-- extracted from draft-ietf-tsvwg-tcp-mib-extension-09.txt -- at Fri Mar 10 06:11:02 2006 TCP-ESTATS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, Counter32, Integer32, Unsigned32, Gauge32, OBJECT-TYPE, mib-2, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ZeroBasedCounter32 FROM RMON2-MIB -- [RFC2021] ZeroBasedCounter64 FROM HCNUM-TC -- [RFC2856] TEXTUAL-CONVENTION, DateAndTime, TruthValue, TimeStamp FROM SNMPv2-TC -- [RFC2579] tcpListenerEntry, tcpConnectionEntry FROM TCP-MIB; -- [RFC4022] tcpEStatsMIB MODULE-IDENTITY LAST-UPDATED "200603041322Z" -- Mar 4, 2006 ORGANIZATION "IETF TSV Working Group" CONTACT-INFO "Matt Mathis John Heffner Raghu Reddy Web100 Project Pittsburgh Supercomputing Center 4400 Fifth Ave Pittsburgh, PA 15213 Email: mathis@psc.edu, jheffner@psc.edu, rreddy@psc.edu Rajiv Raghunarayan Cisco Systems Inc. San Jose, CA 95134 Phone: 408 853 9612 Email: raraghun@cisco.com Jon Saperia JDS Consulting, Inc. 174 Chapman Street Watertown, MA 02472 Phone: 617-744-1079 Email: saperia@jdscons.com " DESCRIPTION "Documentation of TCP Extended Performance Instrumentation variables from the Web100 project. [Web100] Copyright (C) The Internet Society (2005). This version of this MIB module is a part of RFC xxx1; see the RFC itself for full legal notices." -- RFC Editor: replace xxx1 with actual RFC number & remove note REVISION "200603041322Z" -- Mar 4, 2006 DESCRIPTION "Initial version, published as RFC xxx1." -- RFC Editor assigns RFC xxx1 ::= { mib-2 xxx2 } -- RFC Editor: IANA assigns base OID xxx2 tcpEStatsNotifications OBJECT IDENTIFIER ::= { tcpEStatsMIB 0 } tcpEStatsMIBObjects OBJECT IDENTIFIER ::= { tcpEStatsMIB 1 } tcpEStatsConformance OBJECT IDENTIFIER ::= { tcpEStatsMIB 2 } tcpEStats OBJECT IDENTIFIER ::= { tcpEStatsMIBObjects 1 } tcpEStatsControl OBJECT IDENTIFIER ::= { tcpEStatsMIBObjects 2 } tcpEStatsScalar OBJECT IDENTIFIER ::= { tcpEStatsMIBObjects 3 } -- -- Textual Conventions -- TcpEStatsNegotiated ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates if some optional TCP feature was negotiated. Enabled(1) indicates that the feature was successfully negotiated on, which generally requires both host to agree to use the feature. selfDisabled(2) indicates that the local host refused the feature because it is not implemented, configured off or refused for some other reason, such as the lack of resources. peerDisabled(3) indicates that the local host was willing to negotiate the feature, but the remote host did not did not do so." SYNTAX INTEGER { enabled(1), selfDisabled(2), peerDisabled(3) } -- -- TCP Extended statistics scalars -- tcpEStatsListenerTableLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last creation or deletion of an entry in the tcpListenerTable. If the number of entries has been unchanged since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { tcpEStatsScalar 3 } -- ================================================================ -- -- The tcpEStatsControl Group -- -- The scalar objects in this group are used to control the -- activation and deactivation of the TCP Extended Statistics -- tables and notifications in this module. -- tcpEStatsControlPath OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the activation of the TCP Path Statistics table. A value 'true' indicates that the TCP Path Statistics table is active, while 'false' indicates that the table is inactive." DEFVAL { false } ::= { tcpEStatsControl 1 } tcpEStatsControlStack OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the activation of the TCP Stack Statistics table. A value 'true' indicates that the TCP Path Statistics table is active, while 'false' indicates that the table is inactive." DEFVAL { false } ::= { tcpEStatsControl 2 } tcpEStatsControlApp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the activation of the TCP Application Statistics table. A value 'true' indicates that the TCP Path Statistics table is active, while 'false' indicates that the table is inactive." DEFVAL { false } ::= { tcpEStatsControl 3 } tcpEStatsControlTune OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the activation of the TCP Tuning table. A value 'true' indicates that the TCP Path Statistics table is active, while 'false' indicates that the table is inactive." DEFVAL { false } ::= { tcpEStatsControl 4 } tcpEStatsControlNotify OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Controls the generation of all notifications defined in this MIB. A value 'true' indicates that the TCP Path Statistics table is active, while 'false' indicates that the table is inactive." DEFVAL { false } ::= { tcpEStatsControl 5 } tcpEStatsConnTableLatency OBJECT-TYPE SYNTAX Integer32 (0..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of seconds that the entity will retain entries in the TCP connection tables, after the connection first enters the closed state. The entity SHOULD provide a configuration option to enable customization of this value. A value of 0 results in entries being removed from the tables as soon as the connection enters the closed state. The value of this object pertains to the following tables: tcpEStatsConnectIdTable tcpEStatsPerfTable tcpEStatsPathTable tcpEStatsStackTable tcpEStatsAppTable tcpEStatsTuneTable" DEFVAL { 0 } ::= { tcpEStatsControl 6 } -- ================================================================ -- -- Listener Table -- tcpEStatsListenerTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsListenerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about TCP Listeners, in addition to the information maintained by the tcpListenerTable RFC4022." ::= { tcpEStats 1 } tcpEStatsListenerEntry OBJECT-TYPE SYNTAX TcpEStatsListenerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in the table contains information about a specific TCP Listener." AUGMENTS { tcpListenerEntry } ::= { tcpEStatsListenerTable 1 } TcpEStatsListenerEntry ::= SEQUENCE { tcpEStatsListenerStartTime TimeStamp, tcpEStatsListenerSynRcvd ZeroBasedCounter32, tcpEStatsListenerInitial ZeroBasedCounter32, tcpEStatsListenerEstablished ZeroBasedCounter32, tcpEStatsListenerAccepted ZeroBasedCounter32, tcpEStatsListenerExceedBacklog ZeroBasedCounter32, tcpEStatsListenerHCSynRcvd ZeroBasedCounter64, tcpEStatsListenerHCInitial ZeroBasedCounter64, tcpEStatsListenerHCEstablished ZeroBasedCounter64, tcpEStatsListenerHCAccepted ZeroBasedCounter64, tcpEStatsListenerHCExceedBacklog ZeroBasedCounter64, tcpEStatsListenerCurConns Gauge32, tcpEStatsListenerMaxBacklog Integer32, tcpEStatsListenerCurBacklog Gauge32, tcpEStatsListenerCurEstabBacklog Gauge32 } tcpEStatsListenerStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time this listener was established. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { tcpEStatsListenerEntry 1 } tcpEStatsListenerSynRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SYNs which have been received for this listener. The total number of failed connections for all reasons can be estimated to be tcpEStatsListenerSynRcvd minus tcpEStatsListenerAccepted and tcpEStatsListenerCurBacklog." ::= { tcpEStatsListenerEntry 2 } tcpEStatsListenerInitial OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections for which the Listener has allocated initial state and placed the connection in the backlog. The may happen in the SYN-RCVD or ESTABLISHED states, depending on the implementation." ::= { tcpEStatsListenerEntry 3 } tcpEStatsListenerEstablished OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of connections which have been established to this endpoint. E.g. The number of first ACKs which have been received for this listener." ::= { tcpEStatsListenerEntry 4 } tcpEStatsListenerAccepted OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections for which the Listener has successfully issued an accept, removing the connection from the backlog." ::= { tcpEStatsListenerEntry 5 } tcpEStatsListenerExceedBacklog OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections dropped from the backlog by this listener due to all reasons. This includes all connections that are allocated initial resources but are not accepted for some reason." ::= { tcpEStatsListenerEntry 6 } tcpEStatsListenerHCSynRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SYNs which have been received for this listener on systems that can process (or reject) more than 1 million connections per second. See tcpEStatsListenerSynRcvd." ::= { tcpEStatsListenerEntry 7 } tcpEStatsListenerHCInitial OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections for which the Listener has allocated initial state and placed the connection in the backlog on systems that can process (or reject) more than 1 million connections per second. See tcpEStatsListenerInitial." ::= { tcpEStatsListenerEntry 8 } tcpEStatsListenerHCEstablished OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of connections which have been established to this endpoint on systems that can process (or reject) more than 1 million connections per second. See tcpEStatsListenerEstablished." ::= { tcpEStatsListenerEntry 9 } tcpEStatsListenerHCAccepted OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections for which the Listener has successfully issued an accept, removing the connection from the backlog on systems that can process (or reject) more than 1 million connections per second. See tcpEStatsListenerAccepted." ::= { tcpEStatsListenerEntry 