-- extracted from draft-kzm-imss-fc-rscn-mib-01.txt -- at Fri Dec 9 06:40:19 2005 T11-FC-RSCN-MIB DEFINITIONS ::= BEGIN -- The Fibre Channel RSCN Register MIB -- -- for the monitoring of registrations by Nx_Ports to receive -- Registered State Change Notifications (RSCNs). -- IMPORTS MODULE-IDENTITY,OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, mib-2 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC -- [RFC2579] fcmInstanceIndex, fcmSwitchIndex, FcNameIdOrZero, FcAddressIdOrZero FROM FC-MGMT-MIB -- [FC-MGMT] T11FabricIndex FROM T11-TC-MIB; -- [FC-FAM-MIB] t11FcRscnMIB MODULE-IDENTITY LAST-UPDATED "200512060000Z" ORGANIZATION "T11 " CONTACT-INFO " Claudio DeSanti Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 408 853-9172 EMail: cds@cisco.com Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA 95134 Phone: +1 408-526-5260 Email: kzm@cisco.com" DESCRIPTION "The MIB module for the management of registrations by Nx_Ports to receive RSCNs (Registered State Change Notifications) on a Fibre Channel network, as defined in FC-FS, and for the monitoring of RSCNs sent/received or rejected in a Fibre Channel network. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices." -- RFC Editor: replace yyyy with actual RFC number & remove this note REVISION "200512060000Z" DESCRIPTION "Initial version of this MIB module, published as RFCyyyy." -- RFC-Editor, replace yyyy with actual RFC number & remove this note ::= { mib-2 nnn } -- to be assigned by IANA -- RFC Editor: replace XXX with IANA-assigned number & remove this note t11FcRscnNotifications OBJECT IDENTIFIER ::= { t11FcRscnMIB 0 } t11FcRscnObjects OBJECT IDENTIFIER ::= { t11FcRscnMIB 1 } t11FcRscnConformance OBJECT IDENTIFIER ::= { t11FcRscnMIB 2 } t11FcRscnRegistrations OBJECT IDENTIFIER ::= { t11FcRscnObjects 1 } t11FcRscnStats OBJECT IDENTIFIER ::= { t11FcRscnObjects 2 } t11FcRscnInformation OBJECT IDENTIFIER ::= { t11FcRscnObjects 3 } T11FcLsRejectReasonCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The LS_RJT or SW_RJT reject reason code and reason code explanation for rejecting a request. The value is formatted as specified in FC-FS or FC-SW-4, respectively -- to summarize: bits 31-24 (most significant) - reserved bits 23-16 - standard reason code bits 15-8 - reason code explanation bits 7-0 (least significant) - vendor-specific code The vendor-specific code indicates the reason when the standard reason code has the value x'FF'." REFERENCE "-- ANSI INCITS xxx-200n, Fibre Channel - Framing and Signaling (FC-FS), Rev 1.90, section 12.3.3.4.2, April 2003; and -- ANSI INCITS xxx-200n, Fibre Channel - Switch Fabric - 4 (FC-SW-4), T11/Project 1674-D/Rev 7.1, section 6.1.3, October 2004." SYNTAX OCTET STRING (SIZE (4)) -- State Change Registration Table t11FcRscnRegTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcRscnRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Nx_Ports that have registered to receive RSCNs on all fabrics configured on one or more Fibre Channel switches." ::= { t11FcRscnRegistrations 1 } t11FcRscnRegEntry OBJECT-TYPE SYNTAX T11FcRscnRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about one Nx_Port which has registered with a particular switch (identified by values of fcmInstanceIndex and fcmSwitchIndex) for a particular Fabric (identified by a t11FcRscnFabricIndex value)." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FcRscnFabricIndex, t11FcRscnRegFcId } ::= { t11FcRscnRegTable 1 } T11FcRscnRegEntry ::= SEQUENCE { t11FcRscnFabricIndex T11FabricIndex, t11FcRscnRegFcId FcAddressIdOrZero, t11FcRscnRegType BITS } t11FcRscnFabricIndex OBJECT-TYPE SYNTAX T11FabricIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value which uniquely identifies a particular Fabric. In a Fabric conformant to FC-SW-4, multiple Virtual Fabrics can operate within one (or more) physical infrastructures. In such a case, this index value is used to uniquely identify a particular Fabric within a physical infrastructure. In a Fabric which has (can have) only a single Fabric operating within the physical infrastructure, the value of this Fabric Index will always be 1." REFERENCE "ANSI INCITS xxx-200n, Fibre Channel - Switch Fabric - 4 (FC-SW-4), T11/Project 1674-D/Rev 7.1, October 2004." ::= { t11FcRscnRegEntry 1 } t11FcRscnRegFcId OBJECT-TYPE SYNTAX FcAddressIdOrZero (SIZE (3)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Fibre Channel Address Identifier (FC_ID) of the subscribing Nx_Port." ::= { t11FcRscnRegEntry 2 } t11FcRscnRegType OBJECT-TYPE SYNTAX BITS { fromFabricController(0), fromNxPort(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of registration desired by the subscriber, one bit per type: 'fromFabricController' -- RSCNs generated for events detected by the Fabric Controller. 