-- extracted from draft-ietf-mpls-telink-mib-00.txt -- at Tue Apr 22 06:12:45 2003 TE-LINK-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue, RowStatus, StorageType FROM SNMPv2-TC InterfaceIndexOrZero, ifIndex FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB; teLinkMIB MODULE-IDENTITY LAST-UPDATED "200304181200Z" -- 18 April 2003 12:00:00 EST ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group" CONTACT-INFO " Martin Dubuc Email: dubuc.consulting@rogers.com Sudheer Dharanikota Email: sudheer@avici.com Thomas D. Nadeau Email: tnadeau@cisco.com Jonathan P. Lang Email: jplang@ieee.org" DESCRIPTION "This MIB contains managed object definitions for MPLS traffic engineering links as defined in: Kompella, K., Rekhter, Y., Berger, L., Link Bundling in MPLS Traffic Engineering Internet Draft , July 2002." -- Revision history. REVISION "200304181200Z" -- 18 April 2003 12:00:00 EST DESCRIPTION "Initial version published as RFC xxxx (to be assigned by RFC Editor)" ::= { mib-2 xxx } -- To be assigned by IANA (experimental 114 can be used -- in the interim) -- Textual Conventions -- Top level components of this MIB -- Notifications teLinkNotifications OBJECT IDENTIFIER ::= { teLinkMIB 0 } -- Tables, Scalars teLinkObjects OBJECT IDENTIFIER ::= { teLinkMIB 1 } -- Conformance teLinkConformance OBJECT IDENTIFIER ::= { teLinkMIB 2 } -- TE Link Table teLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the grouping of component links into TE links and grouping of TE links into bundled links." ::= { teLinkObjects 1 } teLinkEntry OBJECT-TYPE SYNTAX TeLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table exists for each ifEntry with an ifType of teLink(TBD), i.e. for every TE link. An ifEntry in the ifTable must exist before a teLinkEntry is created with the corresponding ifIndex. If a TE link entry in the ifTable is destroyed, then so is the corresponding entry in the teLinkTable. The administrative and operational status values are controlled from the ifEntry. If the link is unnumbered, ifIndex is also used as the outgoing interface identifier." INDEX { ifIndex } ::= { teLinkTable 1 } TeLinkEntry ::= SEQUENCE { teLinkIpAddrType InetAddressType, teLinkIpAddr InetAddress, teLinkRemoteIpAddr InetAddress, teLinkMetric Unsigned32, teLinkMuxCapability INTEGER, teLinkProtectionType INTEGER, teLinkWorkingPriority Unsigned32, teLinkResourceClass Unsigned32, teLinkIncomingIfId InterfaceIndexOrZero, teLinkOutgoingIfId InterfaceIndexOrZero, teLinkRowStatus RowStatus, teLinkStorageType StorageType } teLinkIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "For IPv4 and IPv6 numbered links, this object represents the IP address type associated with the TE link. For unnumbered links, a value of unknown(0) must be used." ::= { teLinkEntry 1 } teLinkIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "For IPv4 and IPv6 numbered links, this object represents the IP address associated with the TE link." ::= { teLinkEntry 2 } teLinkRemoteIpAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The remote IP address associated with the TE link (IPv4 and IPv6 numbered links)." ::= { teLinkEntry 3 } teLinkMetric OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric." REFERENCE "[BUNDLING]" ::= { teLinkEntry 4 } teLinkMuxCapability OBJECT-TYPE SYNTAX INTEGER { packetSwitch1(1), packetSwitch2(2), packetSwitch3(3), packetSwitch4(4), layer2Switch(51), tdm(100), lambdaSwitch(150), fiberSwitch(200) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link multiplex capability of the TE link, which is derived from its component links. All component links within the same TE link must have the same link multiplex capability." REFERENCE "[GMPLS-OSPF]" ::= { teLinkEntry 5 } teLinkProtectionType OBJECT-TYPE SYNTAX INTEGER { extraTraffic(1), unprotected(2), shared(3), dedicated1For1(4), dedicated1Plus1(5), enhanced(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link protection type of the TE link." REFERENCE "[GMPLS-OSPF]" ::= { teLinkEntry 6 } teLinkWorkingPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents a priority value such that a new connection with a higher priority, i.e. numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link." REFERENCE "[GMPLS-OSPF]" ::= { teLinkEntry 7 } teLinkResourceClass OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within a link bundle must have the same resource class." ::= { teLinkEntry 8 } teLinkIncomingIfId OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "For unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link." REFERENCE "[BUNDLING]" ::= { teLinkEntry 9 } teLinkOutgoingIfId OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "If the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR." REFERENCE "[BUNDLING]" ::= { teLinkEntry 10 } teLinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkRowStatus is active." ::= { teLinkEntry 11 } teLinkStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkEntry 12 } -- End of teLinkTable -- TE Link Descriptor Table teLinkDescriptorTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the link descriptors associated with the TE links." ::= { teLinkObjects 2 } teLinkDescriptorEntry OBJECT-TYPE SYNTAX TeLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created for every TE link descriptor. An ifEntry in the ifTable must exist before a teLinkDescriptorEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkDescriptorTable that use the ifIndex of this TE link." INDEX { ifIndex, teLinkDescriptorId } ::= { teLinkDescriptorTable 1 } TeLinkDescriptorEntry ::= SEQUENCE { teLinkDescriptorId Unsigned32, teLinkEncodingType INTEGER, teLinkDescrPriority Unsigned32, teLinkMinReservableBandwidth Unsigned32, teLinkMaxReservableBandwidth Unsigned32, teLinkDescrRowStatus RowStatus, teLinkDescrStorageType StorageType } teLinkDescriptorId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the link descriptor identifier." ::= { teLinkDescriptorEntry 1 } teLinkEncodingType OBJECT-TYPE SYNTAX INTEGER { packet(1), ethernet(2), ansiEtsiPdh(3), sdhItuSonetAnsi(5), digitalWrapper(7), lambda(8), fiber(9), fiberChannel(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link encoding type." REFERENCE "[RFC3471]" ::= { teLinkDescriptorEntry 2 } teLinkDescrPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the lowest priority at which that link encoding type is available." REFERENCE "[GMPLS-OSPF]" ::= { teLinkDescriptorEntry 3 } teLinkMinReservableBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the minimum reservable bandwidth on the TE link. This is derived from the union of the minimum reservable bandwidth of all the component links associated with the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OSPF]" ::= { teLinkDescriptorEntry 4 } teLinkMaxReservableBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OSPF]" ::= { teLinkDescriptorEntry 5 } teLinkDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkDescrRowStatus is active." ::= { teLinkDescriptorEntry 6 } teLinkDescrStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkDescriptorEntry 7 } -- End of teLinkDescriptorTable -- TE Link Shared Risk Link Group Table teLinkSrlgTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the SRLGs associated with TE links." ::= { teLinkObjects 3 } teLinkSrlgEntry OBJECT-TYPE SYNTAX TeLinkSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about a SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkSrlgTable that use the ifIndex of this TE link." INDEX { ifIndex, srlg } ::= { teLinkSrlgTable 1 } TeLinkSrlgEntry ::= SEQUENCE { srlg Unsigned32, srlgRowStatus RowStatus, srlgStorageType StorageType } srlg OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This identifies a SRLG supported by the TE link." REFERENCE "[GMPLS-OSPF]" ::= { teLinkSrlgEntry 1 } srlgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when srlgRowStatus is active." ::= { teLinkSrlgEntry 2 } srlgStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkSrlgEntry 3 } -- End of teLinkSrlgTable -- TE Link Bandwidth Table teLinkBandwidthTable OBJECT-TYPE SYNTAX SEQUENCE OF TeLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the priority-based bandwidth table for TE links." ::= { teLinkObjects 4 } teLinkBandwidthEntry OBJECT-TYPE SYNTAX TeLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about the priority-based bandwidth of TE links. An ifEntry in the ifTable must exist before a teLinkBandwidthEntry using the same ifIndex is created. If a TE link entry in the ifTable is destroyed, then so are all entries in the teLinkBandwidthTable that use the ifIndex of this TE link." INDEX { ifIndex, teLinkPriority } ::= { teLinkBandwidthTable 1 } TeLinkBandwidthEntry ::= SEQUENCE { teLinkPriority Unsigned32, teLinkUnreservedBandwidth Unsigned32, teLinkMaximumLspBandwidth Unsigned32, teLinkBandwidthRowStatus RowStatus, teLinkBandwidthStorageType StorageType } teLinkPriority OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute specifies the priority. It should be mapped to a number between 0 and 7" REFERENCE "[GMPLS-OSPF]" ::= { teLinkBandwidthEntry 1 } teLinkUnreservedBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second." REFERENCE "[BUNDLING]" ::= { teLinkBandwidthEntry 2 } teLinkMaximumLspBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the TE link maximum LSP bandwidth at priority p. It is the maximum of all maximum LSP bandwidth at priority p of the component links associated with the TE link (excludes all links that are strictly used as protecting links). This value is an estimate in units of 1,000 bits per second." REFERENCE "[BUNDLING]" ::= { teLinkBandwidthEntry 3 } teLinkBandwidthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when teLinkBandwidthRowStatus is active." ::= { teLinkBandwidthEntry 4 } teLinkBandwidthStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { teLinkBandwidthEntry 5 } -- End of teLinkBandwidthTable -- Component Link Table componentLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the component link parameters." ::= { teLinkObjects 5 } componentLinkEntry OBJECT-TYPE SYNTAX ComponentLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table exists for each ifEntry that represents a component link. An ifEntry must exist in the ifTable before a componentLinkEntry is created with the corresponding ifIndex. If an entry representing a component link is destroyed in the ifTable, then so is the corresponding entry in the componentLinkTable. The administrative and operational status values are controlled from the ifEntry." INDEX { ifIndex } ::= { componentLinkTable 1 } ComponentLinkEntry ::= SEQUENCE { componentLinkMuxCapability INTEGER, componentLinkPreferredProtection INTEGER, componentLinkCurrentProtection INTEGER, componentLinkRowStatus RowStatus, componentLinkStorageType StorageType } componentLinkMuxCapability OBJECT-TYPE SYNTAX INTEGER { packetSwitch1(1), packetSwitch2(2), packetSwitch3(3), packetSwitch4(4), layer2Switch(51), tdm(100), lambdaSwitch(150), fiberSwitch(200) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies link multiplexing capabilities of the component link." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkEntry 1 } componentLinkPreferredProtection OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies whether this component link is a primary or secondary entity." ::= { componentLinkEntry 2 } componentLinkCurrentProtection OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies whether this component link is currently used as primary or secondary link." ::= { componentLinkEntry 3 } componentLinkRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkRowStatus is active." ::= { componentLinkEntry 4 } componentLinkStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkEntry 5 } -- End of componentLinkTable -- Component Link Descriptor Table componentLinkDescriptorTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the link descriptors associated with the component links." ::= { teLinkObjects 6 } componentLinkDescriptorEntry OBJECT-TYPE SYNTAX ComponentLinkDescriptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created for every component link descriptor. An ifEntry in the ifTable must exist before a componentLinkDescriptorEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkDescriptorTable that use the ifIndex of this component link." INDEX { ifIndex, componentLinkDescrId } ::= { componentLinkDescriptorTable 1 } ComponentLinkDescriptorEntry ::= SEQUENCE { componentLinkDescrId Unsigned32, componentLinkEncodingType INTEGER, componentLinkDescrPriority Unsigned32, componentLinkMinReservBandwidth Unsigned32, componentLinkMaxReservBandwidth Unsigned32, componentLinkDescrRowStatus RowStatus, componentLinkDescrStorageType StorageType } componentLinkDescrId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the link descriptor identifier." ::= { componentLinkDescriptorEntry 1 } componentLinkEncodingType OBJECT-TYPE SYNTAX INTEGER { packet(1), ethernet(2), ansiEtsiPdh(3), sdhItuSonetAnsi(5), digitalWrapper(7), lambda(8), fiber(9), fiberChannel(11) } MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the component link encoding type." REFERENCE "[RFC3471]" ::= { componentLinkDescriptorEntry 2 } componentLinkDescrPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the lowest priority at which that link encoding type is available for the component link." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkDescriptorEntry 3 } componentLinkMinReservBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the minimum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkDescriptorEntry 4 } componentLinkMaxReservBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the maximum reservable bandwidth on the component link. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkDescriptorEntry 5 } componentLinkDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkDescrRowStatus is active." ::= { componentLinkDescriptorEntry 6 } componentLinkDescrStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkDescriptorEntry 7 } -- End of componentLinkDescriptorTable -- Component Link Bandwidth Table componentLinkBandwidthTable OBJECT-TYPE SYNTAX SEQUENCE OF ComponentLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the priority-based bandwidth for component links." ::= { teLinkObjects 7 } componentLinkBandwidthEntry OBJECT-TYPE SYNTAX ComponentLinkBandwidthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table contains information about the priority-based bandwidth on component links. An ifEntry in the ifTable must exist before a componentLinkBandwidthEntry using the same ifIndex is created. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkBandwidthTable that use the ifIndex of this component link." INDEX { ifIndex, componentLinkPriority } ::= { componentLinkBandwidthTable 1 } ComponentLinkBandwidthEntry ::= SEQUENCE { componentLinkPriority Unsigned32, componentLinkUnreservedBandwidth Unsigned32, componentLinkMaximumLspBandwidth Unsigned32, componentLinkBandwidthRowStatus RowStatus, componentLinkBwStorageType StorageType } componentLinkPriority OBJECT-TYPE SYNTAX Unsigned32 (1..