroups 4 } pwFragGroup OBJECT-GROUP OBJECTS { pwFragmentCfgSize, pwRmtFragCapability } STATUS current DESCRIPTION "Collection of objects required for fragmentation configuration and signaling." ::= { pwGroups 5 } pwPwStatusGroup OBJECT-GROUP OBJECTS { pwRemoteCapabilities, pwRemoteStatusCapable, pwRemoteStatus } STATUS current DESCRIPTION "Collection of objects required for PW status configuration and signaling." ::= { pwGroups 6 } pwGetNextGroup OBJECT-GROUP OBJECTS { pwIndexNext } STATUS current DESCRIPTION "Collection of objects for getting the next available index." ::= { pwGroups 7 } pwPriorityGroup OBJECT-GROUP OBJECTS { pwSetUpPriority, pwHoldingPriority } STATUS current DESCRIPTION "Collection of objects for controlling the PW setup and holding priority." ::= { pwGroups 8 } pwAttachmentGroup OBJECT-GROUP OBJECTS { pwAttachedPwIndex } STATUS current DESCRIPTION "Collection of objects for PW configuration and signaling." ::= { pwGroups 9 } pwPerformanceGeneralGroup OBJECT-GROUP OBJECTS { pwPerfTotalDiscontinuityTime, pwPerfTotalErrorPackets } STATUS current DESCRIPTION "Collection of general objects needed for managing the total running performance parameters." ::= { pwGroups 10 } pwPeformanceTotalGroup OBJECT-GROUP OBJECTS { pwPerfTotalInPackets, pwPerfTotalInBytes, pwPerfTotalOutPackets, pwPerfTotalOutBytes } STATUS current DESCRIPTION "Collection of 32 bits objects needed for PW running total performance collection." ::= { pwGroups 11 } pwHCPeformanceTotalGroup OBJECT-GROUP OBJECTS { pwPerfTotalInHCPackets, pwPerfTotalInHCBytes, pwPerfTotalOutHCPackets, pwPerfTotalOutHCBytes } STATUS current DESCRIPTION "Collection of HC objects needed for PW running total performance collection." ::= { pwGroups 12 } pwPerformanceIntervalGeneralGroup OBJECT-GROUP OBJECTS { pwTimeElapsed, pwValidIntervals, pwPerfIntervalValidData, pwPerfIntervalTimeElapsed } STATUS current DESCRIPTION "Collection of general objects needed for managing the interval performance parameters." ::= { pwGroups 13 } pwPeformanceIntervalGroup OBJECT-GROUP OBJECTS { pwPerfCurrentInPackets, pwPerfCurrentInBytes, pwPerfCurrentOutPackets, pwPerfCurrentOutBytes, pwPerfIntervalInPackets, pwPerfIntervalInBytes, pwPerfIntervalOutPackets, pwPerfIntervalOutBytes } STATUS current DESCRIPTION "Collection of 32 bits objects needed for PW performance collection in 15 minutes intervals." ::= { pwGroups 14 } pwHCPeformanceIntervalGroup OBJECT-GROUP OBJECTS { pwPerfCurrentInHCPackets, pwPerfCurrentInHCBytes, pwPerfCurrentOutHCPackets, pwPerfCurrentOutHCBytes, pwPerfIntervalInHCPackets, pwPerfIntervalInHCBytes, pwPerfIntervalOutHCPackets, pwPerfIntervalOutHCBytes } STATUS current DESCRIPTION "Collection of HC objects needed for PW performance collection in 15 minutes intervals." ::= { pwGroups 15 } pwMappingTablesGroup OBJECT-GROUP OBJECTS { pwIndexMappingVcIndex, pwPeerMappingVcIndex } STATUS current DESCRIPTION "Collection of objects contained in the reverse mapping tables." ::= { pwGroups 16 } pwNotificationControlGroup OBJECT-GROUP OBJECTS { pwUpDownNotifEnable, pwDeletedNotifEnable, pwNotifRate } STATUS current DESCRIPTION "Collection of objects for controlling the PW notifications." ::= { pwGroups 17 } pwNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { pwUp, pwDown, pwDeleted } STATUS current DESCRIPTION "Collection PW notifications objects." ::= { pwGroups 18 } END -- -- Copyright (C) The Internet Society (2005). This document is -- subject to the rights, licenses and restrictions contained in BCP -- 78, and except as set forth therein, the authors retain all their -- rights. -- -- This document and the information contained herein are provided -- on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE -- REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND -- THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, -- EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT -- THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR -- ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A -- PARTICULAR PURPOSE. --