'fromNxPorts' -- RSCNs generated for events detected by the affected Nx_Port." REFERENCE "ANSI INCITS xxx-200n, Fibre Channel - Framing and Signaling (FC-FS), Rev 1.90, section 12.3.2.23, April 2003." ::= { t11FcRscnRegEntry 3 } -- Statistics t11FcRscnStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcRscnStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RSCN-related statistics on all fabrics configured on one or more Fibre Channel switches." ::= { t11FcRscnStats 1 } t11FcRscnStatsEntry OBJECT-TYPE SYNTAX T11FcRscnStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing statistics for a particular Fabric (identified by a t11FcRscnFabricIndex value) on a particular switch (identified by values of fcmInstanceIndex and fcmSwitchIndex)." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FcRscnFabricIndex } ::= { t11FcRscnStatsTable 1 } T11FcRscnStatsEntry ::= SEQUENCE { t11FcRscnRxScrs Counter32, t11FcRscnRxRscns Counter32, t11FcRscnTxRscns Counter32, t11FcRscnRxSwRscns Counter32, t11FcRscnTxSwRscns Counter32, t11FcRscnScrRejects Counter32, t11FcRscnRscnRejects Counter32, t11FcRscnSwRscnRejects Counter32 } t11FcRscnRxScrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCRs received from Nx_Ports by this switch on this fabric." ::= { t11FcRscnStatsEntry 1 } t11FcRscnRxRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RSCNs received from Nx_Ports by this switch on this fabric." ::= { t11FcRscnStatsEntry 2 } t11FcRscnTxRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RSCNs transmitted to Nx_Ports by this switch on this fabric." ::= { t11FcRscnStatsEntry 3 } t11FcRscnRxSwRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Inter-Switch RSCN payloads (SW_RSCN in an SW_ILS) received by this switch from other switches on this fabric." ::= { t11FcRscnStatsEntry 4 } t11FcRscnTxSwRscns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Inter-Switch RSCN payloads (SW_RSCN in an SW_ILS) transmitted by this switch from other switches on this fabric." ::= { t11FcRscnStatsEntry 5 } t11FcRscnScrRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SCRs rejected by this switch on this fabric." ::= { t11FcRscnStatsEntry 6 } t11FcRscnRscnRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RSCN requests rejected by this switch on this fabric." ::= { t11FcRscnStatsEntry 7 } t11FcRscnSwRscnRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SW_RSCN requests rejected by this switch on this fabric." ::= { t11FcRscnStatsEntry 8 } -- -- Notification Control Table -- t11FcRscnNotifyControlTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcRscnNotifyControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of control information for notifications generated due to the rejection of SCR and RSCN requests." ::= { t11FcRscnInformation 1 } t11FcRscnNotifyControlEntry OBJECT-TYPE SYNTAX T11FcRscnNotifyControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains notification control information concerning the rejection of RSCN/SCRs for a particular fabric (identified by the value of t11FcRscnFabricIndex) by a particular switch (identified by values of fcmInstanceIndex and fcmSwitchIndex)." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FcRscnFabricIndex } ::= { t11FcRscnNotifyControlTable 1 } T11FcRscnNotifyControlEntry ::= SEQUENCE { t11FcRscnIlsRejectNotifyEnable TruthValue, t11FcRscnElsRejectNotifyEnable TruthValue, t11FcRscnRejectedRequestString OCTET STRING, t11FcRscnRejectedRequestSource FcNameIdOrZero, t11FcRscnRejectedReasonCode T11FcLsRejectReasonCode } t11FcRscnIlsRejectNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if a t11FcRscnIlsRejectReqNotify notification should be generated when this switch rejects a SW_ILS with a SW_RSCN payload on this fabric." DEFVAL { false } ::= { t11FcRscnNotifyControlEntry 1 } t11FcRscnElsRejectNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies if a t11FcRscnElsRejectReqNotify notification should be generated when this switch rejects a RSCN or SCR request on this fabric." DEFVAL { false } ::= { t11FcRscnNotifyControlEntry 2 } t11FcRscnRejectedRequestString OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The binary content of the RSCN or SCR which was most recently rejected by this switch on this fabric. The value is formatted as an octet string (in network byte order) containing the payload of the RSCN or SCR request, as described in Table 100 or Table 105 (of FC-FS) respectively. This object contains the zero-length string if and when the RSCN/SCR payload is unavailable. When the length of this object is 255 octets, it contains the first 255 octets of the payload (in network-byte order)." ::= { t11FcRscnNotifyControlEntry 3 } t11FcRscnRejectedRequestSource OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The WWN which was the source of the RSCN or SCR which was most recently rejected by this switch