10 } tcpEStatsListenerHCExceedBacklog OBJECT-TYPE SYNTAX ZeroBasedCounter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of connections dropped from the backlog by this listener due to all reasons on systems that can process (or reject) more than 1 million connections per second. See tcpEStatsListenerHCExceedBacklog." ::= { tcpEStatsListenerEntry 11 } tcpEStatsListenerCurConns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of connections in the ESTABLISHED state, which have also been accepted. It excludes connections that have been established but not accepted because they are still subject to being discarded to shed load without explicit action by either endpoint." ::= { tcpEStatsListenerEntry 12 } tcpEStatsListenerMaxBacklog OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of connections allowed in backlog at one time." ::= { tcpEStatsListenerEntry 13 } tcpEStatsListenerCurBacklog OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of connections that are in backlog. This gauge includes connections in ESTABLISHED or SYN-RECEIVED states for which the Listener has not yet issued an accept. If this listener is using some technique to implicitly represent the SYN-RECEIVED states, e.g. by cryptographically encoding the state information in the initial sequence number (ISS), it MAY elect to exclude connections in the SYN-RECEIVED state from the backlog." ::= { tcpEStatsListenerEntry 14 } tcpEStatsListenerCurEstabBacklog OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of connections in backlog that are in the ESTABLISHED state, but for which the Listener has not yet issued an accept." ::= { tcpEStatsListenerEntry 15 } -- ================================================================ -- -- TCP Connection ID Table -- tcpEStatsConnectIdTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsConnectIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table maps information that uniquely identifies each active TCP connection to the connection ID used by other tables in this MIB Module. It is an extention of tcpConnectionTable in RFC4022. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 2 } tcpEStatsConnectIdEntry OBJECT-TYPE SYNTAX TcpEStatsConnectIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table maps a TCP connection 4-tuple to a connection index." AUGMENTS { tcpConnectionEntry } ::= { tcpEStatsConnectIdTable 1 } TcpEStatsConnectIdEntry ::= SEQUENCE { tcpEStatsConnectIndex Unsigned32 } tcpEStatsConnectIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A unique integer value assigned to each TCP Connection entry. Assignment will begin at 1 and increase to the maximum value and then start again at 1 skipping in use values." ::= { tcpEStatsConnectIdEntry 1 } -- ================================================================ -- -- Basic TCP Performance Statistics -- tcpEStatsPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects that are useful for measuring TCP performance and first line problem diagnosis. Most objects in this table directly expose some TCP state variable or are easily implemented as simple functions (e.g. Maximum) of TCP state variables. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 3 } tcpEStatsPerfEntry OBJECT-TYPE SYNTAX TcpEStatsPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table has information about the characteristics of each active and recently closed tcp connection." INDEX { tcpEStatsConnectIndex } ::= { tcpEStatsPerfTable 1 } TcpEStatsPerfEntry ::= SEQUENCE { tcpEStatsPerfSegsOut ZeroBasedCounter32, tcpEStatsPerfDataSegsOut ZeroBasedCounter32, tcpEStatsPerfDataOctetsOut ZeroBasedCounter32, tcpEStatsPerfHCDataOctetsOut ZeroBasedCounter64, tcpEStatsPerfSegsRetrans ZeroBasedCounter32, tcpEStatsPerfOctetsRetrans ZeroBasedCounter32, tcpEStatsPerfSegsIn ZeroBasedCounter32, tcpEStatsPerfDataSegsIn ZeroBasedCounter32, tcpEStatsPerfDataOctetsIn ZeroBasedCounter32, tcpEStatsPerfHCDataOctetsIn ZeroBasedCounter64, tcpEStatsPerfElapsedSecs ZeroBasedCounter32, tcpEStatsPerfElapsedMicroSecs ZeroBasedCounter32, tcpEStatsPerfStartTimeStamp DateAndTime, tcpEStatsPerfCurMSS Gauge32, tcpEStatsPerfPipeSize Gauge32, tcpEStatsPerfMaxPipeSize Gauge32, tcpEStatsPerfSmoothedRTT Gauge32, tcpEStatsPerfCurRTO Gauge32, tcpEStatsPerfCongSignals ZeroBasedCounter32, tcpEStatsPerfCurCwnd Gauge32, tcpEStatsPerfCurSsthresh Gauge32, tcpEStatsPerfTimeouts ZeroBasedCounter32, tcpEStatsPerfCurRwinSent Gauge32, tcpEStatsPerfMaxRwinSent Gauge32, tcpEStatsPerfZeroRwinSent Gauge32, tcpEStatsPerfCurRwinRcvd Gauge32, tcpEStatsPerfMaxRwinRcvd Gauge32, tcpEStatsPerfZeroRwinRcvd Gauge32, tcpEStatsPerfSndLimTransRwin ZeroBasedCounter32, tcpEStatsPerfSndLimTransCwnd ZeroBasedCounter32, tcpEStatsPerfSndLimTransSnd ZeroBasedCounter32, tcpEStatsPerfSndLimTimeRwin ZeroBasedCounter32, tcpEStatsPerfSndLimTimeCwnd ZeroBasedCounter32, tcpEStatsPerfSndLimTimeSnd ZeroBasedCounter32 } -- -- The following objects provide statistics on aggregate -- segments and data sent on a connection. These provide a -- direct measure of the Internet capacity consumed by a -- connection. -- tcpEStatsPerfSegsOut OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of segments sent." ::= { tcpEStatsPerfEntry 1 } tcpEStatsPerfDataSegsOut OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of segments sent containing a positive length data segment." ::= { tcpEStatsPerfEntry 2 } tcpEStatsPerfDataOctetsOut OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of data contained in transmitted segments, including retransmitted data. Note that this does not include TCP headers." ::= { tcpEStatsPerfEntry 3 } tcpEStatsPerfHCDataOctetsOut OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets of data contained in transmitted segments, including retransmitted data, on systems that can transmit more than 10 million bits per second. Note that this does not include TCP headers." ::= { tcpEStatsPerfEntry 4 } tcpEStatsPerfSegsRetrans OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of segments transmitted containing at least some retransmitted data." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 5 } tcpEStatsPerfOctetsRetrans OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets retransmitted." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 6 } tcpEStatsPerfSegsIn OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of segments received." ::= { tcpEStatsPerfEntry 7 } tcpEStatsPerfDataSegsIn OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of segments received containing a positive length data segment." ::= { tcpEStatsPerfEntry 8 } tcpEStatsPerfDataOctetsIn OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in received data segments, including retransmitted data. Note that this does not include TCP headers." ::= { tcpEStatsPerfEntry 9 } tcpEStatsPerfHCDataOctetsIn OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets contained in received data segments, including retransmitted data, on systems that can receive more than 10 million bits per second. Note that this does not include TCP headers." ::= { tcpEStatsPerfEntry 10 } tcpEStatsPerfElapsedSecs OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The seconds part of the time elapsed between tcpEStatsPerfStartTimeStamp and the most recent protocol event (segment sent or received)." ::= { tcpEStatsPerfEntry 11 } tcpEStatsPerfElapsedMicroSecs OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "microseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The micro-second part of time elapsed between tcpEStatsPerfStartTimeStamp to the most recent protocol event (segment sent or received). This may be updated in what ever time granularity is the system supports." ::= { tcpEStatsPerfEntry 12 } tcpEStatsPerfStartTimeStamp OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Time at which this row was created and all ZeroBasedCounters in the row were initialized to zero." ::= { tcpEStatsPerfEntry 13 } -- -- The following objects can be used to fit minimal -- performance models to the TCP data rate. -- tcpEStatsPerfCurMSS OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current maximum segment size (MSS), in octets." REFERENCE "RFC1122, Requirements for Internet Hosts - Communication Layers" ::= { tcpEStatsPerfEntry 14 } tcpEStatsPerfPipeSize OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP senders current estimate of the number of unacknowledged data octets in the network. While not in recovery (e.g. while the receiver is not reporting missing data to the sender) this is precisely the same as ``Flight size'' as defined in RFC2581, which can be computed as SND.NXT minus SND.UNA. [RFC793] During recovery the TCP sender has incomplete information about the state of the network (e.g. which segments are lost vs reordered, especially if the return path is also dropping TCP acknowledgments). Current TCP standards do not mandate any specific algorithm for estimating the number of unacknowledged data octets in the network. RFC3517 describes a conservative algorithm to use SACK information to estimate the number of unacknowledged data octets in the network. tcpEStatsPerfPipeSize object SHOULD be the the same as ``pipe'' as defined in in RFC3517 if it is implemented. (Note that while not in recovery the pipe algorithm yields the same values as flight size). If RFC3517 is not implemented, the data octets in flight SHOULD be estimated as SND.NXT minus SND.UNA adjusted by some measure of the data that has left the network and retransmitted data. For example, with Reno or NewReno style TCP, the number of duplicate acknowledgment is used to count the number of segments that have left the network. I.e.: PipeSize=SND.NXT-SND.UNA+(retransmits-dupacks)*CurMSS" REFERENCE "RFC793, RFC2581, RFC3517" ::= { tcpEStatsPerfEntry 15 } tcpEStatsPerfMaxPipeSize OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of tcpEStatsPerfPipeSize, for this connection." REFERENCE "RFC793, RFC2581, RFC3517" ::= { tcpEStatsPerfEntry 16 } tcpEStatsPerfSmoothedRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The smoothed round trip time used in calculation of the RTO. See SRTT in [RFC2988]." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPerfEntry 17 } tcpEStatsPerfCurRTO OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The current value of the retransmit timer RTO." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPerfEntry 18 } tcpEStatsPerfCongSignals OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of multiplicative downward congestion window adjustments due to all forms of congestion signals, including Fast Retransmit, ECN and timeouts. This object summarizes all events that invoke the MD portion of AIMD congestion control, and as such is the best indicator of how cwnd is being affected by congestion. Note that retransmission timeouts multiplicatively reduce the window implicitly by setting ssthresh, and SHOULD be included in tcpEStatsPerfCongSignals. In order to minimize spurious congestion indications due to out-of-order segments, tcpEStatsPerfCongSignals SHOULD be incremented in association with the Fast Retransmit algorithm." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPerfEntry 19 } tcpEStatsPerfCurCwnd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current congestion window, in octets." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPerfEntry 20 } tcpEStatsPerfCurSsthresh OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current slow start threshold in octets." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPerfEntry 21 } tcpEStatsPerfTimeouts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the retransmit timeout has expired when the RTO backoff multiplier is equal to one." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPerfEntry 22 } -- -- The following objects instrument receiver window updates -- sent by the local receiver to the remote sender. These can -- be used to determine if the local receiver is exerting flow -- control back pressure on the remote sender. -- tcpEStatsPerfCurRwinSent OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The most recent window advertisement sent, in octets." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 23 } tcpEStatsPerfMaxRwinSent OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum window advertisement sent, in octets." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 24 } tcpEStatsPerfZeroRwinSent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of acknowledgments sent announcing a zero receive window, when the previously announced window was not zero." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 25 } -- -- The following objects instrument receiver window updates -- from the far end-system to determine if the remote receiver -- has sufficient buffer space or is exerting flow-control -- back pressure on the local sender. -- tcpEStatsPerfCurRwinRcvd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The most recent window advertisement received, in octets." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 26 } tcpEStatsPerfMaxRwinRcvd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum window advertisement received, in octets." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 27 } tcpEStatsPerfZeroRwinRcvd OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of acknowledgments received announcing a zero receive window, when the previously announced window was not zero." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsPerfEntry 28 } -- -- The following optional objects can be used to quickly -- identify which subsystems are limiting TCP performance. -- There are three parallel pairs of instruments that measure -- the extent to which TCP performance is limited by the -- announced receiver window (indicating a receiver -- bottleneck), the current congestion window or -- retransmission timeout (indicating a path bottleneck) and -- all others events (indicating a sender bottleneck). -- -- These instruments SHOULD be updated every time the TCP -- output routine stops sending data. The elapsed time since -- the previous stop is accumulated into the appropriate -- object as determined by the previous stop reason (e.g. stop -- state). The current stop reason determines which timer will -- be updated the next time TCP output stops. -- -- Since there is no explicit stop at the beginning of a -- timeout, it is necessary to retroactively reclassify the -- previous stop as 'Congestion Limited'. -- tcpEStatsPerfSndLimTransRwin OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transitions into the 'Receiver Limited' state from either the 'Congestion Limited' or 'Sender Limited' states. This state is entered whenever TCP transmission stops because the sender has filled the announced receiver window." ::= { tcpEStatsPerfEntry 31 } tcpEStatsPerfSndLimTransCwnd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transitions into the 'Congestion Limited' state from either the 'Receiver Limited' or 'Sender Limited' states. This state is entered whenever TCP transmission stops because the sender has reached some limit defined by congestion control (e.g. cwnd) or other algorithms (retransmission timeouts) designed to control network traffic." ::= { tcpEStatsPerfEntry 32 } tcpEStatsPerfSndLimTransSnd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transitions into the 'Sender Limited' state from either the 'Receiver Limited' or 'Congestion Limited' states. This state is entered whenever TCP transmission stops due to some sender limit such as running out of application data or other resources and the Karn algorithm. When TCP stops sending data for any reason which can not be classified as Receiver Limited or Congestion Limited it MUST be treated as Sender Limited." ::= { tcpEStatsPerfEntry 33 } tcpEStatsPerfSndLimTimeRwin OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The cumulative time spent in the 'Receiver Limited' state. See tcpEStatsPerfSndLimTransRwin." ::= { tcpEStatsPerfEntry 34 } tcpEStatsPerfSndLimTimeCwnd OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The cumulative time spent in the 'Congestion Limited' state. See tcpEStatsPerfSndLimTransCwnd. When there is a retransmission timeout, it SHOULD be counted in tcpEStatsPerfSndLimTimeCwnd (and not the cumulative time for some other state.)" ::= { tcpEStatsPerfEntry 35 } tcpEStatsPerfSndLimTimeSnd OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The cumulative time spent in the 'Sender Limited' state. See tcpEStatsPerfSndLimTransSnd." ::= { tcpEStatsPerfEntry 36 } -- ================================================================ -- -- Statistics for diagnosing path problems -- tcpEStatsPathTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsPathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects that can be used to infer detailed behavior of the Internet path, such as the extent that there is reordering, ECN bits and if RTT fluctuations are correlated to losses. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 4 } tcpEStatsPathEntry OBJECT-TYPE SYNTAX TcpEStatsPathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table has information about the characteristics of each active and recently closed tcp connection." INDEX { tcpEStatsConnectIndex } ::= { tcpEStatsPathTable 1 } TcpEStatsPathEntry ::= SEQUENCE { tcpEStatsPathRetranThresh Gauge32, tcpEStatsPathNonRecovDAEpisodes Integer32, tcpEStatsPathSumOctetsReordered Integer32, tcpEStatsPathNonRecovDA ZeroBasedCounter32, tcpEStatsPathSampleRTT Gauge32, tcpEStatsPathRTTVar Gauge32, tcpEStatsPathMaxRTT Gauge32, tcpEStatsPathMinRTT Gauge32, tcpEStatsPathSumRTT ZeroBasedCounter32, tcpEStatsPathHCSumRTT ZeroBasedCounter64, tcpEStatsPathCountRTT ZeroBasedCounter32, tcpEStatsPathMaxRTO Gauge32, tcpEStatsPathMinRTO Gauge32, tcpEStatsPathIpTtl Integer32, tcpEStatsPathIpTosIn Integer32, tcpEStatsPathIpTosOut Integer32, tcpEStatsPathPreCongSumCwnd ZeroBasedCounter32, tcpEStatsPathPreCongSumRTT ZeroBasedCounter32, tcpEStatsPathPostCongSumRTT ZeroBasedCounter32, tcpEStatsPathPostCongCountRTT ZeroBasedCounter32, tcpEStatsPathECNsignals ZeroBasedCounter32, tcpEStatsPathECERcvd ZeroBasedCounter32, tcpEStatsPathQuenchRcvd ZeroBasedCounter32, tcpEStatsPathDupAckEpisodes ZeroBasedCounter32, tcpEStatsPathRcvRTT Gauge32, tcpEStatsPathDupAcksOut ZeroBasedCounter32, tcpEStatsPathCERcvd ZeroBasedCounter32, tcpEStatsPathECNSent ZeroBasedCounter32, tcpEStatsPathECNNonceRcvd ZeroBasedCounter32 } -- -- The following optional objects can be used to infer segment -- reordering on the path from the local sender to the remote -- receiver. -- tcpEStatsPathRetranThresh OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of duplicate acknowledgments required to trigger Fast Retransmit. Note that although this is constant in traditional Reno TCP implementations, it is adaptive in many newer TCPs." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPathEntry 1 } tcpEStatsPathNonRecovDAEpisodes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of duplicate acknowledgment episodes that did not trigger a Fast Retransmit because ACK advanced prior to the number of duplicate acknowledgments reaching RetranThresh. In many implementations this is the number of times the 'dupacks' counter is set to zero when it is non-zero but less than RetranThresh. Note that the change in tcpEStatsPathNonRecovDAEpisodes divided by the change in tcpEStatsPerfDataSegsOut is an estimate of the frequency of data reordering on the forward path over some interval." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPathEntry 2 } tcpEStatsPathSumOctetsReordered OBJECT-TYPE SYNTAX Integer32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of the amounts SND.UNA advances on the acknowledgment which ends a dup-ack episode without a retransmission. Note the change in tcpEStatsPathSumOctetsReordered divided by the change in tcpEStatsPathNonRecovDAEpisodes is an estimates of the average reordering distance, over some interval." ::= { tcpEStatsPathEntry 3 } tcpEStatsPathNonRecovDA OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Duplicate acks (or SACKS) that did not trigger a Fast Retransmit because ACK advanced prior to the number of duplicate acknowledgments reaching RetranThresh. In many implementations, this is the sum of the 'dupacks' counter, just before it is set to zero because ACK advanced without a Fast Retransmit. Note that the change in tcpEStatsPathNonRecovDA divided by the change in tcpEStatsPathNonRecovDAEpisodes is an estimate of the average reordering distance in segments over some interval." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPathEntry 4 } -- -- The following optional objects instrument the round trip -- time estimator and the retransmission timeout timer. -- tcpEStatsPathSampleRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The most recent raw round trip time measurement used in calculation of the RTO." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 11 } tcpEStatsPathRTTVar OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The round trip time variation used in calculation of the RTO. See RTTVAR in [RFC2988]." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 12 } tcpEStatsPathMaxRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum sampled round trip time." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 13 } tcpEStatsPathMinRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum sampled round trip time." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 14 } tcpEStatsPathSumRTT OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all sampled round trip times. Note that the change in tcpEStatsPathSumRTT divided by the change in tcpEStatsPathCountRTT is the mean RTT, uniformly averaged over an enter interval." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 15 } tcpEStatsPathHCSumRTT OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all sampled round trip times, on all systems that implement multiple concurrent RTT measurements. Note that the change in tcpEStatsPathHCSumRTT divided by the change in tcpEStatsPathCountRTT is the mean RTT, uniformly averaged over an enter interval." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 16 } tcpEStatsPathCountRTT OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of round trip time samples included in tcpEStatsPathSumRTT and tcpEStatsPathHCSumRTT." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 17 } tcpEStatsPathMaxRTO OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of the retransmit timer RTO." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 18 } tcpEStatsPathMinRTO OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum value of the retransmit timer RTO." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsPathEntry 19 } -- -- The following optional objects provide information about -- how TCP is using the IP layer. -- tcpEStatsPathIpTtl OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the TTL field carried in the most recently received IP header. This is sometimes useful to detect changing or unstable routes." REFERENCE "RFC791, Internet Protocol" ::= { tcpEStatsPathEntry 20 } tcpEStatsPathIpTosIn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the IPv4 Type Of Service octet, or the IPv6 traffic class octet, carried in the most recently received IP header. This is useful to diagnose interactions between TCP and any IP layer packet scheduling and delivery policy, which might be in effect to implement Diffserv." REFERENCE "RFC3260, New Terminology and Clarifications for Diffserv" ::= { tcpEStatsPathEntry 21 } tcpEStatsPathIpTosOut OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the IPv4 Type Of Service octet, or the IPv6 traffic class octet, carried in the most recently transmitted IP header. This is useful to diagnose interactions between TCP and any IP layer packet scheduling and delivery policy, which might be in effect to implement Diffserv." REFERENCE "RFC3260, New Terminology and Clarifications for Diffserv" ::= { tcpEStatsPathEntry 22 } -- -- The following optional objects characterize the congestion -- feedback signals by collecting statistics on how the -- congestion events are correlated to losses, changes in RTT -- and other protocol events. -- tcpEStatsPathPreCongSumCwnd OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of the values of the congestion window, in octets, captured each time a congestion signal is received. This MUST be updated each time tcpEStatsPerfCongSignals is incremented, such that the change in tcpEStatsPathPreCongSumCwnd divided by the change in tcpEStatsPerfCongSignals is the average window (over some interval) just prior to a congestion signal." ::= { tcpEStatsPathEntry 23 } tcpEStatsPathPreCongSumRTT OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of the last sample of the RTT (tcpEStatsPathSampleRTT) prior to received congestion signals. This MUST be updated each time tcpEStatsPerfCongSignals is incremented, such that the change in tcpEStatsPathPreCongSumRTT divided by the change in tcpEStatsPerfCongSignals is the average RTT (over some interval) just prior to a congestion signal." ::= { tcpEStatsPathEntry 24 } tcpEStatsPathPostCongSumRTT OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Sum of the first sample of the RTT (tcpEStatsPathSampleRTT) following each congestion signal. Such that the change in tcpEStatsPathPostCongSumRTT divided by the change in tcpEStatsPathPostCongCountRTT is the average RTT (over some interval) just after a congestion signal." ::= { tcpEStatsPathEntry 25 } tcpEStatsPathPostCongCountRTT OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTT samples included in tcpEStatsPathPostCongSumRTT such that the change in tcpEStatsPathPostCongSumRTT divided by the change in tcpEStatsPathPostCongCountRTT is the average RTT (over some interval) just after a congestion signal." ::= { tcpEStatsPathEntry 26 } -- -- The following optional objects can be used to detect other -- types of non-loss congestion signals such as source quench -- or ECN. -- tcpEStatsPathECNsignals OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of congestion signals delivered via explicit congestion notification (ECN). This is the number of segments bearing ECE bits or failing the ECN nonce check." REFERENCE "RFC3168, The Addition of Explicit Congestion Notification (ECN) to IP" ::= { tcpEStatsPathEntry 27 } tcpEStatsPathECERcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of congestion signals received via the ECE bit." REFERENCE "RFC3168, The Addition of Explicit Congestion Notification (ECN) to IP" ::= { tcpEStatsPathEntry 28 } tcpEStatsPathQuenchRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP quench messages that are treated as congestion signals." ::= { tcpEStatsPathEntry 29 } -- -- The following optional objects are receiver side -- instruments of the path from the sender to the receiver. In -- general the receiver has less information about the state -- of the path, because the receiver does not have a robust -- mechanism to infer the sender's actions. -- tcpEStatsPathDupAckEpisodes OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Duplicate Acks Sent when prior Ack was not duplicate. This is the number of times that a contiguous series of duplicate acknowledgments have been sent. This is an indication of the number of data segments lost or reordered on the path from the remote TCP endpoint to the near TCP endpoint." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPathEntry 30 } tcpEStatsPathRcvRTT OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The receiver's estimate of the Path RTT. Adaptive receiver window algorithms depend on the receiver to having a good estimate of the path RTT." ::= { tcpEStatsPathEntry 31 } tcpEStatsPathDupAcksOut OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of duplicate ACKs sent. The ratio of the change in tcpEStatsPathDupAcksOut to the change in tcpEStatsPathDupAckEpisodes is an indication of reorder or recovery distance over some interval." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsPathEntry 32 } tcpEStatsPathCERcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Received segments with Congestion Experienced bits." REFERENCE "RFC3168, The Addition of Explicit Congestion Notification (ECN) to IP" ::= { tcpEStatsPathEntry 33 } tcpEStatsPathECNSent OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times CE bits have set ECN." REFERENCE "RFC3168, The Addition of Explicit Congestion Notification (ECN) to IP" ::= { tcpEStatsPathEntry 34 } tcpEStatsPathECNNonceRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ECN Nonces received. Note that the low bit is the same as the one bit nonce sum." REFERENCE "RFC3540, Robust Explicit Congestion Notification (ECN) Signaling with Nonces" ::= { tcpEStatsPathEntry 35 } -- ================================================================ -- -- Statistics for diagnosing stack algorithms -- tcpEStatsStackTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects that are most useful for determining how well some of the TCP control algorithms are coping with this particular path. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 5 } tcpEStatsStackEntry OBJECT-TYPE SYNTAX TcpEStatsStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table has information about the characteristics of each active and recently closed tcp connection." INDEX { tcpEStatsConnectIndex } ::= { tcpEStatsStackTable 1 } TcpEStatsStackEntry ::= SEQUENCE { tcpEStatsStackActiveOpen TruthValue, tcpEStatsStackMSSSent Unsigned32, tcpEStatsStackMSSRcvd Unsigned32, tcpEStatsStackWinScaleSent Integer32, tcpEStatsStackWinScaleRcvd Integer32, tcpEStatsStackTimeStamps TcpEStatsNegotiated, tcpEStatsStackECN TcpEStatsNegotiated, tcpEStatsStackWillSendSACK TcpEStatsNegotiated, tcpEStatsStackWillUseSACK TcpEStatsNegotiated, tcpEStatsStackState INTEGER, tcpEStatsStackNagle TruthValue, tcpEStatsStackMaxSsCwnd Gauge32, tcpEStatsStackMaxCaCwnd Gauge32, tcpEStatsStackMaxSsthresh Gauge32, tcpEStatsStackMinSsthresh Gauge32, tcpEStatsStackInRecovery INTEGER, tcpEStatsStackDupAcksIn ZeroBasedCounter32, tcpEStatsStackSpuriousFrDetected ZeroBasedCounter32, tcpEStatsStackSpuriousRtoDetected ZeroBasedCounter32, tcpEStatsStackSoftErrors ZeroBasedCounter32, tcpEStatsStackSoftErrorReason INTEGER, tcpEStatsStackSlowStart ZeroBasedCounter32, tcpEStatsStackCongAvoid ZeroBasedCounter32, tcpEStatsStackOtherReductions ZeroBasedCounter32, tcpEStatsStackCongOverCount ZeroBasedCounter32, tcpEStatsStackFastRetran ZeroBasedCounter32, tcpEStatsStackSubsequentTimeouts ZeroBasedCounter32, tcpEStatsStackCurTimeoutCount Gauge32, tcpEStatsStackAbruptTimeouts ZeroBasedCounter32, tcpEStatsStackSACKsRcvd ZeroBasedCounter32, tcpEStatsStackSACKBlocksRcvd ZeroBasedCounter32, tcpEStatsStackSendStall ZeroBasedCounter32, tcpEStatsStackDSACKDups ZeroBasedCounter32, tcpEStatsStackMaxMSS Gauge32, tcpEStatsStackMinMSS Gauge32, tcpEStatsStackSndInitial Counter32, tcpEStatsStackRecInitial Counter32, tcpEStatsStackCurRetxQueue Gauge32, tcpEStatsStackMaxRetxQueue Gauge32, tcpEStatsStackCurReasmQueue Gauge32, tcpEStatsStackMaxReasmQueue Gauge32 } -- -- The following objects reflect TCP options carried on the -- SYN or SYN-ACK. These options are used to provide -- additional protocol parameters or to enable various -- optional TCP features or algorithms. -- -- Except as noted, the TCP protocol does not permit these -- options to change after the SYN exchange. -- tcpEStatsStackActiveOpen OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True(1) if the local connection traversed the SYN-SENT state, else false(2)." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 1 } tcpEStatsStackMSSSent OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value sent in an MSS option, or zero if none." REFERENCE "RFC1122, Requirements for Internet Hosts - Communication Layers" ::= { tcpEStatsStackEntry 2 } tcpEStatsStackMSSRcvd OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value received in an MSS option, or zero if none." REFERENCE "RFC1122, Requirements for Internet Hosts - Communication Layers" ::= { tcpEStatsStackEntry 3 } tcpEStatsStackWinScaleSent OBJECT-TYPE SYNTAX Integer32 (-1..14) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the transmitted window scale option if one was sent; otherwise, a value of -1. Note that if both tcpEStatsStackWinScaleSent and tcpEStatsStackWinScaleRcvd are not -1, then Rcv.Wind.Scale will be the same as this value and used to scale receiver window announcements from the local host to the remote host." REFERENCE "RFC1323, TCP Extensions for High Performance" ::= { tcpEStatsStackEntry 4 } tcpEStatsStackWinScaleRcvd OBJECT-TYPE SYNTAX Integer32 (-1..14) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the received window scale option if one was received; otherwise, a value of -1. Note that if both tcpEStatsStackWinScaleSent and tcpEStatsStackWinScaleRcvd are not -1, then Snd.Wind.Scale will be the same as this value and used to scale receiver window announcements from the remote host to the local host." REFERENCE "RFC1323, TCP Extensions for High Performance" ::= { tcpEStatsStackEntry 5 } tcpEStatsStackTimeStamps OBJECT-TYPE SYNTAX TcpEStatsNegotiated MAX-ACCESS read-only STATUS current DESCRIPTION "Enabled(1) if TCP timestamps have been negotiated on, selfDisabled(2) if they are disabled or not implemented on the local host, or peerDisabled(3) if not negotiated by the remote hosts." REFERENCE "RFC1323, TCP Extensions for High Performance" ::= { tcpEStatsStackEntry 6 } tcpEStatsStackECN OBJECT-TYPE SYNTAX TcpEStatsNegotiated MAX-ACCESS read-only STATUS current DESCRIPTION "Enabled(1) if Explicit Congestion Notification (ECN) has been negotiated on, selfDisabled(2) if it is disabled or not implemented on the local host, or peerDisabled(3) if not negotiated by the remote hosts." REFERENCE "RFC3168, The Addition of Explicit Congestion Notification (ECN) to IP" ::= { tcpEStatsStackEntry 7 } tcpEStatsStackWillSendSACK OBJECT-TYPE SYNTAX TcpEStatsNegotiated MAX-ACCESS read-only STATUS current DESCRIPTION "Enabled(1) if the local host will send SACK options selfDisabled(2) if SACK is disabled or not implemented on the local host, or peerDisabled(3) if the remote host did not send the SACK-permitted option. Note that SACK negotiation is not symmetrical. SACK can enabled on one side of the connection and not the other." REFERENCE "RFC2018, TCP Selective Acknowledgement Options" ::= { tcpEStatsStackEntry 8 } tcpEStatsStackWillUseSACK OBJECT-TYPE SYNTAX TcpEStatsNegotiated MAX-ACCESS read-only STATUS current DESCRIPTION "Enabled(1) if the local host will process SACK options selfDisabled(2) if SACK is disabled or not implemented on the local host, or peerDisabled(3) if the remote host sends duplicate ACKs without SACK options, or the local host otherwise decides not to process received SACK options. Unlike other TCP options, the remote data receiver can not explicitly indicate if it is able to generate SACK options. When sending data, the local host has to deduce if the remote receiver is sending SACK options. This object can transition from Enabled(1) to peerDisabled(3) after the SYN exchange. Note that SACK negotiation is not symmetrical. SACK can enabled on one side of the connection and not the other." REFERENCE "RFC2018, TCP Selective Acknowledgement Options" ::= { tcpEStatsStackEntry 9 } -- -- The following two objects reflect the current state of the -- connection. -- tcpEStatsStackState OBJECT-TYPE SYNTAX INTEGER { tcpESStateClosed(1), tcpESStateListen(2), tcpESStateSynSent(3), tcpESStateSynReceived(4), tcpESStateEstablished(5), tcpESStateFinWait1(6), tcpESStateFinWait2(7), tcpESStateCloseWait(8), tcpESStateLastAck(9), tcpESStateClosing(10), tcpESStateTimeWait(11), tcpESStateDeleteTcb(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value representing the connection state from the TCP State Transition Diagram. The value listen(2) is included only for parallelism to the old tcpConnTable, and SHOULD NOT be used because the listen state in managed by the tcpListenerTable. The value DeleteTcb(12) is included only for parallelism to the tcpConnTable mechanism for terminating connections, although this table does not permit writing." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 10 } tcpEStatsStackNagle OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True(1) if the Nagle algorithm is being used, else false(2)." REFERENCE "RFC1122, Requirements for Internet Hosts - Communication Layers" ::= { tcpEStatsStackEntry 11 } -- -- The following objects instrument the overall operation of -- TCP congestion control and data retransmissions. These -- instruments are sufficient to fit the actual performance to -- an updated macroscopic performance model [RFC2581] [Mat97] -- [Pad98]. -- tcpEStatsStackMaxSsCwnd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum congestion window used during Slow Start, in octets." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 12 } tcpEStatsStackMaxCaCwnd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum congestion window used during Congestion Avoidance, in octets." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 13 } tcpEStatsStackMaxSsthresh OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum slow start threshold, excluding the initial value." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 14 } tcpEStatsStackMinSsthresh OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum slow start threshold." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 15 } tcpEStatsStackInRecovery OBJECT-TYPE SYNTAX INTEGER { tcpESDataContiguous(1), tcpESDataUnordered(2), tcpESDataRecovery(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "An integer value representing the state of the loss recovery for this connection. tcpESDataContiguous(1) indicates that the remote receiver is reporting contiguous data (no duplicate acknowledgments or SACK options) and that there are no unacknowledged retransmissions. tcpESDataUnordered(2) indicates that the remote receiver is reporting missing or out-of-order data (e.g. sending duplicate acknowledgments or SACK options) and that there are no unacknowledged retransmissions (because the missing data has not yet been retransmitted). tcpESDataRecovery(3) indicates that the sender has outstanding retransmitted data which is still unacknowledged." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 16 } tcpEStatsStackDupAcksIn OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of duplicate ACKs received." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 17 } tcpEStatsStackSpuriousFrDetected OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of acknowledgments reporting out-of-order segments after the Fast Retransmit algorithm has already retransmitted the segments. (For example as detected by the Eifel algorithm).'" REFERENCE "RFC3522, The Eifel Detection Algorithm for TCP" ::= { tcpEStatsStackEntry 18 } tcpEStatsStackSpuriousRtoDetected OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of acknowledgments reporting segments that have already be retransmitted due to a Retransmission Timeout." ::= { tcpEStatsStackEntry 19 } -- -- The following optional objects instrument unusual protocol -- events that probably indicate implementation problems in -- the protocol or path. -- tcpEStatsStackSoftErrors OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of segments that fail various consistency tests during TCP input processing. Soft errors might cause the segment to be discard but some do not. Some of these soft errors cause the generation of a TCP acknowledgment, others are silently discarded." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 21 } tcpEStatsStackSoftErrorReason OBJECT-TYPE SYNTAX INTEGER { belowDataWindow(1), aboveDataWindow(2), belowAckWindow(3), aboveAckWindow(4), belowTSWindow(5), aboveTSWindow(6), dataCheckSum(7), otherSoftError(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identities which consistency test most recently failed during tcp input processing. This object SHOULD be set every time tcpEStatsStackSoftErrors is incremented. The codes are as follows: belowDataWindow(1) - All data in the segment is below SND.UNA. (Normal for keep-alives and zero window probes). aboveDataWindow(2) - Some data in the segment is above SND.WND. (Indicates an implementation bug or serious fraud). belowAckWindow(3) - ACK below SND.UNA. (Indicates that the return path is reordering ACKs) aboveAckWindow(4) - An ACK for data that we have not sent. (Indicates an implementation bug or serious fraud). belowTSWindow(5) - TSecr on the segment is older than the current TS.Recent (Normal for the rare case where PAWS detects data reordered by the network.) aboveTSWindow(6) - TSecr on the segment is newer than the current TS.Recent. (Indicates an implementation bug or serious fraud). dataCheckSum(7) - Incorrect checksum. Note that this value is intrinsically fragile, because the header fields used to identify the connection may have been corrupted. otherSoftError(8) - All other soft errors not listed above.'" REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 22 } -- -- The following optional objects expose the detailed -- operation of the congestion control algorithms. -- tcpEStatsStackSlowStart OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the congestion window has been increased by the Slow Start algorithm." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 23 } tcpEStatsStackCongAvoid OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the congestion window has been increased by the Congestion Avoidance algorithm." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 24 } tcpEStatsStackOtherReductions OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of congestion window reductions made as a result of anything other than AIMD congestion control algorithms. Examples of non-multiplicative window reductions include Congestion Window Validation [RFC2861] and experimental algorithms such as Vegas [Bra94]. All window reductions MUST be counted as either tcpEStatsPerfCongSignals or tcpEStatsStackOtherReductions." REFERENCE "RFC2861, TCP Congestion Window Validation" ::= { tcpEStatsStackEntry 25 } tcpEStatsStackCongOverCount OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of congestion events which were 'backed out' of the congestion control state machine such that the congestion window was restored to a prior value. This can happen due to the Eifel algorithm [RFC3522] or other algorithms which can be used to detect and cancel spurious invocations of the Fast Retransmit Algorithm. Although it may be feasible to undo the effects of spurious invocation of the Fast Retransmit congestion events can not easily be backed out of tcpEStatsPerfCongSignals and tcpEStatsPathPreCongSumCwnd, etc." REFERENCE "RFC3522, The Eifel Detection Algorithm for TCP" ::= { tcpEStatsStackEntry 26 } tcpEStatsStackFastRetran OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of invocations of the Fast Retransmit algorithm." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 27 } tcpEStatsStackSubsequentTimeouts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the retransmit timeout has expired after the RTO has been doubled. See section 5.5 in RFC2988." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsStackEntry 28 } tcpEStatsStackCurTimeoutCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of times the retransmit timeout has expired without receiving an acknowledgment for new data. tcpEStatsStackCurTimeoutCount is reset to zero when new data is acknowledged and incremented for each invocation of section 5.5 in RFC2988." REFERENCE "RFC2988, Computing TCP's Retransmission Timer" ::= { tcpEStatsStackEntry 29 } tcpEStatsStackAbruptTimeouts OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of timeouts that occurred without any immediately preceding duplicate acknowledgments or other indications of congestion. Abrupt Timeouts indicate that the path lost an entire window of data or acknowledgments. Timeouts that are preceded by duplicate acknowledgments or other congestion signals (e.g. ECN) are not counted as abrupt, and might have been avoided by a more sophisticated Fast Retransmit algorithm." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsStackEntry 30 } tcpEStatsStackSACKsRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SACK options received." REFERENCE "RFC2018, TCP Selective Acknowledgement Options" ::= { tcpEStatsStackEntry 31 } tcpEStatsStackSACKBlocksRcvd OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SACK blocks received (within SACK options)." REFERENCE "RFC2018, TCP Selective Acknowledgement Options" ::= { tcpEStatsStackEntry 32 } tcpEStatsStackSendStall OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interface stalls or other sender local resource limitations that are treated as congestion signals." ::= { tcpEStatsStackEntry 33 } tcpEStatsStackDSACKDups OBJECT-TYPE SYNTAX ZeroBasedCounter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of duplicate segments reported to the local host by D-SACK blocks." REFERENCE "RFC2883, An Extension to the Selective Acknowledgement (SACK) Option for TCP" ::= { tcpEStatsStackEntry 34 } -- -- The following optional objects instrument path MTU -- discovery. -- tcpEStatsStackMaxMSS OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum MSS, in octets." REFERENCE "RFC1191, Path MTU discovery" ::= { tcpEStatsStackEntry 35 } tcpEStatsStackMinMSS OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum MSS, in octets." REFERENCE "RFC1191, Path MTU discovery" ::= { tcpEStatsStackEntry 36 } -- -- The following optional initial value objects are useful for -- conformance testing instruments on application progress and -- consumed network resources. -- tcpEStatsStackSndInitial OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Initial send sequence number. Note that by definition tcpEStatsStackSndInitial never changes for a given connection." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 37 } tcpEStatsStackRecInitial OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Initial receive sequence number. Note that by definition tcpEStatsStackRecInitial never changes for a given connection." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsStackEntry 38 } -- -- The following optional objects instrument the senders -- buffer usage, including any buffering in the application -- interface to TCP and the retransmit queue. All 'buffer -- memory' instruments are assumed to include OS data -- structure overhead. -- tcpEStatsStackCurRetxQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of octets of data occupying the retransmit queue." ::= { tcpEStatsStackEntry 39 } tcpEStatsStackMaxRetxQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of octets of data occupying the retransmit queue." ::= { tcpEStatsStackEntry 40 } tcpEStatsStackCurReasmQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of octets of sequence space spanned by the reassembly queue. This is generally the difference between rcv.nxt and the sequence number of the right most edge of the reassembly queue." ::= { tcpEStatsStackEntry 41 } tcpEStatsStackMaxReasmQueue OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value of tcpEStatsStackCurReasmQueue" ::= { tcpEStatsStackEntry 42 } -- ================================================================ -- -- Statistics for diagnosing interactions between -- applications and TCP. -- tcpEStatsAppTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsAppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains objects that are useful for determining if the application using TCP is limiting TCP performance. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 6 } tcpEStatsAppEntry OBJECT-TYPE SYNTAX TcpEStatsAppEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table has information about the characteristics of each active and recently closed tcp connection." INDEX { tcpEStatsConnectIndex } ::= { tcpEStatsAppTable 1 } TcpEStatsAppEntry ::= SEQUENCE { tcpEStatsAppSndUna Counter32, tcpEStatsAppSndNxt Integer32, tcpEStatsAppSndMax Counter32, tcpEStatsAppThruOctetsAcked ZeroBasedCounter32, tcpEStatsAppHCThruOctetsAcked ZeroBasedCounter64, tcpEStatsAppRcvNxt Counter32, tcpEStatsAppThruOctetsReceived ZeroBasedCounter32, tcpEStatsAppHCThruOctetsReceived ZeroBasedCounter64, tcpEStatsAppCurAppWQueue Gauge32, tcpEStatsAppMaxAppWQueue Gauge32, tcpEStatsAppCurAppRQueue Gauge32, tcpEStatsAppMaxAppRQueue Gauge32 } -- -- The following objects provide throughput statistics for the -- connection including sequence numbers and elapsed -- application data. These permit direct observation of the -- applications progress, in terms of elapsed data delivery -- and elapsed time. -- tcpEStatsAppSndUna OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of SND.UNA, the oldest unacknowledged sequence number. Note that SND.UNA is a TCP state variable that is congruent to Counter32 semantics." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsAppEntry 1 } tcpEStatsAppSndNxt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of SND.NXT, the next sequence number to be sent. Note that tcpEStatsAppSndNxt is not monotonic (and thus not a counter) because TCP sometimes retransmits lost data by pulling tcpEStatsAppSndNxt back to the missing data." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsAppEntry 2 } tcpEStatsAppSndMax OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The farthest forward (right most or largest) SND.NXT value. Note that this will be equal to tcpEStatsAppSndNxt except when tcpEStatsAppSndNxt is pulled back during recovery." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsAppEntry 3 } tcpEStatsAppThruOctetsAcked OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets for which cumulative acknowledgments have been received. Note that this will be the sum of changes to tcpEStatsAppSndUna." ::= { tcpEStatsAppEntry 4 } tcpEStatsAppHCThruOctetsAcked OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets for which cumulative acknowledgments have been received, on systems that can receive more than 10 million bits per second. Note that this will be the sum of changes in tcpEStatsAppSndUna." ::= { tcpEStatsAppEntry 5 } tcpEStatsAppRcvNxt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of RCV.NXT. The next sequence number expected on an incoming segment, and the left or lower edge of the receive window. Note that RCV.NXT is a TCP state variable that is congruent to Counter32 semantics." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsAppEntry 6 } tcpEStatsAppThruOctetsReceived OBJECT-TYPE SYNTAX ZeroBasedCounter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets for which cumulative acknowledgments have been sent. Note that this will be the sum of changes to tcpEStatsAppRcvNxt." ::= { tcpEStatsAppEntry 7 } tcpEStatsAppHCThruOctetsReceived OBJECT-TYPE SYNTAX ZeroBasedCounter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets for which cumulative acknowledgments have been sent, on systems that can transmit more than 10 million bits per second. Note that this will be the sum of changes in tcpEStatsAppRcvNxt." ::= { tcpEStatsAppEntry 8 } tcpEStatsAppCurAppWQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of octets of application data buffered by TCP, pending first transmission, i.e. to the left of SND.NXT or SndMax. This data will generally be transmitted (and SND.NXT advanced to the left) as soon as there is available congestion window (cwnd) or receiver window (rwin). This is the amount of data readily available for transmission, without scheduling the application. TCP performance may suffer if there is insufficient queued write data." ::= { tcpEStatsAppEntry 11 } tcpEStatsAppMaxAppWQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of octets of application data buffered by TCP, pending first transmission. This is the maximum value of tcpEStatsAppCurAppWQueue. This pair of objects can be used to determine if insufficient queued data is steady state (suggesting insufficient queue space) or transient (suggesting insufficient application performance or excessive CPU load or scheduler latency)." ::= { tcpEStatsAppEntry 12 } tcpEStatsAppCurAppRQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of octets of application data that has been acknowledged by TCP but not yet delivered to the application." ::= { tcpEStatsAppEntry 13 } tcpEStatsAppMaxAppRQueue OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of octets of application data that has been acknowledged by TCP but not yet delivered to the application." ::= { tcpEStatsAppEntry 14 } -- ================================================================ -- -- Controls for Tuning TCP -- tcpEStatsTuneTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpEStatsTuneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains per connection controls that can be used to work around a number of common problems that plague TCP over some paths. All can be characterized as limiting the growth of the congestion window so as to prevent TCP from overwhelming some component in the path. Entries are retained in this table for the number of seconds indicated by the tcpEStatsConnTableLatency object, after the TCP connection first enters the closed state." ::= { tcpEStats 7 } tcpEStatsTuneEntry OBJECT-TYPE SYNTAX TcpEStatsTuneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is a control that can be used to place limits on each active tcp connection." INDEX { tcpEStatsConnectIndex } ::= { tcpEStatsTuneTable 1 } TcpEStatsTuneEntry ::= SEQUENCE { tcpEStatsTuneLimCwnd Gauge32, tcpEStatsTuneLimSsthresh Gauge32, tcpEStatsTuneLimRwin Gauge32 } tcpEStatsTuneLimCwnd OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "A control to set the maximum congestion window which may be used, in octets." REFERENCE "RFC2581, TCP Congestion Control" ::= { tcpEStatsTuneEntry 1 } tcpEStatsTuneLimSsthresh OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "A control to limit the maximum queue space (in octets) that this TCP connection is likely to occupy during slowstart. It can be implemented with the algorithm described in RFC3742 by setting the max_ssthresh parameter to twice tcpEStatsTuneLimSsthresh. This algorithm can be used to overcome some TCP performance problems over network paths that do not have sufficient buffering to withstand the bursts normally present during slowstart." REFERENCE "RFC3742, Limited Slow-Start for TCP with Large Congestion Windows" ::= { tcpEStatsTuneEntry 2 } tcpEStatsTuneLimRwin OBJECT-TYPE SYNTAX Gauge32 UNITS "octets" MAX-ACCESS read-write STATUS current DESCRIPTION "A control to set the maximum window advertisement which may be sent, in octets." REFERENCE "RFC793, Transmission Control Protocol" ::= { tcpEStatsTuneEntry 3 } -- ================================================================ -- -- TCP Extended Statistics Notifications Group -- tcpEStatsEstablishNotification NOTIFICATION-TYPE OBJECTS { tcpEStatsConnectIndex } STATUS current DESCRIPTION "The indicated connection has been accepted (or alternatively entered the established state)." ::= { tcpEStatsNotifications 1 } tcpEStatsCloseNotification NOTIFICATION-TYPE OBJECTS { tcpEStatsConnectIndex } STATUS current DESCRIPTION "The indicated connection has left the established state" ::= { tcpEStatsNotifications 2 } -- ================================================================ -- -- Conformance Definitions -- tcpEStatsCompliances OBJECT IDENTIFIER ::= { tcpEStatsConformance 1 } tcpEStatsGroups OBJECT IDENTIFIER ::= { tcpEStatsConformance 2 } -- -- Compliance Statements -- tcpEStatsCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for all systems that implement TCP extended statistics." MODULE -- this module MANDATORY-GROUPS { tcpEStatsListenerGroup, tcpEStatsConnectIdGroup, tcpEStatsPerfGroup, tcpEStatsPathGroup, tcpEStatsStackGroup, tcpEStatsAppGroup } GROUP tcpEStatsListenerHCGroup DESCRIPTION "This group is mandatory for all systems that can wrap the values of the 32-bit counters in tcpEStatsListenerGroup in less than one hour." GROUP tcpEStatsPerfOptionalGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsPerfHCGroup DESCRIPTION "This group is mandatory for systems that can wrap the values of the 32-bit counters in tcpEStatsPerfGroup in less than one hour. Note that any system that can attain 10 Mb/s can potentially wrap 32-Bit Octet counters in under one hour." GROUP tcpEStatsPathOptionalGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsPathHCGroup DESCRIPTION "This group is mandatory for systems that can wrap the values of the 32-bit counters in tcpEStatsPathGroup in less than one hour. Note that any system that can attain 10 Mb/s can potentially wrap 32-Bit Octet counters in under one hour." GROUP tcpEStatsStackOptionalGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsAppHCGroup DESCRIPTION "This group is mandatory for systems that can wrap the values of the 32-bit counters in tcpEStatsStackGroup in less than one hour. Note that any system that can attain 10 Mb/s can potentially wrap 32-Bit Octet counters in under one hour." GROUP tcpEStatsAppOptionalGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsTuneOptionalGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsNotificationsGroup DESCRIPTION "This group is optional for all systems." GROUP tcpEStatsNotificationsCtlGroup DESCRIPTION "This group is mandatory for systems that include the tcpEStatsNotificationGroup." OBJECT tcpEStatsControlNotify MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { tcpEStatsCompliances 1 } -- ================================================================ -- -- Units of Conformance -- tcpEStatsListenerGroup OBJECT-GROUP OBJECTS { tcpEStatsListenerTableLastChange, tcpEStatsListenerStartTime, tcpEStatsListenerSynRcvd, tcpEStatsListenerInitial, tcpEStatsListenerEstablished, tcpEStatsListenerAccepted, tcpEStatsListenerExceedBacklog, tcpEStatsListenerCurConns, tcpEStatsListenerMaxBacklog, tcpEStatsListenerCurBacklog, tcpEStatsListenerCurEstabBacklog } STATUS current DESCRIPTION "The tcpEStatsListener group includes objects that provide valuable statistics and debugging information for TCP Listeners." ::= { tcpEStatsGroups 1 } tcpEStatsListenerHCGroup OBJECT-GROUP OBJECTS { tcpEStatsListenerHCSynRcvd, tcpEStatsListenerHCInitial, tcpEStatsListenerHCEstablished, tcpEStatsListenerHCAccepted, tcpEStatsListenerHCExceedBacklog } STATUS current DESCRIPTION "The tcpEStatsListenerHC group includes 64 bit counters in tcpEStatsListenerTable." ::= { tcpEStatsGroups 2 } tcpEStatsConnectIdGroup OBJECT-GROUP OBJECTS { tcpEStatsConnTableLatency, tcpEStatsConnectIndex } STATUS current DESCRIPTION "The tcpEStatsConnectId group includes objects that identify TCP connections and control how long TCP connection entries are retained in the tables." ::= { tcpEStatsGroups 3 } tcpEStatsPerfGroup OBJECT-GROUP OBJECTS { tcpEStatsPerfSegsOut, tcpEStatsPerfDataSegsOut, tcpEStatsPerfDataOctetsOut, tcpEStatsPerfSegsRetrans, tcpEStatsPerfOctetsRetrans, tcpEStatsPerfSegsIn, tcpEStatsPerfDataSegsIn, tcpEStatsPerfDataOctetsIn, tcpEStatsPerfElapsedSecs, tcpEStatsPerfElapsedMicroSecs, tcpEStatsPerfStartTimeStamp, tcpEStatsPerfCurMSS, tcpEStatsPerfPipeSize, tcpEStatsPerfMaxPipeSize, tcpEStatsPerfSmoothedRTT, tcpEStatsPerfCurRTO, tcpEStatsPerfCongSignals, tcpEStatsPerfCurCwnd, tcpEStatsPerfCurSsthresh, tcpEStatsPerfTimeouts, tcpEStatsPerfCurRwinSent, tcpEStatsPerfMaxRwinSent, tcpEStatsPerfZeroRwinSent, tcpEStatsPerfCurRwinRcvd, tcpEStatsPerfMaxRwinRcvd, tcpEStatsPerfZeroRwinRcvd } STATUS current DESCRIPTION "The tcpEStatsPerf group includes those objects that provide basic performance data for a TCP connection." ::= { tcpEStatsGroups 4 } tcpEStatsPerfOptionalGroup OBJECT-GROUP OBJECTS { tcpEStatsPerfSndLimTransRwin, tcpEStatsPerfSndLimTransCwnd, tcpEStatsPerfSndLimTransSnd, tcpEStatsPerfSndLimTimeRwin, tcpEStatsPerfSndLimTimeCwnd, tcpEStatsPerfSndLimTimeSnd } STATUS current DESCRIPTION "The tcpEStatsPerf group includes those objects that provide basic performance data for a TCP connection." ::= { tcpEStatsGroups 5 } tcpEStatsPerfHCGroup OBJECT-GROUP OBJECTS { tcpEStatsPerfHCDataOctetsOut, tcpEStatsPerfHCDataOctetsIn } STATUS current DESCRIPTION "The tcpEStatsPerfHC group includes 64 bit counters in the tcpEStatsPerfTable." ::= { tcpEStatsGroups 6 } tcpEStatsPathGroup OBJECT-GROUP OBJECTS { tcpEStatsControlPath, tcpEStatsPathRetranThresh, tcpEStatsPathNonRecovDAEpisodes, tcpEStatsPathSumOctetsReordered, tcpEStatsPathNonRecovDA } STATUS current DESCRIPTION "The tcpEStatsPath group includes objects that control the creation of the tcpEStatsPathTable, and provide information about the path for each TCP connection." ::= { tcpEStatsGroups 7 } tcpEStatsPathOptionalGroup OBJECT-GROUP OBJECTS { tcpEStatsPathSampleRTT, tcpEStatsPathRTTVar, tcpEStatsPathMaxRTT, tcpEStatsPathMinRTT, tcpEStatsPathSumRTT, tcpEStatsPathCountRTT, tcpEStatsPathMaxRTO, tcpEStatsPathMinRTO, tcpEStatsPathIpTtl, tcpEStatsPathIpTosIn, tcpEStatsPathIpTosOut, tcpEStatsPathPreCongSumCwnd, tcpEStatsPathPreCongSumRTT, tcpEStatsPathPostCongSumRTT, tcpEStatsPathPostCongCountRTT, tcpEStatsPathECNsignals, tcpEStatsPathECERcvd, tcpEStatsPathQuenchRcvd, tcpEStatsPathDupAckEpisodes, tcpEStatsPathRcvRTT, tcpEStatsPathDupAcksOut, tcpEStatsPathCERcvd, tcpEStatsPathECNSent, tcpEStatsPathECNNonceRcvd } STATUS current DESCRIPTION "The tcpEStatsPath group includes objects that provide additional information about the path for each TCP connection." ::= { tcpEStatsGroups 8 } tcpEStatsPathHCGroup OBJECT-GROUP OBJECTS { tcpEStatsPathHCSumRTT } STATUS current DESCRIPTION "The tcpEStatsPathHC group includes 64 bit counters in the tcpEStatsPathTable." ::= { tcpEStatsGroups 9 } tcpEStatsStackGroup OBJECT-GROUP OBJECTS { tcpEStatsControlStack, tcpEStatsStackActiveOpen, tcpEStatsStackMSSSent, tcpEStatsStackMSSRcvd, tcpEStatsStackWinScaleSent, tcpEStatsStackWinScaleRcvd, tcpEStatsStackTimeStamps, tcpEStatsStackECN, tcpEStatsStackWillSendSACK, tcpEStatsStackWillUseSACK, tcpEStatsStackState, tcpEStatsStackNagle, tcpEStatsStackMaxSsCwnd, tcpEStatsStackMaxCaCwnd, tcpEStatsStackMaxSsthresh, tcpEStatsStackMinSsthresh, tcpEStatsStackInRecovery, tcpEStatsStackDupAcksIn, tcpEStatsStackSpuriousFrDetected, tcpEStatsStackSpuriousRtoDetected } STATUS current DESCRIPTION "The tcpEStatsConnState group includes objects that control the creation of the tcpEStatsStackTable, and provide information about the operation of algorithms used within TCP." ::= { tcpEStatsGroups 10 } tcpEStatsStackOptionalGroup OBJECT-GROUP OBJECTS { tcpEStatsStackSoftErrors, tcpEStatsStackSoftErrorReason, tcpEStatsStackSlowStart, tcpEStatsStackCongAvoid, tcpEStatsStackOtherReductions, tcpEStatsStackCongOverCount, tcpEStatsStackFastRetran, tcpEStatsStackSubsequentTimeouts, tcpEStatsStackCurTimeoutCount, tcpEStatsStackAbruptTimeouts, tcpEStatsStackSACKsRcvd, tcpEStatsStackSACKBlocksRcvd, tcpEStatsStackSendStall, tcpEStatsStackDSACKDups, tcpEStatsStackMaxMSS, tcpEStatsStackMinMSS, tcpEStatsStackSndInitial, tcpEStatsStackRecInitial, tcpEStatsStackCurRetxQueue, tcpEStatsStackMaxRetxQueue, tcpEStatsStackCurReasmQueue, tcpEStatsStackMaxReasmQueue } STATUS current DESCRIPTION "The tcpEStatsConnState group includes objects that provide additional information about the operation of algorithms used within TCP." ::= { tcpEStatsGroups 11 } tcpEStatsAppGroup OBJECT-GROUP OBJECTS { tcpEStatsControlApp, tcpEStatsAppSndUna, tcpEStatsAppSndNxt, tcpEStatsAppSndMax, tcpEStatsAppThruOctetsAcked, tcpEStatsAppRcvNxt, tcpEStatsAppThruOctetsReceived } STATUS current DESCRIPTION "The tcpEStatsConnState group includes objects that control the creation of the tcpEStatsAppTable, and provide information about the operation of algorithms used within TCP." ::= { tcpEStatsGroups 12 } tcpEStatsAppHCGroup OBJECT-GROUP OBJECTS { tcpEStatsAppHCThruOctetsAcked, tcpEStatsAppHCThruOctetsReceived } STATUS current DESCRIPTION "The tcpEStatsStackHC group includes 64 bit counters in the tcpEStatsStackTable." ::= { tcpEStatsGroups 13 } tcpEStatsAppOptionalGroup OBJECT-GROUP OBJECTS { tcpEStatsAppCurAppWQueue, tcpEStatsAppMaxAppWQueue, tcpEStatsAppCurAppRQueue, tcpEStatsAppMaxAppRQueue } STATUS current DESCRIPTION "The tcpEStatsConnState group includes objects that provide additional information about how applications are interacting with each TCP connection." ::= { tcpEStatsGroups 14 } tcpEStatsTuneOptionalGroup OBJECT-GROUP OBJECTS { tcpEStatsControlTune, tcpEStatsTuneLimCwnd, tcpEStatsTuneLimSsthresh, tcpEStatsTuneLimRwin } STATUS current DESCRIPTION "The tcpEStatsConnState group includes objects that control the creation of the tcpEStatsConnectionTable, which can be used to set tuning parameters for each TCP connection." ::= { tcpEStatsGroups 15 } tcpEStatsNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { tcpEStatsEstablishNotification, tcpEStatsCloseNotification } STATUS current DESCRIPTION "Notifications sent by a TCP extended statistics agent." ::= { tcpEStatsGroups 16 } tcpEStatsNotificationsCtlGroup OBJECT-GROUP OBJECTS { tcpEStatsControlNotify } STATUS current DESCRIPTION "The tcpEStatsNotificationsCtl group includes the object that controls the creation of the events in the tcpEStatsNotificationsGroup." ::= { tcpEStatsGroups 17 } END -- -- Copyright (C) The Internet Society (2006). -- -- This document is subject to the rights, licenses and restrictions -- contained in BCP 78, and except as set forth therein, the authors -- retain all their rights.