-- extracted from draft-ietf-adslmib-vdsl-ext-mcm-06.txt -- at Tue Jan 18 06:23:37 2005 VDSL-LINE-EXT-MCM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, transmission, Unsigned32 FROM SNMPv2-SMI -- [RFC2578] RowStatus FROM SNMPv2-TC -- [RFC2579] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] ifIndex FROM IF-MIB -- [RFC2863] vdslLineConfProfileName FROM VDSL-LINE-MIB; -- [RFC3728] vdslExtMCMMIB MODULE-IDENTITY LAST-UPDATED "200501160000Z" -- January 16, 2005 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: P.O. Box 37324 Raleigh NC 27627-732 Email: sneedmike@hotmail.com Phone: +1 206 600 7022 Co-Chair: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 Co-editor: Menachem Dodge ECI Telecom Ltd. Postal: 30 hasivim St. Petach Tikva 49517, Israel. Email: mbdodge@ieee.org Phone: +972 3 926 8421 Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142 " DESCRIPTION "The VDSL-LINE-MIB found in RFC 3728 defines objects for the management of a pair of VDSL transceivers at each end of the VDSL line. The VDSL-LINE-MIB configures and monitors the line code independent parameters (TC layer) of the VDSL line. This MIB module is an optional extension of the VDSL-LINE-MIB and defines objects for configuration and monitoring of the line code specific (LCS) elements (PMD layer) for VDSL lines using MCM coding. The objects in this extension MIB MUST NOT be used for VDSL lines using Single Carrier Modulation (SCM) line coding. If an object in this extension MIB is referenced by a line which does not use MCM, it has no effect on the operation of that line. Naming Conventions: Vtuc -- (VTUC) transceiver at near (Central) end of line Vtur -- (VTUR) transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current LCS -- Line Code Specific Max -- Maximum PSD -- Power Spectral Density Rx -- Receive Tx -- Transmit Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices." -- RFC Ed.: replace XXXX with assigned number & remove this note REVISION "200501160000Z" -- January 16, 2005 DESCRIPTION "Initial version, published as RFC XXXX." -- RFC Ed.: replace XX with assigned number & remove this note ::= { transmission XX } -- To be assigned by IANA -- RFC Ed.: we suggest to put it under { transmission 228 } because -- this is the next available number, transmission 227 -- would be used for the SCM MIB. vdslLineExtMCMMib OBJECT IDENTIFIER ::= { vdslExtMCMMIB 1 } vdslLineExtMCMMibObjects OBJECT IDENTIFIER ::= {vdslLineExtMCMMib 1} -- -- Multiple carrier modulation (MCM) configuration profile tables -- vdslLineMCMConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains additional information on multiple carrier VDSL lines. One entry in this table reflects a profile defined by a manager which can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 1 } vdslLineMCMConfProfileEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of a multiple carrier modulation VDSL modem." INDEX { vdslLineConfProfileName } ::= { vdslLineMCMConfProfileTable 1 } VdslLineMCMConfProfileEntry ::= SEQUENCE { vdslLineMCMConfProfileTxWindowLength Unsigned32, vdslLineMCMConfProfileRowStatus RowStatus } vdslLineMCMConfProfileTxWindowLength OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "samples" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the length of the transmit window, counted in samples at the sampling rate corresponding to the negotiated value of N." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileEntry 1 } vdslLineMCMConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile is activated by setting this object to `active'. When `active' is set, the system will validate the profile. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileEntry 2 } vdslLineMCMConfProfileTxBandTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxBandEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains transmit band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 2 } vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileTxBandEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a transmit band descriptor, which is defined by a start and a stop tone index." INDEX { vdslLineConfProfileName, vdslLineMCMConfProfileTxBandNumber } ::= { vdslLineMCMConfProfileTxBandTable 1 } VdslLineMCMConfProfileTxBandEntry ::= SEQUENCE { vdslLineMCMConfProfileTxBandNumber Unsigned32, vdslLineMCMConfProfileTxBandStart Unsigned32, vdslLineMCMConfProfileTxBandStop Unsigned32, vdslLineMCMConfProfileTxBandRowStatus RowStatus } vdslLineMCMConfProfileTxBandNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this band descriptor entry." ::= { vdslLineMCMConfProfileTxBandEntry 1 } vdslLineMCMConfProfileTxBandStart OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "Start tone index for this band." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileTxBandEntry 2 } vdslLineMCMConfProfileTxBandStop OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "Stop tone index for this band." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileTxBandEntry 3 } vdslLineMCMConfProfileTxBandRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Each entry must be internally consistent, the Stop Tone must be greater than the Start Tone. Each entry must also be externally consistent, all entries indexed by a specific profile must not overlap. Validation of the profile will check both internal and external consistency. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileTxBandEntry 4 } vdslLineMCMConfProfileRxBandTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileRxBandEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains receive band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands with a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 3 } vdslLineMCMConfProfileRxBandEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileRxBandEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a transmit band descriptor, which is defined by a start and a stop tone index." INDEX { vdslLineConfProfileName, vdslLineMCMConfProfileRxBandNumber } ::= { vdslLineMCMConfProfileRxBandTable 1 } VdslLineMCMConfProfileRxBandEntry ::= SEQUENCE { vdslLineMCMConfProfileRxBandNumber Unsigned32, vdslLineMCMConfProfileRxBandStart Unsigned32, vdslLineMCMConfProfileRxBandStop Unsigned32, vdslLineMCMConfProfileRxBandRowStatus RowStatus } vdslLineMCMConfProfileRxBandNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this band descriptor entry." ::= { vdslLineMCMConfProfileRxBandEntry 1 } vdslLineMCMConfProfileRxBandStart OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "Start tone index for this band." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileRxBandEntry 2 } vdslLineMCMConfProfileRxBandStop OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "Stop tone index for this band." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileRxBandEntry 3 } vdslLineMCMConfProfileRxBandRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Each entry must be internally consistent, the Stop Tone must be greater than the Start Tone. Each entry must also be externally consistent, all entries indexed by a specific profile must not overlap. Validation of the profile will check both internal and external consistency. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileRxBandEntry 4 } vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains transmit PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL line. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 4 } vdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileTxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone." INDEX { vdslLineConfProfileName, vdslLineMCMConfProfileTxPSDNumber } ::= { vdslLineMCMConfProfileTxPSDTable 1 } VdslLineMCMConfProfileTxPSDEntry ::= SEQUENCE { vdslLineMCMConfProfileTxPSDNumber Unsigned32, vdslLineMCMConfProfileTxPSDTone Unsigned32, vdslLineMCMConfProfileTxPSDPSD Unsigned32, vdslLineMCMConfProfileTxPSDRowStatus RowStatus } vdslLineMCMConfProfileTxPSDNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this mask descriptor entry." ::= { vdslLineMCMConfProfileTxPSDEntry 1 } vdslLineMCMConfProfileTxPSDTone OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "The tone index for which the PSD is being specified." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileTxPSDEntry 2 } vdslLineMCMConfProfileTxPSDPSD OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.5dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Power Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileTxPSDEntry 3 } vdslLineMCMConfProfileTxPSDRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileTxPSDEntry 4 } vdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains transmit maximum PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 5 } vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileMaxTxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a transmit PSD mask descriptor, which defines the maximum power spectral density (PSD) for a tone." INDEX { vdslLineConfProfileName, vdslLineMCMConfProfileMaxTxPSDNumber } ::= { vdslLineMCMConfProfileMaxTxPSDTable 1 } VdslLineMCMConfProfileMaxTxPSDEntry ::= SEQUENCE { vdslLineMCMConfProfileMaxTxPSDNumber Unsigned32, vdslLineMCMConfProfileMaxTxPSDTone Unsigned32, vdslLineMCMConfProfileMaxTxPSDPSD Unsigned32, vdslLineMCMConfProfileMaxTxPSDRowStatus RowStatus } vdslLineMCMConfProfileMaxTxPSDNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this band descriptor entry." ::= { vdslLineMCMConfProfileMaxTxPSDEntry 1 } vdslLineMCMConfProfileMaxTxPSDTone OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "The tone index for which the PSD is being specified. There must not be multiple rows defined, for a particular profile, with the same value for this field." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 } vdslLineMCMConfProfileMaxTxPSDPSD OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.5dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Power Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 } vdslLineMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. There must be only one entry in this table for each tone associated with a specific profile. This will be checked during the validation process. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 } vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains maximum receive PSD mask descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one tone within a multiple carrier modulation (MCM) VDSL modem. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use MCM, it has no effect on the operation of that line. All read-create-objects defined in this table SHOULD be stored persistently." ::= { vdslLineExtMCMMibObjects 6 } vdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE SYNTAX VdslLineMCMConfProfileMaxRxPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a transmit PSD mask descriptor, which defines the power spectral density (PSD) for a tone." INDEX { vdslLineConfProfileName, vdslLineMCMConfProfileMaxRxPSDNumber } ::= { vdslLineMCMConfProfileMaxRxPSDTable 1 } VdslLineMCMConfProfileMaxRxPSDEntry ::= SEQUENCE { vdslLineMCMConfProfileMaxRxPSDNumber Unsigned32, vdslLineMCMConfProfileMaxRxPSDTone Unsigned32, vdslLineMCMConfProfileMaxRxPSDPSD Unsigned32, vdslLineMCMConfProfileMaxRxPSDRowStatus RowStatus } vdslLineMCMConfProfileMaxRxPSDNumber OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index for this band descriptor entry." ::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 } vdslLineMCMConfProfileMaxRxPSDTone OBJECT-TYPE SYNTAX Unsigned32 (1..4096) MAX-ACCESS read-create STATUS current DESCRIPTION "The tone index for which the PSD is being specified. There must not be multiple rows defined, for a particular profile, with the same value for this field." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 } vdslLineMCMConfProfileMaxRxPSDPSD OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.5dBm/Hz" MAX-ACCESS read-create STATUS current DESCRIPTION "Power Spectral Density level in steps of 0.5dBm/Hz with an offset of -140dBm/Hz." REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM ::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 } vdslLineMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. There must be only one entry in this table for each tone associated with a specific profile. This will be checked during the validation process. None of the columns in this row may be modified while the row is in the 'active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines." ::= { vdslLineMCMConfProfileMaxRxPSDEntry 4 } -- conformance information vdslLineExtMCMConformance OBJECT IDENTIFIER ::= { vdslLineExtMCMMib 2 } vdslLineExtMCMGroups OBJECT IDENTIFIER ::= { vdslLineExtMCMConformance 1 } vdslLineExtMCMCompliances OBJECT IDENTIFIER ::= { vdslLineExtMCMConformance 2 } vdslLineExtMCMMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which manage VDSL interfaces." MODULE -- this module MANDATORY-GROUPS { vdslLineExtMCMGroup } ::= { vdslLineExtMCMCompliances 1 } -- units of conformance vdslLineExtMCMGroup OBJECT-GROUP OBJECTS { vdslLineMCMConfProfileTxWindowLength, vdslLineMCMConfProfileRowStatus, vdslLineMCMConfProfileTxBandStart, vdslLineMCMConfProfileTxBandStop, vdslLineMCMConfProfileTxBandRowStatus, vdslLineMCMConfProfileRxBandStart, vdslLineMCMConfProfileRxBandStop, vdslLineMCMConfProfileRxBandRowStatus, vdslLineMCMConfProfileTxPSDTone, vdslLineMCMConfProfileTxPSDPSD, vdslLineMCMConfProfileTxPSDRowStatus, vdslLineMCMConfProfileMaxTxPSDTone, vdslLineMCMConfProfileMaxTxPSDPSD, vdslLineMCMConfProfileMaxTxPSDRowStatus, vdslLineMCMConfProfileMaxRxPSDTone, vdslLineMCMConfProfileMaxRxPSDPSD, vdslLineMCMConfProfileMaxRxPSDRowStatus } STATUS current DESCRIPTION "A collection of objects providing configuration information for a VDSL line based upon multiple carrier modulation modem." ::= { vdslLineExtMCMGroups 1 } END -- -- Copyright (C) The Internet Society (2005). This document is subject -- to the rights, licenses and restrictions contained in BCP 78 and -- except as set forth therein, the authors retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- -- Intellectual Property -- -- The IETF takes no position regarding the validity or scope of any -- Intellectual Property Rights or other rights that might be claimed to -- pertain to the implementation or use of the technology described in -- this document or the extent to which any license under such rights -- might or might not be available; nor does it represent that it has -- made any independent effort to identify any such rights. Information -- on the procedures with respect to rights in RFC documents can be -- found in BCP 78 and BCP 79. -- -- Copies of IPR disclosures made to the IETF Secretariat and any -- assurances of licenses to be made available, or the result of an -- attempt made to obtain a general license or permission for the use -- of such proprietary rights by implementers or users of this -- specification can be obtained from the IETF on-line IPR repository -- at http://www.ietf.org/ipr. -- -- The IETF invites any interested party to bring to its attention any -- copyrights, patents or patent applications, or other proprietary -- rights that may cover technology that may be required to implement -- this standard. Please address the information to the IETF at ietf- -- ipr@ietf.org.