-- extracted from draft-ietf-pwe3-pw-mib-09.txt -- at Tue Oct 24 06:07:23 2006 PW-STD-MIB DEFINITIONS ::= BEGIN IMPORTS NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Counter32, Counter64, TimeTicks, transmission FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] TruthValue, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC -- [RFC2579] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InterfaceIndexOrZero FROM IF-MIB -- [RFC2863] InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB -- [RFC3593] HCPerfCurrentCount, HCPerfIntervalCount, HCPerfTimeElapsed, HCPerfValidIntervals FROM HC-PerfHist-TC-MIB -- [RFC3705] PwIndexType, PwIndexOrZeroType, PwGroupID, PwIDType, PwOperStatusTC, PwAttachmentIdentifierType, PwCwStatusTC, PwStatus, PwFragSize, PwFragStatus FROM PW-TC-STD-MIB -- [RFCxxxx] -- RFC Editor: Please replace XXXX with RFC number and remove this -- note. IANAPwTypeTC, IANAPwPsnTypeTC, IANAPwCapabilities FROM IANA-PWE3-MIB -- [RFCxxxx] -- RFC Editor: Please replace XXXX with RFC number and remove this -- note. ; pwStdMIB MODULE-IDENTITY LAST-UPDATED "200610161200Z" -- 16 October 2006 12:00:00 GMT ORGANIZATION "Pseudo Wire Edge-to-Edge Emulation (PWE3) Working Group" CONTACT-INFO " David Zelig E-mail: davidz@corrigent.com Thomas D. Nadeau Email: tnadeau@cisco.com The PWE3 Working Group (email distribution pwe3@ietf.org, http://www.ietf.org/html.charters/pwe3-charter.html) " DESCRIPTION "Copyright (C) The Internet Society (2006). The initial version of this MIB module was published in RFC XXXX. -- RFC Editor: Please replace XXXX with RFC number and remove this -- note. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for pseudo-wire operation as in Bryant, S. and P. Pate, 'Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture' [RFC3985], Martini, L., et al, 'Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP)' [RFC4447], and Townsley, M., et al, 'Layer Two Tunneling Protocol (Version 3)' [RFC3931]. This MIB module enables the use of any underlying packet switched network (PSN). MIB nodules that will support PW operations over specific PSN types are defined in separate memos. The indexes for this MIB module are also used to index the PSN-specific tables and the PW-specific tables. The PW Type dictates which PW-specific MIB module to use. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC XXX; see the RFC itself for full legal notices. -- RFC Ed.: replace XXX with actual RFC number & remove this note " -- Revision history. REVISION "200610161200Z" -- 16 October 2006 12:00:00 GMT DESCRIPTION "Initial version published as part of RFC YYYY." -- RFC Editor: please replace YYYY with IANA assigned value, and -- delete this note. ::= { transmission XXXX } -- RFC Editor: please replace XXXX with IANA assigned value, and -- delete this note. -- Top-level components of this MIB. -- Notifications pwNotifications OBJECT IDENTIFIER ::= { pwStdMIB 0 } -- Tables, Scalars pwObjects OBJECT IDENTIFIER ::= { pwStdMIB 1 } -- Conformance pwConformance OBJECT IDENTIFIER ::= { pwStdMIB 2 } -- PW Virtual Connection Table pwIndexNext OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for pwIndex when creating entries in the pwTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwIndex for a new entry in the pwTable, the manager issues a management protocol retrieval operation. The agent will determine through its local policy when this index value will be made available for reuse." ::= { pwObjects 1 } pwTable OBJECT-TYPE SYNTAX SEQUENCE OF PwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies information for configuring and status monitoring which are common to all service types and PSN types." ::= { pwObjects 2 } pwEntry OBJECT-TYPE SYNTAX PwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table represents a pseudo-wire (PW) virtual connection across a packet network. It is indexed by pwIndex, which uniquely identifies a singular connection. A row is created by the operator or by the agent if the PW is created by non-SNMP application or due to autodiscovery process. None of the read-create objects values can be changed when pwRowStatus is in the active(1) state. Changes are allowed when the pwRowStatus is in notInService(2) or notReady(3) states only. If the operator need to change one of the values for an active row (for example in order to fix a mismatch in configuration between the local node and the peer), the pwRowStatus should be first changed to notInService(2), the objects may be changed now, and later to active(1) in order to re-initiate the signaling process with the new values in effect. " INDEX { pwIndex } ::= { pwTable 1 } PwEntry ::= SEQUENCE { pwIndex PwIndexType, pwType IANAPwTypeTC, pwOwner INTEGER, pwPsnType IANAPwPsnTypeTC, pwSetUpPriority Integer32, pwHoldingPriority Integer32, pwPeerAddrType InetAddressType, pwPeerAddr InetAddress, pwAttachedPwIndex PwIndexOrZeroType, pwIfIndex InterfaceIndexOrZero, pwID PwIDType, pwLocalGroupID PwGroupID, pwGroupAttachmentID PwAttachmentIdentifierType, pwLocalAttachmentID PwAttachmentIdentifierType, pwPeerAttachmentID PwAttachmentIdentifierType, pwCwPreference TruthValue, pwLocalIfMtu Unsigned32, pwLocalIfString TruthValue, pwLocalCapabAdvert IANAPwCapabilities, pwRemoteGroupID PwGroupID, pwCwStatus PwCwStatusTC, pwRemoteIfMtu Unsigned32, pwRemoteIfString SnmpAdminString, pwRemoteCapabilities IANAPwCapabilities, pwFragmentCfgSize PwFragSize, pwRmtFragCapability PwFragStatus, pwFcsRetentioncfg INTEGER, pwFcsRetentionStatus BITS, pwOutboundLabel Unsigned32, pwInboundLabel Unsigned32, pwName SnmpAdminString, pwDescr SnmpAdminString, pwCreateTime TimeStamp, pwUpTime TimeTicks, pwLastChange TimeTicks, pwAdminStatus INTEGER, pwOperStatus PwOperStatusTC, pwLocalStatus PwStatus, pwRemoteStatusCapable INTEGER, pwRemoteStatus PwStatus, pwTimeElapsed HCPerfTimeElapsed, pwValidIntervals HCPerfValidIntervals, pwRowStatus RowStatus, pwStorageType StorageType } pwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for the conceptual row identifying a PW within this PW Emulation table." ::= { pwEntry 1 } pwType OBJECT-TYPE SYNTAX IANAPwTypeTC MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicate the service to be carried over this PW. " ::= { pwEntry 2 } pwOwner OBJECT-TYPE SYNTAX INTEGER { manual (1), pwIdFecSignaling (2), -- PW signaling with PW ID FEC genFecSignaling (3), -- Generalized attachment FEC l2tpControlProtocol (4), other (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set by the operator to indicate the protocol responsible for establishing this PW. 