on this fabric." ::= { t11FcRscnNotifyControlEntry 4 } t11FcRscnRejectedReasonCode OBJECT-TYPE SYNTAX T11FcLsRejectReasonCode MAX-ACCESS read-only STATUS current DESCRIPTION "The reason code and the reason code explanation of the most recent rejection by this switch of an RSCN or SCR on this fabric." REFERENCE "ANSI INCITS xxx-200n, Fibre Channel - Framing and Signaling (FC-FS), Rev 1.90, section 12.3.3.4.2, April 2003." ::= { t11FcRscnNotifyControlEntry 5 } -- Notifications t11FcRscnElsRejectReqNotify NOTIFICATION-TYPE OBJECTS { t11FcRscnRejectedRequestString, t11FcRscnRejectedRequestSource, t11FcRscnRejectedReasonCode } STATUS current DESCRIPTION "This notification is generated when a switch rejects a SCR or RSCN request. If the binary content of the rejected request is available, it is indicated by the value of t11FcRscnRejectedRequestString. The source of the rejected request is t11FcRscnRejectedRequestSource, and the reason for rejection is given by the value of t11FcRscnRejectedReasonCode." ::= { t11FcRscnNotifications 1 } t11FcRscnIlsRejectReqNotify NOTIFICATION-TYPE OBJECTS { t11FcRscnRejectedRequestString, t11FcRscnRejectedRequestSource, t11FcRscnRejectedReasonCode } STATUS current DESCRIPTION "This notification is generated when a switch rejects a SW_RSCN request. If the binary content of the rejected request is available, it is indicated by the value of t11FcRscnRejectedRequestString. The source of the rejected request is t11FcRscnRejectedRequestSource, and the reason for rejection is given by the value of t11FcRscnRejectedReasonCode." ::= { t11FcRscnNotifications 2 } -- Conformance t11FcRscnCompliances OBJECT IDENTIFIER ::= { t11FcRscnConformance 1 } t11FcRscnGroups OBJECT IDENTIFIER ::= { t11FcRscnConformance 2 } t11FcRscnCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement this MIB." MODULE MANDATORY-GROUPS { t11FcRscnRegistrationGroup, t11FcRscnNotifyControlGroup, t11FcRscnNotifyGroup } GROUP t11FcRscnStatsGroup DESCRIPTION "These counters, containing RSCN-related statistics, are mandatory only for those systems which count such events." OBJECT t11FcRscnIlsRejectNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcRscnElsRejectNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { t11FcRscnCompliances 1 } -- Units of conformance t11FcRscnRegistrationGroup OBJECT-GROUP OBJECTS { t11FcRscnRegType } STATUS current DESCRIPTION "A collection of objects for monitoring RSCN registrations." ::= { t11FcRscnGroups 1 } t11FcRscnStatsGroup OBJECT-GROUP OBJECTS { t11FcRscnRxScrs, t11FcRscnRxRscns, t11FcRscnTxRscns, t11FcRscnRxSwRscns, t11FcRscnTxSwRscns, t11FcRscnScrRejects, t11FcRscnRscnRejects, t11FcRscnSwRscnRejects } STATUS current DESCRIPTION "A collection of objects for collecting RSCN registration statistics." ::= { t11FcRscnGroups 2 } t11FcRscnNotifyControlGroup OBJECT-GROUP OBJECTS { t11FcRscnIlsRejectNotifyEnable, t11FcRscnElsRejectNotifyEnable, t11FcRscnRejectedRequestString, t11FcRscnRejectedRequestSource, t11FcRscnRejectedReasonCode } STATUS current DESCRIPTION "A collection of notification control and notification information objects." ::= { t11FcRscnGroups 3 } t11FcRscnNotifyGroup NOTIFICATION-GROUP NOTIFICATIONS { t11FcRscnIlsRejectReqNotify, t11FcRscnElsRejectReqNotify } STATUS current DESCRIPTION "A collection of notifications for monitoring ILS and ELS request rejection by the RSCN module." ::= { t11FcRscnGroups 4 } END -- -- Copyright (C) The Internet Society (2005). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- Disclaimer of validity -- -- The IETF takes no position regarding the validity or scope of any -- Intellectual Property Rights or other rights that might be claimed to -- pertain to the implementation or use of the technology described in -- this document or the extent to which any license under such rights -- might or might not be available; nor does it represent that it has -- made any independent effort to identify any such rights. Information -- on the procedures with respect to rights in RFC documents can be -- found in BCP 78 and BCP 79. -- -- Copies of IPR disclosures made to the IETF Secretariat and any -- assurances of licenses to be made available, or the result of an -- attempt made to obtain a general license or permission for the use of -- such proprietary rights by implementers or users of this -- specification can be obtained from the IETF on-line IPR repository at -- http://www.ietf.org/ipr. -- -- The IETF invites any interested party to bring to its attention any -- copyrights, patents or patent applications, or other proprietary -- rights that may cover technology that may be required to implement -- this standard. Please address the information to the IETF at -- ietf-ipr@ietf.org. -- -- Acknowledgment -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society.