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This attribute specifies the priority. It should be mapped to a number between 0 and 7." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkBandwidthEntry 1 } componentLinkUnreservedBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute specifies the component link unreserved bandwidth at priority p. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OPSF]" ::= { componentLinkBandwidthEntry 2 } componentLinkMaximumLspBandwidth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This attribute specifies the component link maximum LSP bandwidth at priority p. This value is an estimate in units of 1,000 bits per second." REFERENCE "[GMPLS-OSPF]" ::= { componentLinkBandwidthEntry 3 } componentLinkBandwidthRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table. All read-create objects can only be changed when componentLinkBandwidthRowStatus is active." ::= { componentLinkBandwidthEntry 4 } componentLinkBwStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row." ::= { componentLinkBandwidthEntry 5 } -- End of componentLinkBandwidthTable -- Notification Configuration teLinkNotifEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of the TE link notifications, otherwise these notifications are not emitted." DEFVAL { false } ::= { teLinkObjects 8 } -- Notifications -- TE Link Notifications linkBundleMismatch NOTIFICATION-TYPE OBJECTS { teLinkIpAddrType, teLinkIpAddr, teLinkRemoteIpAddr } STATUS current DESCRIPTION "This notification is generated when a mismatch is found on a bundled link. Such mismatch can be detected for instance if one of the traffic engineering parameters is not consistent across all TE links within a bundled link (resource class, etc.)." ::= { teLinkNotifications 1 } -- End of notifications -- Module compliance teLinkGroups OBJECT IDENTIFIER ::= { teLinkConformance 1 } teLinkCompliances OBJECT IDENTIFIER ::= { teLinkConformance 2 } teLinkFullModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the configuration and monitoring of TE Link MIB." MODULE -- this module -- The mandatory groups have to be implemented -- by all devices supporting TE links. However, they may all -- be supported as read-only objects in the case where automatic -- configuration is supported. MANDATORY-GROUPS { teLinkGroup, teLinkBandwidthGroup, componentLinkBandwidthGroup } GROUP teLinkSrlgGroup DESCRIPTION "This group is mandatory for G-MPLS enabled devices." GROUP teLinkNotificationGroup DESCRIPTION "This group is mandatory for equipment that support TE link notifications." -- teLinkTable OBJECT teLinkIpAddrType SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "The dns(16) address type need not be supported. The ipv4(1) and ipv6(2) address types need not be supported if numbered links are not supported. The unknown(0) address type need not be supported if unnumbered links are not supported." OBJECT teLinkIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkRemoteIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkProtectionType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkDescriptorTable OBJECT teLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMinReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMaxReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkDescrStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkSrlgTable OBJECT srlgRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT srlgStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- teLinkBandwidthTable OBJECT teLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT teLinkBandwidthStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkTable OBJECT componentLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMaxReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkDescriptorTable OBJECT componentLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) state need not be supported." OBJECT componentLinkDescrStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." -- componentLinkBandwidthTable OBJECT componentLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkBwStorageType SYNTAX INTEGER { other(1) } DESCRIPTION "Only other(1) needs to be supported." ::= { teLinkCompliances 1 } teLinkMonModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the monitoring of TE link MIB." MODULE -- this module -- The mandatory groups have to be implemented -- by all devices supporting TE links. However, they may all -- be supported as read-only objects in the case where manual -- configuration is unsupported. MANDATORY-GROUPS { teLinkGroup, teLinkBandwidthGroup, componentLinkBandwidthGroup } GROUP teLinkSrlgGroup DESCRIPTION "This group is mandatory for G-MPLS enabled devices." GROUP teLinkNotificationGroup DESCRIPTION "This group is optional." -- teLinkTable OBJECT teLinkIpAddrType SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "The dns(16) address type need not be supported. The ipv4(1) and ipv6(2) address types need not be