'manual' is used in all cases where no maintenance protocol (PW signaling) is used to set-up the PW, i.e. require configuration of entries in the PW tables including PW labels, etc. 'pwIdFecSignaling' is used in case of signaling with the Pwid FEC element with LDP signaling. 'genFecSignaling' is used in case of LDP signaling with the generalized FEC. 'l2tpControlProtocol' indicates the use of L2TP control protocol. 'other' is used for other types of signaling." ::= { pwEntry 3 } pwPsnType OBJECT-TYPE SYNTAX IANAPwPsnTypeTC MAX-ACCESS read-create STATUS current DESCRIPTION "Set by the operator to indicate the PSN type. Based on this object, the relevant PSN table entries are created in the in the PSN specific MIB modules. It is not possible to change the value of this object after the row creation. " ::= { pwEntry 4 } pwSetUpPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines the relative set-up priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. Dropped PW will be set 'dormant' (as indicated in pwOperStatus). This value is significant if there are competing resources between PWs and the implementation support this feature. Equal priority handling with competing resources is implementation specific. " DEFVAL { 0 } ::= { pwEntry 5 } pwHoldingPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines the relative holding priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. Dropped PW will be set 'dormant' (as indicated in pwOperStatus). This value is significant if there are competing resources between PWs and the implementation support this feature. Equal priority handling with competing resources is implementation specific. " DEFVAL { 0 } ::= { pwEntry 6 } pwPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown. It is not possible to change the value of this object after the row creation." DEFVAL { ipv4 } ::= { pwEntry 8 } pwPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (pwPeerAddrType is 'unknown'). It is not possible to change the value of this object after the row creation." ::= { pwEntry 9 } pwAttachedPwIndex OBJECT-TYPE SYNTAX PwIndexOrZeroType MAX-ACCESS read-create STATUS current DESCRIPTION "If the PW is attached to another PW instead of a local native service, this item indicates the pwIndex of the attached PW, and the PW specific entry in the service MIB module MUST not be created. Otherwise, this object MUST be set to zero." DEFVAL { 0 } ::= { pwEntry 10 } pwIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "If the PW is represented in the ifTable as an ifIndex, this item holds the ifIndex of the PW in the ifTable, otherwise it MUST be set to zero." DEFVAL { 0 } ::= { pwEntry 11 } pwID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS read-create STATUS current DESCRIPTION "Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Applicable if pwOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', otherwiseshould be set to zero. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 12 } pwLocalGroupID OBJECT-TYPE SYNTAX PwGroupID MAX-ACCESS read-create STATUS current DESCRIPTION "Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. Applicable if pwOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', should be set to zero otherwise. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 13 } pwGroupAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the attachment group identifier (AGI) that this PW belongs too, which typically identifies the VPN ID. Applicable if pwOwner equal 'genFecSignaling'. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 14 } pwLocalAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the SAII for outgoing signaling messages and the TAII in the incoming messages from the peer. Applicable if pwOwner equal 'genFecSignaling'. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 15 } pwPeerAttachmentID OBJECT-TYPE SYNTAX PwAttachmentIdentifierType MAX-ACCESS read-create STATUS current DESCRIPTION "This object is an octet string representing the peer forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoing signaling messages and the SAII in the incoming messages from the peer. Applicable if pwOwner equal 'genFecSignaling'. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 16 } pwCwPreference OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Defines if the control word will be sent with each packet by the local node. Some PW types mandate the use of a control word, and in such cases the value configured for this object has no effect on the existence of the control word. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol.', RFC 4447." DEFVAL { false } ::= { pwEntry 17 } pwLocalIfMtu OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "If not equal to zero, the optional IfMtu object in the signaling protocol will be sent with this value, whihc represents the locally-supported MTU size over the interface (or the virtual interface) associated with the PW. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." DEFVAL { 0 } ::= { pwEntry 18 } pwLocalIfString OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "A PW MAY be associated to an interface (or a virtual interface) in the ifTable of the node as part of the service configuration. This object defines if the maintenance protocol will send the interface's name as appears on the ifTable in the name object as part of the maintenance protocol. If set to false, the optional element will not be sent." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." DEFVAL { false } ::= { pwEntry 19 } pwLocalCapabAdvert OBJECT-TYPE SYNTAX IANAPwCapabilities MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the capabilities to be advertised by this node to the peer. It is not possible to change the value of this object after the row creation." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 20 } pwRemoteGroupID OBJECT-TYPE SYNTAX PwGroupID MAX-ACCESS read-only STATUS current DESCRIPTION "Obtained from the Group ID field as received via the maintenance protocol used for PW setup, zero if not used. Value of 0xFFFF shall be used if the object is yet to be defined by the PW maintenance protocol." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 21 } pwCwStatus OBJECT-TYPE SYNTAX PwCwStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both signaling or manual configuration indicates if CW is to be present or not for this PW." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 22 } pwRemoteIfMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote interface MTU as (optionally) received from the remote node via the maintenance protocol. Should be zero if this parameter is not available or not used." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 23 } pwRemoteIfString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the interface description string as received by the maintenance protocol. It MUST be a NULL string if not applicable or not known yet." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 24 } pwRemoteCapabilities OBJECT-TYPE SYNTAX IANAPwCapabilities MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the capabilities as advertised by the peer." REFERENCE "Martini, et al, 'Pseudowire Setup and Maintenance using the Label Distribution Protocol', RFC 4447." ::= { pwEntry 25 } pwFragmentCfgSize OBJECT-TYPE SYNTAX PwFragSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "If set to a value other than zero, indicates that fragmentation is desired for this PW." REFERENCE "Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly', RFC 4623." DEFVAL { 0 } -- i.e. fragmentation not desired ::= { pwEntry 26 } pwRmtFragCapability OBJECT-TYPE SYNTAX PwFragStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the fragmentation based on the local configuration and the peer capabilities as advertised by the peer if control protocol is used." REFERENCE "Malis A., Townsley M., 'PWE3 Fragmentation and Reassembly', RFC 4623." ::= { pwEntry 27 } pwFcsRetentioncfg OBJECT-TYPE SYNTAX INTEGER { fcsRetentionDisable (1), fcsRetentionEnable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The local configuration of FCS retention for this PW. FCS retention can be configured for PW types HDLC, PPP and Ethernet only. If the agent does not support FCS retention the error MUST be reported in pwFcsRetentionStatus. It is not possible to change the value of this object after the row creation." REFERENCE "Malis A., et al., 'PWE3 Frame Check Sequence Retention' - work in progress" DEFVAL { fcsRetentionDisable } ::= { pwEntry 28 } pwFcsRetentionStatus OBJECT-TYPE SYNTAX BITS { remoteIndicationUnknown (0), remoteRequestFcsRetention (1), fcsRetentionEnabled (2), fcsRetentionDisabled (3), localFcsRetentionCfgErr (4), fcsRetentionFcsSizeMismatch (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the FCS retention negotiation process based on local configuration and the remote advertisement. remoteIndicationUnknown - set if a FEC has not been received from the remote. remoteRequestFcsRetention - indicates that the peer has requested for FCS retention. FCS retention will be used if the local node is capable and configured to use it for this PW. fcsRetentionEnabled - FCS retention is enabled (both peers were configured for FCS retention for signaled PW, or the local node is configured and capable for FCS retention for manually assigned PW). fcsRetentionDisabled - FCS retention is disabled (not configured locally or not advertised by the peer). localFcsRetentionCfgErr - Set if the local node has been configured for FCS retention but is not capable to support it. fcsRetentionFcsSizeMismatch - Set if there is an FCS size mismatch between the local and the peer node. " REFERENCE "Malis A., et al., 'PWE3 Frame Check Sequence Retention' - work in progress" ::= { pwEntry 29 } pwOutboundLabel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The PW label used in the outbound direction (i.e. toward the PSN). It may be set up manually if owner is 'manual', otherwise automatically. For MPLS, MPLS over IP or MPLS over GRE PSN, it represents the 20 bits of PW tag, for L2TP it represents the 32 bits Session ID and for IP PSN it represents the destination UDP port number. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF." ::= { pwEntry 30 } pwInboundLabel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The PW label used in the inbound direction (i.e. packets received from the PSN). It may be set up manually if owner is 'manual',otherwise automatically. For MPLS, MPLS over IP or MPLS over GRE PSN, it represents the 20 bits of PW tag, for L2TP it represents the 32 bits Session ID and for IP PSN it represents the source UDP port number. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF." ::= { pwEntry 31 } pwName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The canonical name assigned to the PW." ::= { pwEntry 32 } pwDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about the PW. If there is no description this object contains a zero length string." ::= { pwEntry 33 } pwCreateTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "System time when this PW was created." ::= { pwEntry 34 } pwUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the total time this PW operStatus has been Up(1)." ::= { pwEntry 35 } pwLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time the PW entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { pwEntry 36 } pwAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in a test mode } MAX-ACCESS read-create STATUS current DESCRIPTION "The desired operational status of this PW." ::= { pwEntry 37 } pwOperStatus OBJECT-TYPE SYNTAX PwOperStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the operational status of the PW, it does not reflect the status of the CE bound interface. It is set to down only if pwNotForwarding, psnFacingPwRxFault, or psnFacingPwTxFault indications are set in pwLocalStatus or pwRemoteStatus. It indicates 'lowerLayerDown' if the only reason for not being in the 'up' state is either outer tunnel or physical layer down of the network side is in the down state. All other states are declared based on the description in the textual convention. " ::= { pwEntry 38 } pwLocalStatus OBJECT-TYPE SYNTAX PwStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of the PW in the local node. The various indications in this object should be available independent of the ability of the local node to advertise them or the remote node to accept these status indications through the control protocol. " ::= { pwEntry 39 } pwRemoteStatusCapable OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), notYetKnown (2), remoteCapable (3), remoteNotCapable (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the remote node capability to advertise the PW status notification. notAppicable should be reported for manually set PW, or if the local node is not capable of sending the status notification object. notYetKnown should be reported if the signaling protocol has not yet finished the process of capability determination. remoteCapable and remoteNotcapable should be reported based on the initial signaling exchange that has determined the remote node capability. " ::= { pwEntry 40 } pwRemoteStatus OBJECT-TYPE SYNTAX PwStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the status of the PW as was advertised by the remote. If the remote is not capable of advertising the status object, or the local node is not able to accept the status object through signaling, then the applicable bit is 'pwNotForwarding' which is set if the remote has sent label release or label withdraw for this PW. " ::= { pwEntry 41 } pwTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds, including partial seconds, that have elapsed since the beginning of the current interval measurement period." ::= { pwEntry 42 } pwValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "The number of previous 15-minute intervals for which data was collected." ::= { pwEntry 43 } pwRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying, and deleting this row. None of the read-create objects in the conceptual rows may be changed when this object is in the active(1) state." ::= { pwEntry 44 } pwStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { pwEntry 45 } -- End of PW Virtual Connection Table -- PW Performance Table. pwPerfCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW performance information for the current interval." ::= { pwObjects 3 } pwPerfCurrentEntry OBJECT-TYPE SYNTAX PwPerfCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW." INDEX { pwIndex } ::= { pwPerfCurrentTable 1 } PwPerfCurrentEntry ::= SEQUENCE { pwPerfCurrentInHCPackets HCPerfCurrentCount, pwPerfCurrentInHCBytes HCPerfCurrentCount, pwPerfCurrentOutHCPackets HCPerfCurrentCount, pwPerfCurrentOutHCBytes HCPerfCurrentCount, pwPerfCurrentInPackets PerfCurrentCount, pwPerfCurrentInBytes PerfCurrentCount, pwPerfCurrentOutPackets PerfCurrentCount, pwPerfCurrentOutBytes PerfCurrentCount } pwPerfCurrentInHCPackets OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 1 } pwPerfCurrentInHCBytes OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 2 } pwPerfCurrentOutHCPackets OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 3 } pwPerfCurrentOutHCBytes OBJECT-TYPE SYNTAX HCPerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 4 } pwPerfCurrentInPackets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 32 bit version of pwPerfCurrentInHCPackets, if pwPerfCurrentInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 5 } pwPerfCurrentInBytes OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentInHCBytes, if pwPerfCurrentInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 6 } pwPerfCurrentOutPackets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCPackets, if pwPerfCurrentOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 7 } pwPerfCurrentOutBytes OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCBytes, if pwPerfCurrentOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfCurrentEntry 8 } -- End of PW Perf current Table -- PW Performance Interval Table. pwPerfIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW performance information for each interval." ::= { pwObjects 4 } pwPerfIntervalEntry OBJECT-TYPE SYNTAX PwPerfIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW." INDEX { pwIndex, pwPerfIntervalNumber } ::= { pwPerfIntervalTable 1 } PwPerfIntervalEntry ::= SEQUENCE { pwPerfIntervalNumber Integer32, pwPerfIntervalValidData TruthValue, pwPerfIntervalTimeElapsed HCPerfTimeElapsed, pwPerfIntervalInHCPackets HCPerfIntervalCount, pwPerfIntervalInHCBytes HCPerfIntervalCount, pwPerfIntervalOutHCPackets HCPerfIntervalCount, pwPerfIntervalOutHCBytes HCPerfIntervalCount, pwPerfIntervalInPackets PerfIntervalCount, pwPerfIntervalInBytes PerfIntervalCount, pwPerfIntervalOutPackets PerfIntervalCount, pwPerfIntervalOutBytes PerfIntervalCount } pwPerfIntervalNumber OBJECT-TYPE SYNTAX Integer32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 to 32. The maximum range of N is 1 through 96. " REFERENCE "Tesink, K. 'Definitions of Managed Objects for the SONET/SDH Interface Type', RFC 2558" ::= { pwPerfIntervalEntry 1 } pwPerfIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwPerfIntervalEntry 2 } pwPerfIntervalTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed MAX-ACCESS read-only STATUS current DESCRIPTION "The duration of this interval in seconds." ::= { pwPerfIntervalEntry 3 } pwPerfIntervalInHCPackets OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInPackets, if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 4 } pwPerfIntervalInHCBytes OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInBytes, if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 5 } pwPerfIntervalOutHCPackets OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutPackets, if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 6 } pwPerfIntervalOutHCBytes OBJECT-TYPE SYNTAX HCPerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of bytes forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutBytes, if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 7 } pwPerfIntervalInPackets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of packets received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalInHCPackets if pwPerfIntervalInHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 8 } pwPerfIntervalInBytes OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of bytes received by this PW during the interval. It MUST be equal to the least significant 32 bits of if pwPerfIntervalInHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 9 } pwPerfIntervalOutPackets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of packets sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCPackets if pwPerfIntervalOutHCPackets is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 10 } pwPerfIntervalOutBytes OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "This value represents the number of bytes sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCBytes if pwPerfIntervalOutHCBytes is supported according to the rules spelled out in RFC2863." ::= { pwPerfIntervalEntry 11 } -- End of PW Performance Interval Table -- PW Performance 1 Day Interval Table. pwPerf1DayIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-PW Performance information for the current day measurment and the previous days interval." ::= { pwObjects 5 } pwPerf1DayIntervalEntry OBJECT-TYPE SYNTAX PwPerf1DayIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW." INDEX { pwIndex, pwPerf1DayIntervalNumber } ::= { pwPerf1DayIntervalTable 1 } PwPerf1DayIntervalEntry ::= SEQUENCE { pwPerf1DayIntervalNumber Unsigned32, pwPerf1DayIntervalValidData TruthValue, pwPerf1DayIntervalMoniSecs HCPerfTimeElapsed, pwPerf1DayIntervalInHCPackets Counter64, pwPerf1DayIntervalInHCBytes Counter64, pwPerf1DayIntervalOutHCPackets Counter64, pwPerf1DayIntervalOutHCBytes Counter64 } pwPerf1DayIntervalNumber OBJECT-TYPE SYNTAX Unsigned32(1..31) MAX-ACCESS not-accessible STATUS current DESCRIPTION "History Data Interval number. Interval 1 is the current day measurement period, interval 2 is the most recent previous day, and interval 30 is 31 days ago. Intervals 3..31 are optional." ::= { pwPerf1DayIntervalEntry 1 } pwPerf1DayIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { pwPerf1DayIntervalEntry 2 } pwPerf1DayIntervalMoniSecs OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason or agaent clock adjustments." ::= { pwPerf1DayIntervalEntry 3 } pwPerf1DayIntervalInHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of packets received by the PW (from the PSN)." ::= { pwPerf1DayIntervalEntry 4 } pwPerf1DayIntervalInHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of bytes received by the PW (from the PSN)." ::= { pwPerf1DayIntervalEntry 5 } pwPerf1DayIntervalOutHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of packets forwarded by the PW (to the PSN)." ::= { pwPerf1DayIntervalEntry 6 } pwPerf1DayIntervalOutHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for the total number of bytes forwarded by the PW (to the PSN)." ::= { pwPerf1DayIntervalEntry 7 } -- End of PW Perf 1 Day Interval Table -- Error counter scalar pwPerfTotalErrorPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter for number of error at the PW processing level, for example packets received with unknown PW label." ::= { pwObjects 6 } -- Reverse mapping tables -- The PW ID mapping table pwIndexMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table enables the reverse mapping the unique PWid parameters [peer IP, PW type and PW ID] and the pwIndex. The table is not applicable for PW created manually or by using the generalized FEC." ::= { pwObjects 7 } pwIndexMappingEntry OBJECT-TYPE SYNTAX PwIndexMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table MUST be created by the agent for every PW created by the pwTable for which pwOwner equals pwIdFecSignaling. Implementors need to be aware that if the value of the pwIndexMappingPeerAddr (an OID) or pwIndexMappingPwID (an OID) (or both combined) has more than 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3." INDEX { pwIndexMappingPwType, pwIndexMappingPwID, pwIndexMappingPeerAddrType, pwIndexMappingPeerAddr } ::= { pwIndexMappingTable 1 } PwIndexMappingEntry ::= SEQUENCE { pwIndexMappingPwType IANAPwTypeTC, pwIndexMappingPwID PwIDType, pwIndexMappingPeerAddrType InetAddressType, pwIndexMappingPeerAddr InetAddress, pwIndexMappingPwIndex PwIndexType } pwIndexMappingPwType OBJECT-TYPE SYNTAX IANAPwTypeTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW type (indicates the service) of this PW." ::= { pwIndexMappingEntry 1 } pwIndexMappingPwID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW ID of this PW. Zero if the PW is configured manually." ::= { pwIndexMappingEntry 2 } pwIndexMappingPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwIndexMappingEntry 3 } pwIndexMappingPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwIndexMappingEntry 4 } pwIndexMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represents the PW in the pwTable." ::= { pwIndexMappingEntry 5 } -- End of the PW ID mapping table -- The peer mapping table pwPeerMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PwPeerMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides reverse mapping of the existing PW based on PW type and PW ID ordering. This table is typically useful for EMS ordered query of existing PWs." ::= { pwObjects 8 } pwPeerMappingEntry