supported if numbered links are not supported. The unknown(0) address type need not be supported if unnumbered links are not supported." OBJECT teLinkIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkRemoteIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "Size of TE link IP address depends on type of TE link. TE link IP address size is zero if link is unnumbered, four if link IP address is IPv4 and sixteen if link IP address is IPv6." OBJECT teLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkProtectionType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkWorkingPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkDescriptorTable OBJECT teLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMinReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkMaxReservableBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT teLinkDescrStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkSrlgTable OBJECT srlgRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT srlgStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- teLinkBandwidthTable OBJECT teLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT teLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT teLinkBandwidthStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkTable OBJECT componentLinkMuxCapability MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkPreferredProtection MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMaxReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkDescriptorTable OBJECT componentLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkDescrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkMinReservBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkDescrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) state need not be supported." OBJECT componentLinkDescrStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." -- componentLinkBandwidthTable OBJECT componentLinkMaximumLspBandwidth MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT componentLinkBandwidthRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT componentLinkBwStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." ::= { teLinkCompliances 2 } -- Units of conformance teLinkGroup OBJECT-GROUP OBJECTS { teLinkIpAddrType, teLinkIpAddr, teLinkRemoteIpAddr, teLinkMetric, teLinkMuxCapability, teLinkProtectionType, teLinkWorkingPriority, teLinkResourceClass, teLinkIncomingIfId, teLinkOutgoingIfId, teLinkRowStatus, teLinkStorageType, teLinkEncodingType, teLinkDescrPriority, teLinkMinReservableBandwidth, teLinkMaxReservableBandwidth, teLinkDescrRowStatus, teLinkDescrStorageType, componentLinkMuxCapability, componentLinkPreferredProtection, componentLinkCurrentProtection, componentLinkRowStatus, componentLinkStorageType, teLinkNotifEnable } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of resources associated with TE links." ::= { teLinkGroups 1 } teLinkSrlgGroup OBJECT-GROUP OBJECTS { srlgRowStatus, srlgStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of SRLG resources associated with TE links." ::= { teLinkGroups 2 } teLinkBandwidthGroup OBJECT-GROUP OBJECTS { teLinkUnreservedBandwidth, teLinkMaximumLspBandwidth, teLinkBandwidthRowStatus, teLinkBandwidthStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of the priority-based bandwidth resources associated with TE links and component links." ::= { teLinkGroups 3 } componentLinkBandwidthGroup OBJECT-GROUP OBJECTS { componentLinkEncodingType, componentLinkDescrPriority, componentLinkMinReservBandwidth, componentLinkMaxReservBandwidth, componentLinkDescrRowStatus, componentLinkDescrStorageType, componentLinkUnreservedBandwidth, componentLinkMaximumLspBandwidth, componentLinkBandwidthRowStatus, componentLinkBwStorageType } STATUS current DESCRIPTION "Collection of objects needed for the monitoring of bandwidth parameters associated with component links." ::= { teLinkGroups 4 } teLinkNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { linkBundleMismatch } STATUS current DESCRIPTION "Set of notifications implemented in this module. None is mandatory." ::= { teLinkGroups 5 } -- End of TE-LINK-MIB END -- -- -- Copyright (C) The Internet Society (2003). All Rights Reserved. -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this docu- -- ment itself may not be modified in any way, such as by removing the -- copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of develop- -- ing Internet standards in which case the procedures for copyrights -- defined in the Internet Standards process must be followed, or as -- required to translate it into languages other than English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. This -- document and the information contained herein is provided on an "AS -- IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK -- FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT -- LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL -- NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY -- OR FITNESS FOR A PARTICULAR PURPOSE.