OBJECT-TYPE SYNTAX PwPeerMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the agent for every PW configured in pwTable. Implementors need to be aware that if the value of the pwPeerMappingPeerAddr (an OID) or pwPeerMappingPwID (an OID) (or both combined) has more than 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3." INDEX { pwPeerMappingPeerAddrType, pwPeerMappingPeerAddr, pwPeerMappingPwType, pwPeerMappingPwID } ::= { pwPeerMappingTable 1 } PwPeerMappingEntry ::= SEQUENCE { pwPeerMappingPeerAddrType InetAddressType, pwPeerMappingPeerAddr InetAddress, pwPeerMappingPwType IANAPwTypeTC, pwPeerMappingPwID PwIDType, pwPeerMappingPwIndex PwIndexType } pwPeerMappingPeerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwPeerMappingEntry 1 } pwPeerMappingPeerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address type of the peer node." ::= { pwPeerMappingEntry 2 } pwPeerMappingPwType OBJECT-TYPE SYNTAX IANAPwTypeTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW type (indicates the service) of this PW." ::= { pwPeerMappingEntry 3 } pwPeerMappingPwID OBJECT-TYPE SYNTAX PwIDType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PW ID of this PW. Zero if the PW is configured manually." ::= { pwPeerMappingEntry 4 } pwPeerMappingPwIndex OBJECT-TYPE SYNTAX PwIndexType MAX-ACCESS read-only STATUS current DESCRIPTION "The value that represents the PW in the pwTable." ::= { pwPeerMappingEntry 5 } -- End of the peer mapping table -- End of reverse mapping tables pwUpDownNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwUp and pwDown notifications; otherwise these notifications are not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { false } ::= { pwObjects 9 } pwDeletedNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is set to true(1), then it enables the emission of pwDeleted notification; otherwise this notification is not emitted." REFERENCE "See also [RFC3413] for explanation that notifications are under the ultimate control of the MIB module in this document." DEFVAL { false } ::= { pwObjects 10 } pwNotifRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object defines the maximum number of PW notifications that can be emitted from the device per second." ::= { pwObjects 11 } -- Notifications - PW pwDown NOTIFICATION-TYPE OBJECTS { pwOperStatus, --start of range pwOperStatus --end of range } STATUS current DESCRIPTION "This notification is generated when the pwOperStatus object for one or more contiguous entries in pwTable are about to enter the down(2) state from some other state. The included values of pwOperStatus MUST all be set equal to this down(2) state. The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the down(2) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be identical." ::= { pwNotifications 1 } pwUp NOTIFICATION-TYPE OBJECTS { pwOperStatus, --start of range pwOperStatus --end of range } STATUS current DESCRIPTION "This notification is generated when the pwOperStatus object for one or more contiguous entries in pwTable are about to enter the up(1) state from some other state. The included values of pwOperStatus MUST both be set equal to this new state (i.e: up(1)). The two instances of pwOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two pwOperStatus objects MUST be the identical." ::= { pwNotifications 2 } pwDeleted NOTIFICATION-TYPE OBJECTS { pwType, pwID, pwPeerAddrType, pwPeerAddr } STATUS current DESCRIPTION "This notification is generated when the PW has been deleted, i.e. when the pwRowStatus has been set to destroy(6), the PW has been deleted by a non-MIB application or due to auto-discovery process. " ::= { pwNotifications 3 } -- End of notifications. -- Conformance information pwGroups OBJECT IDENTIFIER ::= { pwConformance 1 } pwCompliances OBJECT IDENTIFIER ::= { pwConformance 2 } -- Compliance requirement for fully compliant implementations. pwModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide full support for PW MIB Module. Such devices can then be monitored and also be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwBasicGroup, pwPerformanceGeneralGroup } GROUP pwNotificationGroup DESCRIPTION "This group is only mandatory for implementations which can efficiently implement the notifications contained in this group. " GROUP pwPwIdGroup DESCRIPTION "This group is only mandatory for implementations that support the PW ID FEC. " GROUP pwGeneralizedFecGroup DESCRIPTION "This group is only mandatory for implementations that support the generalized PW FEC. " GROUP pwFcsGroup DESCRIPTION "This group is only mandatory for implementations that support FCS retention." GROUP pwFragGroup DESCRIPTION "This group is only mandatory for implementations that support PW fragmentation. " GROUP pwPwStatusGroup DESCRIPTION "This group is only mandatory for implementations that support PW status notification. " GROUP pwGetNextGroup DESCRIPTION "This group is only mandatory for implementations where the pwIndex may be any arbitrary value and the EMS would require retrieval of the next free index." GROUP pwPriorityGroup DESCRIPTION "This group is only mandatory for implementations that support the controlling the PW setup and holding priority." GROUP pwAttachmentGroup DESCRIPTION "This group is only mandatory for implementations that support attachment of two PWs (PW stitching)." GROUP pwPeformance1DayIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 1 day intervals." GROUP pwPerformanceIntervalGeneralGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minute intervals." GROUP pwPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minute intervals." GROUP pwHCPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the interval performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwMappingTablesGroup DESCRIPTION "This group is only mandatory for implementations that support reverse mapping of PW indexes to the pwIndex and the peer mapping table." GROUP pwSignalingGroup DESCRIPTION "This group is only mandatory for implementations that support the PW signaling." GROUP pwNotificationControlGroup DESCRIPTION "This group is only mandatory for implementations that support the PW notifications." OBJECT pwAdminStatus SYNTAX INTEGER { up(1), down(2) } DESCRIPTION "The support of the value testing(3) is not required." OBJECT pwOperStatus SYNTAX INTEGER { up(1), down(2), notPresent(5), lowerLayerDown(6) } DESCRIPTION "The support of the values testing(3) and dormant(4) is not required." OBJECT pwRowStatus SYNTAX RowStatus { active(1), notInService(2), notReady(3) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for createAndWait is not required. Support of notReady is not required for implementations that do not support signaling, or if it is guaranteed that the conceptual row has all the required information to create the PW when the row has been created by the agent or written by the operator." OBJECT pwPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1) } MIN-ACCESS read-only DESCRIPTION "Only unknown(0) and ipv4(1) is required. Implementation that support only IPv4 MAY support read-only access." OBJECT pwPeerAddr SYNTAX InetAddress (SIZE(0|4)) DESCRIPTION "An implementation is only required to support 0, 4 address sizes." OBJECT pwStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwNotifRate MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pwCompliances 1 } -- Compliance requirement for read-only compliant implementations. pwModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that provide read- only support for PW MIB Module. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { pwBasicGroup } GROUP pwNotificationGroup DESCRIPTION "This group is only mandatory for implementations which can efficiently implement the notifications contained in this group." GROUP pwPwIdGroup DESCRIPTION "This group is only mandatory for implementations that support the PW ID FEC. " GROUP pwGeneralizedFecGroup DESCRIPTION "This group is only mandatory for implementations that support the generalized PW FEC. " GROUP pwFcsGroup DESCRIPTION "This group is only mandatory for implementations that support FCS retention." GROUP pwFragGroup DESCRIPTION "This group is only mandatory for implementations that support PW fragmentation. " GROUP pwPwStatusGroup DESCRIPTION "This group is only mandatory for implementations that support PW status notification. " GROUP pwGetNextGroup DESCRIPTION "This group is only mandatory for implementations where the pwIndex may be any arbitary value and the EMS would require retrieval of the next free index." GROUP pwPriorityGroup DESCRIPTION "This group is only mandatory for implementations that support the controling the PW setup and holding priority." GROUP pwAttachmentGroup DESCRIPTION "This group is only mandatory for implementations that support attachment of two PWs (PW stitching)." GROUP pwPeformance1DayIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 1 Day intervals." GROUP pwPerformanceIntervalGeneralGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minute intervals." GROUP pwPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations that support PW performance gathering in 15 minute intervals." GROUP pwHCPeformanceIntervalGroup DESCRIPTION "This group is only mandatory for implementations where at least one of the interval performance counters wraps around too quickly based on the criteria specified in RFC 2863 for high-capacity counters." GROUP pwMappingTablesGroup DESCRIPTION "This group is only mandatory for implementations that support reverse mapping of PW indexes to the pwIndex and the peer mapping table." GROUP pwSignalingGroup DESCRIPTION "This group is only mandatory for implementations that support the PW signaling." GROUP pwNotificationControlGroup DESCRIPTION "This group is only mandatory for implementations that support the PW notifications." OBJECT pwType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwOwner MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPsnType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwSetUpPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwHoldingPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPeerAddrType SYNTAX InetAddressType { unknown(0), ipv4(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. Only unknown(0) and ipv4(1) is required." OBJECT pwPeerAddr SYNTAX InetAddress (SIZE(0|4)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is only required to support 0, 4 address sizes." OBJECT pwAttachedPwIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalGroupID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwGroupAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwPeerAttachmentID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwCwPreference MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalIfMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalIfString MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwLocalCapabAdvert MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwFragmentCfgSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwFcsRetentioncfg MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwOutboundLabel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwInboundLabel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwDescr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwAdminStatus SYNTAX INTEGER { up(1), down(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. The support of value testing(3) is not required." OBJECT pwOperStatus SYNTAX INTEGER { up(1), down(2), notPresent(5), lowerLayerDown(6) } DESCRIPTION "The support of the values testing(3) and dormant(4) is not required." OBJECT pwRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwUpDownNotifEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwDeletedNotifEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT pwNotifRate MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pwCompliances 2 } -- Units of conformance. pwBasicGroup OBJECT-GROUP OBJECTS { pwType, pwOwner, pwPsnType, pwIfIndex, pwCwPreference, pwLocalIfMtu, pwOutboundLabel, pwInboundLabel, pwName, pwDescr, pwCreateTime, pwUpTime, pwLastChange, pwAdminStatus, pwOperStatus, pwLocalStatus, pwRowStatus, pwStorageType } STATUS current DESCRIPTION "Collection of objects that are required in all implementations that support the PW MIB module." ::= { pwGroups 1 } pwPwIdGroup OBJECT-GROUP OBJECTS { pwID } STATUS current DESCRIPTION "Collection of objects required for PW ID configuration and signaling." ::= { pwGroups 2 } pwGeneralizedFecGroup OBJECT-GROUP OBJECTS { pwGroupAttachmentID, pwLocalAttachmentID, pwPeerAttachmentID } STATUS current DESCRIPTION "Collection of objects required for generalized FEC configuration and signaling." ::= { pwGroups 3 } pwFcsGroup OBJECT-GROUP OBJECTS { pwFcsRetentioncfg, pwFcsRetentionStatus } STATUS current DESCRIPTION "Collection of objects required for FCS retention configuration and signaling." ::= { pwGroups 4 } pwFragGroup OBJECT-GROUP OBJECTS { pwFragmentCfgSize, pwRmtFragCapability } STATUS current DESCRIPTION "Collection of objects required for fragmentation configuration and signaling." ::= { pwGroups 5 } pwPwStatusGroup OBJECT-GROUP OBJECTS { pwRemoteCapabilities, pwRemoteStatusCapable, pwRemoteStatus } STATUS current DESCRIPTION "Collection of objects required for PW status configuration and signaling." ::= { pwGroups 6 } pwGetNextGroup OBJECT-GROUP OBJECTS { pwIndexNext } STATUS current DESCRIPTION "Collection of objects for getting the next available index." ::= { pwGroups 7 } pwPriorityGroup OBJECT-GROUP OBJECTS { pwSetUpPriority, pwHoldingPriority } STATUS current DESCRIPTION "Collection of objects for controlling the PW setup and holding priority." ::= { pwGroups 8 } pwAttachmentGroup OBJECT-GROUP OBJECTS { pwAttachedPwIndex } STATUS current DESCRIPTION "Collection of objects for PW configuration as ifIndex" ::= { pwGroups 9 } pwPerformanceGeneralGroup OBJECT-GROUP OBJECTS { pwPerfTotalErrorPackets } STATUS current DESCRIPTION "Collection of general objects needed for managing the total running performance parameters." ::= { pwGroups 10 } pwPeformance1DayIntervalGroup OBJECT-GROUP OBJECTS { pwPerf1DayIntervalValidData, pwPerf1DayIntervalMoniSecs, pwPerf1DayIntervalInHCPackets, pwPerf1DayIntervalInHCBytes, pwPerf1DayIntervalOutHCPackets, pwPerf1DayIntervalOutHCBytes } STATUS current DESCRIPTION "Collection of objects needed for PW running 1 day interval performance collection." ::= { pwGroups 11 } pwPerformanceIntervalGeneralGroup OBJECT-GROUP OBJECTS { pwTimeElapsed, pwValidIntervals, pwPerfIntervalValidData, pwPerfIntervalTimeElapsed } STATUS current DESCRIPTION "Collection of general objects needed for managing the interval performance parameters." ::= { pwGroups 12 } pwPeformanceIntervalGroup OBJECT-GROUP OBJECTS { pwPerfCurrentInPackets, pwPerfCurrentInBytes, pwPerfCurrentOutPackets, pwPerfCurrentOutBytes, pwPerfIntervalInPackets, pwPerfIntervalInBytes, pwPerfIntervalOutPackets, pwPerfIntervalOutBytes } STATUS current DESCRIPTION "Collection of 32 bits objects needed for PW performance collection in 15 minutes intervals." ::= { pwGroups 13 } pwHCPeformanceIntervalGroup OBJECT-GROUP OBJECTS { pwPerfCurrentInHCPackets, pwPerfCurrentInHCBytes, pwPerfCurrentOutHCPackets, pwPerfCurrentOutHCBytes, pwPerfIntervalInHCPackets, pwPerfIntervalInHCBytes, pwPerfIntervalOutHCPackets, pwPerfIntervalOutHCBytes } STATUS current DESCRIPTION "Collection of HC objects needed for PW performance collection in 15 minutes intervals." ::= { pwGroups 14 } pwMappingTablesGroup OBJECT-GROUP OBJECTS { pwIndexMappingPwIndex, pwPeerMappingPwIndex } STATUS current DESCRIPTION "Collection of objects contained in the reverse mapping tables." ::= { pwGroups 15 } pwNotificationControlGroup OBJECT-GROUP OBJECTS { pwUpDownNotifEnable, pwDeletedNotifEnable, pwNotifRate } STATUS current DESCRIPTION "Collection of objects for controlling the PW notifications." ::= { pwGroups 16 } pwNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { pwUp, pwDown, pwDeleted } STATUS current DESCRIPTION "Collection PW notifications objects." ::= { pwGroups 17 } pwSignalingGroup OBJECT-GROUP OBJECTS { pwPeerAddrType, pwPeerAddr, pwLocalGroupID, pwLocalIfString, pwLocalCapabAdvert, pwRemoteGroupID, pwCwStatus, pwRemoteIfMtu, pwRemoteIfString } STATUS current DESCRIPTION "Collection of objects for use in implementations that support the PW signaling." ::= { pwGroups 18 } END -- -- Copyright (C) The Internet Society (2006). -- -- This document is subject to the rights, licenses and restrictions -- contained in BCP 78, and except as set forth therein, the authors -- retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- -- -- Intellectual Property -- -- The IETF takes no position regarding the validity or scope of any -- Intellectual Property Rights or other rights that might be claimed to -- pertain to the implementation or use of the technology described in -- this document or the extent to which any license under such rights -- might or might not be available; nor does it represent that it has -- made any independent effort to identify any such rights. Information -- on the procedures with respect to rights in RFC documents can be -- found in BCP 78 and BCP 79. -- -- Copies of IPR disclosures made to the IETF Secretariat and any -- assurances of licenses to be made available, or the result of an -- attempt made to obtain a general license or permission for the use of -- such proprietary rights by implementers or users of this -- specification can be obtained from the IETF on-line IPR repository at -- http://www.ietf.org/ipr. -- -- The IETF invites any interested party to bring to its attention any -- copyrights, patents or patent applications, or other proprietary -- rights that may cover technology that may be required to implement -- this standard. Please address the information to the IETF at -- ietf-ipr@ietf.org. -- -- -- Acknowledgment -- -- Funding for the RFC Editor function is provided by the IETF -- Administrative Support Activity (IASA).